Bosch Security Systems DCNMWAP DICENTIS WIRELESS ACCESS POINT User Manual DICENTIS Wireless ConfigSWM

Bosch Security System BV DICENTIS WIRELESS ACCESS POINT DICENTIS Wireless ConfigSWM

Contents

07a_User Manual_DICENTIS_Wireless_ConfigSWM_V1 0_enUS

DICENTISWireless Conference System en Configuration manual
Table of contents1Safety 42About this manual 52.1 Intended audience 52.2 Copyright and disclaimer 52.3 Document history 53System overview 64First use configuration 74.1 Login 84.2 Wireless Device initialization 95Web interface application 105.1 Manage discussion 125.2 Prepare discussion 135.3 Voting 155.4 System settings 165.4.1 Users 175.4.2 Audio 175.4.3 Equalizer 185.4.4 Cameras 185.4.5 Licensing 195.4.6 Network and general settings 195.4.7 Seats 205.4.8 Date and time 215.4.9 Upgrade 215.5 Participants 235.6 Switch system on/off 245.7 Battery & Signal 245.8 Logging 255.9 System info 255.10 Logout 256Wireless Access Point LED behavior 267Troubleshooting 277.1 Customer service 27DICENTIS Table of Contents | en 3Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
SafetyPrior to installing or operating products, always read the Important Safety Instructions whichare available as a separate multilingual document: Important Safety Instructions (Safety_ML).These instructions are supplied together with all equipment that can be connected to themains supply.Old electrical and electronic appliancesElectrical or electronic devices that are no longer serviceable must be collected separately andsent for environmentally compatible recycling (in accordance with the European WasteElectrical and Electronic Equipment Directive).To dispose of old electrical or electronic devices, you should use the return and collectionsystems put in place in the country concerned.14en | Safety DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
About this manualThe purpose of this manual is to provide information required for configuring, preparing, andmanaging the DICENTIS Wireless Conference System. This manual describes in general how touse the Wireless Access Point (DCNM-WAP) web interface. If required, refer to the HardwareInstallation Manual and Wireless Devices User Manual of the DICENTIS Wireless ConferenceSystem. This manual is available as a digital document in the Adobe Portable Document Format (PDF).Refer to the product related information on: www.boschsecurity.com.Intended audienceThis manual is intended for people who have the authorizations to configure, prepare and/ormanage a DICENTIS Wireless Conference System.Copyright and disclaimerAll rights reserved. No part of this document may be reproduced or transmitted in any form byany means, electronic, mechanical, photocopying, recording, or otherwise, without the priorwritten permission of the publisher. For information on getting permission for reprints andexcerpts, contact Bosch Security Systems B.V..The content and illustrations are subject to change without prior notice.Document historyRelease date Documentation version Reason2015.03 V1.0 1st edition.22.12.22.3DICENTIS About this manual | en 5Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
System overviewThe DICENTIS Wireless Conference System is a “standalone” IP based system. It usesWiFi IEEE 802.11n for wireless distribution and processing of audio and data signals. For an overview of the system, please refer to the DICENTIS Wireless Conference Systeminstallation manual. 36en | System overview DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
First use configurationThe Wireless Access Point (DCNM-WAP) includes a web interface wizard to help you with theinitial configuration of the DICENTIS Wireless Conference System.Web browserThe DCNM-WAP web interface is compatible with and optimized for the latest version of theseweb browsers:– Internet Explorer.– Safari.– Firefox.– Opera.– Chrome.Preconditions– All used system devices are prepared and installed as described in the DICENTIS WirelessConference System installation manual. Also see System overview, page 6.– The Wireless Access Point (DCNM-WAP) is powered on.– On a PC/laptop, make sure Windows PC DNS‑SD is installed (DNS‑SD is supplied on themedia delivered with the DCNM-WAP).– On any other device, make sure Apple Bonjour is installed (Download via Apple website). Note: Apple Bonjour or DNS‑SD are not available for Android.– When using WiFi, make sure both 2.4 GHz and 5 Ghz on your device are used to run thebrowser.How to connect the DCNM-WAP1. To connect directly to the DCNM-WAP using WiFi:– Use the WiFi discovery function of you PC/Tablet, and select the DICENTIS WirelessConference System Network Name (SSID): Bosch DICENTIS– Enter the WPA2 key: dcnm-wap– Wait until the connection is made.– Open your web browser and type: http://dcnm-wap.local, in Android type: http://172.27.2.12. To connect directly to the DCNM-WAP using wired:– Open your web browser and type: http://dcnm-wap.local Note: This is not supported on Android, because Android does not support Bonjourand DNS-SD.3. To connect via a network to the DCNM-WAP:– Consult the network owner to obtain the URL or IP address of the DCNM-WAP. 4DICENTIS First use configuration | en 7Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
