Biostar P4M800 M7 Owners Manual P4M80M7&M7A_V80_0227C

2014-07-31

: Biostar Biostar-P4M800-M7-Owners-Manual biostar-p4m800-m7-owners-manual biostar pdf

Open the PDF directly: View PDF .
Page Count: 67

Download
Open PDF In Browser	View PDF

P4M80-M7 & P4M80-M7A

FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents
Chapter 1: Introduction ...............................................................1
1.1

Features ..............................................................................................1

1.2

Package List .......................................................................................3

1.3

Layout: P4M80-M7............................................................................4

1.4

Components: P4M80-M7 .................................................................5

1.5

Layout: P4M80-M7A (Rev 1.0) ........................................................6

1.6

Components: P4M80-M7A (Rev 1.0) ..............................................7

1.7

Layout: P4M80-M7A (Rev 7.0 & 8.0) ..............................................8

1.8

Components: P4M80-M7A (Rev 7.0 & 8.0) ....................................9

Chapter 2:

Hardware Installation ...........................................10

2.1

Central Processing Unit (CPU)......................................................10

2.2

FAN Headers...................................................................................11

2.3

Memory Module Installation ........................................................12

2.4

Connectors and Slots ......................................................................13

Chapter 3:

Headers & Jumpers Setup...................................14

3.1

How to Setup Jumpers ...................................................................14

3.2

Detail Settings..................................................................................14

Chapter 4: Useful Help ..............................................................18
4.1

Award BIOS Beep Code.................................................................18

4.2

Extra Information............................................................................18

4.3

Troubleshooting ..............................................................................20

Chapter 5: WarpSpeeder™ .......................................................21
5.1

Introduction .....................................................................................21

5.2

System Requirement.......................................................................21

5.3

Installation .......................................................................................22

5.4

[WarpSpeeder™] includes 1 tray icon and 5 panels ..................23

P4M80-M7 & P4M80-M7A

CHAPTER 1: INTRODUCTION
1.1

FEATURES

A. Hardware
CPU
Supports Socket 775.
Supports Intel Pentium 4 processor up to 3.8GHz.
(v8.0 supports up to 3.4GHz)
Supports Dual Code CPU.
Front side bus at the following frequency ranges:
533MT/s (133MHz Core Clock)
800MT/s (200MHze Core Clock)
Supports Hyper-Threading Technology.
Chipset
North Bridge: VIA P4M800CE (for P4M80-M7A v1.0 and v7.0).
South Bridge: VIA VT8237R PLUS.
Dimension
ATX Form Factor: 24.38cm (L) x 20.19cm (W)
Main Memory
Supports up to 2 DDR devices.
Supports 133/166/200MHz DDR devices.
Maximum memory size is up to 2GB. (Following table is only for
reference.)
DIMM Socket
Location
DIMM1
DIMM2

DDR Module

Total Memory
Size

128MB/256MB/512MB/1GB *1
128MB/256MB/512MB/1GB *1

Max is 2GB.

Super I/O
Chip: ITE IT8705AF
Provides the most commonly used legacy super I/O
functionality.
Environment Control initiatives:
H/W Monitor,
Fan Speed Controller,
ITE “Smart Guardian” function.

P4M80-M7 & P4M80-M7A
Onboard IDE
Support 4 IDE disk drives.
Supports PIO mode 5, Bus Master, and Ultra DMA
33/66/100/133 function.
LAN
Chip: RealTek RTL8100C (for P4M80-M7/P4M80-M7A v1.0)
VIA VT6103L (for P4M80-M7A v 7.0)
Supports 10/100 Mb/s auto-negotiation operation.
Half/Full duplex capability.
Supports ACPI, PCI power management.
Slot
3 PCI bus master slots.
1 AGP 4x/8x compatible slot.
1 CNR slot.
Serial ATA
Integrated in VT8237R.
Supports RAID 0 and RAID 1 functions.
Supports 2 serial ATA (SATA) ports.
Complaints with SATA Version 1.0 specification.
Data transfer rates up to 150 MB/s.
Onboard AC’97 Sound Codec
Chip: ALC655
Supports 6 channels.
Supports S/PDIF out function.
Compliant with AC’97 Version 2.3 specification.
Front Side Onboard Peripherals
1 front panel header supports front panel facilities.
1 S/PDIF out connector supports digital audio out function
(optional).
1 CD-in connector supports 1 CD-ROM audio-in device.
1 front audio header supports front panel audio function.
1 chassis open header supports PC case-opened warning
function.
1 Floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M
and 2.88Mbytes.
2 USB headers support 4 USB 2.0 ports.
2

P4M80-M7 & P4M80-M7A
2 IDE connectors support 4 hard disk devices.
2 serial ATA connectors support 2 SATA devices.
Rear Side Connectors
4 USB 2.0 ports.
1 VGA port.
1 serial port.
1 parallel port.
1 RJ-45 LAN jack.
1 PS/2 Mouse & Keyboard port.
1 vertical audio port including 1 line-in connector, 1 line out
connector, and 1 MIC in connector.
LAN
PS/2
Mouse

Printer Port

Line In/
Surround
Line Out
VGA1

PS/2
Keyboard

Mic In 1/
Base/Center

COM1
USB x2

USB x2

B. BIOS & Software
BIOS
Award legal BIOS.
Supports APM1.2, ACPI, and USB functions.
Software
Supports 9th TouchTM, FlasherTM, WinFlasherTM, and
WarpspeederTM.
Offers the highest performance for Windows 98SE, Windows NT,
Windows 2000, Windows ME, Windows XP, Red-Hat Linux, and
UNIX series.

1.2

PACKAGE LIST
FDD cable x1
HDD cable x1
User’s Manual x1
Fully Setup Driver CD x1
Rear I/O panel for ATX case x1
USB 2.0 cable x1 (optional)
Serial ATA cable x2 (optional)
S/PDIF out cable x1 (optional)

P4M80-M7 & P4M80-M7A

LAYOUT: P4M80-M7

JKBMS1

JATXPWR1

1.3

JCFAN1

LGA775

JATXPWR2
JCOM1
COM1

CPU1

DIMM1

DIMM2

Parallel Port
VGA1

JVGA1

JUSB1
JUSBV1

P4M800CD

IDE2

JUSBLAN1

IDE1

Super
I/O
JAUDIO

BIOS

AGP1

LAN
RTL8100C

BAT1

PCI1
2
1

2
1

JAUDIO1

JCDIN1

7
JSATA2

VT8237R

PCI2

JUSB3

JSPDIFO1
(optional)

2
1

JUSB4

JSATA1

JUSBV2

PCI3
Codec

CNR1

FDD1

JSFAN1

Note: ■ represents the 1st pin.

2
1

JPANEL1

JCI1
JCMOS1
1
24
23

P4M80-M7 & P4M80-M7A

1.4

COMPONENTS: P4M80-M7
A
U
T

LGA775
CPU1

P4M800CD
Super
I/O

Q
P

BIOS

BAT1

LAN

VT8237R
O

E
F

N
M
L
K

Codec

A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.

JATXPWR2: ATX power connector.
Back panel connectors (rear side).
JUSBV1: USB power header for
JKBMS1, JUSB1, and JUSBLAN1.
JAUDIO1: Front panel audio out
header.
JCDIN1: CD-ROM audio in connector.
JSPDIFO1 (optional): Digital audio out
connector.
CNR1: Communication Network Riser
slot.
PCI1~3: Peripheral Component
Interconnect slots.
FDD1: Floppy disk connector.
JSFAN1: System fan header.
JPANEL1: front panel facilities header.

L.
M.
N.

JCMOS1: Clear CMOS header.
JCI1: Chassis open message header.
JUSBV2: USB power header for
JUSB3/4.
JSATA1/2: Serial ATA connectors.

P.
Q.

JUSB3/4: Front USB headers.
AGP1: Accelerated Graphics Port slot.

IDE1/2: Hard disk connectors.

DIMM1/2: DDR memory modules.

T.
U.

JATXPWR1: ATX power connector.
JCFAN1: CPU fan header.

