Biostar G41D3 Plus Owners Manual IG41M M7S & IG41N M7S_110427
2014-07-31
: Biostar Biostar-G41D3-Plus-Owners-Manual biostar-g41d3-plus-owners-manual biostar pdf
Open the PDF directly: View PDF .
Page Count: 47
Download | |
Open PDF In Browser | View PDF |
G41D3+/G41D3G+ Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing. The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies. Table of Contents Chapter 1: Introduction ............................................................ 1 1.1 Before You Start ................................................................................ 1 1.2 Package Checklist ............................................................................. 1 1.3 Motherboard Features...................................................................... 2 1.4 1.5 Rear Panel Connectors ..................................................................... 3 Motherboard Layout......................................................................... 4 Chapter 2: Hardware Installation ............................................. 5 2.1 Installing Central Processing Unit (CPU)....................................... 6 2.2 FAN Headers...................................................................................... 8 2.3 Installing System Memory ................................................................ 9 2.4 Connectors and Slots ....................................................................... 11 Chapter 3: Headers & Jumpers Setup ..................................... 13 3.1 How to Setup Jumpers .................................................................... 13 3.2 Detail Settings.................................................................................. 13 Chapter 4: Useful Help ............................................................ 19 4.1 Driver Installation Note.................................................................. 19 4.2 Software............................................................................................ 20 4.3 Extra Information............................................................................ 24 4.4 AMI BIOS Beep Code....................................................................... 26 4.5 Troubleshooting............................................................................... 27 Appendix: SPEC In Other Languages ...................................... 28 German.................................................................................................................. 28 French .................................................................................................................... 30 Italian..................................................................................................................... 32 Spanish ................................................................................................................... 34 Portuguese ............................................................................................................ 36 Polish...................................................................................................................... 38 Russian ................................................................................................................... 40 Arabic..................................................................................................................... 42 Japanese ................................................................................................................ 44 G41D3+/G41D3G+ CHAPTER 1: INTRODUCTION 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation. Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. Keep the computer from dangerous area, such as heat source, humid air and water. 1.2 PACKAGE CHECKLIST HDD Cable X 1 (optional) Serial ATA Cable X 2 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Setup Driver CD X 1 (full version manual files inside) FDD Cable X 1 (optional) USB 2.0 Cable X1 (optional) Serial ATA Power Cable X 1 (optional) Note: The package contents may be different due to area or your motherboard version. 1 Motherboard Manual 1.3 MOTHERBOARD FEATURES SPEC LGA 775 Supports Hyper-Threading / Execute Disable Bit / Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx processor Chipset Support 533 (For G41D3+ V6.1/6.2) / 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 ITE 8721 Super I/O Environment Control initiatives, Provides the most commonly used legacy Hardware Monitor Controller Super I/O functionality. Fan Speed Controller Low Pin Count Interface ITE's "Smart Guardian" function DIMM Slots x 2 Dual Channel Mode DDR3 memory module Main Each DIMM supports 256MB / 512MB / Supports DDR3 800/1066/1333(OC) Memory 1GB / 2GB / 4GB DDR3 Registered DIMM and ECC DIMM is not supported Max Memory Capacity 8GB (CPU with FSB 800 MHz only supports DDR3 800) Graphics GMA X4500 IDE Integrated IDE Controller SATA 2 Integrated Serial ATA Controller LAN Max Shared Video Memory is 1984MB (Depending on OS and memory size) Ultra DMA 33 / 66 / 100 Bus Master Mode supports PIO Mode 0~4 Data transfer rates up to 3.0 Gb/s. SATA Version 2.0 specification compliant Realtek RTL 8103EL (G41D3+ V6.0/6.1) 10 / 100 Mb/s auto negotiation Realtek RTL 8105T (G41D3+ V6.2) 10 / 100 Mb/s auto negotiation Realtek RTL 8111DL (G41D3G+ V6.0/6.1) 10 / 100 Mb/s / 1Gb/s auto negotiation Realtek RTL 8111E (G41D3G+ V6.2) 10 / 100 Mb/s / 1Gb/s auto negotiation Sound ALC662 (G41D3+/G41D3G+ V6.0/6.1) 5.1 channels audio out Codec VT1708B (G41D3+/G41D3G+ V6.2) High Definition Audio PCI slot x2 Supports PCI expansion cards PCI Express x 16 slot x1 Supports PCI-E x16 expansion cards Slots On Board Floppy Connector Connectors (G41D3+/G41D3G+ V6.0/6.1) Printer Port Connector 2 Extended Memory 64 Technology / Virtualization Technology (Maximum Watt: 95W) FSB Enhanced Intel SpeedStep® / Intel Architecture-64 / x1 x1 Each connector supports 2 Floppy drives Each connector supports 1 Printer port G41D3+/G41D3G+ SPEC Serial Port Connector x1 Connects to RS-232 Port IDE Connector x1 Each connector supports 2 IDE device SATA Connector x4 Each connector supports 1 SATA device Front Panel Connector x1 Supports front panel facilities Front Audio Connector x1 Supports front panel audio function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x1 System Fan Power supply Clear CMOS Header x1 Restore CMOS data to factory default USB Connector x2 Each connector supports 2 front panel USB ports Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply PS/2 Keyboard x1 Connects to PS/2 Keyboard PS/2 Mouse x1 Connects to PS/2 Mouse Back Panel VGA port x1 Connect to D-SUB monitor LAN port x1 Connect to RJ-45 ethernet cable USB Port x4 Connect to USB devices Audio Jack x3 Provide Audio-In/Out and microphone connection I/O Board Size 182 (W) x 235 (L) mm Biostar reserves the right to add or remove support for OS Support Windows 2000 / XP / Vista / 7 1.4 any OS with or without notice REAR PANEL CONNECTORS PS/2 Mouse LAN Line In/ Surround Line Out Mic In 1/ Bass/ Center PS/2 Keyboard VGA USBX2 USBX2 Since the audio chip supports High Definition Audio Specification, the function of each audio jack can be defined by software. The input / output function of each audio jack listed above represents the default setting. However, when connecting external microphone to the audio port, please use the Line In (blue) and Mic In (Pink) audio jack. 3 Motherboard Manual 1.5 MOTHERBOARD LAYOUT (G41D3+/G41D3G+ V6.0/6.1) KBMS1 LGA775 ATXPWR1 ATXPWR2 CPU _FAN1 Intel G41 JUSBV1 IDE1 USB1 DDR3_B1 VGA1 DDR3_A1 CPU1 RJ45USB1 BIOS AU DIO1 BAT TERY F_AUDIO1 PEX16_1 LAN PCI1 SATA4 Super I/O F_USB1 PCI2 J_COM1 J_PRIN T1 SYS_FAN1 Codec F_USB2 JUSBV2 SATA3 FDD1 PAN EL1 Note: ■ represents the 1st pin. 4 In tel IC H7 JCMOS1 SATA1 SATA2 G41D3+/G41D3G+ 1.6 MOTHERBOARD LAYOUT (G41D3+/G41D3G+ V6.2) KBMS1 LGA775 ATXPWR1 CPU1 C PU_FAN1 Intel G41 JUSBV1 IDE1 USB1 DDR3_B1 VGA1 DDR3_A1 ATXPWR2 RJ 45USB1 BIOS AU DIO1 F_AUDIO1 PEX16_1 LAN PCI1 SATA4 Super I/O F_USB1 PCI2 J_COM1 Codec BAT1 JCMOS1 F_USB2 SYS_FAN1 J_PRINT1 Inte l ICH7 JUSBV2 PANEL1 SATA3 SATA1 SATA2 Note: ■ represents the 1st pin. 5 Motherboard Manual CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Pin-Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle. 6 G41D3+/G41D3G+ Step 2: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 2-1: Step 2-2: Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1. This completes the installation. 7 Motherboard Manual 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different due to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. CPU_FAN1: CPU Fan Header 1 4 Pin 1 2 3 4 Assignment Ground Power FAN RPM rate sense Smart Fan Control Pin 1 2 3 Assignment Ground +12V FAN RPM rate sense SYS_FAN1: System Fan Header 3 1 Note: CPU_FAN1 supports 4-pin head connector; SYS_FAN1, 3-pin head one. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND. 8 G41D3+/G41D3G+ 2.3 INSTALLING SYSTEM MEMORY DDR3_B1 DDR3_A1 A. DDR3 module 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. 9 Motherboard Manual B. Memory Capacity DIMM Socket Location DDR3 Module DDR3_A1 256MB/512MB/1GB/2GB/4GB DDR3_B1 256MB/512MB/1GB/2GB/4GB Total Memory Size Max is 8GB. C. Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DDR3_A1 DDR3_B1 Disabled O X Disabled X O Enabled O O (O means memory installed; X, not installed.) The DRAM bus width of the memory module must be the same(x8 or x16) 10 G41D3+/G41D3G+ 2.4 CONNECTORS AND SLOTS FDD1: Floppy Disk Connector (Only for G41D3+ V6.0/6.1) The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2 34 1 33 IDE1: Hard Disk Connector The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality. The IDE connector can connect a master and a slave drive, so you can connect up to two hard disk drives. 40 39 2 1 11 Motherboard Manual PEX16_1: PCI-Express x16 Slot - PCI-Express 1.0a compliant. Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. 2X bandwidth over the traditional PCI architecture. PEX16_1 PCI1/PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2 12 G41D3+/G41D3G+ CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened 3.2 Pin closed Pin1-2 closed DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions. PWR_LED On/Off - + - 9 1 ++ 16 8 RST SPK HLED Pin Assignment 1 +5V 2 N/A 3 N/A 4 Speaker 5 HDD LED (+) 6 HDD LED (-) 7 Ground 8 Reset control Function Speaker Connector Hard drive LED Reset button Pin Assignment 9 N/A 10 N/A 11 N/A 12 Power LED (+) 13 Power LED (+) 14 Power LED (-) 15 Power button 16 Ground Function N/A N/A Power LED Power-on button 13 Motherboard Manual ATXPWR1: ATX Power Source Connector This connector allows user to connect 24-pin power connector on the ATX power supply. Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground 12 24 1 13 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V ATXPWR2: ATX Power Source Connector This connector provides +12V to CPU power circuit. 2 1 3 4 Pin 1 2 3 4 Assignment +12V +12V Ground Ground Note: Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in. 14 G41D3+/G41D3G+ F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel This motherboard provides 2 USB 2.0 headers, which allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. F_USB1 F_USB2 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC F_AUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. 