Bosch Power Tools Ds240 Users Manual

DS241 to the manual 822f12e8-7b62-4873-9324-17908d6fadd9

2015-02-02

: Bosch-Power-Tools Bosch-Power-Tools-Ds240-Users-Manual-484373 bosch-power-tools-ds240-users-manual-484373 bosch-power-tools pdf

Open the PDF directly: View PDF .
Page Count: 12

Installation Instructions

DS240 and DS241

Long Range Beam Smoke Detectors

1.0 Description

The DS240 and DS241 are long range projected beam type smoke

detectors which consist of a separate transmitter and receiver. Internal

pointability provides coverage flexibility without the need for brackets.

Automatic Signal Synchronization and Range Adjustment reduce

installation costs. Selectable sensitivity and alarm response time

provide installation flexibility.

2.0 Specifications

•Operating Voltage: DS240: 18.0 VDC to 32.0 VDC

DS241: 10.2 VDC to 15.0 VDC

• Standby Current: DS240: Receiver: 45 mA @ 24.0 VDC

Transmitter: 20 mA @ 24.0 VDC

DS241: Receiver: 50 mA @ 12.0 VDC

Transmitter: 20 mA @ 12.0 VDC

•Receiver Alarm

Current: DS240: 60 mA @ 24.0 VDC

DS241: 75 mA @ 12.0 VDC

•Range (distance

between transmitter

and receiver):30 ft to 350 ft (9 m to 107 m)

•Spacing (distance

between systems): Allow no more than 60 ft (18 m) between

systems. Sixty foot spacing is confirmed

by Underwriters Laboratories, Inc. testing.

•Pointability: Internally pointable optics for ±90°

horizontal, and ±10° vertical adjustment.

• Sensitivity: Field selectable for 20, 30, 40, 50, 60, or

70 percent beam obscuration.

• Alarm Contacts: Normally Open contacts rated 1 A,

60 VDC maximum for DC resistive loads.

Do not use with capacitive or inductive

loads.

• Trouble Contacts: Normally Closed contacts rated 1 A, 60 VDC

maximum for DC resistive loads. Do not

use with capacitive or inductive loads.

•Aux. Alarm

Contacts: Form "C" (NO, C, NC) contacts rated 1 A,

60 VDC maximum for DC resistive loads.

Do not use with capacitive or inductive

loads.

• Tamper: Receiver: Access door tamper switch in

series with trouble contacts.

Transmitter: Upon cover’s removal, cover

tamper switch interrupts

transmission.

• System Signaling: Conventional 4-wire system. Not for use

with systems that incorporate an alarm

verification feature.

• Signal Delay: Fire: Selectable 30 sec or 5 sec

Trouble: 20 ± 2 sec

•Temperature: The storage and operating temperature

range is -22°F to +130°F (-30°C to +54°C).

For UL Listed installations, the range is

+32°F to +130°F (0°C to +54°C).

•Mounting: The units are designed to be mounted to

4 in. (10 cm) square or octagonal

electrical boxes (not supplied).

•Listings and

Approvals: UL S3019

ULC CS692

MSFM Permit #1943

NY City MEA Acceptance #MEA274-93-E

CSFM #7260-1062:106

FM Job #OX2A9.AY



•Standard

Accessories: DIS2000 Remote Test/Indicator Plate and

Test Cable

•Options: DIS240 Remote Indicator Plate, TK240

Field Test Kit, AL240 Alignment Light, and

TC2000 Test Cord.

3.0 Principle of Operation

Each DS240 or DS241 beam smoke detector has a separate

transmitter and receiver. The transmitter transmits an invisible infrared

beam of a specific frequency and intensity. The receiver detects, then

measures the beam’s intensity (see

Figure 1

Figure 1 - Infrared Transmission

As the beam is obscured by smoke, the receiver senses a decrease

in the signal strength and measures that decrease. The receiver

compares the signal level with two preset thresholds: an alarm

threshold which is set using the sensitivity switch and a trouble

threshold which is preset at approximately 10%. If the signal falls

below the alarm threshold for the programmed alarm period, the

receiver signals an alarm (see

Figure 2

Figure 2 - Beam Obscuration

If the signal falls below the trouble threshold for more than 20 sec,

such as might happen if the beam is blocked by a foreign object, the

receiver signals a trouble condition (see

Figure 3

Figure 3 - Beam Blockage

The receiver automatically compensates for the gradual loss of signal

due to dust/dirt build-up on the cover. After 50 percent of the signal is

lost, the receiver will indicate a trouble. When the dust/dirt build-up is

cleaned or the blockage is removed, the detector automatically goes

back to its normal operation level.