P4M80-M7 & P4M80-M7A

1.5

LAYOUT: P4M80-M7A (REV 1.0)
JATXPWR1

JKBMS1
JCFAN1

LGA775

JCOM1

JATXPWR2

JUSBLAN1

P4M800CE

IDE2

JUSBV1

IDE1

JUSB1

DIMM2

DIMM1

JVGA1

JPRNT1

CPU1

Super
I/O
JAUDIO

BIOS

AGP1

LAN
RTL8100C

BAT1

PCI1
JUSB3

JCDIN1
JAUX1
(optional)

VT8237R

PCI2

JAUDIO1

JSATA2

JUSB4

JSPDIFO1
(optional)

JSATA1

JUSBV2

PCI3

Codec
JSFAN1

CNR1

FDD1

Note: ■ represents the 1st pin.

JPANEL1

JCI1
JCMOS1

P4M80-M7 & P4M80-M7A

1.6

COMPONENTS: P4M80-M7A (REV 1.0)
A
V

LGA775

P4M800CE

R
Q

D
E
F
G

VT8237R

O
N
M
L

H
I

A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.

JATXPWR2: ATX power connector.
Back panel connectors (rear side).
JUSBV1: USB power header for back
panel.
JAUDIO1: Front panel audio out
header.
JSPDIFO1 (optional): Digital audio out
connector.
JCDIN1: CD-ROM audio in connector.
CNR1: Communication Network Riser
slot.
JAUX1:
PCI1~3: Peripheral Component
Interconnect slots.
FDD1: Floppy disk connector.
JSFAN1: System fan header.

L.
M.
N.

JPANEL1: front panel facilities header.
JCMOS1: Clear CMOS header.
JCI1: Chassis open message header.

O.
P.

JUSBV2: USB power header for front
panel.
JSATA1/2: Serial ATA connectors.

Q.
R.

JUSB3/4: Front USB headers.
AGP1: Accelerated Graphics Port slot.

S.
T.

IDE1/2: Hard disk connectors.
DIMM1/2: DDR memory modules.

U.
V.

JATXPWR1: ATX power connector.
JCFAN1: CPU fan header.

P4M80-M7 & P4M80-M7A

1.7

LAYOUT: P4M80-M7A (REV 7.0 & 8.0)
JATXPWR1

JKBMS1
JCFAN1

LGA775

JCOM1

JATXPWR2

JUSB1

DIMM2

DIMM1

JVGA1

JPRNT1

CPU1

P4M800CE

IDE2

JUSBLAN1

IDE1

JUSBV1

Super
I/O
JAUDIO

BIOS

AGP1

LAN
VT6103L

BAT1

PCI1
JUSB3

JCDIN1
JAUX1
(optional)

VT8237R

PCI2

JAUDIO1

JSATA2

JUSB4

JSPDIFO1
(optional)

JSATA1

JUSBV2

PCI3

Codec
JSFAN1

CNR1

FDD1

Note: ■ represents the 1st pin.

JPANEL1

JCI1
JCMOS1

P4M80-M7 & P4M80-M7A

1.8

COMPONENTS: P4M80-M7A (REV 7.0 & 8.0)
A
V

LGA775

P4M800CE

R
Q

D
E
F
G

VT8237R

O
N
M
L

H
I

A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.

L.
M.
N.

JPANEL1: front panel facilities header.
JCMOS1: Clear CMOS header.
JCI1: Chassis open message header.

O.
P.

JUSBV2: USB power header for front
panel.
JSATA1/2: Serial ATA connectors.

Q.
R.

JUSB3/4: Front USB headers.
AGP1: Accelerated Graphics Port slot.

S.
T.

IDE1/2: Hard disk connectors.
DIMM1/2: DDR memory modules.

U.
V.

JATXPWR1: ATX power connector.
JCFAN1: CPU fan header.

P4M80-M7 & P4M80-M7A

CHAPTER 2: HARDWARE INSTALLATION
2.1

CENTRAL PROCESSING UNIT (CPU)

Special Notice:
Remove Pin Cap before installation, and make good preservation for future use.
When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin
legs won’t be damaged.

Pin Cap

Step 1: Pull the lever sideways away from the socket and then raise the
lever up to a 90-degree angle.

Step 2: Look for the black cut edge on socket, and the white dot on CPU
should point wards this black cut edge. The CPU will fit only in the
correct orientation.
Step 2-1:

P4M80-M7 & P4M80-M7A
Step 2-2:

Step 3: Hold the CPU down firmly, and then close the lever to complete
the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN
power cable to the JCFAN1. This completes the installation.

2.2

FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
wiring and plug may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU FAN Header: JCFAN1

JCFAN1

Pin
1
2
3
4

Assignment
Ground
Power (+12V)
FAN RPM rate sense
Smart Fan Control

System Fan Header: JSFAN1
1

JSFAN1

Pin
1
2
3

Assignment
Ground
Power (+12V)
FAN RPM rate sense

Note:
The JCFAN1 and JSFAN1 support 4-pin and 3-pin head connector.
When connecting with wires onto connectors, please note that the red
wire is the positive and should be connected to pin#2, and the black
wire is Ground and should be connected to GND.
11

P4M80-M7 & P4M80-M7A

2.3

MEMORY MODULE INSTALLATION

Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

Note:
To assure the system safety, if you need to change DDR modules, firstly,
please unplug the 20-pin power cable with the power connector, and
then you can change the modules. Afterwards, plug in the cable the
power connector again, and finally you can boot up the system.

P4M80-M7 & P4M80-M7A

2.4

CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that
supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This
connector supports the provided floppy drive ribbon cables.

IDE1/IDE2: Hard Disk Connectors
The motherboard has a 32-bit Enhanced PCI IDE Controller that
provides PIO Mode 0~5, Bus Master, and Ultra DMA 33/ 66/ 100
functionality. It has two HDD connectors IDE1 (primary) and IDE2
(secondary).
The IDE connectors can connect a master and a slave drive, so you can
connect up to four hard disk drives. The first hard drive should always be
connected to IDE1.

PCI1~PCI3: Peripheral Component Interconnect Slots
This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for
expansion cards. This PCI slot is designated as 32 bits.

AGP1: Accelerated Graphics Port Slot
Your monitor will attach directly to that video card. This motherboard
supports video cards for PCI slots, but it is also equipped with an
Accelerated Graphics Port (AGP). An AGP card will take advantage of
AGP technology for improved video efficiency and performance,
especially with 3D graphics.

CNR1: Communication Network Riser Slot
The CNR specification is an open Industry Standard Architecture, and it
defines a hardware scalable riser card interface, which supports modem
only.

JSATA1/JSATA2: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 2 channels SATA
interface, it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s.
1

JSATA1~2

Pin
1
3
5
7

Assignment
Ground
TXRXGround

Pin
2
4
6

Assignment
TX+
Ground
RX+

P4M80-M7 & P4M80-M7A

CHAPTER 3: HEADERS & JUMPERS SETUP
3.1

HOW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened

3.2

Pin closed

Pin1-2 closed

DETAIL SETTINGS

JUSBV1/JUSBV2: Power Source Headers for USB ports
JUSBV1/JUSBV2
1

Pin 1-2 close

Pin 2-3 close

Assignment
+5V

+5V Standby
Voltage

Description
JUSBV1: +5V for JKBMS1, JUSB1
and JUSBLAN1.
JUSBV2: +5V for JUSB3/4.
JUSBV1: JKBMS1, JUSB1 and
JUSBLAN1 are powered with +5V
standby voltage.
JUSBV2: JUSB3/4 are powered by
+5V standby voltage.

Note:
In order to support this function “Power-on system via keyboard and mouse”,
“JUSBV1/JUSBV2” jumper cap should be placed on Pin 2-3.

JUSB3/JUSB4: Front USB Headers
This motherboard provides 2 USB 2.0 headers, which allows user to
connect additional USB cable on the PC front panel, and also can be
connected with internal USB devices, like USB card reader.