Initial setup– When the DCNM-WAP is used for the first time (or set to factory defaults) the wizard isshown.– In "Lets get started", select the required language for the web application, and clicksetup device.– In "Country", select the country, the date, the time, the time‑zone, and then click next:–Note: It is illegal to select a country other than the country where the DCNM-WAP isused!– In "User", define a password for the administrator user, and add a user for daily businessuse with the required user rights (see Users, page 17). It is not recommended to use theadministrator user for daily business. Click next.– In "Wifi" the Network name (SSID), WPA2 Key and Host name can be changed. It isrecommended to change the WPA2 Key:– The length of the Network name (SSID) must be between 1 and 25 characters. Thefollowing characters are allowed: A-Z, a-z, 0-9, _, space.– The length of the WPA2 Key must be between 8 and 64 characters.– The length of the Host name must be between 1 and 63 characters. The followingcharacters are allowed: A-Z, a-z, 0-9, -– Click setup device to save these changes.– The wizard is completed and the login page is shown.LoginLog in to the web application1. Enter the correct user name and password, select the required language, and clickLogin.2. The web interface homepage is displayed. See Web interface application, page 10. 4.18en | First use configuration DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Wireless Device initialization1Figure 4.1: DCNM‑WD(E) Wireless Device bottom viewPreconditions Wireless Devices and DCNM-WAP– The DCNM-WAP must be powered on and configured. Refer to First use configuration,page 7, if required.– All Wireless Devices must be:– placed within the range of the DCNM-WAP.– powered on (by inserting the Battery Pack and pressing the microphone requestbutton).– de‑initialized.A Wireless Device is de‑initialized when all LEDs on the Wireless Devices are on. To de-initialize a Wireless Device, use a thin screwdriver to press and hold in the De‑init button onthe base of the Wireless Device (1) until all LEDs are on. Preconditions web interface application– The logged in user must have the access right: Configure system.Initialization1. Log in to the web interface application, and go to the Seats page. Refer to Seats, page20.2. Enable the Subscription mode.3. Press the microphone request button of a Wireless Device.– The Wireless Device starts subscribing, and the LED-bar above the microphonerequest button starts alternating between red and green.– When the LED-bar is off, the Wireless Device is subscribed.4. Wait until a Wireless Device is subscribed before subscribing the next Wireless Device.Subscribing a Wireless Device before the previous device has finished subscribing willresult in overlap.– In overlap, the subscription is disabled for 2 minutes, which is shown in the webinterface application.– Starting subscription before the current overlap time period has finished will restartthe overlap time period of two minutes.– If another WiFi system is in subscription mode, this will also activate the overlapperiod in the DCNM-WAP.5. When all Wireless Devices are subscribed, disable the Subscription mode in the webinterface application. The subscription mode will automatically switch off after 2 minutes.4.2DICENTIS First use configuration | en 9Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