A trouble will be indicated at the receiver if the beam strength is

increased by more than 20% for greater than 20 sec. Causes include

improper initial alignment or the removal of a partial beam blockage

at the time of alignment. Preform a fine-tune alignment (see

Section

7.3 Fine Tune Alignment

on page 6).

Downloaded from: http://www.guardianalarms.net

4.0 Installation Considerations

The proper location and spacing of detectors is critical in a properly

installed and operating fire alarm system. For best results, it is

recommended that the detectors be located and spaced in

accordance with the National Fire Protection Association (NFPA)

Standard 72 "The National Fire Code.” This standard is available at a

nominal cost from The National Fire Protection Association,

Batterymarch Park, Quincy, MA, 02269.

In all installations, good engineering judgement should prevail. The

following are some general considerations:

• Do not use mirrors. The detectors should be installed with a

clear line-of-sight between the transmitter and receiver.

• The beam path should be clear of moving objects.

• Set the sensitivity based on the distance between the transmitter

and receiver. See

Section 7.2 Sensitivity Adjustment

on page 5.

• The detectors may be mounted directly to the ceiling or to side

walls. Do not mount the units where the beam path may run

parallel within 4 in. (10.2 cm) of a corner.

• For a sloped or peaked ceiling, the beam path should be located

within 3 ft (1 m) of the ceiling’s peak.

• Stratification of air may hinder smoke from reaching detectors

mounted close to the ceiling. Stratification occurs when smoke,

rising because it is warmer than the surrounding air, reaches a

level where it is the same temperature as the surrounding air

and will not rise to the ceiling. If stratification is considered a

possibility, extra beams should be installed where stratification

is expected.

• Avoid areas subject to normal smoke concentrations such as

kitchens and garages.

• Do not install units where normal ambient temperatures are

below -22°F (-30°C) or above +130°F (+54°C).

The following are some specific installation considerations:

4.1 Avoid Sources of Heat and Air Movement

The detectors should be located where the beam path will not pass

near heating and cooling outlets.

• Don’t mount where hot or cold air can blow directly into the beam

path.

• Heating, ventilating, and air conditioning systems can cause

smoke to be blown away from the beam path.

- Smoke must accumulate in the beam path to be detected.

• Heaters mounted close to the beam path can cause the beam to

become distorted.

You can test for beam distortion by monitoring the signal voltage.

After setup, the signal voltage of the detector should read 4 VDC.

Monitor the voltage and turn on all heating and cooling devices in the

area. The signal voltage should not fluctuate more than 0.20 VDC. If

it does, the detector should be moved to avoid these disturbances.

4.2 Avoid sources of bright light

Sunlight and light from extremely bright sources such as the exposed

bulbs of high pressure sodium, mercury vapor, and metal halide

lights can cause stray signals. The receiver should not be pointed

toward any of these sources.

Sunlight: Avoid pointing the receiver directly at the rising or setting

sun. If you are installing the unit where sunlight can’t be avoided,

mount the receiver slightly higher than the transmitter and aimed

down toward the transmitter. This should reduce this problem by

causing the receiver to look below the horizon.

Bright Lights: Don’t mount the receiver where it is looking at exposed

bulbs of high pressure sodium, mercury vapor, and metal halide

lights. The illustration below shows where these exposed lights

should be avoided.

225 ft. (68.6 m)

350 ft. (106.8 m)

4.5 ft. (1.4 m)

Keep bright lights out of this area

14.5 ft.

(4.4 m)

Receiver

Bare fluorescent lights may also pose a problem especially in long

hallways where a series of lights run perpendicular to the beam.

Incandescent lights are not a problem as long as they are not directly

in the beam path.

4.3 Use the correct wire gauge and length

Beam smoke detectors are often used to protect very large areas.

