Bosch Security Systems 0407-1 Door/Window Security Transmitter User Manual 51549
Bosch Security Systems Inc Door/Window Security Transmitter 51549
8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 51549 |
| Application ID | Hyb3eHjUf+3wxjf79QTJEg== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 8.98kB (112252 bits) |
| Date Submitted | 1999-08-03 00:00:00 |
| Date Available | 1998-06-15 00:00:00 |
| Creation Date | 2001-05-24 17:59:54 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-05-24 17:59:56 |
| Document Title | 51549.pdf |
| Document Author: | VicodinES /CB /TNN |
EXHIBIT 5 Installation and Operating Instructions Pam. 2.1033(b)(3) Retlif Testing Laboratories Test Report No. R-7457—1 FCC ID: EVS-0407-1 Installation Instructions for the RF3401 Wireless (RF) PointTransmitter 1.0 GENERAL INFORMATION The RF3401 PointTransmitter is a UL Listed, magnetic and dry con- tact wireless transmitter used lor monitoring doors. windows or other dry contact devices. The unit is equipped With an internal reed contact for use With an external magnet assembly, a cover tamper swuch and RF superin- sion. The RF3401 also has the capability to accept a supervised dry contact input lrorn an external device. Supervision is provided by transmitting a low power level signal to the receiver every 70 minutes it there is no other activity. All transmis~ sions from the RF3401 send battery status information to the panel. 2.0 SPECIFlCATIONS - Description: Dimensions: - Transmitter w/o Mounting Plate: 3,25wx 1.4h x,75d (76 5 x 35 x18 mm) 325wx l.4hx,125d (76.5 x 35 x 3 2 mm) -20" to +150°F (729 to +65°C) 0 to 95% relative humidity (non-condens- ing, +32“ to +120°F (0° to +49” C) for UL Certificated installations. Supplied by a SVDC lithium battery. A minimum of 5 years under normal operating conditions with the recom- mended battery types - Recommended Battery Types: Duracell DL123At Energizer EL123AP, or Panasonic CFll 23A. DS74OOXi Version 3+ Control/ Communicatorwnh software ver- sion 3.07 or above. RFSZOO Series Multiplex Bus reA ceivers and Repeaters. Magnet-RF-to Assembly' “Supplied in packages of 70 RF3401 Wireless Point Transmitter. - Mounting Plate: Operating Temperature: - Operating Voltage: - Battery Llfe: - Compatlbla Control Panels: ' Compatible Receivers: - Options: 3.0 MOUNTING THE POINT TRANSMITTER rm? The maximum range of the Point Transmitter. in open v], t L“? air, is approximately 1000 feet (300 m). In normal house- hold or commercial applications it is recommended that the Point Transmitter be kept Within 100 leet (30 m) oi IMPORTANT the RF3222 receivers Avoid mounting the PointTransmitter on metal surlaces as it may reduce the range ol the unit. Placing the Folni Transmitteron lerrous metal tiron orsteel) surlaces may attest the operation of the magnetic Contact Wm ‘l tMPORTANT It is recommended that the Point Transmitter be mounted on the door or Window frame and that the magnet as— sembly be mounted on the door or Window. El IMPORTANT Recommended Mounting ~ Position the Mounting Plate over the desired location and attach With the supplied screws, Release KT!!! O 5 77 Mounting Holes - Be sure to note the location at the magnet when mounting the base. - Slide the PointTransmitterover the baseto lock it into place as shown below: /.f~/ til ~ The Point Transmitter may be released trorn the base by pressing the Release Tab with a small screwdriver or a paper clip ' For UL Certificated installations, mount the lransmitterusrng the pm- vrdsd Tamper Screw j /Tamper Screw 4 , Mountlng without the Mounting Plate - If the battery was installed in the PointTransmitter, remove it at this time ' Using a small screwdriver, gently lift the printed circuit board away trom the case mounting clips. You do not need to remove the cover to remove the board. 0 Rock the board gently to loosen the battery clips trorn the case and to slide the board away from the mounting clips near the area where the cover connects to the base. Detection Systems, Inc., 130 Perinton Parkway, Fairport, New York, USA 14450-9199 © ® (716) 223-4060 - (900) 239-0095 - Fax: (71 5) 223-9130 4/98 Copyright © 1998 Detection Systems, lnc. RF3401 Installation Guide PIN 36259A - Mount the Paint Transmitter in the desired location taklng note that the magnet Will need to be on the same side of the case as the reed Switch, Magnet Side Mounting Holes Mounting the magnet - Mount the magnetas shown below. The magnetmust mount within 3/4" (19 mm) of the base or the unit. End View from the end “Ht opens I Remove the Reed Swrlcn it using externai conlaots \i/ \/ I \r’ 70K? 7 70K ‘ 70K; 4.0 |NSTALLTHE BATTERY - Install the recommended type Duracell DL123A, Energizer EL123AP or Panasonic CR123A battery. Be sure to observe the polarity 5.0 SETTING UP MAGNETIC OF! EXTERNAL CON- TACTS The RF3401 has the capacity to monitor magnetic or dry external coniactsfxternalNormallyclosed(NC)orExternaINormallyOpen (N0) contacts may be monitored. Il using the HF3222 Receiver. the RF3401 can not men? itor both magnetic and external contacts at the same time. Remove the reed swrtoh il external contacts are monitored. IMPORTANT The contact input is Supervised. using a 2.21kfl End-Ol-Line (EOL) resistorThe total wire length lor the external Wiring cannot exceed 50 feet (15 mi Do not place an EOL across the external contact termi- nals ii an external contact is not used. awn We“ Remove the Reed Swrtch il usmg external contacts EOL 2.21 KQ Typical Normally Open (N0) w ing 6.0 PROGRAMMING THE DS74ODXi Control/Com- municator There is a two part ID sticker located inside the cover of the HF3401. You WI" need the number off this sticker to program this device into the system. 1577701574— ID Number IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII| IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 15777m137 See your DS74OOXi Wireless Relerence Guide tor programming in- torrnation for wireless type devices. FCC COMPLIANCE NOTICE' The device complies with Part 15 ol the FCC Rules and with Res-210 dl Industry and Snience Canada. Operation is subject to the loliowing two conditions: (1) this device may not cause harmlui interlerence, and (2) this iMPORTANT device must accept any interlerence received, including interference that may cause undesirable operation Changes or modifications not expressly approved by Detection Systems. inc. can void the users authority to operate the equipment, Page 2 Copyright © 1995 Detection Systems, Inc. RF3401 Installation Instructions
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2001:05:24 17:59:54 Producer : Acrobat Distiller 4.0 for Windows Author : VicodinES /CB /TNN Title : 51549.pdf Modify Date : 2001:05:24 17:59:56-04:00 Page Count : 3EXIF Metadata provided by EXIF.tools