2
1

JUSB3/JUSB4

Pin
1
3
5
7
9

Assignment
+5V (fused)
USBUSB+
Ground
Key

Pin
2
4
6
8
10

Assignment
+5V (fused)
USBUSB+
Ground
N/A

P4M80-M7 & P4M80-M7A
JATXPWR1/PATXPWR2: Power Connectors
JATXPWR1: This connector allows user to connect with 20-pin power
connector on the ATX power supply.
JATXPWR2: By connecting this connector, it will provide +12V to CPU
power circuit.
10

JATXPWR1
2

1
3

JATXPWR2

Pin
1
2
3
4
5
6
7
8
9
10
Pin
1
2

Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_ON
Standby Voltage +5V
+12V
Assignment
+12V
+12v

Pin
11
12
13
14
15
16
17
18
19
20
Pin
3
4

Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
-5V
+5V
+5V
Assignment
Ground
Ground

JAUDIO1: Front Panel Audio Header
This header allows user to connect the front audio out put cable with the
PC front panel. It will disable the output on back panel audio connectors.
14
13

2
1

Pin
Assignment
1 Mic in/center
3 Mic power/Bass
Right line out/Speaker out
5
Right
7 Reserved
9 Left line out/Speaker out Left
Right line in/Rear speaker
11
Right
13 Left line in/Rear speaker Left

JAUDIO1
Pin
Assignment
2 Ground
4 Audio power
6 Right line out/Speaker out Right
8 Key
10 Left line out/Speaker out Left
12 Right line in/Rear speaker Right
14 Left line in/Rear speaker Left

P4M80-M7 & P4M80-M7A
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the veriaty
devices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card
etc..

JCDIN1

Pin
1
2
3
4

Assignment
Left channel input
Ground
Ground
Right channel input

JSPDIFO1: Digital Audio-out Connector (optional)
This connector allows user to connect the PCI bracket SPDIF output
header.
Pin
1
2
3

1
JSPDIFO1

Assignment
+5V
SPDIF_OUT
Ground

JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe
setting and the CMOS data, please carefully follow the procedures to
avoid damaging the motherboard.
JCMOS1

Assignment
Normal Operation (Default).

Pin 1-2 close

Clear CMOS data.

Pin 2-3 close

※ Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.

P4M80-M7 & P4M80-M7A
JCI1: Chassis Open Header
This connector allows system to monitor PC case open status. If the
signal has been triggered, it will record to the CMOS and show the
message on next boot-up.
Pin
1
2

JCI1

Assignment
Case open signal
Ground

JPANEL1: Front Panel Header
This 24-pin connector includes Power-on, Reset, HDD LED, Power LED,
Sleep button, speaker and IrDA Connection. It allows user to connect
the PC case’s front panel switch functions.
SLP

PWR_LED
On/Off

2
1

24
23

+ SPK

Pin
1
3
5
7
9
11
13
15
17
19
21
23

+ + -

Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
N/A
N/A
+5V
IRTX

RST
HLED

Function

Pin
2
4
6
8
10
12
14
16
18
20
22
24

Speaker
Connector
Hard drive
LED
Reset
button
IrDA
Connector

JPANEL1
Assignment
Sleep control
Ground
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Key
Key
Ground
IRRX

Function
Sleep
button
N/A
Power LED
Power-on
button
IrDA
Connector

P4M80-M7 & P4M80-M7A

CHAPTER 4: USEFUL HELP
4.1

AWARD BIOS BEEP CODE

Beep Sound
One long beep followed by two short
beeps
High-low siren sound

Meaning
Video card not found or video card
memory bad
CPU overheated
System will shut down automatically
One Short beep when system boot-up No error found during POST
Long beeps every other second
No DRAM detected or install

4.2

EXTRA INFORMATION

A. BIOS Update
After you fail to update BIOS or BIOS is invaded by virus, the
Boot-Block function will help to restore BIOS. If the following message
is shown after boot-up the system, it means the BIOS contents are
corrupted.

In this Case, please follow the procedure below to restore the BIOS:
1. Make a bootable floppy disk.
2. Download the Flash Utility “AWDFLASH.exe” from the Biostar
website: www.biostar.com.tw
3. Confirm motherboard model and download the respectively BIOS
from Biostar website.
4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.
5. Insert the bootable disk into floppy drive and press Enter.
6. System will boot-up to DOS prompt.
7. Type “Awdflash xxxx.bf/sn/py/r” in DOS prompt.
(xxxx means BIOS name.)
8. System will update BIOS automatically and restart.
9. The BIOS has been recovered and will work properly.

P4M80-M7 & P4M80-M7A
B. CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.

P4M80-M7 & P4M80-M7A

4.3

TROUBLESHOOTING

Probable
No power to the system at all
Power light don’t illuminate, fan
inside power supply does not turn
on.
2.
Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.
System does not boot from hard disk
drive, can be booted from optical drive.
1.

1.
2.
3.

Solution
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from optical drive. 1.
Back up data and applications
Hard disk can be read and applications
files.
can be used but booting from hard disk 2.
Reformat the hard drive.
is impossible.
Re-install applications and data
using backup disks.
Screen message says “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
Cannot boot system after installing
1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

P4M80-M7 & P4M80-M7A

CHAPTER 5: WARPSPEEDER™

5.1

INTRODUCTION

[WarpSpeeder™], a new powerful control utility, features three
user-friendly functions including Overclock Manager, Overvoltage
Manager, and Hardware Monitor.
With the Overclock Manager, users can easily adjust the frequency they
prefer or they can get the best CPU performance with just one click. The
Overvoltage Manager, on the other hand, helps to power up CPU core
voltage and Memory voltage. The cool Hardware Monitor smartly indicates
the temperatures, voltage and CPU fan speed as well as the chipset
information. Also, in the About panel, you can get detail descriptions about
BIOS model and chipsets. In addition, the frequency status of CPU,
memory, AGP and PCI along with the CPU speed are synchronically
shown on our main panel.
Moreover, to protect users' computer systems if the setting is not
appropriate when testing and results in system fail or hang,
[WarpSpeeder™] technology assures the system stability by automatically
rebooting the computer and then restart to a speed that is either the
original system speed or a suitable one.

5.2

SYSTEM REQUIREMENT

OS Support: Windows 98 SE, Windows Me, Windows 2000, Windows XP
DirectX: DirectX 8.1 or above. (The Windows XP operating system
includes DirectX 8.1. If you use Windows XP, you do not need to install
DirectX 8.1.)

P4M80-M7 & P4M80-M7A

5.3

INSTALLATION

1. Execute the setup execution file, and then the following dialog will pop
up. Please click “Next” button and follow the default procedure to
install.

2. When you see the following dialog in setup procedure, it means setup
is completed. If the “Launch the WarpSpeeder Tray Utility” checkbox
is checked, the Tray Icon utility and [WarpSpeeder™] utility will be
automatically and immediately launched after you click “Finish”
button.

Usage:
The following figures are just only for reference, the screen printed in
this user manual will change according to your motherboard on hand.
22

P4M80-M7 & P4M80-M7A

5.4

[WARPSPEEDER™] INCLUDES 1 TRAY ICON AND 5 PANELS

1. Tray Icon:
Whenever the Tray Icon utility is launched, it will display a little tray
icon on the right side of Windows Taskbar.

This utility is responsible for conveniently invoking [WarpSpeeder™]
Utility. You can use the mouse by clicking the left button in order to
invoke [WarpSpeeder™] directly from the little tray icon or you can
right-click the little tray icon to pop up a popup menu as following
figure. The “Launch Utility” item in the popup menu has the same
function as mouse left-click on tray icon and “Exit” item will close
Tray Icon utility if selected.

P4M80-M7 & P4M80-M7A
2. Main Panel
If you click the tray icon, [WarpSpeeder™] utility will be invoked.
Please refer to the following figure; the utility’s first window you will
see is Main Panel.
Main Panel contains features as follows:
a.
Display the CPU Speed, CPU external clock, Memory clock,
AGP clock, and PCI clock information.
b.
Contains About, Voltage, Overclock, and Hardware Monitor
Buttons for invoking respective panels.
c.
With a user-friendly Status Animation, it can represent 3
overclock percentage stages:
Man walking→overclock percentage from 100% ~ 110 %
Panther running→overclock percentage from 110% ~ 120%
Car racing→overclock percentage from 120% ~ above

P4M80-M7 & P4M80-M7A
3. Voltage Panel
Click the Voltage button in Main Panel, the button will be highlighted
and the Voltage Panel will slide out to up as the following figure.
In this panel, you can decide to increase CPU core voltage and
Memory voltage or not. The default setting is “No”. If you want to get
the best performance of overclocking, we recommend you click the
option “Yes”.