This means that the wire runs used to power the detectors and signal

alarm conditions can be very long. The voltage available at the end of

very long wire runs may not be sufficient to power the detector,

especially when the system is running on battery backup. It is very

important that the correct wire gauge is used for these installations.

Use the following chart to determine the proper wire size, wire length

and the number of transmitter and receiver pairs that can be used.

eriW htgneL

eziSeriW

GWA41 )mm8.1( GWA61 )mm5.1( GWA81 )mm2.1(

)m251(tf005 )m403(tf0001 )m267(tf0052 )m4251(tf0005

sriap02 sriap01 sriap4 sriap2

sriap31 sriap6 sriap3 riap1

sriap8 sriap4 sriap2 riap1

4.4 Provide a stable mounting surface

Beam smoke detectors depend on the measurement of the projected

beam to sense smoke. Therefore, shifts in the alignment of the beam

due to movement of the transmitter/receiver can cause trouble or

alarm conditions.

• Always select a stable mounting surface.

• Never mount the unit to a suspended support such as a pipe or

length of wood supported at only one end.

This type of mounting can create a “pendulum effect” which greatly

multiplies even very small movements at one end of the support. For

example, a 2 in. (5.1 cm) movement translates into a beam

misalignment of over 20 ft at 350 ft (6 m at 107 m).

Mounting surfaces should be supported at opposite corners to reduce

the pendulum effect.

• Always select surfaces not subject to building movement.

The automatic compensation circuits of the DS240 and DS241 will

eliminate most problems created by normal building expansions

and contractions. In some unusual circumstances, the walls and

support structure may be subject to more significant movement due

to the operation of heavy equipment, such as cranes, anchored to the

top of the walls.

When in doubt about mounting surface stability, measure the signal

voltage of the detector. This voltage should be 4.0 VDC. Misalignment

of the beam can cause this voltage to increase or decrease. The

detector will indicate a trouble condition when the voltage increases

to more than 4.8 VDC, or when it decreases to less than 2.0 VDC over

a long period of time or to 0.4 VDC greater than 20 sec. For more

information on reading this voltage, see

Section 8.3 Reference

Voltage Calibration

on page 6).

If movement of the mounting surface is suspected, relocate the

detector to a surface that does not move or add supports to the

mounting surface to prohibit movement.

•DO NOT over-tighten the mounting screws.

When the detector is mounted to an electrical mounting box

[4 in. (10 cm) square or octagonal], the mounting plate may bow as a

result of the mounting box screw tabs being below flush with the top

edges of the mounting box. Over-tightening the mounting screws

bows the mounting plate inward at the bottom, causing the optics to

aim low.

Irregularities in the flatness of the mounting box edge surfaces or

screw tabs will worsen this condition. Using only mounting boxes

with flat, regular surfaces and properly formed screw tabs, and

tightening the mounting screws to secure the mounting plate to

2 in./lb torque will minimize any misalignment caused by bowing of

the mounting plate.

4.5 Consider the effects of stratification in cold environments

In very cold environments such as unheated warehouses, smoke

may cool very quickly and is less likely to rise to the ceiling. Consider

additional units at lower mounting heights to help compensate for

this situation.

4.6 Consider the expected Fire load

When designing a fire alarm system, consider the expected fire load

within the application.

For instance, fires caused by the ignition of flammable petroleum-

based liquids usually result in a rapid buildup of heavy smoke. When

these types of fires are probable, use sensitivity settings 0 or 1 which

provide a response time of 5 sec.

5.0 Mounting

NOTE: This product is not designed for use in outdoor applications.

Install a 4 in. (10 cm) square or octagonal electrical box (not supplied)

to a rigid surface that will not be subject to movement or vibrations.

NOTE: If not mounting to an electrical box, be sure the surface will

not be subject to movement or vibrations. For example: do

not mount directly to a suspended ceiling without extra

support.

• Remove the receiver's access door (1 screw), then remove the

cover (4 screws). See

Figure 4

Figure 4 - Access Door and Cover

• Remove the receiver’s backplate by removing the single

mounting screw from the top of the circuit board carrier plate then

separating the two plates (see

Figure 5

WIRING

ENTRANCE

MOUNTING

SLOTS (4)

DO NOT

REMOVE

REMOVE TO

EXPOSE BACKPLATE

Figure 5 - Removing the Backplate

• Bring wiring from the electrical box through the wire entrance.