10 9 2 1 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense 15 Motherboard Manual JCMOS1: Clear CMOS Header Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (Default). 1 3 1 Pin 2-3 Close: Clear CMOS data. 3 ※ Clear CMOS Procedures: 1. 2. 3. 4. 5. Remove AC power line. Set the jumper to “Pin 2-3 close”. Wait for five seconds. Set the jumper to “Pin 1-2 close”. Power on the AC. 6. Reset your desired password or clear the CMOS data. SATA1~SATA4: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 4channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s. SATA4 SATA3 SATA1 SATA2 1 16 4 7 Pin 1 2 3 4 5 6 7 Assignment Ground TX+ TXGround RXRX+ Ground G41D3+/G41D3G+ JUSBV1/JUSBV2: Power Source Headers for USB Ports Pin 1-2 Close: JUSBV1: +5V for USB ports at USB1/RJ45USB1. JUSBV2: +5V for USB ports at F_USB1/F_USB2. Pin 2-3 Close: JUSBV1: +5V STB for USB ports at USB1/RJ45USB1. JUSBV2: +5V STB for USB ports at F_USB1/F_USB2. 1 3 Pin 1-2 close JUSB V1 1 3 1 3 Pin 2-3 close JUS BV 2 J_COM1: Serial port Connector The motherboard has a Serial Port Connector for connecting RS-232 Port. 2 10 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Carrier detect Received data Transmitted data Data terminal ready Signal ground Data set ready Request to send Clear to send Ring indicator Key 17 Motherboard Manual J_PRINT1: Printer Port Connector This header allows you to connector printer on the PC. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 18 Assignment -Strobe -ALF Data 0 -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5 2 26 1 25 Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 Assignment Ground Data 6 Ground Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key G41D3+/G41D3G+ CHAPTER 4: USEFUL HELP 4.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program. B. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html 19 Motherboard Manual 4.2 SOFTWARE Installing Software 1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility. eHot-Line (Optional) eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem. Before you use this utility, please set Outlook Express as your default e-mail client application program. represents important *informa ti on that you must provide. Wi thout this information, you may not be able to send out the mail. This bl ock will show the i nformation which would be collected in the mail . conditi on *Describe of your system. your area or *Select the area cl ose to you. Provide the e-ma il address that you would like to send the copy to. e the name of *Provid the memory module manufacturer. Provide the name of the power suppl y manufacturer and the model no. Send the mail out. Exi t thi s dialog. Save these in forma tion to a .txt file 20 G41D3+/G41D3G+ After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail. We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service. If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following web http://www.biostar.com.tw/app/en-us/about/contact.php for getting our contact information. 21 Motherboard Manual BIOS Update BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system. AWARD BIOS Show current BIOS information Clear CMOS function (Only for AWARD BIOS) Save current BIOS to a .bin file Update BIOS with a BIOS fileOnce click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.) Then click Save. 22 AMI BIOS G41D3+/G41D3G+ Before doing this, please download the proper BIOS file from the website. For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure. After the BIOS Backup procedure, the open dialog will show for requesting the BIOS file which is going to be updated. Please choose the proper BIOS file for updating, then click on Open. The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process. After the BIOS Update process, click on OK to restart the system. While the system boots up and the full screen logo shows, press key to enter BIOS setup. In the BIOS setup, use the Load Optimized Defaults function and then Save and Exit Setup to exit BIOS setup. BIOS Update is completed. All the information and content above about the software are subject to be changed without notice. For better performance, the software is being continuously updated. The information and pictures described above are for your reference only. The actual information and settings on board may be slightly different from this manual. 23 Motherboard Manual 4.3 EXTRA INFORMATION CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section) 2. Wait for seconds. 3. Power on the system again. 24 G41D3+/G41D3G+ BIO-Flasher BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive or floppy disk. The BIO-Flasher is built in the BIOS chip. To enter the utility, press during the Power-On Self Tests (POST) procedure while booting up. Updating BIOS with BIO-Flasher 1. Go to the website to download the latest BIOS file for the motherboard. 2. Then, save the BIOS file into a USB pen drive or a floppy disk. 3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the USB port or the floppy disk drive. 4. Power on or reset the computer and then press during the POST process. A select dialog as the picture on the right appears. Select the device contains the BIOS file and press to enter the utility. 5. The utility will show the BIOS files and their respective information. Select the proper BIOS file and press then to perform the BIOS update process. 6. After the update process, the utility will ask you to reboot the system. Press to proceed. BIOS update completes. z z This utility only allows storage device with FAT32/16 format and single partition. Shutting down or resetting the system while updating the BIOS will lead to system boot failure. 