P4M80-M7 & P4M80-M7A
4. Overclock Panel
Click the Overclock button in Main Panel, the button will be
highlighted and the Overclock Panel will slide out to left as the
following figure.

Overclock Panel contains the these features:
a.
“–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3MHz
button”: provide user the ability to do real-time overclock
adjustment.
Warning:
Manually overclock is potentially dangerous, especially when the
overclocking percentage is over 110 %. We strongly recommend you
verify every speed you overclock by click the Verify button. Or, you can
just click Auto overclock button and let [WarpSpeeder™] automatically
gets the best result for you.

“Recovery Dialog button”: Pop up the following dialog. Let user
select a restoring way if system need to do a fail-safe reboot.

P4M80-M7 & P4M80-M7A
c.

“Auto-overclock button”: User can click this button and
[WarpSpeeder™] will set the best and stable performance and
frequency automatically. [WarpSpeeder™] utility will execute a
series of testing until system fail. Then system will do fail-safe
reboot by using Watchdog function. After reboot, the
[WarpSpeeder™] utility will restore to the hardware default
setting or load the verified best and stable frequency according
to the Recovery Dialog’s setting.
“Verify button”: User can click this button and [WarpSpeeder™]
will proceed a testing for current frequency. If the testing is ok,
then the current frequency will be saved into system registry. If
the testing fail, system will do a fail-safe rebooting. After reboot,
the [WarpSpeeder™] utility will restore to the hardware default
setting or load the verified best and stable frequency according
to the Recovery Dialog’s setting.
Note:
Because the testing programs, invoked in Auto-overclock and Verify,
include DirectDraw, Direct3D and DirectShow tests, the DirectX 8.1 or
newer runtime library is required. And please make sure your display
card’s color depth is High color (16 bit) or True color( 24/32 bit ) that is
required for Direct3D rendering.

5. Hardware Monitor Panel
Click the Hardware Monitor button in Main Panel, the button will be
highlighted and the Hardware Monitor panel will slide out to left as
the following figure.
In this panel, you can get the real-time status information of your
system. The information will be refreshed every 1 second.

P4M80-M7 & P4M80-M7A
6. About Panel
Click the “about” button in Main Panel, the button will be highlighted
and the About Panel will slide out to up as the following figure.
In this panel, you can get model name and detail information in hints
of all the chipset that are related to overclocking. You can also get
the mainboard’s BIOS model and the Version number of
[WarpSpeeder™] utility.

P4M80-M7 & P4M80-M7A
Note:
Because the overclock, overvoltage, and hardware monitor features
are controlled by several separate chipset, [WarpSpeeder™] divide
these features to separate panels. If one chipset is not on board, the
correlative button in Main panel will be disabled, but will not interfere
other panels’ functions. This property can make [WarpSpeeder™]
utility more robust.

02/27, 2006

P4M80-M7 BIOS Manual
BIOS Setup ............................................................................... 2
1 Main Menu..................................................................................................... 4
2 Standard CMOS Features .............................................................................. 7
3 Advanced BIOS Features............................................................................. 10
4 Advanced Chipset Features ......................................................................... 14
5 Integrated Peripherals .................................................................................. 20
6 Power Management Setup ........................................................................... 25
7 PnP/PCI Configurations............................................................................... 30
8 PC Health Status .......................................................................................... 33
9 Frequency/ Voltage Control......................................................................... 35

P4M80-M7 BIOS Manual
BIOS Setup
Introduction
This manual discussed Award™ Setup program built into the ROM BIOS. The Setup
program allows users to modify the basic system configuration. This special information is
then stored in battery-backed RAM so that it retains the Setup information when the power
is turned off.
The Award BIOS™ installed in your computer system’s ROM (Read Only Memory) is a
custom version of an industry standard BIOS. This means that it supports Intel Pentium ® 4
processor input/output system. The BIOS provides critical low-level support for standard
devices such as disk drives and serial and parallel ports.
Adding important has customized the Award BIOS™, but nonstandard, features such as
virus and password protection as well as special support for detailed fine-tuning of the
chipset controlling the entire system.
The rest of this manual is intended to guide you through the process of configuring your
system using Setup.

Plug and Play Support
These AWARD BIOS supports the Plug and Play Version 1.0A specification. ESCD
(Extended System Configuration Data) write is supported.

EPA Green PC Support
This AWARD BIOS supports Version 1.03 of the EPA Green PC specification.

APM Support
These AWARD BIOS supports Version 1.1&1.2 of the Advanced Power Management
(APM) specification. Power management features are implemented via the System
Management Interrupt (SMI). Sleep and Suspend power management modes are supported.
Power to the hard disk drives and video monitors can be managed by this AWARD BIOS.

ACPI Support
Award ACPI BIOS support Version 1.0 of Advanced Configuration and Power interface
specification (ACPI). It provides ASL code for power management and device
configuration capabilities as defined in the ACPI specification, developed by Microsoft,
Intel and Toshiba.

P4M80-M7 BIOS Manual
PCI Bus Support
This AWARD BIOS also supports Version 2.1 of the Intel PCI (Peripheral Component
Interconnect) local bus specification.

DRAM Support
DDR SDRAM (Double Data Rate Synchronous DRAM) are supported.

Supported CPUs
This AWARD BIOS supports the AMD CPU.

Using Setup
In general, you use the arrow keys to highlight items, press to select, use the
and keys to change entries, press for help and press to quit.
The following table provides more detail about how to navigate in the Setup program by
using the keyboard.

Keystroke
Up arrow
Down arrow
Left arrow
Right arrow
Move Enter
PgUp key
PgDn key
+ Key
- Key
Esc key
F1 key
F5 key
F7 key
F10 key

Function
Move to previous item
Move to next item
Move to the item on the left (menu bar)
Move to the item on the right (menu bar)
Move to the item you desired
Increase the numeric value or make changes
Decrease the numeric value or make changes
Increase the numeric value or make changes
Decrease the numeric value or make changes
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu – E xit
Current page and return to Main Menu
General help on Setup navigation keys
Load previous values from CMOS
Load the optimized defaults
Save all the CMOS changes and exit

P4M80-M7 BIOS Manual
1 Main Menu
Once you enter Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the
screen. The Main Menu allows you to select from several setup functions. Use the arrow
keys to select among the items and press to accept and enter the sub-menu.
!! WARNING !!
The information about BIOS defaults on manual (Figure
1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS
installed on board, for update information.

Main Menu

Standard CMOS Features
This submenu contains industry standard configurable options.

Advanced BIOS Features
This submenu allows you to configure enhanced features of the BIOS.

Advanced Chipset Features
This submenu allows you to configure special chipset features.

P4M80-M7 BIOS Manual
Integrated Peripherals
This submenu allows you to configure certain IDE hard drive options and Programmed
Input/ Output features.
Power Management Setup
This submenu allows you to configure the power management features.

PnP/PCI Configurations
This submenu allows you to configure certain “Plug and Play” and PCI options.

PC Health Status
This submenu allows you to monitor the hardware of your system.

Frequency/ Voltage Control
This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock. (However,
this function is strongly recommended not to use. Not properly change the voltage
and clock may cause the CPU or M/B damage!)

Load Optimized Defaults
This selection allows you to reload the BIOS when the system is having problems
particularly with the boot sequence. These configurations are factory settings optimized
for this system. A confirmation message will be displayed before defaults are set.

Set Supervisor Password
Setting the supervisor password will prohibit everyone except the supervisor from making
changes using the CMOS Setup Utility. You will be prompted with to enter a password.

P4M80-M7 BIOS Manual
Set User Password
If the Supervisor Password is not set, then the User Password will function in the same way
as the Supervisor Password.
If the Supervisor Password is set and the User Password is
set, the “User” will only be able to view configurations but will not be able to change them.

Save & Exit Setup
Save all configuration changes to CMOS(memory) and exit setup. Confirmation message
will be displayed before proceeding.

Exit Without Saving
Abandon all changes made during the current session and exit setup.
message will be displayed before proceeding.

