Bling Lighting Technologies BL-BUFI Deng WiFi-BUFI bulb lamp User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3338910
Application ID	NcbamkSEbj3Y10wEXOhJoA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.54kB (281738 bits)
Date Submitted	2017-03-30 00:00:00
Date Available	2017-03-30 00:00:00
Creation Date	2016-12-27 10:28:09
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2016-12-27 10:28:09
Document Title	Users Manual
Document Creator	CorelDRAW
Document Author:	Administrator

Deng
Installation
Deng
Installation
1.Connect the Encoder with any LAN port of router via network cable, and the other end
with AC power supply.
How to set up WiFi Name and Password
Use Directions
2. Install the bulb lamp in any E27 lamp holder,then turn on power then connect to
the WiFi release from the BUFI and enjoy the Lag-free game and HD videos freely.
1.Open the browser and imput 192.168.31.1, press the Enter key enter the login
interface. Input the User Name: admin, Password: admin, press login.
How to modify the IP Address
FAQ
Features
,enter into Interface .
1.Click Network
Ask:BUFI bulb lamp can be used in the Power Strip? Will be interfered by other
electrical signals?
In order to get a better Internet experience, it is recommended to plug the
encoder and bed lamp to the wall plug or AC power directly, and avoid to use
the high power appliances such as blower, microwave oven and charger etc.
* Note: Non-professionals do not arbitrarily modify the data, this situation only when the device exists IP conflict operation!
ON/OFF mode
Status
192.168.31.1
1.Lamp ON + WiFi ON (turn on the switch);
System
Network
Logout
Interface
WiFi
Authorization Required
Please input your user name and password.
Firewall
2.Click LAN to modify .
No flicker
Router
100-240V 50- 60Hz
User Manual
User Name
admin
Password
admin
2.Lamp OFF WiFi ON (turn on the switch, then turn off/on continuously 3s later);
Login
2.Click Network
Status
Connect
Edit
Delete
Connect
Stop
Edit
Delete
WANG
Connect
Stop
Edit
Delete
Stop
System
, enter into WiFi interface, and click the modifying item.
Network
100-240V 50-60Hz
3. In the General Setup IPv4 address for IP address modification,
modify and click Save & Apply to take effect.
Logout
Interface
WiFi
Interfaces-LAN
Firewall
Common Configuration
General Setup
SSID
Disable
Edit
Advanced Settings
Physical Settings
Firewall Settings
Remove
E27 port
Network
Cable
192.168.31.1
Ipv4 Address
* Modify WiFi Name
Save & Apply
Interface Configuration
General Setup
Wireless Security
ESSID
Bling
Save & Apply Save Reset
1.Click System, choose Administration .
Status
Basic Parameters
Color Temperature: 2700K-6500K
Waterproof Rating :IP20
Luminance Flux: 300lm
Rated Input: 100-240V-50/60Hz 0.09A
Dimension: Φ57*125mm
Rated Power:7W
Weight: 1300g
Work Temperature: -25 - + 45℃
Service Life: 20000 hours
SSID: 192.168.31.1
System
Network
Cautions
Logout
1.Please use the product with the rated voltage;
System
2.Do not attempt to dismount or repair the product for avoiding damage;
General Setup
* Correctly install and use the BUFI bulb lamp according to the above method to
enjoy your journey of fast Internet access.
Encoder
3.Keep away from water for avoiding product damage;
Backup/Flash
Interface Configuration
Wireless Security
Reboot
Encryption
WPA2-PSK
auto
2.Setup the password, confirm the password, click Save & Apply to take effect.
5.Do not cover the bulb lamp with cloth and quilt for avoiding affect heat dissipation.
Password
Password
Save & Apply Save
Reset
Ask: How to recover the BUFI bulb lamp to default settings?
Use a pin to hold down the Reset button of the bed lamp for over 8s to recover
the bulb lamp to default settings. After resetting, your personal data will be
cleared since it will also be reset , please be cautious when using this function. If
it has recovered default settings, please configure according to the above steps.