Web interface applicationDepending on user rights, the following buttons are displayed on the web interface homepage:Figure 5.1: Web interface homepage (typical setup)Button Description Access rightManagediscussionTo manage a discussion. See Manage discussion,page 12.Manage meetingPreparediscussionTo prepare a discussion. See Prepare discussion,page 13.Prepare meetingVotingTo use voting. See Voting, page 15.Manage meetingSystemsettingsTo configure the system. See System settings, page16.Configure or modifyusersParticipantsTo set the identification mode for the system.To create participants:– Give participants a name.– Give participants an NFC-ID.– Assign seats to participants.See Participants, page 23.Prepare meeting510 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Button Description Access rightSwitch systemon/off–Switch system on: Switches on the DCNM-WAP. The devices need to be switched onmanually (See Power up in the User manual).–Switch system off: Switches off thesubscribed devices and the DCNM-WAP. Theweb GUI on the DCNM-WAP can still beaccessed.Prepare systemBattery &SignalOverview of:– Wireless Devices battery condition.– WiFi signal strength status.– Range test button and results.See Battery & Signal, page 24.Configure or PreparesystemLoggingOverview and saving of system events. SeeLogging, page 25.ConfigureSystem infoSystem overview. See System info, page 25. ConfigureLogoutExits the discussion application and returns you tothe login page. See Logout, page 25.NoneHomeReturns you to the web interface homepage. NoneBackReturns you to the previous page. NoneMaster volumeOpens the master volume control slider. Controlsthe Wireless Devices loudspeaker volume.Configure or ManagemeetingSee also–Login, page 8–Users, page 17–Seats, page 20–Switch system on/off, page 24 DICENTIS Web interface application | en 11Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
Manage discussionPreconditions:– The logged on user must have the access right: Manage meeting. Click the Manage discussion button on the homepage to open the Manage discussion page.Manage discussion means:– View discussion list: Speakers and waiting participants.– Add, remove, and shift waiting and speaking participants.– Master volume control. Manage discussionThe overview on the left‑hand and right‑hand side, shows the discussion list. This list containswaiting and speaking participants.Use the Shift button to shift participants from Waiting to Speaker. If the speaker list is full,the longest speaking participant is removed from the speaker list.By clicking the Stop and remove all button, all Waiting speakers and Speakers can beremoved from the lists.– Click the + button to select and add participants to the Waiting list or Speakers list.– Click the trash can to remove a seat from the Waiting list or Speakers list.Master volume control buttonClick the master volume control button to adjust the audio output level of the WirelessDevices loudspeaker and Wireless Access Point. 5.112 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Prepare discussionPreconditions:– The logged on user must have the access right: Prepare meeting. To prepare a discussion, click Prepare discussion. This opens the Prepare discussion page.Prepare discussion means:– Define the discussion settings.Prepare a discussion–Discussion mode:–Open: When selected (grey), participants can control their own microphone. If thespeakers list is full, a microphone request is queued in the request list. Auto Shift: When selected, queues in the waiting list are automatically shifted to thespeaker list, if it is not full yet–Override: When selected (grey), participants can control their own microphone. Ifthe speakers list is full, a microphone request overrides the longest speakingparticipant in the list.–Voice: When selected (grey), participants can activate their microphones by speakinginto them. A microphone can be temporarily muted by pressing and holding downthe microphone button.–Push To Talk: When selected (grey), participants can speak by pushing and holdingin their microphone buttons. The microphone is deactivated when the microphonebutton is released. The maximum number of participants that can speak isdetermined by the number of open microphones.–Speakers options:–Maximum number of speakers: Selects the maximum number of speakers in thespeakers list.–Switch microphone off when not used for 30 seconds: This function can be usedwhen participants forget to switch off the microphone manually.–Allow participants to switch off their microphone: When selected, participants areallowed to switch off their microphone.–Show Possible To Speak: When selected, the white light in the Wireless Devicemicrophone request button might be lit. 5.2DICENTIS Web interface application | en 13Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
