BioMerieux 416036 MODEM RADIO ETHERNET LABGUARD 3 IS USED TO RECEIVE MEASURES OF PHYSICAL PARAMETERS IN LABORATORY SUCH AS TEMPERATURE, HUMIDITY, CO2, ETC. User Manual Quick start guide

Download:
Mirror Download [FCC.gov]
Document ID	2159690
Application ID	XsqcQ05o97WAvYiS630R2Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	232.07kB (2900816 bits)
Date Submitted	2014-01-07 00:00:00
Date Available	2014-01-07 00:00:00
Creation Date	2013-12-24 10:56:30
Producing Software	Antenna House PDF Output Library 6.0.396 (Windows)
Document Lastmod	2013-12-24 10:56:30
Document Title	Quick start guide
Document Creator	AH XSL Formatter V6.0 MR8 for Windows : 6.0.9.10681 (2013/04/23 18:22JST)

Intentionally left blank.
Document history
VERSION
DATE
05/11/2013
MODIFICATIONS
Creation
User manual - Pictograms
Note
Equipment optimization tip
Prohibited action notice
Noteworthy point warning
Danger or potential risk warning
Reminder of the pre-requisites for implementation of the next instructions
™
Labguard is one of bioMérieux's registered trademarks.
The information and graphs contained in this manual are not binding. bioMérieux therefore reserves
the right to implement changes to the document without prior notice.
bioMérieux will not approve any modifications whatsoever to the equipment implemented by
the user. bioMérieux shall under no circumstance be held liable for any direct or
consequential injury or damage whatsoever suffered by the user or by any third party, as a
result of modifications to the equipment.
• This equipment is for professional use only.
• Users are required to read all the accompanying documents, including the statutory
information, before using the equipment.
Contents
Unpacking the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Learning about the equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
™
Labguard 3D equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Understanding the indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Technical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Options and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Equipment conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Industry conformity Canada (IC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EC compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compliance statement
13
13
13
14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1
Unpacking the device
Check that the device has not been damaged during transport. Then check that all the accessories
listed below are present.
Transmitter
• RJ45 cable 3 m
• µUSB/USB cable 2 m
• Unit
• Unit support
Labguard 3
RECEPT_QSG_EN-A
2
Learning about the equipment
Labguard 3D™ equipment
™
With Labguard 3D equipment, you can:
• Simultaneously measure the different physical parameters of the laboratory (temperature,
humidity, CO2).
• Provide alerts with visual alarms in real time in case of anomalies.
®
• Save and transfer data and alarms to the Labguard software.
Front
Accessory connector
Ethernet connector
MicroUSB connector
Labguard 3
RECEPT_QSG_EN-A
3
Installing the device
1. Fix the receiver support to the wall or to the unit to be monitored using the two screws or
adhesive strips at the rear of the support.
2. Slide the device into the support.
3. Connect the Ethernet cable.
4. In the case where the installation is not PoE, plug in the external power source using the
microUSB connector.
Labguard 3
RECEPT_QSG_EN-A
4
Understanding the indicator lights
The indicator lights present on the front of the unit show the status of the Ethernet connection.
Indicator lights
Status
Device connected to mains power supply
Alarm in communication network
Labguard 3
RECEPT_QSG_EN-A
5
Technical characteristics
Environmental
conditions
Altitude
Temperature
Relative humidity (Rh)
Mains power supply
up to 2,000 m
from 0 to 40°C max.
from 10 to 80%
Input:
100-240 VAC;
50/60 Hz; 0.3 A
Product power supply Mains power:
• 5V
48 V
Power Over Ethernet
(IEEE 802.3af)
Pollution level
Output:
5V
; 1 A; 5 W
; 1 A; 5 W
; Class 1; 0.44 to 3.84 W
Atmospheric pressure
Installation category
Device dimensions (W x H x D)
700 hPa to 1,100 hPa
Type II according to Directive CEI 664
Device (mm):
Device in packaging (mm):
Device weight
• 55 x 103 x 31
Device (g):
• 167 x 133 x 74
Device in packaging (g):
• 90
• 305
• Ethernet
• USB
• Labguard 3D sensor
Emission bandwidth: Range:
Connectivity
Wireless
• 865 to 868 Mhz,
60 channels
• 868 to 868.8 Mhz,
12 channels
• 902 to 912 Mhz,
20 channels
• 433.05 to
434.79 Mhz,
8 channels
Labguard 3
10
• 100 m inside
• 400 m outside
RECEPT_QSG_EN-A
6
Maintenance
Disposal
Recycle the lithium batteries in accordance with enforceable regulations.
