Bowflex Revolution Accessory Rack Owner S Manual BFX_Revo_FLEX Rack_ RevB_AM_0706_

Assembly Manual BFX_Revolution_Flex_Rack_AM_RevB_web Bowflex Product Manuals | Bowflex

2014-07-05

: Bowflex Bowflex-Bowflex-Revolution-Accessory-Rack-Owner-S-Manual bowflex-bowflex-revolution-accessory-rack-owner-s-manual bowflex pdf

Open the PDF directly: View PDF .
Page Count: 12

Accessory Rack

Assembly Instructions

P/N 001-6931 RevB (07/2006)

Safety Requirements ..........................................................3

Product Specifications ......................................................3

Complete Rack Component Diagram ..............................4

Parts List ...............................................................................4

Assembly Steps ...................................................................5

Storing Your Accessories ..................................................9

Warranty Information .......................................................10

Contact Information .........................................................11

Table of Contents

Safety Requirements











Used to call attention to POTENTIAL hazards that could result

in personal injury or damage to equipment.

IMPORTANT SAFETY INSTRUCTIONS

The following deﬁnition applies to the word “Caution” found throughout this manual:

• Always read and follow the Safety labels attached

to your Bowﬂex Revolution™ Accessory Rack. Do

not remove these labels. If you need replacement

labels, please call a Nautilus Representative at 1-

800-NAUTILUS (628-8458).

• Read the manual and follow it carefully before

using the rack.

• Never allow children to use the Bowﬂex

Revolution™ Accessory Rack unsupervised. To do

so could result in injury. This equipment is under no

circumstances suitable as a children’s toy.

• Inspect your rack for any worn or loose

components prior to use. Tighten or replace any

worn or loose components prior to use.

• Set up and use your Bowﬂex Revolution™

Accessory Rack on a hard, level surface.

• Use your Bowﬂex Revolution™ Accessory Rack

ONLY to store accessory equipment for your

Bowﬂex Revolution™ home gym. Store each

accessory only in its designated holder on the rack.

READ ALL INSTRUCTIONS BEFORE USING THE EQUIPMENT.

Product Specifications

Dimensions: 31" L x 29" W x 37" H (79cm x 74cm x 94cm)

Assembled Unit Weight: 46.2 lbs. (21 kg)

Shipping Package Weight: 51.7 lbs. (23.5 kg)

Parts

# Qty. Description

1 1 BASE SUPPORT

2 1 BASE BRACKET

3 1 CURL BAR HOOK, RIGHT

4 1 CURL BAR HOOK, LEFT

5 1 MOUNT, PREACHER CURL ASSEMBLY

6 1 BASE PLATE

7 1 CROSS MEMBER

8 4 SEAT BRACKET

9 1 FLEX BAG

10 1 RODS - (4 ROD PACK ASSEMBLY)

11 1 LEFT TUBE

12 1 RIGHT TUBE

13 9 3/8" X 7/8" ALLEN BOLT

14 16 3/8" X 2 3/4" ALLEN BOLT

15 16 3/8" NYLOCK NUT

16 41 M10 or 3/8" WASHER

Complete Rack Component Diagram

Tools Required

7/32" Allen Wrench (included)

You will also need:

9/16" Socket Wrench

9/16" Wrench or Adjustable Wrench

Utility knife or scissors to cut nylon ties

Hardware

2 3/4" Allen Bolt

Washer

Lock Nut

7/8" Allen Bolt





































step

Figure 1











Parts:

• Base Plate (#6)

• Seat Bracket (#8)

• Preacher Curl Mount (#5)

Hardware Qty

• 7/8" Bolts (#13) 5

• Washers (#16) 5

Tools:

• Allen wrench (7/32”)

1-1 Attach the Seat Bracket (#8) to the Base Plate (#6)

using the hardware as shown in Figure 1.

1-2 Attach the Preacher Curl Mount (#5) to the Base

Plate using the hardware shown in Figure 1.