–Waiting options:–Maximum number of waiting: The maximum number of requests in the waiting listcan be selected here.–Allow participants to remove themselves from the waiting list: When selected,participants can remove themselves from the waiting list.–Show the first in the waiting list on the seat: When selected, the LED on top of theWireless Device microphone that is first in the waiting list will blink green instead ofbeing steady green. Can only be used when Show Possible To Speak is alsoselected. Note: This does not influence the behavior of the button bar LED above themicrophone request buttons.–Priority options:–Priority chime audible: When selected, a priority chime is audible when the devicepriority button is used.–Mute all speakers: When selected (grey), it mutes all speakers temporarily when thedevice priority button is used.–Stop all speakers and remove all waiting participants: When selected (grey), itcancels all speakers and requests when the device priority button is used. 14 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
VotingPreconditions:The logged on user must have the access right: Manage meeting. To manage voting, click Voting. This opens the Manage voting page.Manage voting means:– Define the voting settings, and control the voting round.Define voting settings–Topic: The name of the voting round. This name is also displayed on the touch screen ofthe Wireless Devices Extended when the voting round is opened.–Drop-down menu with answer sets for:– for/against– for/against/abstain– for/against/abstain/dnpv– yes/no– yes/no/abstain– yes/no/abstain/dnpvThe selected answer set is displayed on the touch screen of the Wireless Device Extendedwhen the voting round is opened.Notice!DNPV (Do Not take Part in the Vote) can be selected by participants to indicate that they donot want to take part in the vote. This option is only used for the French language, whereDNPV is abbreviated as NPPV. Control voting round–Open button: Opens the voting round. Once voting is opened, this button changes to theHold button.–Hold button: Puts the voting round on hold. The participants voting buttons aretemporarily disabled and votes cannot be changed or cast. This button changes tothe Resume button when it is pressed.–Resume button: Allows voting to be resumed. Votes can be cast or changed. Thisbutton changes to the Hold button when it is pressed.–Close button: Closes the voting round. 5.3 DICENTIS Web interface application | en 15Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
System settingsPreconditions:– To access system settings and change parameters, the logged on user must have theaccess rights: Configure, and Modify users. Click the System settings button to open the System settings page:Figure 5.2: System settings pageSee also–Users, page 17–Audio, page 17–Cameras, page 18–Seats, page 20–Date and time, page 21–Network and general settings, page 19–System info, page 25–Licensing, page 19–Upgrade, page 21–Participants, page 23–First use configuration, page 7 5.416 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
UsersClick the Users button on the System settings page to open the Users settings page.To add Users, click the + button to open the Add new user screen.To change or remove Users, select a user, and use the edit icons. For each (new) user, the following can be entered or selected:–General: Enter First name, Last name, Username, Password (may be empty).–User rights to be selected (the grey button color means: selected) are for example:–Manage meeting. This right gives access to the Manage discussion and Votingpages. Refer to Manage discussion, page 12 or Voting, page 15.–Prepare meeting. This right gives access to the Prepare discussion and Participantspages. Refer to Prepare discussion, page 13.–Modify users. This right gives access to Users. Refer to Users, page 17.–Configure. This right gives access to the System settings, System info, Logging, andBattery and Signal pages. Refer to System settings, page 16.–Prepare system. This right gives access to the Switch system on/off and Batteryand Signal pages. Refer to Switch system on/off, page 24.AudioClick the Audio button to open the Audio settings page: –System:–Master: Master volume control for the loudspeakers of the Wireless Devices, and theline output of the Wireless Access Point.–Line input/output:–In: Sets the sensitivity of the audio line input of the Wireless Access Point.–Out: Sets the level of the audio line output of the Wireless Access Point.–Routing options I/O: Defines the audio routing mode of the Wireless Access Point:–Recorder: Use this mode to connect an external recorder via the audio line input andaudio line output.–Floor: In this mode, the level of the audio line output is “also” controlled by theMaster.