Blue Ocean Innovation RECHAR304 JTECH PAGER User Manual 321045B2 QuikCall Pagers

Blue Ocean Innovation Limited JTECH PAGER 321045B2 QuikCall Pagers

Users Manual

Pager and Charger Guide Part Number 321045B5 Premises Pager System® QuikCall™ Pagers
2 Introduction: Congratulations on your purchase of a JTECH Paging System. Please take a few minutes to review this manual prior to installing and operating your system. Please inspect the System upon receipt. If the contents appear to be damaged, notify the shipper immediately to file a claim and notify JTECH Customer Care. If any component is missing, please contact JTECH Customer Care. If you have any questions or need assistance, please call JTECH Customer Care at 800-321-6221 or 561-997-0772, option 6. Pager Certifications: FCC statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment. RSS-Gen & RSS-210 statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RSS-102 Statement: "This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. " "Cet équipement est conforme à l'exposition aux rayonnements Industry Canada limites établies pour un environnement non contrôlé. Pager Dimensions and Weights: Pager (Without Clip)  LxWxH 1.0x 2.2x 3.1” (33x56x79mm)  Weight 2.2oz (63gm) Pager (With Metal Clip):  LxWxH 1.4x 2.2x 3.1” (35x56x79mm)  Weight 2.8oz (80gm) Pager Dimensions and Weights Certifications Introduction H W L L W H
3 Pager (With Spring Clip):  LxWxH 1.4x 2.2x 3.8” (35x56x97mm)  Weight 2.6oz (74gm) Pager (With Promotional Paddle And Inserts):  LxWxH 1.2x 2.2x 7.7” (31x56x196mm)  Weight 4.4oz. (124gm) Charger Dimensions and Weight Charger Only  LxWxH 13.5x 4.8x 2.6” (343x122x65mm)  Weight 1.64lbs (0.75kg) Charger and 10 Pagers With Clips:  LxWxH1 13.5x 4.8x 4” (343x122x102mm)  Weight 3.41lbs (1.55kg) Charger and 10 Pagers With Promotional Paddles:  LxWxH2 13.5x 4.8x 8.8” (343x122x224mm)  Weight 4.38lbs (1.99kg) Charger Components: 2.4 A Power Adapter Jumper Wires (Optional Equipment) AC Power Cord H W L JTECH H W L 10 Position Charger W L H1 H2 H Charger Components Define what transmitter is to be used. Note:
4 Power Adapter Plug Charger Jack Connecting Power: 1. Insert the Power Adapter plug into jack on the bottom of the Charger. 2. Feed the wires through the guides in the bottom of the Charger. 3. Connect the Power Adapter to the AC Power Cord. 4. Plug the AC Power Cord into a 110-240VAC outlet. 5. The green LED on the Charger will light (ON). 6. Once the Charger is powered (ON), the Pagers can be inserted. Mounting Chargers:  Chargers can be wall, shelf or counter top mounted.  Mounting hardware is user supplied. Mounting Chargers Connecting Power to Chargers
5 Combining Chargers: If two Chargers are to be used, they can be combined with one 2.4A Power Supply. To combine: 1. Use a screwdriver or similar tool to extend the metal tabs out from one of the Chargers. 2. Place both Chargers on a table and slide together. The metal tabs will lock both Chargers together. 3. Insert the Power Adapter plug into jack on the bottom of the Charger. 4. Use the Jumper Wire (optional) to connect both Chargers together. 5. Feed the wires through the guides in the bottom of the Charger. 6. Connect the Power Adapter to the AC Power Cord. 7. Plug the AC Power Cord into a 110-240AC outlet. 8. The green LED on the Charger will light (ON). 9. Once the Charger is powered (ON), the Pagers can be inserted. Combining Chargers Power Adapter Plug Charger Jack
6 Charging Pagers:  Pagers are turned OFF during shipment from JTECH.  When first received, Pagers must be charged for a minimum of 3 hours prior to use. This first charge will also turn ON the Pagers for use.  The charging system is two stage, with a fast initial and then final maintenance charge.  Charging Pagers: 1. Insert Pagers into the empty locations of a powered (ON) Charger. 2. Each Pager’s LED will light. 3. The LED color indicates charging condition.  Flashing yellow light = Battery charge very low. Charge needed. Do not use the Pager.  Solid yellow light = Charge needed.  Solid green light = OK to use. 4. Pagers in use and returned to the Charger within 24 hours will fully charge within three hours. 5. If not returned within 24 hours, charging time of up to 8 hours may be required to fully charge batteries. 6. When not in the Charger, each Pager continues to indicate battery charge condition:  Flashing yellow light = Charge needed.  Flashing green light = OK to use. Charging and Storing Pagers:  To maintain maximum battery capacity, store Pagers in the powered (ON) Charger.  If Pagers are left uncharged for more than 4 days, it is recommended to disconnect the batteries until their next use. See “Replacing the Battery” on page 11 for instructions.  If left uncharged for extended periods of time, Pager batteries can damage beyond repair and will need to be replaced.  When charged and stored properly, a battery life of 18-24 months can be expected before replacement is suggested. Charging and Storing Pagers Connecting Power to Chargers
7 Paging Using a Desktop Controller: 1. Remove a Pager from the Charger. 2. The Pager will vibrate and it’s LEDs will flash to confirm it is ready for use. 3. The Pager charge LED will continue to flash, confirming the it is ready to receive a page. 4. Enter the number of the Pager on the Controller. 5. Press # or SEND button to send the page. 6. The XMIT light on the Controller will turn ON, confirming the page is being sent. 7. The Pager will vibrate, tone or flash as required. 8. See “Enter Pager #” Menu instructions in your Desktop Controller manual for more information. Paging Using a Desktop Controller