Dispose of them by the appropriate means put in place.
Cleaning the device
Clean the equipment using a cloth dampened with ethanol or any other common disinfectant.
However, avoid using formol, solvents, heat greater than 80°C (flames, autoclaving) or cleaning by
dipping or spraying.
Labguard 3
11
RECEPT_QSG_EN-A
7
Options and accessories
Use the following options and accessories for optimum use of the device.
Reference
416053
416055
416054
416056
416057
416070
416072
Designation
Mains power supply µUSB_EU
Mains power supply µUSB_UK
Mains power supply µUSB_US
Mains power supply µUSB_AU/CN
Sensor extension cable 1 m
µUSB/USB cable 2 m
RJ45 cable 3 m
Labguard 3
12
RECEPT_QSG_EN-A
8
Equipment conformity
FCC compliance
This equipment has been declared in compliance with FCC regulations, section 15, applicable to class
B digital equipments. These regulations are designed to provide adequate protection against harmful
interferences in a residential installation. This equipment generates, uses and may emit radio-electric
waves. It can generate interferences that may be harmful to radio-communications if it is not
installed or used according to the instructions. Using this equipment in a specific installation may
generate harmful interferences, in which case the user may need to correct the interference using
one or all of the following methods:
• Redirect or move the receiver aerial
• Move the equipment away from the receiver
• Plug the equipment into a different socket from the one used for the receiver
• Contact the distributor or get help from a radio / TV technician.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• this device may not cause harmful interference.
• this device must accept any interference received, including interference that may cause
undesired operation.
This equipment complies with FCC’s radiation exposure limis set forth for an uncontrolled
environment under the following conditions:
• This equipment should be installed and operated such that a minimum separation distance of
20cm is maintained between the equipment and user’s/neraby person’s body at all times.
• This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the
party responsible fr compliance. Such modifications could void the user's authority to operate the
equipment.
Industry conformity Canada (IC)
This class B digital equipment complies with Canadian standard NMB- 03.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions :
• this device may not cause interference.
• this device must accept any interference, including interference that may cause undesired
operation.
Labguard 3
13
RECEPT_QSG_EN-A
EC compliance
This class B numeric equipment complies with the relevant EC directives and standards listed in the
accompanying certificate(s). Class B equipment is equipment suitable for use in domestic
establishments and in establishments directly connected to a low voltage power supply network
which supplies buildings used for domestic purposes. Class B equipment shall meet class B limits.
Compliance statement
Via this statement, we
bioMérieux SA
69280 MARCY l’ÉTOILE- FRANCE
hereby declare that the product designated hereafter - as a result of its design and its type as well as
the model that we have put into circulation - meets the fundamental health and safety requirements
defined by the EC directive concerned.
This statement shall be rendered invalid by any modification not approved by us.
Machine designation:
Model and reference type:
Applicable EC directives:
Monitoring hardware
The technical documents were
written by:
Date / Manufacturer's signature:
• EC low voltage Directive (2006/95/EC)
• EC-ECM directive (2004/108/EC)
•
EN 61010-1 (Ed. 2010): 2010, EN 61326-1 (Ed. 2006): 2006, EN
301 489-3 (Ed. 2002 V1.4.1): 2002 V1.4.1 EN 300-220-2 V2.4.1
EN 62479: 2010
Mr Develon
(Authorized person for documentation)
13 June 2013
Signatory's position:
Instrument R & D Manager
Harmonized standards applied in
particular:
Labguard 3
14
RECEPT_QSG_EN-A
Intentionally left blank.
Intentionally left blank.
Intentionally left blank.
Intentionally left blank.
Intentionally left blank.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2013:12:24 10:56:30+01:00
Modify Date                     : 2013:12:24 10:56:30+01:00
Creator                         : AH XSL Formatter V6.0 MR8 for Windows : 6.0.9.10681 (2013/04/23 18:22JST)
Producer                        : Antenna House PDF Output Library 6.0.396 (Windows)
Title                           : Quick start guide
Subject                         : RECEPT_QSG_EN-A
Trapped                         : False
Page Count                      : 20
Page Mode                       : UseOutlines
Language                        : EN

EXIF Metadata provided by EXIF.tools