–Mix‑minus: Use this mode to connect an external telephone coupler, or two systems,via the audio line input and audio line output.–Insertion: Use this mode to connect external audio devices, such as audio mixers,and audio processors.–Public Address (PA): In this mode, the level of the audio line output is “not”controlled by the Master.–Feedback Prevention:–Digital Acoustic Feedback Suppression: When selected, enables the DAFS function.–Loudspeaker active when microphone is on: When selected, enables theloudspeaker of the device, when the microphone is on.–Attenuate headphone when speaking: When selected and the microphone is on,attenuates the headphone volume of the Wireless Device 18 dB.–Test Tone: Click the appropriate button to test the audio in the system with a 1 kHz orSweep tone. Click the Off button to stop the test tone.– When Send test tone to loudspeakers is selected, generates the selected test toneto the connected Wireless Devices loudspeaker.5.4.15.4.2DICENTIS Web interface application | en 17Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
– When Send test tone to loudspeakers is selected, generates the selected test toneto the connected Wireless Devices headphone.– When Send test tone to loudspeakers is selected, generates the selected test toneto the audio line output of the Wireless Access Point.EqualizerClick the Equalizer button to open the Equalizer settings page:The Equalizer page is used to set the equalizer settings of the audio line input and output ofthe Wireless Access Point and Wireless Devices loudspeaker.Equalizer filters–Filter 1 type: Shelving filter - A shelving filter for low frequencies with a fixed qualityfactor.–Filter 2, 3, 4 type: Full parametric section - Three full parametric filters with adjustablequality factors, gains and frequencies.–Filter 4 type: Shelving filter - A shelving filter for high frequencies with a fixed qualityfactor.Equalizer settingsProceed as follows to configure a filter:1. Enter the frequency of the filter. Possible values from 50 Hz up to 22 kHz.2. Enter the gain of the filter. Possible values from -12 dB to +12 dB with steps of 0.1.3. Enter the quality (Q) factor of the filter. Possible values from 0.4 to 14 with steps of 0.1.4. Enable or bypass the filter by clicking the checkmark. All changes are immediatelyapplied.CamerasClick the Cameras button to open the Camera settings page:–Overview Camera: Defines the camera used as the overview camera.–Preposition: Defines the preposition camera used for the overview. Only available when aPTZ/Dome camera has been selected as an overview camera (if a fixed camera or None isselected, this field is not visible).–SDI Switcher: Enter the IP address of the HD‑SDI video switcher used. Do not use leadingzeros. If leading zeros are entered, the DCNM-WAP will not be able to control theswitcher.–Example:Correct IP address: 192.168.10.111Incorrect IP address: 192.168.010.111– Overview list: Here all connected cameras are listed. The overview list shows: the Cameraname, Serial number, Software version, camera Type and to which video switcher Inputthe camera is connected to.– The camera Serial number is used as a link to the camera configuration web pages. Note: Only possible if your PC/laptop or tablet device is connected via the wiredEthernet connection of the DCNM-WAP.Notice!Ensure that the Bosch Onvif Camera has firmware 5.80 or higher.– A trash can is displayed next to the Camera name for removing a selected camera.Note: Only a disconnected camera can be removed.5.4.35.4.4 18 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
LicensingClick the Licensing button to open the Licensing page.Licensing is only required when you purchase software licenses.The licensing page provides you with an overview of the activated licenses.Activate a license:To activate software you need to have an activation ID which was send by email afterpurchasing the software license. Activation requires a USB memory stick and any PCconnected to the internet.Note: License activation is not supported for tablets. 1. Insert the USB memory stick into the PC connected to the DCNM-WAP.2. Click the Add license button.3. Enter all required Customer information and Activation ID, click the Add button andthen the Activate button. Note: You can add more than one Activation ID. When allActivation IDs are added, click the Activate button.– A Save as dialog is shown. Save the Request file to your USB memory stick.4. Go to the website https://licensing.boschsecurity.com using a PC/Laptop which isconnected to the internet, and login. If you do not have a username, contact your localBosch representative to acquire an account:– Go to Manage license and upload the request file from the USB memory stick.