25 Motherboard Manual 4.4 AMI BIOS BEEP CODE Boot Block Beep Codes Number of Beeps 1 2 3 4 5 7 10 11 12 13 Description No media present. (Insert diskette in floppy drive A:) “AMIBOOT.ROM” file not found in root directory of diskette in A: Insert next diskette if multiple diskettes are used for recovery Flash Programming successful File read error No Flash EPROM detected Flash Erase error Flash Program error “AMIBOOT.ROM” file size error BIOS ROM image mismatch (file layout does not match image present in flash device) POST BIOS Beep Codes Number of Beeps 1 3 6 7 8 Description Memory refresh timer error Base memory read/write test error Keyboard controller BAT command failed General exception error (processor exception interrupt error) Display memory error (system video adapter) Troubleshooting POST BIOS Beep Codes Number of Beeps 1, 3 6, 7 8 26 Troubleshooting Action Reseat the memory, or replace with known good modules. Fatal error indicating a serious problem with the system. Consult your system manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter. z If beep codes are generated when all other expansion cards are absent, consult your system manufacturer’s technical support. z If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card. If the system video adapter is an add-in card, replace or reseat the video adapter. If the video adapter is an integrated part of the system board, the board may be faulty. G41D3+/G41D3G+ 4.5 TROUBLESHOOTING Probable 1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive. Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. 1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. System only boots from an optical 1. Back up data and applications drive. Hard disks can be read, files. applications can be used, but system 2. Reformat the hard drive. fails to boot from a hard disk. Re-install applications and data using backup disks. Screen message shows “Invalid Review system’s equipment. Make sure Configuration” or “CMOS Failure.” correct information is in setup. System cannot boot after user installs a 1. Set master/slave jumpers second hard drive. correctly. 2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives. 27 Motherboard Manual APPENDIX: SPEC IN OTHER LANGUAGES GERMAN Spezifikationen LGA 775 Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Prozessoren (Maximales Watt: 95W) FSB Chipsatz Technology Intel G41 Intel ICH7 Umgebungskontrolle, Bietet die häufig verwendeten alten Super Hardware-Überwachung E/A-Funktionen. Lüfterdrehzahl-Controller/-Überwachung Low Pin Count-Schnittstelle "Smart Guardian"-Funktion von ITE Arbeitsspeich Jeder DIMM unterstützt 256MB / 512MB / 1GB / 2GB / 4GB DDR3. Max. 8GB Arbeitsspeicher Grafik GMA X4500 IDE Integrierter IDE-Controller SATA Integrierter Serial ATA-Controller LAN Extended Memory 64 Technology / Virtualization 1333 MHz DDR3 DIMM-Steckplätze x 2 er Enhanced Intel SpeedStep® / Intel Architecture-64 / 533 (Für G41D3+ V6.1/6.2) / 800 / 1066 / ITE 8721 Super E/A Unterstützt Hyper-Threading / Execute Disable Bit / Dual-Kanal DDR3 Speichermodul Unterstützt DDR3 800/1066/1333(OC) registrierte DIMMs. ECC DIMMs werden nicht unterstützt. (CPU mit 800 MHz FSB unterstützt nur DDR3-800) Max. 1984MB gemeinsam benutzter Videospeicher (Abhängig von OS und Speichergröße) Ultra DMA 33 / 66 / 100 Bus Master-Modus Unterstützt PIO-Modus 0~4, Datentransferrate bis zu 3.0Gb/s Konform mit der SATA-Spezifikation Version 2.0. Realtek RTL 8103EL (G41D3+ V6.0/6.1) 10 / 100 Mb/s Auto-Negotiation Realtek RTL 8105T (G41D3+ V6.2) 10 / 100 Mb/s Auto-Negotiation Realtek RTL 8111DL (G41D3G+ V6.0/6.1) 10 / 100 / 1000 Mb/s Auto-Negotiation Realtek RTL 8111E (G41D3G+ V6.2) 10 / 100 / 1000 Mb/s Auto-Negotiation ALC662 (G41D3+/G41D3G+ V6.0/6.1) Unterstützt High-Definition Audio VT1708B (G41D3+/G41D3G+ V6.2) 5.1-Kanal-Audioausgabe HD Audio-Unters tützung 28 G41D3+/G41D3G+ Spezifikationen Steckplätze PCI-Steckplatz x2 PCI Express x16 Steckplatz x1 Diskettenlaufwerkanschluss (G41D3+/G41D3G+ V6.0/6.1) x1 Druckeranschluss Anschluss x1 x1 IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen x1 Unterstützt die Fronttafel-Audioanschlussfunktion CPU-Lüfter-Sockel x1 System-Lüfter-Sockel x1 "CMOS löschen"-Sockel x1 USB-Anschluss x2 Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 PS/2-Tastatur x1 PS/2-Maus x1 Rückseiten-E VGA-Anschluss x1 LAN-Anschluss x1 USB-Anschluss x4 Audioanschluss x3 /A Jeder Anschluss unterstützt 1 Druckeranschluss Serieller Anschluss Onboard-Ans Front-Audioanschluss chluss Jeder Anschluss unterstützt 2 Diskettenlaufwerke CPU-Lüfterstromversorgungsanschluss (mit Smart Fan-Funktion) System-Lüfter-Stromversorgungsanschluss Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse Platinengröße 182 mm (B) X 235 mm (L) OS-Unterstüt zung Biostar behält sich das Recht vor, ohne Ankündigung Windows 2000 / XP / Vista / 7 die Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen. 29 Motherboard Manual FRENCH SPEC LGA 775 Processeurs Intel Core2Duo / Core2Quad UC / Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx (Watt maximum : 95W) Bus frontal Chipset Super E/S Prend en charge les technologies Hyper-Threading / d'exécution de bit de désactivation / Intel SpeedStep® optimisée/ d'architecture Intel 64 / de mémoire étendue 64 / de virtualisation 533 (Pour G41D3+ V6.1/6.2) / 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 ITE 8721 Initiatives de contrôle environnementales, Fournit la fonctionnalité de Super E/S Moniteur de matériel patrimoniales la plus utilisée. Contrôleur /moniteur de vitesse de ventilateur Interface à faible compte de broches Fonction "Gardien intelligent" de l'ITE Module de mémoire DDR3 à mode à double voie Fentes DDR3 DIMM x 2 Prend en charge la DDR3 800/1066/1333(OC) Mémoire