Blue Bamboo P200 P200 User Manual Rev2

Download:
Mirror Download [FCC.gov]
Document ID	1686162
Application ID	wP2RN1mTLe49rfHFEqnrbg==
Document Description	User Manual_Rev2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	111.05kB (1388107 bits)
Date Submitted	2012-04-30 00:00:00
Date Available	2012-05-01 00:00:00
Creation Date	2012-03-22 13:22:00
Document Lastmod	2012-03-22 13:22:00
Document Title	User Manual_Rev2

Front
Packing List
Paper Cutter
Status LED
Printer
Paper
MSR
Power Jack
Power
Button
Serial Port
USB Port
Cancel Key
Clear Key
Enter Key
Navigation
Key
1A Power Adapter
(3A optional)
Battery
Back
Menu Key
Battery
Cover
Numeric Keypad
Feed Button
Contact your distributor for replacement parts
Load Paper
Install Battery
1. Open the lid.
2. Install paper roll with paper pointing up.
3. Pull out a small amount of paper, close lid.
1. Remove the battery cover.
2. Plug in the battery cable into the connector.
3. Install the battery into the slot and install the
battery cover.
Battery
Connector
Power & Charging
1. Insert the DC plug of power adapter* into
the power jack of printer.
2. Plug power adaptor into AC power outlet.
Install SAM Card
1. Remove the battery cover and battery.
2. Open the card holder and insert the SAM card
with the electronic chip facing down and the
cut-out corner on top.
3. Close the card holder and lock it into
place.
4. Install the battery and the battery cover.
Power
Jack
SAM Slot
*Optional 3Amp power supply required when running without battery.
Smart Card
Position the smart card and insert it into the
smart card reader slot with the chip facing
down.
MSR
1. Position the card with the magnetic stripe
facing down and towards the printer.
2. Swipe it through the reader in either direction.
FCC Statement
FCC ID: UWJP200
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
PART 15.21 STATEMENT
(3) Changes or modifications not expressly approved
by the party responsible for compliance could void
the user's authority to operate the equipment.
(4) For receivers and Class B digital This product has
been tested and complies with the specifications for
a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which is found by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
· Reorient or relocate the receiving antenna
· Increase the separation between the equipment or
devices
· Connect the equipment to an outlet other than the
receiver's
· Consult a dealer or an experienced radio/TV
technician for assistance
Bluetooth
The P200 printer can communicate with
other Bluetooth SPP compatible devices,
such as peripheral equipment PDAs, mobile
phones, and computers. Confirm that your
host device supports the SPP (Serial Port
Profile) before using the P200 printer.
Bluetooth communication distance is up to
10m.
Operating Temperature:
0~40°C (+32° to 104°F)
Default Device Name: P200
Default PIN Code: 1234
Storage Humidity:
10~90%, no condensation
CE Statement
Caution
Europe-R&TTE Compliance Statement
WARNING:
Hereby, Blue Bamboo declares that this
equipment complies with the essential
requirement and other relevant provision
of Directive 1999/5/EC OF THE
EUROPEAN PARLIAMENT AND THE
COUNCIL of march 9,1999 on radio
equipment and telecommunication
terminal Equipment and the mutual
recognition of their conformity(R&TTE).
• Do not disassemble the Printer, battery
or AC adapter. Only qualified technicians
may service the device.
CE NB Mark:
1588
Environment
• Do not use batteries, AC adapters or
Printer near water.
Operating Humidity:
20~85%, no condensation
Storage Temperature:
-20~60°C (-4° to 140°F)
For warranty period, repair and service
issues, please contact your distributor:

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Modify Date                     : 2012:03:22 13:22+08:00
Create Date                     : 2012:03:22 13:22+08:00
Metadata Date                   : 2012:03:22 13:22+08:00
Format                          : application/pdf
Document ID                     : uuid:9e91392a-3131-4dc5-893a-6e9b50482493
Instance ID                     : uuid:d0ce9d19-0a8b-4267-a6a4-9ebfa83118aa
Has XFA                         : No
Page Count                      : 2

EXIF Metadata provided by EXIF.tools