– Save the Response file to your USB memory stick.5. In the DICENTIS web interface application, click the Process response message button.Select the correct Response file, and then click Open.– Now the license is activated.– New functionality is added and can be used by the system.Returning a licenseThe return license process is started in the license website.1. Log on to https://licensing.boschsecurity.com2. Go to the overview, and find the customer that the license must be returned to.3. Click on the link in the Location column to open the System details pop-up.4. Click the Return License button.– A file will be generated. Save it to a USB stick.5. Go to the license page of the web interface application.6. Click the Process response message button.– Select the correct file, and then click Open.– A save as dialog is shown. Save the file to your USB memory stick.7. Return to the license website, go to Manage license, and upload the Request file fromthe USB memory stick.– Now the license is returned.Network and general settingsClick the Network and general settings button to view the Network and general settingspage. To change theses settings, click the Change network settings button.–Network settings:–Network Name (SSID): Bosch DICENTIS (factory default).–WPA2 Key (password): dcnm-wap (factory default).–Channel: Shows the currently selected WiFi channel. This channel is automaticallydefined by the system and cannot be changed.5.4.55.4.6DICENTIS Web interface application | en 19Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
–Hostname: Enter the network name of the DCNM-WAP. The default name isdcnm‑wap.–Change network settings button: Click this button to open the change settingsscreen. Change the settings, if required, and click either the Cancel or Save button.–General settings:–DCNM‑WDE GUI language: Select the GUI language for the DCNM-WDE WirelessDevices touch screen.–Show custom logo on DCNM‑WDE: When selected, the custom logo will be visibleon the Wireless Devices (DCNM-WDE) touch screen.–Factory default button: Click the button to reset the Wireless Access Point to factorydefault settings and values. Important: Make sure all Wireless Devices are switchedon and are in range before you activate the factory default because all WirelessDevices will be de-initialized. After a factory default, all settings are returned to theirdefault value, and all Wireless Devices need to be subscribed.SeatsClick the Seats button to open the Seats settings page.Here the Wireless Devices can be assigned to seats:–Seats overview:–Select: The header of this column shows the number of known seats and the numberof connected seats. If a seat is disconnected, the disconnect symbol is displayed tothe left of the seat row.–Seat name: Change the seat name.–Prio: When selected, the participant is able to use the Wireless Device priority(chairperson) button.–Dual: When selected, the Wireless Device is configured for dual-use.Note: A device cannot be prio and dual simultaneously, so when Prio is selected, thedual checkbox is disabled.–ID: When selected, the identification feature is enabled. Participants can use an NFCtag to identify themselves at the Wireless Device Extended.–Voting: When selected, the voting feature is enabled. Participants can cast their voteat the Wireless Device Extended.–Serial nr: The serial number of the connected Wireless Device.–Camera: The camera name connected to the seat. Only available when the cameracontrol license is installed.–Pre‑position: Camera preposition setting number assigned to the seat. Only availablewhen the camera control license is installed.–Selection mode: When selected, a Wireless Device can be located by clicking the Selectsymbol to the left of the seat row. The red microphone LED on the selected WirelessDevice will illuminate to indicate its position in the conference room.–Subscription mode: When selected, a Wireless Device not associated with a DCNM-WAP,can be associated with this DCNM-WAP by pressing the request button on the wirelessdevice. A new seat will be assigned to this device and added to the seats overview. Referto Wireless Device initialization, page 9.–De‑init button: When clicked, it erases the subscription of all Wireless Device. All LEDs onthe Wireless Device are on when the Wireless Device does not have a subscription.–Remove disconnected seats button: Removes all seats which are currently not connectedto the system. 