Bosch Automotive Service Solutions 576253 WiFi/BT Module Card User Manual
Bosch Automotive Service Solutions Inc WiFi/BT Module Card
Contents
User manual
USER’S MANUAL - Module PN 576253 Description The product is a WiFi and BlueTooth Module that requires an external antenna through a U.FL connector. Features include: • • • • • Murata WiFi/BT combo module LBEH5HMZPC on the board with the Broadcom BCM4339 utilized inside the Murata part. Compliant with IEEE802.11a/b/g/n/ac. Compliant with BlueTooth specification v4.1. WLAN supported through standard SDIO v3.0 host interface. BT is supported through Host Controller Interface (HCI). Mechanical Dimension Module has dimensions of a PCIE mini card, with 1mm nominal thickness. See below for dimensions. Bosch Automotive Service Solutions Inc Pinout Table Please note: For more information on interface signals and timing, see the Murata specification sheet LBEH5HMZPC. Pin Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Signal Name DI_PCM_SYNC N/C DI_PCM_RX GND DI_PCM_CLK N/C DO_PCM_TX DI_UART_4MBPS_CTS GND DO_UART_4MBPS_RTS N/C DI_UART_4MBPS_RX N/C DO_UART_4MBPS_TX GND VBAT VIO GND N/C VBAT GND N/C N/C N/C N/C GND GND N/C GND DI_WL_REG_ON I/O I/O -IN -I/O -I/O IN -OUT -IN -OUT -IN IN --IN ---------IN 31 32 N/C DI_BT_REG_ON -IN 33 34 35 36 N/C GND GND N/C ----- Description BT PCM SYNC, can be master or slave -BT PCM data input -BT PCM Clock, can be master or slave -BT PCM data output BT UART clear to send signal. Active-low. -BT UART request to send signal. Active-low. -BT UART serial data input. -BT UART serial data output. -POWER VBAT (5.0V) I/O POWER SUPPLY (1.8V) --POWER VBAT (5.0V) ---------WLAN regulator on signal. Used to power up or power down the internal WLAN regulators. When deasserted, the WLAN section is held in reset. -BT regulator on signal. Used to power up or power down the internal BT regulators. When deasserted, the BT section is held in reset. ----- Bosch Automotive Service Solutions Inc 37 38 39 40 41 42 DIO_SD_CMD N/C DI_SD_CLK GND DIO_SD_DATA0 DO_WL_HOST_WAKE I/O -IN -I/O I/O 43 44 45 46 47 48 49 50 51 52 DIO_SD_DATA1 DO_BT_HOST_WAKE DIO_SD_DATA2 DI_BT_DEV_WAKE DIO_SD_DATA3 N/C N/C GND N/C N/C I/O I/O I/O I/O I/O ------ WLAN SDIO Command Line -WLAN SDIO Clock Input -WLAN SDIO Data Line 0 WLAN host wake up output indicates that a host wakeup should be performed. Can also be programmed to be a WLAN GPIO. WLAN SDIO Data Line 0 HOST_WAKE of general purpose I/O signal. WLAN SDIO Data Line 0 DEV_WAKE of general purpose I/O signal. WLAN SDIO Data Line 0 ------ Bosch Automotive Service Solutions Inc Specifications • • • • Standards o 802.11a/b/g/n/ac o Bluetooth 4.1LE/2.1+EDR (Class 1) Chipset o Murata LBEH5HMZPC (Utilizing Broadcom BCM4339) Host Interface o WLAN: SDIO v3.0 o BT: Host Controller Interface (HCI) Radio o Antenna Dual Band 2.4GHz/5.0GHz Single U.FL connector o Operating Frequency WiFi b/g/n Band 2.400GHz – 2.4835GHz WiFi a/n/ac Band 5.180GHz – 5.825GHz Bluetooth: 2402MHz – 2480MHz o Modulation WiFi 802.11a OFDM WiFi 802.11b DSSS/CCK WiFi 802.11g OFDM WiFi 802.11n OFDM WiFi 802.11ac OFDM Bluetooth Header: GFSK Bluetooth Payload: 4-DQPSK Bluetooth Payload: 8-DPSK o Output Power WiFi 802.11a 14 +/- 2 dBm WiFi 802.11b 19 +/- 2 dBm WiFi 802.11g 16 +/- 2 dBm WiFi 802.11n 15 +/- 2 dBm WiFi 802.11ac 12 +/- 2 dBm Bluetooth 2.1: 11 +/-4 dBm Bluetooth LE: 10 dBm o Receive Sensiivity WiFi 802.11a -65 dBm WiFi 802.11b -76 dBm WiFi 802.11g -65 dBm WiFi 802.11n -64 dBm WiFi 802.11ac -54 dBm Bosch Automotive Service Solutions Inc • • • Bluetooth 2.1: -80 dBm Bluetooth LE: -70 dBm Power Consumption o Continuous TX 350mA o Continuous RX 160mA Operating Voltage o VBAT: 5.0VDC +/- 5% o VIO: 1.8VDC +/- 5% Environmental o Storage: -20C to 70C o Operating: 0C to 60C NOTE: For more detailed specifications, Consult the Murata part specification for p/n LBEH5HMZPC. Bosch Automotive Service Solutions Inc Regulatory Statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme à Industrie Canada exempts de licence standard RSS (s ) . Le fonctionnement est soumis aux deux conditions suivantes : ( 1 ) ce dispositif ne peut pas provoquer d'interférences et ( 2) cet appareil doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. IMPORTANT! Changes or modifications not expressly approved by Bosch Automotive Service Solutions Inc could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAN ICES-3 (A)/NMB-3(A) This equipment complies with radiation exposure limits set forth for uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux rayonnements définies pour un environnement non contrôlé. L'antenne (s ) utilisée pour ce transmetteur doit être installé pour fournir une distance de séparation d'au moins 20 cm de toute personne et ne doit pas être colocalisé ou fonctionner conjointement avec une autre antenne ou émetteur. Bosch Automotive Service Solutions Inc
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Vande Zande, Eric Create Date : 2016:08:01 15:25:16-07:00 Modify Date : 2016:08:01 15:25:19-07:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2016:08:01 15:25:19-07:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Document ID : uuid:f42dc621-fd01-4e83-b4c0-81d3b3e0d635 Instance ID : uuid:7c62e0ef-ba42-456f-a07e-e7e34ba4b075 Subject : 13 Format : application/pdf Title : Creator : Vande Zande, Eric Producer : Adobe PDF Library 10.0 Source Modified : D:20160801222509 Company : SPX Corporation Page Layout : OneColumn Page Count : 6EXIF Metadata provided by EXIF.tools