Upgrade BIOS
This submenu allows you to upgrade bios.

confirmation

P4M80-M7 BIOS Manual
2 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into 10 categories. Each category
includes no, one or more than one setup items. Use the arrow keys to highlight the item and
then use the or keys to select the value you want in each item.

P4M80-M7 BIOS Manual
Main Menu Selections
This table shows the selections that you can make on the Main Menu.

Item

Options

Date

mm : dd : yy

Set the system date. Note
that the ‘Day’ automatically
changes when you set the
date.

Time

hh : mm : ss

Set the
clock.

IDE Primary Master

Options are in its sub
menu.

Press to enter the
sub menu of detailed
options

IDE Primary Slave

Options are in its sub
menu.

Press to enter the
sub menu of detailed
options.

IDE Secondary Master Options are in its sub
menu.

Press to enter the
sub menu of detailed
options.

IDE Secondary Slave

Options are in its sub
menu.

Press to enter the
sub menu of detailed
options.

Drive A

360K, 5.25 in

Drive B

1.2M, 5.25 in

Select the type of floppy
disk drive installed in your
system.

720K, 3.5 in

Description

system internal

1.44M, 3.5 in
2.88M, 3.5 in
None
Video

EGA/VGA
CGA 40
CGA 80
MONO

Select the default
device.

video

P4M80-M7 BIOS Manual
Item
Halt On

Options

Description

All Errors

Select the situation in which

No Errors

you want the BIOS to stop

All, but Keyboard
All, but Diskette

the POST process and
notify you.

All, but Disk/ Key
Base Memory

N/A

Displays the amount of
conventional memory
detected during boot up.

Extended Memory

N/A

Displays the amount of
extended memory detected
during boot up.

Total Memory

N/A

Displays the total memory
available in the system.

P4M80-M7 BIOS Manual
3 Advanced BIOS Features

3.1 CPU FEATURE

3.1.1

Delay Prior to Thermal

Set this item to enable the CPU Thermal function to engage after the specified time.
The Choices: 4, 8, 16 (default), 32.

P4M80-M7 BIOS Manual
3.1.2

Thermal Management

Allow you to choose the thermal management method of your monitor.
The Choices:Thermal Monitor 1 (default), Thermal Monitor2.
Notes:The choices will be different according to your CPU features.

3.1.3

TM2 Bus Ratio

Represents the frequency. Bus ratio of the throttled performance state
that will be initiated when the on-die sensor goes from not hot to hot.
The Choices: 0X (default).

3.1.4

TM2 Bus VID

Represents the voltage of the throttled performance state that will be
initiated when the on-die sensor goes from not hot to hot.
The Choices:0.8375 (default).

3.1.5

Limit CPU ID Max Val

Set limit CPU ID maximum vale to 3, it should be disabled for Win XP.
The Choices: Disabled (default), Enabled.

3.1.6 Execute Disable Bit
When disabled ,forces the XD feature flag to always return 0.
The Choices: Disabled (default), Enabled.

3.1.7

Virtualization Technology

This item Allow you to enabled or disabled Virtualization Technology.
The Choices: Enabled (default), Disabled.

3.2 Hard Disk Boot Priority

P4M80-M7 BIOS Manual
These BIOS attempt to load the operating system from the device in the sequence selected in
these items.
The Choices:
Pri. Master, Pri.Slave, Sec.Master, Sec. Slave, USBHDD0, USBHDD1, USBHDD2 and
Bootable Add-in Carde.

3.3 Virus Warning
This option allows you to choose the Virus Warning feature that is used to protect the IDE
Hard Disk boot sector. If this function is enabled and an attempt is made to write to the
boot sector, BIOS will display a warning message on the screen and sound an alarm beep.
Disabled (default)
Enabled

Virus protection is disabled.
Virus protection is activated.

3.4 CPU L1&L2 Cache
Depending on the CPU/chipset in use, you may be able to increase
memory access time with this option.
Enabled (default)
Enable cache.
Disabled
Disable cache.

3.5 CPU L3 Cache
Depending on the CPU/chipset in use, you may be able to increase
memory access time with this option.
Enabled (default) Enable cache.
Disabled Disable cache.

3.6 Hyper-Threading Technology
This option allows you to enable or disabled CPU Hyper-Threading.
Enabled for Windows XP and Linux 2.4.x (OS optimized for Hyper
Threading Technology. Disabled for other OS (OS not optimized for
Hyper Threading Technology.
The Choices:Enabled (Default), Disabled.

3.7 CPU L2 Cache ECC Checking
This item allows you to enable/disable CPU L2 Cache ECC Checking.
The Choices:Enabled (default), Disabled.

3.8 Quick Power On Self Test
Enabling this option will cause an abridged version of the Power On Self-Test (POST) to
execute after you power up the computer.
Enabled (default)
Enable quick POST.
Disabled
Normal POST.

P4M80-M7 BIOS Manual
3.9 First/ Second/ Third/ Boot Other Device
These BIOS attempt to load the operating system from the device in the sequence selected
in these items.
The Choices:Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, IP100,
LAN, HPT370, Disabled, Enabled.
3.10 Swap Floppy Drive
For systems with two floppy drives, this option allows you to swap logical drive
assignments.
The Choices:Disabled (default), Enabled.

3.11 Boot Up Floppy Seek
Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks.
Disabling this option reduces the time it takes to boot-up.
The Choices:Enabled (default), Disabled.
3.12 Boot Up NumLock Status
Selects the NumLock. State after power on.
The Choices: On (default)
Numpad is number keys.
Off
Numpad is arrow keys.

3.13 Typematic Rate Setting
When a key is held down, the keystroke will repeat at a rate determined by the keyboard
controller. When enabled, the typematic rate and typematic delay can be configured.
The Choices:Disabled (default), Enabled.

3.14 Typematic Rate (Chars/Sec)
Sets the rate at which a keystroke is repeated when you hold the key down.
The Choices:6 (default), 8, 10, 12, 15, 20, 24, 30.

3.15 Typematic Delay (Msec)
Sets the delay time after the key is held down before it begins to repeat the keystroke.
The Choices:250 (default), 500,750,1000.

3.16 Security Option
This option will enable only individuals with passwords to bring the system online and/or to
use the CMOS Setup Utility.
System
A password is required for the system to boot and is also required to
access the Setup Utility.
Setup (default)
A password is required to access the Setup Utility only.
This will only apply if passwords are set from the Setup main menu.

P4M80-M7 BIOS Manual
4 Advanced Chipset Features
This submenu allows you to configure the specific features of the chipset installed on your
system. This chipset manage bus speeds and access to system memory resources, such as
DRAM. It also coordinates communications with the PCI bus. The default settings that came
with your system have been optimized and therefore should not be changed unless you are
suspicious that the settings have been changed incorrectly.

P4M80-M7 BIOS Manual
4.1 DRAM Clock/Drive Control

To control the Clock/Drive. If you highlight the literal “Press Enter” next to the “DRAM
Clock/Drive Control” label and then press the enter key, it will take you a submenu with the
following options:

4.1.1

DRAM Clock

This item determines DRAM clock following 100MHz, 133MHz, 166MHz or By SPD.
The Choices: 100MHz, 133MHz, By SPD (default), 166MHz

4.1.2

DRAM Timing

This item determines DRAM clock/ timing follow SPD or not.
The Choices: Auto By SPD (default), Manual, Turbo, Ultra.

4.1.3

SDRAM CAS Latency

When SDRAM is installed, the number of clock cycles of CAS latency depends on the
SDRAM timing.
The Choices: 2.5 /4 (default), 2.

4.1.4

Bank Interleave

This item allows you to enable or disable the bank interleave feature.
The Choices: Disabled (default), 2 bank, 4 bank.

4.1.5

Precharge to Active (Trp)

This items allows you to specify the delay from precharge command to activate
command.
The Choices: 2T, 3T, 5T,4T (default).

P4M80-M7 BIOS Manual
4.1.6

Active to Precharge (Tras)

This items allows you to specify the minimum bank active time.
The Choices: 07T (default), 6T.

4.1.7

Active to CMD (Trcd)

Use this item to specify the delay from the activation of a bank to the time that a read
or write command is accepted.
The Choices: 2T, 3T, 5T, 4T (default).