NOTE: All wiring should be unpowered.

• Securely mount the backplate to the electrical box.

• Return the circuit carrier plate to the backplate. Secure it in place

with the single mounting screw.

• Repeat this mounting procedure for the transmitter.

ACCESS DOOR

COVER MOUNTING

SCREWS (4)

6.0 WIRING

Only apply power after all connections have been made

and inspected.

• Wire the transmitter and receiver terminals as follows (see

Figure 6

NOTE: Do not install on verified fire circuits.

Figure 6 - Wiring a Single Unit

NOTE: Do not coil excess wiring inside the units.

•Transmitter Terminals 1 & 2:

Input power terminals. See

Section 2.0 Specifications

on page 1

for the operating voltages of the DS240 and DS241.

•Receiver Terminals 1, 2 & 3:

Form "C" Auxiliary relay contacts. Terminals 1 & 2 will open on fire

alarm; Terminals 2 & 3 will close (short) on fire alarm.

•Receiver Terminals 4 & 5:

Normally Open Fire alarm contacts will close (short) on fire

alarm.

•Receiver Terminals 6 & 7:

Normally Closed Trouble contacts will open for trouble alarm.

•Receiver Terminals 8 & 9:

Input power terminals. See

Section 2.0 Specifications

on page 1

for the operating voltages of the DS240 and DS241.

NOTE: Resetting from a fire alarm requires power to the receiver to

be interrupted for at least one second. If not provided by the

fire panel, it can be accomplished by installing a switch in

series with Terminal 9.

Remote Indicator Plate

The DIS2000 Remote Indicator Plate is shipped with the DS240/

DS241 as a standard accessory. Although the Remote Indicator Plate

is not required, the manufacturer recommends its installation to

provide a means of checking the condition of the detector from ground

level.

If a DIS2000 or DIS240 Remote Indicator Plate will be used, install

the Remote Indicator Connector to the receiver now (see Figure 7).

NOTE: The DIS240 remote indicator should be located no further

than 100 ft (31 m) from the receiver and wired with 18 AWG

(1.2 mm) or larger wire. The DIS2000 may be wired up to

500 ft (152 m) from the receiver.

• Slide the Remote Indicator Connector over the pins just to the

right of the receiver’s terminal strip.

Figure 7 - Connecting the DIS2000 Remote Indicator Plate

NOTE: If connecting a DIS240 Remote Test/Indicator Plate,

consult the

DIS240 Installation Instructions

(P/N: 24171).

7.0 SET-UP

Before starting this section, confirm that all connections have been

made and are secure, then apply power to both units.

• Press the Aim Mode button (directly above the green LED) on the

transmitter (see

Figure 8

). This allows the transmitter to power

up while its cover is off.

AIM MODE

BUTTON

GREEN

LED

Figure 8 - Cutout View of Transmitter Circuit Board Showing

Aim Mode Button Location

- Check the transmitter’s green LED. It should be flashing on

and off.

CAUTION

Alarm Loop

Power Loop +

Power Loop –

Fire Alarm

Control Panel

DS240/DS241 Receiver

7654

Fire

Alarm Trouble

Alarm

–+

10 to 32

VDC

EOL

Voltage Monitor

Ground (–)

Red LED

Green LED

Yellow LED

DIS2000

Violet

Black

Red

Yellow

Green

Remote Indicator

Plate Connector

1234567

AUX.

RELAY

ALARM FIRE

ALARM TRBL

ALARM

–+

VDC

Receiver

–+

Transmitter

End of Line

resistor

Alarm Loop

Power Loop –

Power Loop +

Fire Alarm

Control Panel

- If the LED is off, check for the presence of power and proper

polarity on Terminals 1 (–) & 2 (+).

- A steady green LED indicates a faulty transmitter, and the unit

should be returned to the factory.

• Check the three receiver LEDs (see

Figure 9

Red/Alarm

Trouble/Yellow

Green/Normal

Figure 9 - Receiver's LEDs

- It is normal for all of them to be on at this time, with the green

indicator either flashing or constantly on.

- If all are off, check for the presence of power and proper

polarity on Terminals 8 (–) & 9 (+).

