Boss Audio Systems Phantom Ph3000D Users Manual Class D Amp 2

PH3000D to the manual 9e837ec7-9f33-49b0-bf4c-32236c02f948

: Boss-Audio-Systems Boss-Audio-Systems-Phantom-Ph3000D-Users-Manual-475811 boss-audio-systems-phantom-ph3000d-users-manual-475811 boss-audio-systems pdf

Open the PDF directly: View PDF .
Page Count: 11

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes NotesNotes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes NotesNotes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

With the PHANTOM Class D

amplifier series, we are introducing

three new CLASS D amplifiers, all

designed in the USA.

These PHANTOM models feature

variable low pass and subsonic filters

and a variable input gain control.

These amplifiers also incorporate a

phase selector switch to help

compensate for time delays in

subwoofer applications.

For further flexibility in the use of a

subwoofer, a variable 0-+18dB Bass

Boost control has been included.You

can control the subwoofer level with

the remote level control module.

understands that amplifiers are

placed in many different kinds of

installations, so we have also

included an input sensitivity control

to help you integrate the amp into

your system regardless of the nature

of your input source.

A special feature on this Class D amp

is DataLink circuitry, which allows

you to “strap” together (for example)

two PH5000D’s for an astounding

total maximum output power of

10,000 watts.

Features

Your new PHANTOM amplifier features

the following:

• Class D operation

• MOSFET PWM (Pulse Width

Modulated) Power Supply

• One Ohm stable mono operation

• Thermal, overload and speaker

short protection

• Soft turn-on circuit

• Remote turn-on/turn-off circuit

• Variable input gain control

• Input voltage sensitivity selector

• Variable subsonic filter: 15-40 Hz,

12dB/octave

• Variable low pass filter: 50-150 Hz,

12dB/octave

• Variable 0-+18dB Bass Boost

• 0/180º Phase Shift selector

• Gold-plated RCA low level inputs

• Nickel-plated speaker and power

terminals

• LED power and protection

indicators

• Black anodized heatsink

• Remote subwoofer level control

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

Installation precautions

Before you drill or cut any holes,

investigate your car's layout very

carefully. Take special care when you

work near the gas tank, fuel lines,

hydraulic lines and electrical wiring.

Never operate the amplifier when it is

unmounted. Attach all audio system

components securely to prevent

damage, especially in an accident.

Before making or breaking power

connections in your system, disconnect

the vehicle battery. Confirm that your

head unit or other equipment is turned

off while connecting the input jacks and

speaker terminals.

If you need to replace the power fuse,

replace it only with a fuse identical to

that supplied with the amplifier. Using

a fuse of a different type or rating may

result in damage to your audio system

or your amplifier which is not covered

by the manufacturer's warranty.

Mounting the amplifier

1. Find a suitable location in the vehicle

in which to mount the amplifier.

2. Make sure there is sufficient air

circulation around the intended

mounting location.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

General precautions

Before installing and using your new

amplifier, please become fa-

miliar with all the information con-

tained in this manual.

Please keep this manual in a safe

place for future reference.

• Do not open or attempt to repair this

unit yourself. Dangerous high voltages

are present which may result in electric

shock. Refer any repairs to a qualified

service technician.

• To avoid risk of electronic shock or

damage to the amplifier, do not permit

any of this equipment to become damp

or wet from water or drinks. If this does

occur, immediately unplug the power

wires and send the amplifier to your

local dealer or service center as soon

as possible.

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

What is included?

When first unpacking your new

amplifier, please check first that the

package contains all of the items

below. If something is missing, contact

the store where you purchased the

amplifier.

• Class D amplifier

• Remote subwoofer level control

• Remote subwoofer control cable

• DataLink cable (for strapping two

identical PHANTOM

Class D amps together)

• Four (4) mounting screws

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

Before doing any wiring, look through

this manual and identify the diagrams

to follow for power, input and speaker

connections for your particular

installation. Be sure you understand

all the connections before you proceed.

1. Connect the amplifier’s power

ground terminal to the closest point

on the chassis of the car. Keep this

ground wire to less than 39" (100 cm)

in length. Use 4 gauge (or heavier)

wire.

2. Connect the remote terminal to the

remote output of the head unit using

16 gauge (or heavier) wire.

3. Connect an empty fuse holder within

18" (45 cm) of the car battery, and run

4 gauge (or heavier) cable from this

fuse to the amplifier location.

The purpose of placing a fuse in this

location is to protect your vehicle’s

battery in the event that this wire

accidentally touches the chassis

ground on its run to the amplifier.