Chaque DIMM prend en charge des DDR3 Les DIMM à registres et DIMM avec code correcteurs principale de 256Mo / 512Mo / 1Go / 2Go / 4Go d'erreurs ne sont pas prises en charge Capacité mémoire maximale de 8Go (UC avec FSB 800 MHz ne prend en charge que DDR3 800) Graphiques GMA X4500 IDE SATA LAN Prise en charge audio HD 30 Contrôleur IDE intégré Contrôleur Serial ATA intégré Mémoire vidéo partagée maximale de 1984 Mo (Selon la capacité d'OS et de mémoire) Mode principale de Bus Ultra DMA 33 / 66 / 100 Prend en charge le mode PIO 0~4, Taux de transfert jusqu'à 3.0Go/s. Conforme à la spécification SATA Version 2.0 Realtek RTL 8103EL (G41D3+ V6.0/6.1) 10 / 100 Mb/s négociation automatique Realtek RTL 8105T (G41D3+ V6.2) 10 / 100 Mb/s négociation automatique Realtek RTL 8111DL (G41D3G+ V6.0/6.1) 10 / 100 / 1000 Mb/s négociation automatique Realtek RTL 8111E (G41D3G+ V6.2) 10 / 100 / 1000 Mb/s négociation automatique ALC662 (G41D3+/G41D3G+ V6.0/6.1) Prise en charge de l'audio haute définition VT1708B (G41D3+/G41D3G+ V6.2) Sortie audio à 5.1 voies G41D3+/G41D3G+ SPEC Fentes Fente PCI x2 Fente PCI Express x16 x1 Connecteur de disquette Chaque connector prend en charge 2 lecteurs de (G41D3+/G41D3G+ V6.0/6.1) x1 disquettes Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante Port série x1 Connecteur IDE x1 Connecteur SATA x4 Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant embarqué Alimentation électrique du ventilateur UC (avec fonction Embase de ventilateur UC x1 Embase de ventilateur système x1 Embase d'effacement CMOS x1 Connecteur USB x2 Connecteur d'alimentation x1 Chaque connecteur prend en charge 2 périphériques IDE Chaque connecteur prend en charge 1 périphérique SATA de ventilateur intelligent) Alimentation électrique du ventilateur système Chaque connecteur prend en charge 2 ports USB de panneau avant (24 broches) Connecteur d'alimentation x1 (4 broches) Clavier PS/2 E/S du panneau arrière Dimensions de la carte x1 Souris PS/2 x1 Port VGA x1 Port LAN x1 Port USB x4 Fiche audio x3 182 mm (l) X 235 mm (H) Support SE Windows 2000 / XP / Vista / 7 Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis. 31 Motherboard Manual ITALIAN SPECIFICA LGA 775 Processore Intel Core2Duo / CPU Core2Quad / Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Supporto di Hyper-Threading / Execute Disable Bit / Enhanced Intel SpeedStep® / Architettura Intel 64 / Tecnologia Extended Memory 64 / Tecnologia V irtualization (Watt massimo: 95W) FSB 533 (Per G41D3+ V6.1/6.2) / 800 / 1066 / 1333 MHz Chipset Intel G41 Intel ICH7 ITE 8721 Super I/O Funzioni di controllo dell’ambiente: Fornisce le funzionalità legacy Super Monitoraggio hardware I/O usate più comunemente. Controller / Monitoraggio velocità ventolina Interfaccia LPC (Low Pin Count) Funzione "Smart Guardian" di ITE Alloggi DIMM DDR3 x 2 Modulo di memoria DDR3 a canale doppio Memoria Ciascun DIMM supporta DDR3 256MB Supporto di DDR3 800/1066/1333(OC) principale / 512MB / 1GB / 2GB / 4GB DIMM registrati e DIMM ECC non sono supportati Capacità massima della memoria 8GB (CPU con FSB a 800 MHz supporta solo DDR3 800) Grafica GMA X4500 La memoria video condivisa massima è di 1984MB (Secondo l'OS e la capacità di memoria) IDE Controller IDE integrato Modalità Bus Master Ultra DMA 33 / 66 / 100 Supporto modalità PIO Mode 0-4 SATA Controller Serial ATA integrato Velocità di trasferimento dei dati fino a 3.0Gb/s. Compatibile specifiche SATA Versione 2.0. LAN Realtek RTL 8103EL (G41D3+ V6.0/6.1) Negoziazione automatica 10 / 100 Mb/s Realtek RTL 8105T (G41D3+ V6.2) Negoziazione automatica 10 / 100 Mb/s Realtek RTL 8111DL (G41D3G+ V6.0/6.1) Negoziazione automatica 10 / 100 / 1000 Mb/s Realtek RTL 8111E (G41D3G+ V6.2) Negoziazione automatica 10 / 100 / 1000 Mb/s Supporto ALC662 (G41D3+/G41D3G+ V6.0/6.1) Supporto audio High-Definition (HD) audio HD VT1708B (G41D3+/G41D3G+ V6.2) Uscita audio 5.1 canali 32 G41D3+/G41D3G+ SPECIFICA Alloggi Alloggio PCI x2 Alloggio PCI Express x16 x1 Connettore floppy (G41D3+/G41D3G+ V6.0/6.1) x1 Connettori Ciascun connettore supporta 2 unità Floppy Connettore Porta stampante x1 Porta seriale x1 Connettore IDE x1 Ciascun connettore supporta 2 unità IDE Connettore SATA x4 Ciascun connettore supporta 1 unità SATA Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Collettore ventolina CPU x1 Collettore ventolina sistema x1 Collettore cancellaz ione CMOS x1 Connettore USB x2 Connettore alimentazione x1 su scheda Ciascun connettore supporta 1 Porta stampante Alimentazione ventolina CPU (con funzione Smart Fan) Alimentazione ventolina di sistema Ciascun connettore supporta 2 porte USB pannello frontale (24 pin) Connettore alimentazione x1 (4 pin) I/O pannello posteriore Tastiera PS/2 x1 Mouse PS/2 x1 Porta VGA x1 Porta LAN x1 Porta USB x4 Connettore audio x3 Dimension 182 mm (larghezza) x 235 mm i scheda (altezza) Sistemi operativi supportati Biostar si riserva il diritto di aggiungere o Windows 2000 / XP / Vista / 7 rimuovere il supporto di qualsiasi sistema operativo senza preavviso. 