• Mount an AL240 strobe aiming light or equivalent (such as a

Faraday 5508) as close to the receiver as possible (preferably on

top of the receiver).

- Point it at the transmitter as your guide for aiming (an aiming

light may not be necessary for short distance separations).

7.1 Preliminary Alignment

Each optical module is equipped with two alignment mirrors (one on

each side) for initial alignment (see

Figure 10

To initially align an optical module, look into either mirror from a side

angle at least 2 ft (61 cm) from the module. The optical module is

pointed at objects seen in the mirror when the orange colored front

bore sight is in the center of the rear bore sights (see

Figure 11

Rear Bore Sights

Front Bore Sight

Figure 11 - View of the Alignment Mirror

with Bore Sights Aligned Properly.

HINT: Use alignment sights like aiming a gun.

• Rotate the transmitter's optical module left or right until the

image of the aiming light (or receiver image, if aiming light is not

used) can be seen in the mirror.

- If initially aimed too high or low, adjust the Vertical Fine Tuning

adjustment allen screw (with supplied allen wrench) slightly

up or down until the image is found.

• Use the Vertical Fine Tuning adjustment screw and the

Horizontal Fine Tuning adjustment screw to fine tune the image

to the center of the mirror (in-line with the front and rear bore

sights).

• Replace and secure the transmitter's cover when this alignment

procedure is complete.

• Check the transmitter's green LED. It should be flashing.

• Replace and secure the transmitter's access door.

• Align the receiver to the image of the transmitter using the above

preliminary alignment procedure.

• Check the receiver's green LED. It should be flashing. This

indicates that the preliminary alignment is complete.

- If the receiver’s green LED is not flashing, repeat the prelimi-

nary alignment procedure for the receiver.

7.2 Sensitivity Adjustment

Use the chart below (

Figure 12

) to aid in the sensitivity adjustment.

Figure 12 - Recommended Settings Chart

NOTE: Positions 8 and 9 are not valid positions. They are not to be

used.

• Select the appropriate sensitivity setting from the above chart

based on the distance between the transmitter and receiver.

• Set the receiver’s Sensitivity switch at this setting.

• The Sensitivity switch is located just to the right of the optical

module on the receiver. The indicator or pointer marking runs

along the side of the switches' shaft (see

Figure 13

Figure 13 - Sensitivity Switch

• The recommended settings chart lists distances with some

settings that overlap. For more sensitive detection, select the

lower number setting. For better immunity to false alarms, select

the higher number setting.

FRONT VIEW

HORIZONTAL

FINE TUNE

VERTICAL

FINE TUNE

ALIGNMENT

MIRRORS

SIDE VIEW

ALIGNMENT

MIRROR

REAR BORE SIGHTS

FRONT BORE SIGHT

Figure 10 - The Optical Module

sgnitteSdednemmoceR

hctiwS gnitteS ytivitisneS mralA esnopseR htgneLmaeB

0%03ces5)m13-9(tf001-03

1%06ces5)m701-13.tf053-001

2%02ces03)m51-9(tf05-03

3%03ces03)m32-41.tf57-54

4%04ces03)m13-12(tf001-07

5%05ces03)m34-72.tf041-09

6%06ces03)m55-73(tf081-021

7%07ces03)m701-94(tf053-061

7.3 Fine Tune Alignment

• Connect the supplied TC2000 Test Cable to Pins 1, 2 and 3 of

P6, the group of pins located just to the right of the receiver’s

terminal strip (see

Figure 14

Figure 14 - TC2000 Connection

- Temporarily disconnect the Remote Indicator Plate connector, if

installed.

• Connect a 20,000 Ohm/volt (or greater) DC VOM to the black

(–) and red (+) leads of the TC2000.

- Set meter scale so that readings of 0.0 to 5.0 VDC can be

read.

• Check the three LEDs on the receiver.

- If the beam is being received by the receiver, the green LED

should be flashing, and the red and yellow LEDs should be on

steady.

- If the green LED is on steady, the beam is not reaching the

receiver. If this is the case, the preliminary alignment proce-

dure should be attempted again.

• Observe the meter readings and adjust the receiver’s optical

module using the Horizontal and Vertical Fine Tuning adjustment

screws for a maximum reading on the meter. This is the most

critical process of alignment. For the most effective operation

of this system, the peak voltage during fine tune alignment

must be obtained.

