BioSensics AP003 Active Personal Emergency Response System (ActivePERS) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2271939
Application ID	qzVQ8zd/+CiI5zwdzqlmfQ==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.17kB (352175 bits)
Date Submitted	2014-05-20 00:00:00
Date Available	2014-11-16 00:00:00
Creation Date	2014-04-30 10:01:14
Producing Software	Microsoft® Word 2013
Document Lastmod	2014-05-05 14:12:23
Document Title	User Manual.pdf
Document Creator	Microsoft® Word 2013
Document Author:	Ariane Callender

User Manual
ActivePERS (maker)
Active Personal Emergency Response System (product description)
Model Number: AP003
Introduction
ActivePERS is a personal emergency response pendant with patented and clinically
validated automatic fall detection algorithms developed by BioSensics LLC. The key
features and benefits of the ActivePERS technology include detecting falls with clinically
validated and patented algorithms that virtually eliminate false alarms, monitoring the
number of steps taken, and notifying providers when the pendant is not worn by the
subscriber.
This manual describes basic features of ActivePERS AP003.
Detecting a Fall
In the case of a fall detected automatically, the LED will turn on, and a fall alert
message will be transmitted.
Sending Heartbeat Messages
AP003 sends heartbeat messages every 15 minutes. These messages contain the
accumulated activity information, with values determined by the number of steps.
Sending Panic Signal
To send a panic signal, press and release the button. The LED should turn on upon
release, and a message will be transmitted to indicate the panic.
Clearing Alarm
To clear an alarm and turn off the LED, press and hold the button until the LED turns
off, which will take approximately 10 seconds. This will transmit a clear alarm message.
The LED will turn on and remain on after sending a fall or a panic signal. Sending a
clear alarm signal will turn the LED off.
Specifications







Dimension: 2.165” x 1.468” x 0.603”
RF Transmission Frequency: 2.4 GHz
Operating Temperature: -10ºC to 60ºC
Battery Type: CR2450 Lithium
Battery Life: 1 year
Battery Voltage: 3.0V
FCC ID: 2AA5H-AP003
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
NOTE: Changes or modifications not expressly approved by BioSensics, LLC could
void the user’s authority to operate this equipment.
Battery Warning
This product contains a lithium battery. Lithium batteries can explode, leak, catch fire or
cause burns if not handled appropriately. Do not disassemble, puncture or crush
battery. Avoid exposure to water, fire or high temperatures. Properly dispose of battery.
Radiation Exposure Statement
The product complies with the FCC portable RF exposure limit set forth for an
uncontrolled environment and is safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power if such
function is available.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2014:04:30 10:01:14-04:00
Creator Tool                    : Microsoft® Word 2013
Modify Date                     : 2014:05:05 14:12:23+08:00
Metadata Date                   : 2014:05:05 14:12:23+08:00
Format                          : application/pdf
Creator                         : Ariane Callender
Producer                        : Microsoft® Word 2013
Document ID                     : uuid:b57569cb-a490-4d51-a900-2da974348e99
Instance ID                     : uuid:bc88a4ac-5e21-448e-bbca-cff591a4ec18
Page Count                      : 3
Language                        : en-US
Author                          : Ariane Callender

EXIF Metadata provided by EXIF.tools