33 Motherboard Manual SPANISH Especificación LGA 775 Procesador Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Admite Hyper-Threading / Bit de deshabilitación de ejecución / Intel SpeedStep® Mejorado / Intel Architecture-64 / Tecnología Extended Memory 64 / Tecnología de virtualización (Vatio máximo: 95W) FSB 533 (Para G41D3+ V6.1/6.2) / 800 / 1066 / 1333 MHz Conjunto de Intel G41 chips Intel ICH7 ITE 8721 Súper E/S Iniciativas de control de entorno, Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S. Controlador/monitor de velocidad de ventilador Interfaz de cuenta Low Pin Función "Guardia inteligente" de ITE Ranuras DIMM DDR3 x 2 Módulo de memoria DDR3 de canal Doble Memoria Cada DIMM admite DDR de 256MB / Admite DDR3 de 800/1066/1333(OC) principal 512MB / 1GB / 2GB / 4GB No admite DIMM registrados o DIMM compatibles con Capacidad máxima de memoria de 8GB ECC (CPU con FSB de 800 MHz sólo soporta DDR3 800) Gráficos GMA X4500 Memoria máxima de vídeo compartida de 1984MB (Dependiendo de tamaño del OS y de la memoria) IDE Controlador IDE integrado Modo bus maestro Ultra DMA 33 / 66 / 100 Soporte los Modos PIO 0~4, SATA Controlador ATA Serie Integrado Tasas de transferencia de hasta 3.0 Gb/s. Compatible con la versión SATA 2.0. Red Local Realtek RTL 8103EL (G41D3+ V6.0/6.1) Negociación de 10 / 100 Mb/s Realtek RTL 8105T (G41D3+ V6.2) Negociación de 10 / 100 Mb/s Realtek RTL 8111DL (G41D3G+ V6.0/6.1) Negociación de 10 / 100 / 1000 Mb/s Realtek RTL 8111E (G41D3G+ V6.2) Negociación de 10 / 100 / 1000 Mb/s Soporte de ALC662 (G41D3+/G41D3G+ V6.0/6.1) Soporte de sonido de Alta Definición sonido HD Salida de sonido de 5.1 canales 34 VT1708B (G41D3+/G41D3G+ V6.2) G41D3+/G41D3G+ Especificación Ranuras Ranura PCI X2 Ranura PCI Express x16 X1 Conector disco flexible Conectores en placa Cada conector soporta 2 unidades de disco flexible (G41D3+/G41D3G+ V6.0/6.1) X1 Conector Puerto de impresora X1 Puerto serie X1 Conector IDE X1 Cada conector soporta 2 dispositivos IDE Conector SATA X4 Cada conector soporta 1 dispositivos SATA Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con Cada conector soporta 1 Puerto de impresora función Smart Fan) Cabecera de ventilador de sistema X1 Cabecera de borrado de CMOS X1 Conector USB X2 Conector de alimentación X1 Fuente de alimentación de ventilador de sistema Cada conector soporta 2 puertos USB frontales (24 patillas) Conector de alimentación X1 (4 patillas) Panel trasero de E/S Tamaño de Teclado PS/2 X1 Ratón PS/2 X1 Puerto VGA X1 Puerto de red local X1 Puerto USB X4 Conector de sonido X3 182 mm. (A) X 235 Mm. (H) la placa Soporte de sistema Biostar se reserva el derecho de añadir o retirar el Windows 2000 / XP / Vista / 7 soporte de cualquier SO con o sin aviso previo. operativo 35 Motherboard Manual PORTUGUESE ESPECIFICAÇÕES LGA 775 Processador Intel Core2Duo / Core2Quad Suporta as tecnologias Hyper-Threading / Execute CPU / Pentium Dual-Core / Celeron Dual-Core / Disable Bit / Enhanced Intel SpeedStep® / Intel Celeron 4xx Arquitecture -64 / Extended Memory 64 / Virtualization (Watt máximo: 95W) FSB Chipset 533 (Para G41D3+ V6.1/6.2) / 800 / 1066 / 1333 MHz Intel G41 Intel ICH7 ITE 8721 Especificaçã o Super I/O Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O. Interface LPC (Low Pin Count). Memória principal Placa gráfica Monitorização do hardware Controlador/Monitor da velocidade da ventoinha Função "Smart Guardian" da ITE Ranhuras DIMM DDR3 x 2 Módulo de memória DDR3 de canal duplo Cada módulo DIMM suporta uma Suporta módulos DDR3 800/1066/1333(OC) memória DDR3 de 256 MB / 512 MB / 1GB Os módulos DIMM registados e os DIMM ECC não são / 2GB / 4GB suportados Capacidade máxima de memória: 8GB (CPU com FSB 800 MHz só suporta DDR3 800) GMA X4500 IDE Controlador IDE integrado SATA Controlador Serial ATA integrado LAN Iniciativas para controlo do ambiente Memória de vídeo máxima partilhada: 1984 MB (Dependendo do tamanho do ósmio e de memória) Modo Bus master Ultra DMA 33 / 66 / 100 Suporta o modo PIO 0~4, Velocidades de transmissão de dados até 3.0 Gb/s. Compatibilidade com a especificação SATA versão 2.0. Realtek RTL 8103EL (G41D3+ V6.0/6.1) Auto negociação de 10 / 100 Mb/s Realtek RTL 8105T (G41D3+ V6.2) Auto negociação de 10 / 100 Mb/s Realtek RTL 8111DL (G41D3G+ V6.0/6.1) Auto negociação de 10 / 100 / 1000 Mb/s Realtek RTL 8111E (G41D3G+ V6.2) Auto negociação de 10 / 100 / 1000 Mb/s para áudio ALC662 (G41D3+/G41D3G+ V6.0/6.1) Suporta a especificação High-Definition Audio de alta VT1708B (G41D3+/G41D3G+ V6.2) Saída de áudio de 5.1 canais Suporte definição 36 G41D3+/G41D3G+ ESPECIFICAÇÕES Ranhuras Ranhura PCI x2 Ranhura PCI Express x16 x1 Conector da unidade de disquetes (G41D3+/G41D3G+ V6.0/6.1) x1 Conector da para impressora x1 Cada conector suporta 1 Porta para impressora Porta série x1 Conector IDE x1 Cada conector suporta 2 dispositivos IDE Conector SATA x4 Cada conector suporta 1 dispositivo SATA Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Conectores Conector da ventoinha da CPU na placa Cada conector suporta 2 unidades de disquetes x1 Conector da ventoinha do sistema x1 Conector para limpeza do CMOS x1 Conector USB x2 Conector de alimentação x1 Suporta a função de áudio no painel frontal Alimentação da ventoinha da CPU (com a função Smart Fan) Alimentação da ventoinha do sistema Cada conector suporta 2 portas USB no painel frontal (24 pinos) Conector de alimentação x1 (4 pinos) Teclado PS/2 x1 Entradas/S Rato PS/2 x1 aídas no Porta VGA x1 painel Porta LAN x1 traseiro Porta USB x4 Tomada de áudio x3 Tamanho da placa 182 mm (L) X 235 mm (A) Sistemas operativos suportados A Biostar reserva-se o direito de adicionar ou remover Windows 2000 / XP / Vista / 7 suporte para qualquer sistema operativo com ou sem aviso prévio. 