Connecting the amplifier

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

SHOCK HAZARD! Do not open the case

of this product. There are dangerous

voltages present within the unit. There are

no user-serviceable parts within the unit.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

When making electrical connections

to the amplifier, please observe the

following:

• Always use 4GA or heavier wire for

power and ground connections.

• Wire the amplifier directly to the car

battery. Make sure there is circuit

protection (such as a fuse) on the

positive power lead within 18” of the

battery.

• When making a ground connection,

always use the shortest possible wire

to a good chassis ground point.

• Wire the remote turn-on connection

to the remote turn-on lead of your EQ

or head unit. In some cases, this may

be the power antenna lead of the head

unit.

• Fuses protect BOTH the amplifier

and the electrical system of your

vehicle from faulty conditions. If you

must replace a fuse on the amplifier,

you must use a fuse of exactly the

same type and rating. A different type

of fuse or rating may result in damage

or cause a fire.

Tips for making your system

as safe as possible Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

Do not mistake the input level control

for a volume control! It is designed

ONLY to match the output level of

your audio source to the input level

of your amplifier.

Do not adjust this input level to

maximum unless your input level

requires it.

Ignoring these instructions will result

in an input overload to the amplifier,

and excessive audio distortion. It

can also cause the protection circuit

to engage.

Don't misuse the

level control!

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low Level Input Wiring

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

INPUT

LEVEL

min

max

SUBSONIC

FILTER

15Hz

40Hz

BASS

BOOST

0

+18dB

LOW PASS

CROSSOVER

50Hz

150Hz

PROTECTION

PHASE SHIFT

0180º

SLAVE

MASTER

DATA LIN K

AMP MODE

INPUT SENSITIVITY

100mV-2V

2V-8V

R

L

R

L

INPUTSLINE OUT

SPEAKER

CLASS D MONO BLOCK POWER AMPLIF IER

POWER

INPUT

LEVEL

min

max

SUBSONIC

FILTER

15Hz

40Hz

BASS

BOOST

0

+18dB

LOW PASS

CROSSOVER

50Hz

150Hz

PROTECTION

PHASE SHIFT

0180º

SLAVE

MASTER

DATA LIN K

AMP MODE

INPUT SENSITIVITY

100mV-2V

2V-8V

R

L

R

L

INPUTSLINE OUT

SPEAKER

CLASS D MONO BLOCK POWER AMPLIF IER

POWER

INPUT

LEVEL

min

max

SUBSONIC

FILTER

15Hz

40Hz

BASS

BOOST

0

+18dB

LOW PASS

CROSSOVER

50Hz

150Hz

PROTECTION

PHASE SHIFT

0180º

SLAVE

MASTER

DATA LINK

AMP MODEINPUT SENSITIVITY

100mV-2V

2V-8V

R

L

R

L

INPUTSLINE OUT

SPEAKER

CLASS D MONOBLOCK POWER AMPLI FIER

POWER

SPEAKER

IMPEDANCE

1-8 OHMS

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

+12V

POWER CONNECTIONS

GND

REMOTE

FUSES

REMOTE SUBWOOFER

LEVEL CONTROL

+12V

POWER CONNECTIONS

GND

REMOTE

FUSES

REMOTE SUBWOOFER

LEVEL CONTROL

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

to REMOTE TURN-ON

terminal of head unit

Chassis ground point

Battery

FUSE

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

to REMOTE TURN-ON

terminal of head unit

Battery FUSE

Distribution

Block

Chassis

ground

point

Stiffening

Capacitor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

INPUT

LEVEL

min

max

SUBSONIC

FILTER

15Hz

40Hz

BASS

BOOST

0

+18dB

LOW PASS

CROSSOVER

50Hz

150Hz

PROTECTION

PHASE SHIFT

0180º

SLAVE

MASTER

DATA LINK

AMP MODE

INPUT SENSITIVITY

100mV-2V

2V-8V

R

L

R

L

INPUTSLINE OUT

SPEAKER

CLASS D MONO BLOCK POWER AMPLIF IER

POWER

INPUT

LEVEL

min

max

SUBSONIC

FILTER

15Hz

40Hz

BASS

BOOST

0

+18dB

LOW PASS

CROSSOVER

50Hz

150Hz

PROTECTION

PHASE SHIFT

0180º

SLAVE

MASTER

DATA LINKAMP MODE

INPUT SENSITIVITY

100mV-2V

2V-8V

R

L

R

L

INPUTSLINE OUT

SPEAKER

CLASS D MONO BLOCK POWER AMPLIF IER

POWER

SLAVE

MASTER

AMP MODE

SLAVE

MASTER

AMP MODE

SUBWOOFER

Speaker

+

–

SPEAKER

IMPEDANCE

2-8 OHMS

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

PLEASE NOTE:

In this MASTER AMP/SLAVE AMP

configuration, the Slave amp

receives its audio signal from the

Master Amp. Therefore, DO NOT

USE THE INPUTS ON THE SLAVE

AMP!