NOTE: When performing fine tune alignment, keep arms and hands

away from the front of the receiver and out of the beam path.

• The maximum voltage peaked reading will vary depending on the

distance between the transmitter and receiver. The acceptable

peaked voltage range is 0.50 to 5.00 V. The voltage at the

receiver is greater at shorter distances. It is very important to

peak the voltage to insure a stable trouble free detector.

Hint: Make a note of the alignment voltage. It may be helpful if

future troubleshooting is necessary.

• After completing the fine tune alignment, remove the test cable,

then replace and secure the receiver's cover.

• Check the status of the receiver’s green LED. It should still be

flashing.

• With the meter still connected to the test cable, re-install the test

cable to P6 through the opening in the cover (red lead towards

center of unit).

• An alarm test may be performed here if desired by connecting

the white and black wires of the TC2000. To reset the unit,

temporarily remove power.

• Press the receiver’s Set-up button located just below the P6/test

cable connection (see

Figure 15

). Press only if the covers are

on both transmitter and receiver.

- This starts a one to two minute automatic internal setup

process that results in a reference voltage for measuring

beam blockages.

Setup

Button

LEDs

Figure 15 - The Receiver's Set-up Button

- The red and yellow LEDs should turn off, and the green LED

will turn on steady. After some voltage fluctuations, the meter

should settle at 5.0 VDC.

NOTE: Be careful not to block the beam or move the units during

this time.

- At the end of the setup period, the receiver’s green LED will

flash, and the voltage will drop to between 3.8 and 4.2 VDC.

This is a reference voltage that later readings can be com-

pared to when determining the need for cleaning.

• If the voltage is not between 3.8 VDC and 4.2 VDC, push the Set-

up button again.

• After set-up is complete, remove the test cable (and reconnect

the Remote Indicator Plate connector if used).

• Replace and secure the access door.

8.0 Other Information

8.1 Fire Alarm Reset

To reset the receiver after a fire alarm has occurred, remove power

from the receiver for at least one second, then re-apply (see also,

Section 8.4 Power Outage

on page 7).

8.2 Cleaning

At least once a year, the outside of the covers should be cleaned with

a common window cleaner and a soft, clean cloth. Under normal

conditions, this should not result in a trouble alarm as long as the

beam is not continuously blocked for more than 18 sec. After cleaning,

recheck the reference voltage. If the voltage is less than 3.8 VDC, or

greater than 4.2 VDC, calibrate the units (see

Section 8.3 Reference

Voltage Calibration

8.3 Reference Voltage Calibration

The reference voltage of the detectors should be checked at least

once a year (or more often if required by local regulations or authorities

having jurisdiction). Clean covers are necessary for proper

reference voltage readings.

To check the reference voltage, remove the receiver's access door

and measure the reference voltage, using the supplied test cable, or

measure the voltage at the DIS240 Remote Indicator Plate (if used).

If the voltage is less than 3.8 VDC, remove the cover and perform a

fine tune alignment including use of the Set-up switch. If above 4.2

VDC, press the Set-up button. Calibration is not necessary if the

voltage is between 3.8 VDC and 4.2 VDC.

8.4 Power Outage

When power is removed, then reapplied to the receiver (such as in a

power outage or alarm reset), the original reference voltage

information is lost.

If the cover is on at the time of power-up, the receiver will automatically

restart the internal set-up process (to get a new reference voltage)

when power is applied. If the cover is off, the Set-up button will have to

be pressed after the cover is reattached.

8.5 Remote Indicator Plate Connector

Momentarily connecting the orange and black leads of the connector

(see

Figure 16

) will produce a test alarm. For a remote test, install a

momentary switch between the orange and black wires.

ORANGE - Remote Alarm Test

BLUE - Analog ref. voltage out

BLACK - Common (-)

RED - Red LED indicator

YELLOW - Yellow LED indicator

GREEN - Green LED indicator

Figure 16 - Remote Indicator Plate Connector

The black and blue wires may be connected to an analog meter for

reference voltage measurements. The red, yellow, and green wires

may be connected to remote LEDs.

Each wire is current limited to a maximum of 10.0 mA DC.