37 Motherboard Manual POLISH SPEC LGA 775 Procesor Intel Core2Duo / Core2Quad / Procesor Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Obsługa Hyper-Threading / Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology (Maksymalny Watt: 95W) FSB 533 (Na G41D3+ V6.2) / 800 / 1066 / 1333 MHz Chipset Intel G41 Intel ICH7 Gniazda DDR3 DIMM x 2 Moduł pamięci DDR3 z trybem podwójnego kanału Pamięć Każde gniazdo DIMM obsługuje moduły Obsługa DDR3 800/1066/1333(OC) główna 256MB / 512MB / 1GB / 2GB / 4GB Brak obsługi Registered DIMM oraz ECC DIMM Maks. wielkość pamięci 8GB (CPU z FSB 800 MHz tylko obsługuje pamięci DDR3 800) Grafika GMA X4500 Maks. wielkość współdzielonej pamięci video wynosi 1984MB (W zależności od wielkości pamięci i OS) ITE 8721 Super I/O IDE Funkcje kontroli warunków pracy, Zapewnia najbardziej powszechne funkcje Monitor H/W Super I/O. Kontroler/Monitor prędkości wentylatora Interfejs Low Pin Count Funkcja ITE "Smart Guardian" Zintegrowany kontroler IDE Ultra DMA 33 / 66 / 100 Tryb Bus Master obsługa PIO tryb 0~4, SATA Zintegrowany kontroler Serial ATA Transfer danych do 3.0 Gb/s. Zgodność ze specyfikacją SATA w wersji 2.0. LAN Realtek RTL 8103EL (G41D3+ V6.0/6.1) 10 / 100 Mb/s z automatyczną negocjacją szybkości Realtek RTL 8105T (G41D3+ V6.2) 10 / 100 Mb/s z automatyczną negocjacją szybkości Realtek RTL 8111DL (G41D3G+ V6.0/6.1) 10 / 100 / 1000 Mb/s z automatyczną negocjacją Realtek RTL 8111E (G41D3G+ V6.2) szybkości Obsługa ALC662 (G41D3+/G41D3G+ V6.0/6.1) Obsługa High-Definition Audio audio HD VT1708B (G41D3+/G41D3G+ V6.2) 5.1 kanałowe wyjście audio 38 G41D3+/G41D3G+ SPEC Gniazda Gniazdo PCI x2 Gniazdo PCI Express x16 x1 Złącze napędu dyskietek Złącza wbudowane Każde złącze obsługuje 2 napędy dyskietek (G41D3+/G41D3G+ V6.0/6.1) x1 Złącze Port drukarki x1 Port szeregowy x1 Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA Złącze panela przedniego x1 Obsługa elementów panela przedniego Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze główkowe wentylatora procesora x1 Złącze główkowe wentylatora systemowego x1 Każde złącze obsługuje 1 Port drukarki Zasilanie wentylatora procesora (z funkcją Smart Fan) Zasilanie wentylatora systemowego Złącze główkowe kasowania CMOS x1 Złącze USB x2 Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Klawiatura PS/2 x1 Mysz PS/2 x1 Back Panel Port VGA x1 I/O Port LAN x1 Port USB x4 Gniazdo audio x3 Wymiary płyty operacyjne go przednim 182 mm (S) X 235 mm (W) Obsluga systemu Każde złącze obsługuje 2 porty USB na panelu Biostar zastrzega sobie prawo dodawania lub Windows 2000 / XP / Vista / 7 odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia. 39 Motherboard Manual RUSSIAN СПЕЦ CPU (центральн ый процессор) FSB Набор LGA 775 Процессор Intel Core2Duo / Core2Quad / Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx (Максимальный ватт: 95W) Поддержка технологий Hyper-Threading / Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / технологии виртуализация 533 (Для G41D3+ V6.1/6.2) / 800 / 1066 / 1333 МГц Intel G41 микросхем Intel ICH7 Модуль памяти с двухканальным режимом DDR3 Слоты DDR3 DIMM x 2 Поддержка DDR3 800/1066/1333(OC) Основная Каждый модуль DIMM поддерживает Не поддерживает зарегистрированные модули память 256 МБ / 512МБ / 1ГБ / 2ГБ / 4ГБ DDR3 DIMM and ECC DIMM Максимальная ёмкость памяти 8ГБ (Процессор с ФСБ 800 МГц поддерживает только DDR3 800) Максимальная совместно используемая видео Графика GMA X4500 память составляет 1984 МБ (В зависимости от осмия и размера запоминающего устройства) ITE 8721 Обеспечивает наиболее используемые Super I/O действующие функциональные возможности Super I/O. Интерфейс с низким количеством выводов IDE SATA Аппаратный монитор Регулятор скорости вентилятора/ монитор Функция ITE "Smart Guardian" (Интеллектуальная защита) Встроенное устройство управления Режим "хозяина" шины Ultra DMA 33 / 66 / 100 встроенными интерфейсами устройств Поддержка режима PIO 0~4, Встроенное последовательное скорость передачи данных до 3.0 гигабит/с. устройство управления ATA Соответствие спецификации SATA версия 2.0. Realtek RTL 8103EL (G41D3+ V6.0/6.1) Локальная Realtek RTL 8105T (G41D3+ V6.2) сеть Инициативы по охране окружающей среды, Автоматическое согласование 10 / 100 Мб/с Автоматическое согласование 10 / 100 Мб/с Realtek RTL 8111DL (G41D3G+ V6.0/6.1) Автоматическое согласование 10 / 100 / 1000 Мб/с Realtek RTL 8111E (G41D3G+ V6.2) Автоматическое согласование 10 / 100 / 1000 Мб/с Звуковая поддержка ALC662 (G41D3+/G41D3G+ V6.0/6.1) Звуковая поддержка High-Definition жесткого 5.1канальный звуковой выход диска 40 VT1708B (G41D3+/G41D3G+ V6.2) G41D3+/G41D3G+ СПЕЦ Слоты Слот PCI x2 Слот PCI Express x16 x1 Разъём НГМД (G41D3+/G41D3G+ V6.0/6.1) Каждый разъём поддерживает 2 накопителя на x1 Разъём Порт подключения Встроенны й разъём гибких магнитных дисках Каждый разъём поддерживает 1 Порт подключения принтера x1 Последовательный порт x1 Разъём IDE x1 Разъём SATA x4 Каждый разъём поддерживает 1 устройство SATA Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели принтера Каждый разъём поддерживает 2 встроенных интерфейса накопителей Источник питания для вентилятора центрального Контактирующее приспособление вентилятора центрального процессора процессора (с функцией интеллектуального вентилятора) x1 Контактирующее приспособление вентилятора системы x1 Источник питания для вентилятора системы Открытое контактирующее приспособление CMOS x1 USB-разъём x2 Разъем питания (24 вывод) x1 Разъем питания (4 вывод) x1 Клавиатура PS/2 x1 Задняя Мышь PS/2 x1 панель Порт VGA x1 средств Порт LAN x1 ввода-выв USB-порт x4 ода панели Поддержка OS лицевой панели Гнездо для подключения наушников Размер Каждый разъём поддерживает 2 USB-порта на x3 182 мм (Ш) X 235 мм (В) Biostar сохраняет за собой право добавлять или Windows 2000 / XP / Vista / 7 удалять средства обеспечения для OS с или без предварительного уведомления. 