4.1.8

REF to ACT/REF to REF (Trfc)

This item allows you to determine the selection for REF to ACT/REF to REF (Trfc)
The Choices: 15T,25T (default).

4.1.9

ACT (0) to ACT(1) (TRRD)

This item allows you to determine the selection.for ACT (0) to ACT(1) (TRRD).
The Choices: 3T (default).

4.1.10

Read to Precharge (Trtp)

This item allows you to determine the selection.for Read to Precharge(Trtp).
The Choices: 2T (default).

4.1.11

Write to Read CMD (Twtr)

This item allows you to determine the selection.for Write to Read CMD (Twtr).
The Choices: 1T/2T (default).

4.1.12

Write Recoverry Time (Twr)

This item allows you to determine the selection.for Write Recoverry Time (Twr).
The Choices: 4T (default).

4.1.13

DRAM Command Rate

This item controls clock cycle that must occur between the last valid write operation
and the next command.
The Choices: 1T Command, 2T Command (default).

4.1.14

RDSAIT mode

This item allows you to select the RDSAIT mode.
The Choices: Auto (default).

4.1.15

RDSAIT selection

This item allows you to make selection for RDSAIT.
The Choices: 03 (default).

P4M80-M7 BIOS Manual
4.2 AGP & P2P Bridge Control

If you highlight the literal “Press Enter” next to the “AGP & P2P Bridge Control” label and
then press the enter key, it will take you a submenu with the following options:

4.2.1

AGP Aperture Size

Select the size of the Accelerated Graphics Port (AGP) aperture. The aperture
is a portion of the PCI memory address range dedicated for graphics memory
address space. Host cycles that hit the aperture range are forwarded to the AGP
without any translation.
The Choices: 64M, 256M, 128M (default), 32M, 16M, 8M, 4M.

4.2.2

AGP 2.0 Mode
This item allows you to select the AGP Mode.
The Choices: 4X (default), 2X, 1X.

4.2.3

AGP Driving Control

By choosing “Auto” the system BIOS will the AGP output Buffer Drive
strength P Ctrl by AGP Card. By choosing “Manual”, it allows user to set AGP
output Buffer Drive strength P Ctrl by manual.
The Choices: Auto (default), Manual.

4.2.4 AGP Driving Value
.

While AGP driving control item set to “Manual”, it allows user to set AGP
driving.
The Choices: DA (default).

P4M80-M7 BIOS Manual
4.2.5

AGP Fast Write

This item allows you to disabled or enabled AGP Fast Write.
The Choices: Disabled (default),Enabled.

4.2.6 AGP Master 1 WS Write
When Enabled, writes to the AGP (Accelerated Graphics Port) are executed
with one-wait states.
The Choices: Disabled (default), Enabled.

4.2.7 AGP Master 1 WS Read
When Enabled, read to the AGP (Accelerated Graphics Port) are executed with
one wait states.
The Choices: Disabled (default), Enabled.

4.2.8 AGP 3.0 Calibration cycle
This item allows you to disabled or enabled AGP 3.0 Calibration Cycle.
The Choices: Disabled (default), Enabled.

4.2.9 VGA Share Memory Size
This item allows you to select the VGA share memory size.
The Choices: 64M (default), Disabled.

4.2.10 Direct Frame Buffer
This item allows you to disabled or enabled direct frame buffer.
The Choices: Enabled (default),Disabled.

4.3 CPU & PCI Bus Control

P4M80-M7 BIOS Manual
If you highlight the literal “Press Enter” next to the “CPU & PCI Bus Control” label and then
press the enter key, it will take you a submenu with the following options:

4.3.1 PCI Master 0 WS Write

When enabled, writes to the PCI bus are executed with zero-wait states.
The Choices: Enabled (default), Disabled.

4.3.2 PCI Delay Transaction
The chipset has an embedded 32-bit posted write buffer to support delay transactions
cycles.
Select Enabled to support compliance with PCI specification.
The Choices: Enabled (default), Disabled.

4.3.3 Vlink mode selection
This item allows you to select Vlink mode.
The Choices: By Auto (default).Mode 1.

4.3.4 VLink 8X Support
This item allows you to enable or disable VLink 8X support.
The Choices: Enabled (default), Disabled.

4.3.5 DRDY_Timing
This item allows you to select DRDY_Timing.
The Choices: Default (default).

4.4 Memory Hole
When enabled, you can reserve an area of system memory for ISA adapter ROM. When
this area is reserved, it cannot be cached. Refer to the user documentation of the peripheral
you are installing for more information.
The Choices: Disabled (default), 15M – 16M.

4.5 System BIOS Cacheable
Selecting the “Enabled” option allows caching of the system BIOS ROM at
F0000h-FFFFFh, which can improve system performance. However, any programs writing
to this area of memory will cause conflicts and result in system errors.
The Choices: Enabled (default), Disabled

4.6 Init Display First
With systems that have multiple video cards, this option determines
whether the primary display uses a PCI Slot or an AGP Slot.
The Choices: PCI Slot (default), AGP.

P4M80-M7 BIOS Manual
5 Integrated Peripherals

5.1 VIA OnChip IDE Device

The chipset contains a PCI IDE interface with support for two IDE channels.
Select “Enabled” to activate the first and / or second IDE interface. If you install a primary
and / or secondary add-in IDE interface, select “Disabled” to deactivate an interface. If you
highlight the literal “Press Enter” next to the “Onchip IDE Control” label and then press the
enter key, it will take you a submenu with the following options:

P4M80-M7 BIOS Manual
5.1.1 OnChip SATA
This option allows you to enable the onchip Serial ATA.
The Choices: Enabled (default), Disabled.

5.1.2 SATA Mode
This option allows you to select SATA Mode.
The Choices: RAID (default), IDE.

5.1.3 IDE DMA Transfer Access
This item allows you to enable or disable the IDE transfer access.
The Choices: Enabled (default), Disabled.

5.1.3 IDE Channel 0/1
The motherboard chipset contains a PCI IDE interface with support for
two IDE channels. Select “Enabled” to activate the first and/or second IDE
interface. Select “Disabled” to deactivate an interface if you are going to
install a primary and/or secondary add-in IDE interface.
The Choices: Enabled (default), OnChip, Disabled.

5.1.4 IDE Prefetch Mode
The “onboard” IDE drive interfaces supports IDE prefetching for faster drive
access. If the interface does not support prefetching. If you install a primary
and/or secondary add-in IDE interface, set this option to “Disabled”.
The Choices: Enabled (default), Disabled.

5.1.5 IDE Primary / Secondary Master / Slave PIO
The IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4) for
each of the IDE devices that the onboard IDE interface supports. Modes 0 through 4
provides successively increased performance. In Auto mode, the system automatically
determines the best mode for each device.
The Choices:Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4.

5.1.6 IDE Primary / Secondary Master / Slave UDMA
Ultra DMA/100 functionality can be implemented if it is supported by the IDE hard
drives in your system. As well, your operating environment requires a DMA driver
(Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and
your system software both support Ultra DMA/100, select Auto to enable BIOS
support.
The Choices: Auto (default), Disabled.

5.1.7 IDE HDD Block Mode
If your IDE hard drive supports block mode, select “Enabled” for automatic detection
of the optimal number of block read/ writes per sector the drive can support.
The Choices: Enabled (default), Disabled.

P4M80-M7 BIOS Manual
5.2 VIA OnChip PCI Device

If you highlight the literal “Press Enter” next to the “OnChip PCI Device” label and then
press the enter key, it will take you a submenu with the following options:

5.2.1

VIA-3058 AC97 Audio

This option allows you to control the onboard AC97 audio.
The Choices: Auto (default), Disabled.

5.2.2

VIA-3068 MC97 Modem

This option allows you to control the onboard MC97 modem.
The Choices: Auto (default), Disabled.

5.2.3

VIA-3043 OnChip LAN(Enabled)

This option allows you to control the onboard VIA-3043 OnChip LAN.
The Choices: Enabled (default), Disabled.

5.2.4

Onboard LAN Boot ROM

This item allows you to enable or disable the Onboard LAN Boot ROM
controller.
The Choices: Disabled (default), Enabled.

