Bosch Security Systems M531 Licensed Non-broadcast transmitter worn on body User Manual

Bosch Security Systems, Inc. Licensed Non-broadcast transmitter worn on body Telex Model TR 1 Beltpack

a href="https://usermanual.wiki/Bosch-Security-Systems" itemprop="url"> Bosch Security Systems >

MANUAL 2 1

Telex Model TR-82N Beltpack Owners / Users Manual (Preliminary Information) General Description: The Telex model TR-82N beltpack transceiver is a component of the BTR-80N wireless intercom system. The TR-82N is intended for use as a belt worn wireless full duplex portable intercom radio for use in a professional installation such as television or cinema production. Each BTR-80N base station can be used with one to four TR-82N beltpacks. The TR-82N transmits within the 614 to 722 MHz range (TV Channels 38-55). It receives in the 482 to 608 MHz range (TV Channels 16-36). The TR-82N transmitter operates on a single frequency within an 18 MHz wide section of the transmit frequency range. The receiver also operates on a single frequency within an 18 MHz wide section of the receiver frequency range. The RF coverage range of the TR-82N communicating to a base station may be up to 200 meters (656 ft). The transmitter has three selectable conducted output power output levels; 5mW, 50mW and 100 mW. The transmit power can also be set to automatically reduce to the above listed power levels when the unit is close-in to the base station to aid in intermodulation reduction and unnecessary transmit power. Operating frequencies can be selected from pre-set groups or the user can select special operating frequencies within the 18 MHz wide allotments. The LCD display and buttons are located on the back panel. From the LCD display and buttons the following menus may be obtained: • Group and Channel • Transmit Frequency • Receive Frequency One • Receive Frequency Two • Microphone Gain Setting • Battery Life • Transmit power level (5mW, 50mW 100mW or Auto between the values) • Receiver Squelch Level • Push-to-Talk / Push-to-TX mode • Headset configuration settings • Top Panel LEDs on or off. The on/off/volume controls, low battery indicator, microphone overmod. light, audio channel 1 or 2 button and lights, wireless talk around (WTA) and stage announce (SA) buttons are located on the top panel. Transmit and receive antennas are attached to the TR-82N. Either or both unscrew for field replacement but are not coaxial connectors. The TR-82N beltpack can be powered by AA Alkaline or a Nickel-Metal Hydride Battery pack. Page 1 of 3
Controls and Connections 1. ON/OFF & Volume Control – Either interom 1 or intercom 2 knob turns beltpack on. Both knobs must be off to turn the unit off. 2. WTA Button and Light – Wireless talk button. When pressed, the user’s audio is disconnected from the wired intercom at the base station. 3. SA Button and Light – Wireless talk button. When pressed, the user’s audio is routed to the stage annouce connector on the back of the base station. The user also loses their sidetone as an indication that stage announce is activated. 4. Audio Channel Select Buttons and Lights –Allows the user to select either audio channel 1 or 2. 5. BAT/O.M. Light – Battery - Light flashes on power up = Battery OK Light on continuously = Battery Low Light does not flash or come on = Battery Dead Microphone Lvl: Light flashes on loudest speech = Gain OK Light flashes on all speech = Gain too High Light never flashes on loudest speech = Gain too Low 6. Talk Buttons and Lights – LED is on when a talk button, SA or WTA is active. Press a button to enable the audio path from the headset. Software Selectable modes: Push-to-Talk Push-to-Latch 1. [MENU] and [SET] buttons – Used to select menus and set options on the LCD. 2. LCD display. 3. [UP] and [DOWN] buttons - Used to select menus and set options on the LCD. 4. Programming Connector – Used to update flash in unit. 5. Headset Connector – XLR Plug for Telex units, XLR Receptacle for RTS units. 6. Battery Latch – Press down to enable the battery pack to be released. While the latch is held down, slide the battery pack about 1/8 inch back, toward the latch, until it stops, then lift out. 7. Receive Antenna – The antennas are screw type, ¼ wave, replaceable antennas. The color dot on the screw end of the antenna must match color dot on antenna receptacle. 8. Transmit Antenna – The antennas are screw type, ¼ wave, replaceable antennas. The color dot on the screw end of the antenna must match color dot on antenna receptacle. Page 2 of 3
Download:
Mirror Download [FCC.gov]
Document ID989334
Application IDre93tabbPIzDQVT7ossQ2w==
Document DescriptionMANUAL 2 1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize8.62kB (107719 bits)
Date Submitted2008-08-25 00:00:00
Date Available2008-09-23 00:00:00
Creation Date2008-08-04 13:42:44
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2008-08-04 13:43:51
Document TitleTelex Model TR-1 Beltpack
Document CreatorAcrobat PDFMaker 7.0.7 for Word
Document Author: Jim Andersen
FCC ID Filing: B5DM531

Navigation menu