41 Motherboard Manual ARABIC اﻟﻤﻮاﺻﻔﺎت LGA 775 وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ Intel Core2Duo / Core2Quad /ﻣﻌﺎﻟﺠﺎت Pentium Dual-Core / Celeron Dual-Core / ﺑﺘﺮدد یﺼﻞ إﻟﻰ Celeron 4xx Hyper-Threading / Execute Disable Bit /ﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology )و: 95ﻗﺼ ﻮى واط( V6.1/6.2 G41D3+) / 800ﻟﻼﻃ ﻼع( 533ﺗﺮدد اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻥﺒﻲ ﻣﻴﺠﺎ هﺮﺗﺰ / 1066 / 1333 Intel G41 ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ Intel ICH7 ﻓﺘﺤﺔ DDR3 DIMM ﻋﺪد2 ﺳﻌﺔ ﺗﺪﻋﻢ آﻞ DDR3ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮع DIMMﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻣﺎت ﺳﻌﺎت 800/1066/(OC)1333ﻣﻴﺠﺎ ﺑﺎیﺖDDR3ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع ﻣﻴﺠﺎ ﺑﺎیﺖ /512ﺳﻌﺔ DDR3ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮع DIMMﻓﺘﺤﺔ ECCوﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊ DIMMﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة و /1و /2و 4ﺝﻴﺠﺎ ﺑﺎیﺖ ﺗ ﺪﻋﻢ ﻓﻘ ﻂ ﻣﻴﻐ ﺎهﻴﺮﺗﺰ اﻟﻤﺮآﺰی ﺔ اﻟﻤﻌﺎﻟﺠ ﺔ وﺣﺪة ﻣﻊ ﻣﻴﺠ ﺎهﺮﺗﺰ (800 ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى 8ﺝﻴﺠﺎ ﺑﺎیﺖ )DDR3 800 GMA X4500 ﻣﻴﺠﺎ ﺑﺎیﺖ1984أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪیﻮ اﻟﻤﺸﺘﺮآﺔ )اﻟ ﺬاآﺮة وﺣﺠﻢ اﻟﺘﺸ ITE 8721 Super I/O ﻣﺰدوﺝﺔ اﻟﻘﻨﺎةDDR3وﺣﺪة ذاآﺮة اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎSuper I/O .ﺗﻮﻓﺮ وﻇﻴﻔﺔ Low Pin Count Interfaceﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ ﻣﻨﻔﺬ IDE ﻣﺘﻜﺎﻣﻞIDEﻣﺘﺤﻜﻢ SATA ﻣﺘﻜﺎﻣﻞSerial ATAﻣﺘﺤﻜﻢ ﻐﻴﻞ ﻧﻈﺎم ﻋﻠ ﻰ اﻋﺘﻤ ﺎدا( وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ: ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ ITEﻣﻦ ""Smart Guardianوﻇﻴﻔﺔ وﺿﻊ رﺋﻴﺴﻲUltra DMA 33 / 66 / 100ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ PIO Mode 0~4دﻋﻢ وﺿﻊ ﺝﻴﺠﺎﺑﺖ/ﺙﺎﻥﻴﺔ3.0.ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ 2.0.اﻹﺹﺪار SATAﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت ) Realtek RTL 8103EL (G41D3+ V6.0/6.1ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 100/10ﻣﻴﺠﺎ ﺑﺎیﺖ /ﺙﺎﻥﻴﺔ )Realtek RTL 8105T (G41D3+ V6.2 ﺵﺒﻜﺔ داﺧﻠﻴﺔ ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 100/10ﻣﻴﺠﺎ ﺑﺎیﺖ /ﺙﺎﻥﻴﺔ ) Realtek RTL 8111DL (G41D3G+ V6.0/6.1ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 100/10ﻣﻴﺠﺎ ﺑﺎیﺖ /ﺛﺎﻧﻴﺔ و1ﺝﻴﺠﺎ ﺑﺖ/ﺛﺎﻧﻴﺔ )Realtek RTL 8111E (G41D3G+ V6.2 ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 100/10ﻣﻴﺠﺎ ﺑﺎیﺖ /ﺛﺎﻧﻴﺔ و1ﺝﻴﺠﺎ ﺑﺖ/ﺛﺎﻧﻴﺔ دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ )ALC662 (G41D3+/G41D3G+ V6.0/6.1 ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻣﻦ اﻟﺘﻌﺮیﻒ )VT1708B (G41D3+/G41D3G+ V6.2 5.1ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت 42 G41D3+/G41D3G+ اﻟﻤﻮاﺻﻔﺎت ﻓﺘﺤﺔ PCI اﻟﻔﺘﺤﺎت ﻋﺪد 2 ﻓﺘﺤﺔ PCI Express x16ﻋﺪد 1 ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻥﺔ ) (G41D3+/G41D3G+ V6.0/6.1ﻋﺪد 1 یﺪﻋﻢ ﻣﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد1 ﻣﻨﻔﺬ IDE ﻋﺪد 1 IDEیﺪﻋﻢ آﻞ ﻣﻨﻔﺬ اﺙﻨﻴﻦ ﻣﻦ أﺝﻬﺰة ﻣﻨﻔﺬ SATA ﻋﺪد 4 SATAیﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻋﺪد 1 یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ اﻟﻠﻮﺣﺔ ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ ﻋﺪد 1 یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 1 وﺹﻠﺔ ﻣﺴﺢ CMOS ﻋﺪد 1 ﻣﻨﻔﺬ USB ﻋﺪد 2 ﻋﺪد 1 Smart Fanﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔ ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔUSBیﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس( ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺑﺎﺑﻴﺲ( ﻋﺪد 1 ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ PS/2 ﻋﺪد 1 ﻣﺎوس PS/2 ﻋﺪد 1 ﻣﻨﺎﻓﺬ دﺧﻞ/ﺧﺮج ﻣﻨﻔﺬ VGA ﻋﺪد 1 اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ ﻋﺪد 1 ﻣﻨﺎﻓﺬ USB ﻋﺪد 4 ﻣﻘﺒﺲ ﺹﻮت ﻋﺪد 3 ﺣﺠﻢ اﻟﻠﻮﺣﺔ 182ﻣﻢ )ﻋﺮض( 235 Xﻣﻢ )ارﺗﻔﺎع( دﻋﻢ أﻧﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ Windows 2000 / XP / Vista / 7 43 ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻧﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺧﻄﺎر أو ﺑﺪون Biostarﺗﺤﺘﻔﻆ إﺧﻄﺎر. Motherboard Manual JAPANESE 仕様 LGA 775 Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx processor (最高のワット: 95W) FSB Hyper-Threading / Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technologyをサ ポートします 533 (G41D3 + V6.1/6.2の場合) / 800 / 1066 / 1333 MHz Intel G41 チップセット Intel ICH7 DDR3 DIMMスロット x 2 各DIMMは 256MB / 512MB / 1GB / 2GB / メインメモリ 4GB DDR3をサポート デュアル チャンネルモードDDR3メモリモジュール DDR3 800/1066/1333(OC)をサポート 登録済みDIMMとECC DIMMはサポートされません (のCPUのFSBを800 MHzの唯一のDDR3 800をサポートし 最大メモリ容量8GB ています) グラフィック GMA X4500 (OSとメモリのサイズにより異なります) ス ITE 8721 Super I/O 環境コントロールイニシアチブ、 もっとも一般に使用されるレガシーSuper I/O H/Wモニター 機能を採用しています。 ファン速度コントローラ/ モニター 低ピンカウントインターフェイス ITEの「スマートガーディアン」機能 Ultra DMA 33 / 66 / 100バスマスタモード IDE 統合IDEコントローラ SATA 統合シリアルATAコントローラ LAN 最大の共有ビデオメモリは1984MBです PIO Mode 0~4のサポート、 最高3.0 Gb/秒のデータ転送速度 SATAバージョン2.0仕様に準拠。 Realtek RTL 8103EL (G41D3+ V6.0/6.1) 10 / 100 Mb/秒のオートネゴシエーション Realtek RTL 8105T (G41D3+ V6.2) 10 / 100 Mb/秒のオートネゴシエーション Realtek RTL 8111DL (G41D3G+ V6.0/6.1) 10 / 100 / 1000 Mb/秒のオートネゴシエーション Realtek RTL 8111E (G41D3G+ V6.2) 10 / 100 / 1000 Mb/秒のオートネゴシエーション HDオーディ ALC662 (G41D3+/G41D3G+ V6.0/6.1) ハイデフィニションオーディオのサポート オのサポート VT1708B (G41D3+/G41D3G+ V6.2) 5.1 チャンネルオーディオアウト 44 G41D3+/G41D3G+ 仕様 スロット PCIスロット x2 PCI Express x16スロット x1 フロッピーコネクタ x1 プリンタポートコネクタ x1 シリアルポート x1 IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします フロントパネルコネクタ x1 フロントパネル機能をサポートします フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載) システムファンヘッダ x1 システムファン電源装置 CMOSクリアヘッダ x1 USBコネクタ x2 オンボードコ ネクタ 各コネクタは2つのフロッピードライブをサポートします (G41D3+/G41D3G+ V6.0/6.1) 各コネクタは1つのプリンタポートをサポートします 各コネクタは2つのフロントパネルUSBポートをサポートし ます 電源コネクタ(24ピン) x1 電源コネクタ(4ピン) x1 PS/2キーボード x1 PS/2マウス x1 背面パネル VGAポート x1 I/O LANポート x1 USBポート x4 オーディオジャック x3 ボードサイズ 182 mm (幅) X 235 mm (高さ) OSサポート Windows 2000 / XP / Vista / 7 Biostarは事前のサポートなしにOSサポートを追加または削 除する権利を留保します。 2011/04/27 45
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2011:04:27 18:10:26+08:00 Modify Date : 2011:04:27 18:10:26+08:00 Page Count : 47 Creation Date : 2011:04:27 10:10:26Z Mod Date : 2011:04:27 10:10:26Z Producer : Acrobat Distiller 5.0 (Windows) Author : 97031 Metadata Date : 2011:04:27 10:10:26Z Creator : 97031 Title : Microsoft Word - IG41M-M7S & IG41N-M7S_110427.docEXIF Metadata provided by EXIF.tools