5.4.720 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Date and timeClick the Date and time button to open the Date and time settings page:Click the Change date and time settings button to select:–Date: Select the current date.–Time: Select the local time.–Time zone: Select the local time zone from the list.Notice!The DCNM-WAP can automatically synchronize the date and time with a internet time server.If the internet is not available, the DCNM-WAP tries to synchronize with a time server which isoffered by the DHCP server. If the time server can not be reached, the date and time can beset manually. If a time server becomes available the DCNM-WAP will synchronize the date andtime. UpgradeNotice!Upgrade is not available on tablets. Click the Upgrade button to open the software Upgrade page.The Upgrade page is used to:– upgrade/maintain the software of the Wireless Access Point (DCNM-WAP) and WirelessDevices (DCNM-WD and DCNM-WDE).– upload the custom logo to the Wireless Device Extended (DCNM-WDE). 1. From the product related information page on www.boschsecurity.com, download theupgrade software file. Each device will have its own file:– Always start with upgrading the Wireless Devices.– Upgrade the DCNM-WAP last.2. From the Upgrade page, click in the File box to select your saved software file.3. The web interface application will automatically select the correct devices, depending onthe selected file. If you do not want to upload firmware to a particular device, uncheckthe checkbox for that device.4. Click the Start button to start the upload process:–Progress bars are displayed indicating the upload process.– The upload status is shown in the State column (Idle, Programming, Rebooting,Done or Failed after reboot). If the upgraded file is corrupt or not recognized, anerror message is displayed.– Software versions (numbers) are shown in the Version column. The uploadedsoftware version number is only shown when the upgrade process is successful.– As soon as the DCNM-WAP is upgraded, it will reboot.5. Exit the Upgrade page after completion of the upload process (Done state). 5.4.8 5.4.9 DICENTIS Web interface application | en 21Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
Notice!When downgrading DCNM-WD(E)s, they will become disconnected from the Wireless AccessPoint, and the upgrade page cannot correctly indicate when the downgrade has finished. AWD(E) can be subscribed again when the yellow LEDs on the WD(E) come on. Notice!If you need to downgrade the DCNM-WAP, make sure you de‑initialize all Wireless Devicesfirst. Upload custom logoThe custom logo can be uploaded to the Wireless Devices (DCNM-WDE) in the same way asupgrade software. The following conditions apply:– The filename must start with DCNM-WDE– Only upload PNG files with dimensions of 480 x 272 pixels. Other file formats and dimensions are not supported. 22 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
ParticipantsPreconditions:– The logged on user must have the access right: Prepare meeting. Click the Participants button to open the Participants and identification settings page.Participants can be assigned seats and/or can use an NFC tag to identify themselves to thesystem. When a participant is identified by the system, the name of the participant is shown inthe speaker list and waiting list. The following items can be set on this page:Identification–Off (grey):– Participant names are not used and are not shown in the speaker list and waitinglist.– Participants cannot use an NFC tag to identify themselves.–By assignment (grey):– Seats must be assigned to participants. If a seat is not assigned to a participant, thatseat cannot be used.– Participants cannot use an NFC tag to identify themselves.– A seat can be used without having to identify the participant, by assigning a dummyparticipant with a general name to a seat.–At assigned seat (grey):– Seats must be assigned to participants. If a seat is not assigned to a participant, thatseat cannot be used.– Participants must use an NFC tag to identify themselves at the assigned seat.– If a participant tries to identify him/herself at another seat, a message is displayedon the Wireless Device to inform the participant that they are at the incorrect seat.– The seat cannot be used until the assigned participant is identified at the seat.–At any seat (grey):– Participants can use an NFC tag at any seat to identify themselves.– The seat cannot be used, until a participant has been identified at that seat.Participants overview–Trash can: Removes the selected participant.–Name: The participants (editable) name.–NFC‑ID: The number of the Near Field Communication (NFC) tag of the participant.–Seat: Selects the seat name, from the list, that the participant is assigned to. 5.5DICENTIS Web interface application | en 23Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