5.2.5

Onchip USB Controller

Select “Enabled” if your system contains a Universal Serial Bus (USB) controller and
you have USB peripherals.
The Choices:All Enabled (default).

5.2.6

On-chip EHCI Controller

This item allows you to enable or disable the on-chip EHCI controller.
The Choices: Enabled (Default), Disabled.

P4M80-M7 BIOS Manual
5.2.7

USB Emulation
Do not support any USB device on Dos
The Choices: Off, On (default).

5.2.8

USB Keyboard/ Mouse Support

This item allows you to enable or disable the USB Keyboard/ Mouse Legacy Support.
The Choices:Enabled (default), Disabled.

5.3 Super IO Device

If you highlight the literal “Press Enter” next to the “Super IO Device” label and then press
the enter key, it will take you a submenu with the following options:

5.3.1 Onboard FDC Controller

Select Enabled if your system has a floppy disk controller (FDC) installed on the system
board and you wish to use it. If install and FDC or the system has no floppy drive, select
Disabled in this field.
The Choices: Enabled (default), Disabled.

5.3.2 Onboard Serial Port 1
Select an address and corresponding interrupt for the first and second serial ports.
The Choices:Disabled, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto.

5.3.3 UART Mode Select
This item allows you to determine which Infra Red (IR) function of onboard I/O chip.
The Choices:Normal (default), AS KIR, IrDA.

P4M80-M7 BIOS Manual
5.3.4 UR2 Duplex Mode
elect the value required by the IR device connected to the IR port. Full-duplex mode
permits simultaneous two-direction transmission. Half-duplex mode permits
transmission in one direction only at a time.
The Choices: Half (default), Full.

5.3.5 Onboard Parallel Port
This item allows you to determine access onboard parallel port controller with which
I/O Address.
The Choices:378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.

5.3.6 Parallel Port Mode
The default value is SPP.
The Choices:
SPP(default) Using Parallel port as Standard Printer Port.
EPP
Using Parallel Port as Enhanced Parallel Port.
ECP
Using Parallel port as Extended Capabilities Port.
ECP+EPP
Using Parallel port as ECP & EPP mode.

5.3.7 ECP Mode Use DMA
Select a DMA Channel for the port.
The Choices: 3 (default), 1.

P4M80-M7 BIOS Manual
6 Power Management Setup
The Power Management Setup Menu allows you to configure your system to utilize energy
conservation and power up/power down features.

6.1 ACPI function
This item displays the status of the Advanced Configuration and Power Management
(ACPI).
The Choices: Enabled (default), Disabled.

6.2 Power Management Option
This category allows you to select the type (or degree) of power saving and is directly
related to the following modes:
1.HDD Power Down.
2.Suspend Mode.
There are four options of Power Management, three of which have fixed mode settings

Min. Power Saving
Minimum power management.
Suspend Mode = 1 hr.
HDD Power Down = 15 min

Max. Power Saving
Maximum power management only available for sl CPU’s.
Suspend Mode = 1 min.
HDD Power Down = 1 min.

P4M80-M7 BIOS Manual
User Define (default)
Allows you to set each mode individually.
When not disabled, each of the ranges are from 1 min. to 1 hr. except for HDD
Power Down which ranges from 1 min. to 15 min. and disable.

6.3 HDD Power Down
When enabled, the hard disk drive will power down and after a set time of system inactivity.
All other devices remain active.
The Choices: Disabled (default), 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7 Min, 8 Min,
9 Min, 10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15Min.

6.4 Suspend Mode
The item allows you to select the suspend type under ACPI operating system.
The Choices: Disabled (default), 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30
Min, 40 Min, 1 Hour.

6.5 Video Off Option
This field determines when to activate the video off feature for monitor power
management.
The Choices: Suspend→Off (default), Always on.

6.6 Video Off Method
This option determines the manner in which the monitor is goes blank.

V/H SYNC+Blank (default)

This selection will cause the system to turn off the vertical and horizontal
synchronization ports and write blanks to the video buffer.

Blank Screen

This option only writes blanks to the video buffer.

DPMS

Initial display power management signaling.
The Choices: Stop Grant, PwrOn Suspend.

6.7 Modem Use IRQ
This determines the IRQ, which can be applied in MODEM use.
The Choices: 3 (default),4 / 5 / 7 / 9 / 10 / 11 / NA.

6.8 Soft-Off by PWR-BTN
Pressing the power button for more than 4 seconds forces the system to enter the
Soft-Off state when the system has “hung.”
The Choices: Delay 4 Sec, Instant-Off (default).

P4M80-M7 BIOS Manual
6.9 Ac Loss Auto Restart
This field determines the action the system will automatically take when power is restored
to a system that had lost power previously without any subsequent manual intervention.
There are 3 sources that provide current to the CMOS area that retains these Power-On
instructions; the motherboard battery (3V), the Power Supply (5VSB), and the Power
Supply (3.3V). While AC is not supplying power, the motherboard uses the motherboard
battery (3V). If AC power is supplied and the Power Supply is not turned on, 5VSB from
the Power Supply is used. When the Power Supply is eventually turned on 3.3V from the
Power Supply will be used.
There are 3 options: “Former-Sts”, “On”, “Off”.
“Off” (default) Means always set CMOS to the “Off” status when AC power is lost.
“On” Means always set CMOS to the “On” status when AC power is lost
“Former-Sts” Means to maintain the last status of the CMOS when AC power is lost.
For example: If set to “Former-Sts” and AC power is lost when system is live, then after
AC power is restored, the system will automatically power on. If AC power is lost when
system is not live, system will remain powered off.

6.10 IRQ/Event Activity Detect

If you highlight the literal “Press Enter” next to the “IRQ/Event Activity Detect” label and
then press the enter key, it will take you a submenu with the following options:

6.12.1 PS2KB Wakeup Select

When select Password, please press Enter key to change password
with a maximum of 8 characters.
The Choices: Hot Key (default).

P4M80-M7 BIOS Manual
6.12.2 PS2KB Wakeup from S3/ S4/ S5
This item allows you to wake up from S3/ S4/ S5 with PS2 keyboard.
The Choices: Disabled (default), Ctrl+F1, Ctrl+F2. Ctrl+F3, Ctrl+F4,
Ctrl+F5, Ctrl+F6, Ctrl+F7, Ctrl+F8, Ctrl+F9, Ctrl+F10, Ctrl+F11,
Ctrl+F12, Power, Wake, Any Key.

6.12.3 PS2MS Wakeup from S3/ S4/ S5
This item allows you to wake up from S3/ S4/ S5 with PS2 keyboard.
The Choices: Disabled (default), Ctrl+F1, Ctrl+F2. Ctrl+F3, Ctrl+F4,
Ctrl+F5, Ctrl+F6, Ctrl+F7, Ctrl+F8, Ctrl+F9, Ctrl+F10, Ctrl+F11,
Ctrl+F12, Power, Wake, Any Key.

6.12.4 VGA
When set to On, any event occurring at a VGA Port will awaken a system which has
been powered down.
The Choices: Off (default), On.

6.12.5

LPT & COM

When this option is set to On, any event occurring at a COM(serial)/LPT (printer) port
will awaken a system which has been powered down.
The Choices: LPT/COM (default), COM, LPT, NONE.

6.12.6

HDD & FDD

When this option is set to On, any event occurring on a hard drive or a floppy drive
will awaken a system which has been powered down.
The Choices: On (default), Off.

6.12.7

PCI Master

When set to On, you need a LAN add-on card which supports the power function. It
should also support the wake-up on LAN jump.
The Choices: Off (default), On.

6.12.8

Power On by PCI Card

When you select Enabled, a PME signal from PCI card returns the system to Full ON
state.
The Choices: Disabled (default), Enabled.

6.12.9

Modem Ring Resume

This item allows you to disable or enable Modem Ring Resume.
The Choices: Disabled (default), Enabled.

6.12.10 RTC Alarm Resume
When “Enabled”, you can set the date and time at which the RTC
(real-time clock) alarm awakens the system from Suspend mode.
The Choices: Enabled, Disabled (default).

P4M80-M7 BIOS Manual
6.12.11 Date (of Month)
You can choose which month the system will boot up. This field is only
configurable when “RTC Resume” is set to “Enabled”

6.12.12 Resume Time (hh:mm:ss)
You can choose the hour, minute and second the system will boot up.
This field is only configurable when “RTC Resume” is set to “Enabled”.