Warranty Terms
Commitments on after service of the BUFI bulb lamp:
Within the warranty period, the product fault which is not caused by manmade damage may enjoy the
following “Three-Guarantee” services
1.Within 7 days after you have received the product, if BUFI bulb lamp has the
performance faults which are listed in the “BUFI bulb lamp Commodity
Performance Fault List”, after tested and confirmed by our After Service
Center, you may select to return or replace the product of the same model
without any charge;
2.Within 8-15 days after you have received the product, if BUFI bulb lamp has
the performance faults which are listed in the “BUFI bulb lamp Commodity
Performance Fault List”, after tested and confirmed by our After Service
Center, you may select to replace the product of the same model or require
repair service without any charge;
3.Within 12 months after you have received the product, if BUFI bulb lamp has
the performance faults which are listed in the “BUFI bulb lamp Commodity
Performance Fault List”, after tested and confirmed by our After Service
Center, the product enjoys free repair services.
Non-Warranty Terms
The product shall not enjoy “Three-Guarantee” services for the followings (including but not
limiting to):
1.Without “Three-Guarantee” voucher or valid invoice, or the product has
expired the “Three-Guarantee” services;
2.The product is not used, maintained and stored according to the User
Manual;
3.The product is damaged caused by fire, flood, lightning strike and force
majeure;
4.The model or code listed on the Warranty Voucher is not accordant with the
real product;
5.The normal decoloring, wear and consumption of the product are not covered
in the warranty service.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
Ask: The WiFi signal is transmitted via power circuit, if the neighbor can receive
the signal from the power circuit?
Impossible, the network signal only transmit under the same ammeter to provide
the safe, stable and fast network.
4.Keep away from high temperature and fire source;
MAC-Filter
Algorithm
Ask: The indicator of BUFI bulb lamp keeps on but can't access Internet, what
shall I do?
1.Make sure the encoder is properly connected with the LAN port of the router.
2.Make sure that your phone and notebook can access Internet normally when
connecting with the WiFi of router.
Ask: Can the BUFI bulb lamp be used in the factory, office and hotel?
It is not suggested because most factories and offices adopt 3-phase power
supply, it is difficult to keep the encoder and the BUFI bulb lamp at the same
phase, the hotel has complicated power circuit, and it is difficult to keep the
encoder and the BUFI bulb lamp under the same ammeter.
Administration
Thank you for selecting DengWiFi-BUFI bulb lamp series, this product is the new
generation and intelligent household product by adopting advanced LED lighting and
intelligent communication technology, and is capable of providing perfect lighting
experience and fast and stable WiFi as the perfect intelligent product to solve the
network coverage issue for the intelligent household product in the future.
Low luminance decay
Ask: What can I do if I browse 192.168.31.1 but can't enter the Web management
interface?
1.Make sure your phone or computer is connected with the WiFi of bulb lamp and
has obtained the IP address.
2.Try to cut off supply and reboot the router and encoder, connect the bulb lamp
and access “192.168.31.1” again.
How to modify the Administrator Password
MAC-Filter
* Modify WiFi Password-not less than 8 letters (it is recommended to use WPA-PSK
or WPA2-PSK encryption)
Please read the User Manual carefully before operating this product.
Low power consumption
Reset
E27 lamp holder
3.Lamp OFF + WiFi OFF (turn off the switch);
LAN
WAN
No radiation
FCC INFORMATION
Warranty Voucher
Confirmation
Save & Apply
Ask: Can the product only be used for one encoders? What shall I do if several
rooms are covered with WiFi?
One encoder can be used for 6 LAFI bed lamp or BUFI bulb, which means you
only need to purchase one encoder for 6 LAFI bed lamps.
* This Warranty Voucher is only applicable to the China region.
10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
Create Date                     : 2016:12:27 10:28:09+08:00
Modify Date                     : 2016:12:27 10:28:09+08:00
Producer                        : Corel PDF Engine Version 14.0.0.701
Author                          : Administrator
Creator                         : CorelDRAW
Title                           : 球泡灯说明书(对照x4)

EXIF Metadata provided by EXIF.tools