8 Paging Using a Kitchen Controller or Expeditor Panel: 1. Remove the Pager you wish to page from the Charger. 2. The Pager will flash and vibrate to confirm it is ready for use. 3. The Pager charge LED will continue to flash, confirming it is ready to receive a page. 4. Press the number on the Controller or Expeditor Panel of the Pager. 5. The light on the panel, next to that number will turn ON. 6. The XMIT light will turn ON for 2-3 seconds and turn off. 7. The Pager will receive a single, one second vibration (factory setting). 8. The light on the panel, next to that Pager number will continue to stay ON for 40 seconds (factory setting). 9. If a Controller and Expeditor Panel are combined, pressing a button on either panel will light both panels. 10. After 40 seconds (factory setting), the light next to the number pressed will begin to blink on the Panel or Panels for an additional 40 seconds (factory setting), before turning off. 11. See Paging instructions in your Kitchen Controller manual for more information. Paging Using a Kitchen Controller or Expeditor Panel
9 Paging Using a Desktop Controller and Telephone: (Telco Module must be installed) 1. Remove the Pager you wish to page from the Charger. 2. The Pager will flash and vibrate to confirm it is ready for use. 3. The Pager charge LED will continue to flash, confirming it is ready to receive a page. 4. Pick up the phone and listen for the dial tone. 5. Dial the phone number that has been assigned to the TELCO Module installed. 6. Listen for a voice message from the telephone that confirms the Controller is ready. 7. Within 8-10 seconds, using the telephone keypad, enter the Pager number (up to 4 digits) and press the # button to send the page. 8. A voice message heard on the phone confirms the message was sent. 9. Hang up the telephone. 10. The Pager will receive a single, one second vibration (factory setting). 11. See Paging instructions in your Desktop Controller manual for more information. Paging Using a IntelFlex Desktop Controller with Telco Module
10 Replacing the Clip :  There are 3 Clip attachments; Metal, Spring or Paddle.  To replace a Clip or Paddle: 1. Turn the Pager over. 2. Push or pull the small plastic tab as shown in below and slide the Clip or Paddle off. 3. Slide the new Clip or Paddle on until a “click” can be heard, locking the clip or paddle onto place. Metal Clip: Spring Clip: Paddle: Replace The Clip 5 JTECH JTECH JTECH 5 Push Tab Push Tab Pull Tab Slide Slide Slide
11 Loosen Replacing the Insert: 1. Turn the Pager over. 2. Using a flat blade screwdriver or equivalent to unlock the clear plastic cover. 3. Slide the clear plastic cover out. 4. Remove the Insert. 5. Replace with a new Insert. 6. Replace and slide the clear plastic cover into place. When inserted completely, the cover will “snap” into place. 7. Replace and tighten the screw (do not over tighten). Inserts:  Inserts can be professionally printed (call your JTECH sales representative for more details).  Material thickness is 0.020” (5.1mm) maximum. Replacing the Battery: 1. Batteries that no longer charge properly or have a reduced operating time can be replaced by the user. 2. If using a Spring Clip, it must be removed to access the battery door screw. 3. Use a #1 Philips screwdriver to remove the screw. 4. Slide the battery door and Pager Clip off. 5. Carefully slip a screwdriver tip under the plastic wrapper on the battery pack and lift the battery out. 6. Unplug the battery connector. 7. Dispose of the Nickel Metal Hydride battery pack at any retail department or home improvement stores that recycles batteries. 8. Plug the new battery into the Pager’s connector. 9. Push excess battery wire into the space next to the connector. 10. Press the battery into the Pager compartment. 11. Replace the battery door, clip and screw (do not over tighten). 12. Insert the Pager into the Charger and fully charge the battery. Insert Dimensions 4-1/2” (114.3mm) 1-7/8” (47.6mm) Replacing the Battery Inserts JTECH JTECH JTECH Tighten
12 6413 Congress Avenue Suite 150 Boca Raton, Florida 33487 800-321-6221 Part Number 321045B5 © 2012, JTECH Communications, Inc. All Rights Reserved. SYSTEM WARRANTY JTECH Communications, Inc. warrants its equipment to be free from defects in materials and workmanship for a period of one year. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. Products must be returned with transportation charges prepaid. All warranty returns must also include a JTECH-issuesd RMA number, clearly displayed on the interior and exterior of the package(s). This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way. This warranty applies only to the original purchaser. The following are not covered under our one-year warranty: adapters, antennas, user-replaceable batteries, pager belt clips, pager promobacks, pager battery doors, or pager neck chains. Warranty also excludes liquid damage to master transmitter/controller (including base station, modules and any desktop or rack mount appliances), pagers, chargers or tablet hardware, lightning strikes or other acts of God that could affect the performance of the master transmitter/controller, pagers and peripherals.

Navigation menu