BlackBox Biometrics BG710 Blast Gauge System User Manual

BlackBox Biometrics Inc. Blast Gauge System

User Manual rev1

Download: BlackBox Biometrics BG710 Blast Gauge System User Manual
Mirror Download []BlackBox Biometrics BG710 Blast Gauge System User Manual
Document ID3118704
Application ID2rgU6IxwnrLBUa35XBhxdQ==
Document DescriptionUser Manual rev1
Short Term ConfidentialNo
Permanent ConfidentialNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize38.7kB (483759 bits)
Date Submitted2016-08-31 00:00:00
Date Available2016-09-01 00:00:00
Creation Date2016-08-30 15:01:12
Producing SoftwareMicrosoft® Word 2013
Document Lastmod2016-08-30 15:01:12
Document Title¬
Document CreatorMicrosoft® Word 2013
Document Author: Joe Bridgeford

Quick Start Guide
A: Install software from, DVD, or SD card.
B: Open the Blast Gauge Data Retrieval System and select
on the top navigation bar.
C: Connect your Blast Gauge(s) to your PC via USB. Connected gauge(s) will appear on the “Gauges
Connected” sidebar. Initially, the software will display “Gauge Attached…Scanning” message. Once
gauge(s) is (are) ready for set-up, this will be replaced with “Gauge Attached…Ready.”
D: Set-up gauge(s).
i. Select a profile based on mounting location. Note: Only select “Personnel” if the gauge will
be worn directly on a person.
ii. If needed, unlock and change the pressure threshold values (advanced users only).
125 Tech Park Drive Rochester, NY 14623
iii. EDI-PI will be auto-filled with the ID number from your CAC Card. If you’re not using a
CAC Card Reader, manually enter identifying information.
iv. Select the state of gauge(s) after setup. Note: Gauge(s) must be “On” to record events.
v. Select
. Gauge(s) are ready for use and can be disconnected
from PC when software displays “Gauge Attached…Ready.”
After an event has been recorded:
When ready to download event data to PC, open software and select
Connect gauge(s) to PC via USB and data will be automatically downloaded by the software.
125 Tech Park Drive Rochester, NY 14623
FCC § 15B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
Cet appareil est conforme à la partie 15 des règles de la FCC. Le fonctionnement est soumis aux deux conditions suivantes: (1) ce
dispositif ne peut pas causer d'interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les
interférences qui peuvent causer un mauvais fonctionnement.
FCC § 15.21
Changes or modifications made to this equipment not expressly approved by BlackBox Biometrics Inc. could void the user's authority
to operate the equipment.
FCC § 15.105
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
FCC and IC Radiation Exposure Statement:
This portable equipment with its antenna complies with FCC’s and IC’s RF radiation exposure limits set forth for an uncontrolled
environment. To maintain compliance, follow the instructions below:
1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment.
FCC et IC exposition aux radiations:
Cet équipement portable avec son antenne est conforme aux limites d'exposition aux rayonnements RF de la FCC et IC de définies
pour un environnement non contrôlé. Pour maintenir la conformité , suivez les instructions ci-dessous:
1. Cet émetteur ne doit pas être situé ou opérant en conjonction avec une autre antenne ou émetteur.
2. Éviter tout contact direct à l'antenne , ou garder le contact à un minimum tout en utilisant cet équipement .
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme aux CNR exempts de licence d'Industrie Canada. Le fonctionnement est soumis aux deux conditions
(1) Ce dispositif ne peut causer des interférences; et
(2) Cet appareil doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement
de l'appareil.
Intended use of the equipment:
Measure exposure to blast overpressure
Technical specification:
Size each Blast Gauge
44.0 x 22.0 x 36.0 mm
Weight each Blast Gauge
43.7 g
Pressure Measurement Range 0.5-110 psi
Pressure Resolution
± 0.05 psi
3 axis Acceleration
± 200 g
Bluetooth® 4.0 LE (BLE)
BLE Range
Under ideal conditions: 2m for BGSM and 10 meters for BGSA
Data Interface PC:
USB (micro B connection)
Data Retrieval System
Custom Graphic User Interface and database accommodates data
download, firmware upgrades, and configuration.
Event Storage Capacity
250 events @ 20ms per event
Operating range
-20°C to +60°C
400 psi, 400 g
125 Tech Park Drive Rochester, NY 14623
Water and Dust Resistance
Precautions for Safe Handling:
The Blast Gauge® System has been designed and manufactured for use by qualified personnel for measuring exposures to blast
Safety considerations are contained in the Blast Gauge System Safety Data Sheet dated February 10, 2016 included in the package
Shelf life is greater than 5 years in cool (15 ºC - 25ºC), dry and ventilated areas, which are subject to little temperature change. Do not
place the article near heating equipment, nor expose to direct sunlight for long periods. Elevated temperatures can result in
shortened battery life and degrade performance.
This Product contains a lithium battery that is not rechargeable or replaceable. Normally the article has no odor. Under normal
conditions of use, the battery, its electrode materials and its hazardous liquid electrolyte are non-reactive provided the battery
integrity is maintained. The battery will release a pungent corrosive odor if leaking.
There are no federal regulations for disposal of lithium batteries. Individual states or localities establish their own guidelines for
battery disposal, and should be contacted for any disposal guidelines that they may have for a lithium battery housed in the Blast
125 Tech Park Drive Rochester, NY 14623

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Language                        : en-US
Tagged PDF                      : Yes
Title                           : ¬
Author                          : Joe Bridgeford
Creator                         : Microsoft® Word 2013
Create Date                     : 2016:08:30 15:01:12-04:00
Modify Date                     : 2016:08:30 15:01:12-04:00
Producer                        : Microsoft® Word 2013
EXIF Metadata provided by
FCC ID Filing: 2AHN8BG710

Navigation menu