6.12.13 IRQs Activity Monitoring

Press Enter to access another sub menu used to configure the different wake up events (i.e.
wake on LPT & COMM activity).
Primary INTR
On
IRQ3 (COM2)
Enabled
IRQ4 (COM1)
Enabled
IRQ5 (LPT2)
Enabled
IRQ6 (Floppy Disk)
Enabled
IRQ7 (LPT1)
Enabled
IRQ8 (RTC Alarm)
Disabled
IRQ9 (IRQ2 Redir)
Disabled
IRQ10 (Reserved)
Disabled
IRQ11 (Reserved)
Disabled
IRQ12 (PS/2 Mouse)
Enabled
IRQ13 (Coprocessor)
Enabled
IRQ14 (Hard Disk)
Enabled
IRQ15 (Reserved)
Disabled

P4M80-M7 BIOS Manual
7 PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI, or Personal Computer
Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of
the CPU itself uses when communicating with its own special components. This section
covers some very technical items and it is strongly recommended that only experienced
users should make any changes to the default settings.

7.1 PNP OS Installed
When set to YES, BIOS will only initialize the PnP cards used for the boot sequence (VGA,
IDE, SCSI). The rest of the cards will be initialized by the PnP operating system like
Window™ 95. When set to NO, BIOS will initialize all the PnP cards. For non-PnP
operating systems (DOS, Netware™), this option must set to NO.
The Choices: No (default), Yes.

7.2 Reset Configuration Data
The system BIOS supports the PnP feature which requires the system to record which
resources are assigned and protects resources from conflict. Every peripheral device has a
node, which is called ESCD. This node records which resources are assigned to it. The
system needs to record and update ESCD to the memory locations.
These locations (4K)
are reserved in the system BIOS. If the Disabled (default) option is chosen, the system‘s
ESCD will update only when the new configuration varies from the last one. If the Enabled
option is chosen, the system is forced to update ESCDs and then is automatically set to the
“Disabled” mode.
The above settings will be shown on the screen only if “Manual” is chosen for the resources
controlled by function.

P4M80-M7 BIOS Manual
Legacy is the term, which signifies that a resource is assigned to the ISA Bus and provides
non-PnP ISA add-on cards. PCI / ISA PnP signifies that a resource is assigned to the PCI
Bus or provides for ISA PnP add-on cards and peripherals.
The Choices: Disabled (default), Enabled.

7.3 Resources Controlled By
By Choosing “Auto(ESCD)” (default), the system BIOS will detect the system resources
and automatically assign the relative IRQ and DMA channel for each peripheral.By
Choosing “Manual”, the user will need to assign IRQ & DMA for add-on cards. Be sure
that there are no IRQ/DMA and I/O port conflicts.

7.4 IRQ Resources
This submenu will allow you to assign each system interrupt a type, depending on the type
of device using the interrupt. When you press the “Press Enter” tag, you will be directed to
a submenu that will allow you to configure the system interrupts. This is only
configurable when “Resources Controlled By” is set to “Manual”.
IRQ-3
IRQ-4
IRQ-5
IRQ-7
IRQ-9
IRQ-10
IRQ-11
IRQ-12
IRQ-14
IRQ-15

assigned to
assigned to
assigned to
assigned to
assigned to
assigned to
assigned to
assigned to
assigned to
assigned to

PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device

7.5 PCI / VGA Palette Snoop
Choose Disabled or Enabled. Some graphic controllers which are not VGA compatible
take the output from a VGA controller and map it to their display as a way to provide boot
information and VGA compatibility.
However, the color information coming from the VGA controller is drawn from the palette
table inside the VGA controller to generate the proper colors, and the graphic controller
needs to know what is in the palette of the VGA controller. To do this, the non-VGA
graphic controller watches for the Write access to the VGA palette and registers the snoop
data. In PCI based systems, where the VGA controller is on the PCI bus and a non-VGA
graphic controller is on an ISA bus, the Write Access to the palette will not show up on the
ISA bus if the PCI VGA controller responds to the Write
In this case, the PCI VGA controller should not respond to the Write, it should only snoop
the data and permit the access to be forwarded to the ISA bus. The non-VGA ISA graphic
controller can then snoop the data on the ISA bus. Unless you have the above situation,
you should disable this option.
Disabled (default)
Disables the function.
Enabled
Enables the function.

P4M80-M7 BIOS Manual
7.6 Assign IRQ For VGA
This item allows the users to choose which IRQ to assign for the VGA.
The Choices: Enabled (default), Disabled.

7.7 Assign IRQ For USB
This item allows the users to choose which IRQ to assign for the USB.
The Choices: Enabled (default), Disabled.

P4M80-M7 BIOS Manual
8 PC Health Status

8.1 Shutdown Temperature
This item allows you to set up the CPU shutdown Temperature. This item only effective
under Windows 98 ACPI mode.
The Choices: Disabled (default), Enabled.

8.2 CPU FAN Control by
The Choice “smart” can make your CPU FAN to reduce noise.
The Choices: SMART (default), Always On.

8.3 CPU Vcore +3.3V, +5.0V, DRAM Voltage , AGP Voltage ,Voltage Battery
Detect the system’s voltage status automatically.

8.4 Current CPU Temp
This field displays the current temperature of CPU.

8.5 Current CPU FAN Speed
This field displays the current speed of CPU fan.

8.6 Current SYS FAN Speed
This field displays the current speed SYSTEM fan.

P4M80-M7 BIOS Manual
8.7 Show H/W Monitor in POST
If you computer contain a monitoring system, it will show PC health status during POST
stage. The item offers several delay time to select you want.
The Choices: Enabled (default), Disabled .

8.8 Chassis Open Warning
This item allows you to enable or disable Chassis Open Warning beep.
The Choices: 60O C/140OF, 65O C/149O F, 70OC/158O F, Disabled (default).

P4M80-M7 BIOS Manual
9 Frequency/ Voltage Control

9.1 CPU Clock Ratio
The Choices: 8X (default), 9X, 10X, 11X, 12X, 13X, 14 X, 15X, 16X, 17X,
18X, 19X, 20 X, 21 X, 22 X, and 23X.

9.2 CPU Voltage Regulator
This item allows you to select CPU Voltage Control.
The Choices: Default (default)

9.3 DDR Voltage Regulator
This item allows you to select DDR Voltage Control.
The Choices: Default,2.65V (default)

9.4 AutoDetect PCI/DIMM Clk
This item allows you to enable / disable auto Detect PCI Clock.
The Choices: Enabled (default), Disabled.

9.5 Spread Spectrum(Enabled)
This item allows you to enable/disable the Spread Spectrum function.
The Choices: Enabled (default), Disabled

P4M80-M7 BIOS Manual
9.6 CPU CLOCK
This item allows you to select CPU Clock, and CPU over clocking.
The Choices: 100MHZ (default).
Special Notice:
If unfortunately, the system’s frequency that you are selected is not
functioning, there are two methods of booting-up the system.
Method 1:
Clear the COMS data by setting the JCOMS1 ((2-3) closed)) as “ON”
status. All the CMOS data will be loaded as defaults setting.
Method 2:
Press the key and Power button simultaneously, after that
keep-on pressing the key until the power-on screen showed.

This action will boot-up the system according to FSB of the processor
.
It’s strongly recommended to set CPU Vcore and clock in default setting. If the
CPU Vcore and clock are not in default setting, it may cause CPU or M/B damage.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2006:05:22 09:58:59Z
Modify Date                     : 2007:06:20 15:51:39+08:00
Page Count                      : 67
Creation Date                   : 2006:05:22 09:58:59Z
Mod Date                        : 2007:06:20 15:51:39+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : B93051 (Christine)
Metadata Date                   : 2007:06:20 15:51:39+08:00
Creator                         : B93051 (Christine)
Title                           : Microsoft Word - P4M80M7&M7A_V80_0227C.doc

EXIF Metadata provided by EXIF.tools

Biostar P4M800 M7 Owners Manual P4M80M7&M7A_V80_0227C

Navigation menu

Versions of this User Manual:

Views

Navigation