Blue Bamboo P10 Printer User Manual P10 QIG EN 3501890 v6

Blue Bamboo (HK) Limited Printer P10 QIG EN 3501890 v6

User manual

Paper
Microsoft usb
Packing List
Installation Guide
P10 Printrer
Quick Installation Guide
Load Paper Charge printer
Bluetooth LED Status Code
Power Key
Funtion Key
Feed Key
Light guide
Part List
LED Error Code Caution&
FCC/CE Statement
Constantly lit
Flashing
Constantly lit
Constantly lit
Off
Flahsing
together
Bluetooth module
available
Data transaction
Via Bluetooth
Power on
normal status
Charging
Charging finished
An error has occurred
(see Error Code)
Out of paper
A transmission
error occurred
Print head
overheated
Battery voltage
is too low
Add paper
Check the
tansmission
status
Wait untill the
print head
cools down
Recharge the
battery
FCC Compliance Statement
“This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
ࠉ Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
WARNING:
'RQRWGLVDVVHPEOHWKH3ULQWHUEDWWHU\
Only qualified technicians may service the device.
'RQRWXVH3ULQWHUQHDUZDWHU
1. Use desk and mobile PC USB port connect into
micro USB of the printer
2. When charging the LED will be red, when the
battery is fully charged, the LED will turn off.
Note: Don’t provide AC adapter for P10
Insert plug here
Device name and PIN
Ɣ'HYLFHQDPHDQG3,1ODEHOFDQEHIRXQGXQGHU
the paper roll
Discovery Modes (factory set)
Ɣ$OZD\V$OZD\VGLVFRYHUDEOH
ƔVW&RQQHFW'LVFRYHUDEOHXQWLOVWFRQQHFWLRQ
is established
Ɣ0RGH.H\3UHVV0RGH.H\WRPDNHGLVFRYHUDEOH
for 90 seconds
Using with Apple devices
Ɣ3UHVV0RGH.H\WZLFHWRGLVFRQQHFWDQGSUHVV
twice again to reconnect
Ɣ%OXH/('ZLOOIODVKZKHQFRQQHFWLQJGLVFRQQHFWLQJ
from Apple devices
Ɣ6XSSRUWVL26DQGKLJKHU
FCC Compliance Statement
Increase the separation between the equipment and
receiver.
ࠉ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
ࠉ&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79
technician for help.
RF warning statement:
The device has been evaluated to meet general RF
exposure requirement. The device can be used in
portable exposure condition without restriction.
EU Regulatory Conformance
(XURSH577(
&RPSOLDQFH6WDWHPHQW+HUHE\%OXH%DPERR
declares that this　equipment complies with the
essential requirement and other relevant provision
RI'LUHFWLYH(&2)7+((8523($1
3$5/,$0(17$1'7+(&281&,/RI0DUFK
1999 on radio equipment and telecommunication
terminal equipment and the mutual recognition of
WKHLUFRQIRUPLW\577(
CE NB Mark:
For warranty period,repair and service issues,please
contant your distributor:
Caution&
FCC/CE Statement

Navigation menu