Switch system on/offPreconditions:– The logged on user must have the access right: Prepare system. Use the Switch system on/off button to set the system in the “power on” or “power off”mode:– Click the Switch system on button to set the system in the “power on” mode.– Press the microphone request button of a Wireless Device to switch it on.Note: The Wireless Devices have to be switched on individually. – Click the Switch system off button to set the system in the “power off” mode. This willswitch off all Wireless Devices.–Note: If you try to switch on a Wireless Device, by pressing the microphone requestbutton when the system is in the “power off” mode, the device will momentarily switchon and then switch off.Battery & SignalPreconditions:– The logged on user must have the access right: Configure or Prepare system. Click the Battery & Signal button to open the Battery and Signal overview page. The following information is shown for each seat that is currently connected to the WirelessAccess Point: Note: If a seat is disconnected, the disconnect symbol is displayed to the left of the seat row,and the data in the seat row is not displayed.–Seat: The seat name.–Battery: Indicates the remaining power supply capacity, in hours, of the Wireless DeviceBattery Pack.Note: After replacing a battery or powering up a Wireless Device, the number of batteryhours displayed might be higher that the actual life of the battery. This value will stabilizeafter a short while.–Charges: Shows the number of times the Battery Pack battery is charged.–Signal: Indicates the WiFi signal strength, in dBm.–Test: This column shows the result of the range test.– Press the button to Start the range test. The system DCNM-WAP starts to measure ifall Wireless Devices are in range of several frequencies. This guarantees that theWireless Devices will continue to work if the DCNM-WAP decides to switch toanother WiFi channel in case of interference.–Serial number: The serial number of the Battery Pack. 5.65.724 en | Web interface application DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
LoggingPreconditions:– The logged on user must have the access right: Configure. Click the Logging button to open the Logging page.– Click the Clear view button to clear all events.– Click the Export button to export and save the current event logging overview file (*.txtformat).Notice!Logging export is not available for tablets.System infoPreconditions:– The logged on user must have the access right: Configure. System info is used by a technician. When the System info button is clicked, the followingsystem information is shown on the System info page:–Ethernet MAC and IP address.–Wireless IP address.– Software Versions.LogoutPreconditions:– None Click the Logout button to log out, which returns you to the Login page.5.85.95.10DICENTIS Web interface application | en 25Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
Wireless Access Point LED behaviorThe LEDs on the front panel of the Wireless Access Point (DCNM-WAP) give information on the(configuration) status of the Wireless Access Point.A B C C B AFigure 6.1: DCNM-WAP status LEDs Blue (A) Red (B) Blue (C) DescriptionFlashing Off Off – No DCNM-WD(E) connected yet.– Subscription mode is off.On Off Off – At least one DCNM-WD(E) is connected.– Subscription mode is off.Flashing Flashing Flashing – The DCNM-WAP is starting‑up.On Flashing Off – DCNM-WAP software upgrade active.On Flashing On – DCNM-WD(E)s software upgrade active.Flashing Off On – Subscription mode is on.– No DCNM-WD(E)s connected yet.On Off On – Subscription mode is on.– At least one DCNM-WD(E) is connected.Off Flashing Off – System is in Power off mode.Off Off Off – No DC power supply connected.Table 6.1: Status LEDs626 en | Wireless Access Point LED behavior DICENTIS2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
TroubleshootingCustomer serviceIf a fault cannot be resolved, please contact your supplier or system integrator, or go directlyto your Bosch representative.77.1DICENTIS Troubleshooting | en 27Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |
Bosch Security Systems B.V.Torenallee 495617 BA EindhovenThe Netherlandswww.boschsecurity.com© Bosch Security Systems B.V., 2015

Navigation menu