8.6 Smoke Density/Obscuration Information

The total obscuration of the infrared beam is dependent upon the

density and width of the smoke cloud along the beam path. As the

width of the smoke cloud increases along the beam path, less dense

smoke will be needed for an equal obscuration of the beam path. In

practice, the smoke cloud is assumed to be the entire distance of the

beam path; therefore, the total obscuration required for alarm should

be selected by setting the Sensitivity Pot Setting as recommended in

Section 7.2 Sensitivity Adjustment

on page 5.

Since the total obscuration of the beam by smoke increases with

distance between the units (because more smoke will be within the

beam path), the detector can be made less sensitive as the distance

increases. Additionally, the sensitivity of the detector should be made

less at greater distances because obscuration by other contaminants

such as dust increases. The sensitivity should be set to respond to

the proper smoke obscuration and also to reduce the chance of a

false activation.

As shown in

Figure 17

, if the expected smoke density is 0.5 percent

per ft (per 30 cm), the obscuration at 50 ft (15 m) is 20 percent and at

250 ft (95 m) it is 73 percent.

Figure 17 - Smoke Density/Obscuration Chart

The next chart (

Figure 18

) shows the Sensitivity Pot Setting (total

obscuration) that is needed for alarm.

Figure 18 - Sensitivity Pot/Obscuration Chart

8.7 Field Sensitivity Measurements

The detectors automatically compensate for the effects of dust or dirt

accumulation on the covers and for component aging. The NFPA

requires that the detector's sensitivity be measured in the field, and

requires that these measurements be made within one year after

initial installation and every alternate year thereafter (reference NFPA

72). A TK240 Test Kit should be ordered to test the unit’s sensitivity in

the field. The chart (

Figure 19

) below represents alarm information

for the filters in the TK240 as well as the Sensitivity Test Kit provided

with the units.

Figure 19 - Sensitivity/Response Chart

ytivitisneS toP gnitteS

latoT noitarucsbO mralAta

23ro0 4

56ro1 7

%02 %03 %04 %05 %06 %07

ytivitisneS gnitteS TONtsuM mralA TSUM mralA

23ro0 4

56ro1 7

)retlifon(%0 )retlifon(%0 retlif%02 retlif%02 retlif%04 retlif%04

retlif%04 retlif%06 retlif%06 retlif%08 retlif%08 retlif%08

330 (100m)280 (85m)230 (70m)

180 (56m)

130 (40m)80 (24m)

30 (9m)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

UL Minimum Sensitivity

UL Maximum Sensitivity

20%

30% 40% 50%

Distance Between Transmitter and Receiver

70%60%

The Sensitivity Test Kit (supplied) may be used to check the sensitivity

of the detectors during installation only. For field testing, the TK240

must be used. Each filter decreases the detector’s signal by a defined

amount. When each filter is placed in front of the receiver’s optical

module for at least 30 sec (5 sec for position 0 or 1), the approximate

sensitivity setting of the installed detector can be determined by the

detector's response as shown in

Figure 19

on page 7.

NOTE: Testing these detectors will activate a fire alarm. Be sure to

inform all concerned personnel before performing and testing.

8.8 FCC Compliance Notice

This equipment has been tested and found to comply with the limits

for a class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in strict accordance with the manufacturer's

instructions and recommendations, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment on and off, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

the receiver.

• Consult the installing company or an experienced radio/TV

technician for help.

The booklet, "How to Identify and Resolve Radio-TV Interference

Problems,” prepared by the Federal Communications Commission

(FCC) may prove helpful. This booklet is available from the U. S.

Government Printing Office, Washington, DC 20402. Please specify

Stock No.004-000-00345-4.

9.0 Troubleshooting

10.0 Installing Multiple Units

11.0 Quick Start Installation Flow Chart

130 Perinton Parkway, Fairport, NY 14450-9199 USA Installation Instructions DS240/DS241 Long Range Beam Smoke Detectors

Customer Service: (800) 289-0096; Technical Support (888) 886-6189 Page 12 of 12

Bosch Power Tools Ds240 Users Manual

DS241 to the manual 822f12e8-7b62-4873-9324-17908d6fadd9

Navigation menu

Versions of this User Manual:

Views

Navigation