INPUT

LEVEL

min

100mV-2V

R

L

INPUTSLINE OUT

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

+12V

POWER CONNECTIONS

GND

REMOTE

FUSES

REMOTE SUBWOOFER

LEVEL CONTROL

+12V

POWER CONNECTIONS

GND

REMOTE

FUSES

REMOTE SUBWOOFER

LEVEL CONTROL

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

to REMOTE TURN-ON

terminal of head unit

Chassis

ground

point

Battery FUSE

Distribution

Block

Chassis

ground

point

Stiffening

Capacitor

Chassis

ground

point

Remote Subwoofer

Level Control

REMOTE SUBWOOFER

LEVEL CONTROL

Chassis

ground

point

PLEASE NOTE:

In this MASTER AMP/SLAVE AMP

configuration, the Slave amp

receives its audio signal from the

Master Amp. Therefore, DO NOT

USE THE SUBWOOFER LEVEL

CONTROL ON THE SLAVE AMP!

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Amplifier will not

power up.

Check to make sure you have a good ground connection.

Check that the Remote Input (Turn-On) has at least 3VDC.

Check that there is battery power on the (+) terminal.

Check that there is at least 12v.

Check all fuses, replace if necessary.

Make sure that the Protection LED is not illuminated. If it is lit, shut off

the amplifier briefly, and then repower it.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

No output. Check that all fuses are OK.

Check that amplifier is properly grounded.

Check that the Remote Input (Turn-On) has at least 3VDC.

Check that the RCA audio cables are plugged into the proper inputs.

Check all speaker wiring.

Low output. Reset the Level Control.

Check the Crossover Control settings.

Audio present in

only one channel.

Check the RCA interconnect cables.

Check all speaker wiring.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound.Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

MODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

Troubleshooting

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 10

Specifications

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 11

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 6

CONTENTS

U S E R ’ S M A N U A L

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 4

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 3

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 8

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 5

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 7 PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 9

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 2

Introduction

Important installation

considerations for using

this amplifier.

Notes Notes Notes

If you experience operation or performance problems with this product, compare your

installation with the electrical wiring diagram on the previous pages. If problems persist,

read the following troubleshooting tips which may help eliminate the problems.

Low-level (RCA) input wiring is preferred for best audio performance. Always use

a high-quality RCA cable for best audio performance.

Protection LED

comes on when

amplifier is

powered up.

Check for short circuits on speaker leads.

Turn down the volume control on the head unit to prevent overdriving.

Remove speaker leads, and reset the amplifier. If the Protection LED still

comes on, then the amplifier is faulty and needs servicing.

High hiss in the

speakers.

Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then

plug in the component driving the amplifier and unplug its inputs. If the

hiss disappears at this point, go on until the faulty/noisy component is

found.

It is best to set the amplifier's input level control as low as possible. The

best subjective signal-to-noise ratio is achieved in this manner. Try to set

the head unit as high as possible (without distortion) and the amp input

level as low as possible.

Squealing noise

from speakers.

Check for improperly grounded RCA interconnects.

Distorted sound. Check that the Input Level Control is set to match the signal level of the

head unit. Always try to set the Input Level as low as possible.

Check that all crossover frequencies are properly set.

Check for short circuits on the speaker leads.

Amplifier gets

very hot.

Check that the minimum speaker impedance for the amp model is correct.

Check that there is good air circulation around the amp. In some

applications, it may be necessary to add and external cooling fan.

Engine noise

(static type)

This is usually caused by poor quality RCA cables,which can pick up

radiated noise. Use only the best quality cables, and route them away

from power cables.

Engine noise

(alternator

whine)

Check that speaker leads are not shorted to the vehicle chassis.

Check that the RCA grounds are not shorted to the vehicle chassis.

Check that the head unit is properly grounded.

The fuse ratings for these amps is:

PH3000D: 50A (25A x 2)

PH4000D: 105A (35A x 3)

PH5000D: 140A (35A x 4)

Although sufficient for normal working

conditions, overloading the amp may

result in blown fuses. Please try to

avoid overloading the amp in this

manner.

Your PHANTOM Class D am-

plifier is designed to run with

a minimum load of 1 Ohm.

Operating the PH3000D,

PH4000D or PH5000D with a

speaker impedance load be-

low 1 Ohm may result in poor

sound quality and damage to

the amplifier circuitry. Such

damage is not covered under

the warranty for this product.

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

MASTER

AMPLIFIER

Front panel

SLAVE

AMPLIFIER

Front Panel

Power Connections

Without Stiffening Capacitor

With Stiffening

Capacitor

Bridging Two PH5000D, PH4000D or PH3000D Amplifiers

SLAVE

AMPLIFIER

Rear Panel

FRONT PANEL CONNECTIONS REAR PANEL CONNECTIONS

• If there is smoke or any peculiar odor

present during use or if there is damage

to any of the component enclosures,

immediately unplug the power cord

and send the amplifier to your local

dealer or service center as soon as

possible .

3. Mark the location for the mounting

hole screws by positioning the amplifier

where you wish to install it. Use a scribe

or mounting screw, inserted through

each of the amp's mounting holes, to

mark the mounting surface. If the

mounting surface is carpeted, measure

the hole centers and mark with a felt

tip pen.

4. Drill pilot holes in the mounting

surface for the mounting screws. Place

the amplifier in position, and attach

the amplifier to the mounting surface

securely using screws.

4. Check that the fuse holder is empty.

Then connect the fuse holder to the

"BATT+" connection on the amplifier.

5. If multiple amplifiers are being used

in your system, either:

• Run a separate pair of cables from

the battery and a chassis ground point

to each amplifier. Each (+) cable must

have its own inline fuse.

-or-

• Run a #0 cable from the fuse holder

at the battery to a distribution block

at or near the amplifier's location. Then

run separate cables from the amplifier

to this distribution block and to

independent chassis ground points.

6. Connect all line inputs and outputs

(if used) using high-quality cables.

Connect all speakers, following the

diagrams in this manual. Be sure to

observe proper polarity to avoid audio

phase problems.

7. Insert fuse(s) into the battery fuse

holder(s).

8. Recheck all connections before

powering up the amplifier.

9. Set all level controls to minimum

position, and set all crossover

controls/switches to the desired

frequency points.

10. Power up the head unit and the

amplifier. Then set the volume control

on the head unit to about 3/4 volume,

and adjust the amplifier’s input level

control(s) to just below the level of

distortion.

11. Further fine tuning of the various

controls may be necessary to obtain

best results.

Speaker Connections

MASTER

AMPLIFIER

Rear panel

SUBWOOFER

Speaker

2Introduction

2Features

3What is included?

3General precautions

3Installation precautions

3 Mounting the amplifier

4 Connecting the amplifier

5Important system considerations

5Tips for a safe system

6Low level input wiring

6Speaker wiring

7Power connections

Normal and with Stiffening Capacitor

8Bridging two PHANTOM

CLASS D Amplifiers

10 Troubleshooting

11 Specifications

Congratulations on your

purchase of a

PHANTOM Class D Amplifier.

It has been designed, engineered

and manufactured to bring you

the highest level of performance

and quality, and will afford you

years of listening pleasure.

Thank you for making

your choice for car audio

entertainment!

1600W x 1

3000W x 1

4000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 3

15" (381mm)

All specifications subject to

change without notice.

RMS POWER

into 4 Ohms

MAX POWER

into 2 Ohms

MAX POWER

into 1 Ohm

Min. speaker

impedance

Input

impedance

Input

sensitivity

Frequency response

Signal-to-noise ratio

Crossover/filter range

low pass

subsonic

Bass Boost

Phase Shift

Fuse rating

Dimensions:

9-1/2" x 2-1/4" x ...

(241mm x 57.2mm x...)

1800W x 1

3500W x 1

5000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

40Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

35A x 4

18" (457mm)

PH3000DMODEL

page

PH5000D

PH4000D

PH3000D

CLASS D MonoBlock

Car Audio Amplifiers

CLASS D MonoBlock Car Audio Amplifiers

PH4000D

1200W x 1

2200W x 1

3000W x 1

1 Ohm Mono

10k Ohm

Selectable 100mV-2V or 2V-8V

50Hz-150Hz

100dB

50Hz-150Hz

15Hz-40Hz

Variable 0 -+18dB

Selectable 0/180º

25A x 2

13" (330mm)

PH5000D

SYMPTOM POSSIBLE REMEDY

PH3000D/PH4000D/PH5000D Amplifier User’s Manual - page 1

PH3000D/PH4000D/PH5000D

AMP MODE

SWITCH IN SLAVE

POSITION

AMP MODE

SWITCH IN MASTER

POSITION

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

To Audio Inputs of

satellite amplifier

(if present)

To Audio Outputs of head

unit or Subwoofer outputs

of a signal processor

Chassis

ground

point

FUSE

15