Tighten hardware completely.

Figure 2













Parts:

• Left Tube (#11)

• Right Tube (#12)

• Base Bracket (#2)

Hardware Qty

• 2 3/4" Bolts (#14) 4

• Washers (#16) 8

• Nuts (#15) 4

Tools:

• Allen wrench (7/32”)

• Wrench/Socket (9/16”) or Open End Wrench

2-1 Attach the Base Bracket (#2) to the Left Tube

(#11) and Right Tube (#12) using the hardware

as shown in Figure 2. Make sure that the large

holes on the Tube uprights are facing away from

the Base Bracket.

Note: Do not tighten hardware at this time.

step

Parts:

• Base assembly from Step 2

• Base Support (#1)

Hardware Qty

• 2 3/4" Bolts (#14) 2

• Washers (#16) 4

• Nuts (#15) 2

Tools:

• Allen wrench (7/32”)

• Wrench/Socket (9/16”) or Open End Wrench

3-1 Carefully tilt the base assembly forward to rest on

the four Tube ends.

3-2 Attach the Base Support (#1) to the Base Bracket

(#2) using the hardware shown in Figure 3. Make

sure that the Base Support feet are pointing away from the base assembly.

Note: Do not tighten hardware at this time.

3-3 Turn the base assembly upright to rest on all four feet.

Parts:

• Base Plate assembly from Step 1

• Base assembly from Step 3

Hardware Qty

• 2 3/4" Bolts (#14) 4

• Washers (#16) 8

• Nuts (#15) 4

Tools:

• Allen wrench (7/32”)

• Wrench/Socket (9/16”) or Open End Wrench

4-1 Place the Base Plate (#6) on the lower Left Tube (#11)

and Right Tube (#12), narrow edge toward the Tube

uprights and the curved edges outside the Tubes. Align

the bolt holes in the Base Plate and Tubes. Install the

hardware in the two bolt holes closer to the uprights.

See Figure 4.

4-2 At the two bolt holes farther from the Tube uprights, insert a 2 3/4" Bolt (#14) through a Washer (#16) and

into each bolt hole.

4-3 Carefully tilt the base assembly forward to rest on the four Tube ends. Install a Washer (#16) and Nut (#15)

onto each of the Bolts from Step 4-2.

Note: Do not tighten hardware at this time.

4-4 Turn the base assembly upright to rest on all four feet.





 







Figure 4













Figure 3

step

Parts:

• Rack base assembly from Step 4

• Right Curl Bar Hook (#3)

• Left Curl Bar Hook (#4)

• Rods (#10)

Hardware Qty

• 2 3/4" Bolts (#14) 4

• 7/8" Bolts (#13) 4

• Washers (#16) 12

• Nuts (#15) 4

Tools:

• Allen wrench (7/32”)

• Wrench/Socket (9/16”) or Open End Wrench

5-1 Install the Right Curl Bar Hook (#3) at the two top, outside

bolt holes on the Right Tube (#12) using the hardware as

shown in Figure 5. Make sure that the Curl Bar Hook curves outward from the Tube, and the hook points

away from the Base Plate. Tighten hardware completely.

5-2 Install the Left Curl Bar Hook (#4) to the Left Tube (#11) as described above.

5-3 Install a Rod (#10) in each of the four large holes on the outsides of the Tube uprights, using the hardware

shown in Figure 5. Tighten hardware completely.





















Figure 5

step

Parts:

• Rack assembly from Step 5

• Cross Member (#7)

• Flex Bag (#9)

Hardware Qty

• 2 3/4" Bolts (#14) 2

• Washers (#16) 4

• Nuts (#15) 2

Tools:

• Allen wrench (7/32”)

• Wrench/Socket (9/16”) or Open End Wrench

6-1 Install the Cross Member (#7) to the outer sides of Tube

uprights above the Rods (#10) using the hardware as

shown in Figure 6. Make sure that the logo faces up-

ward and the hooks point the same direction as the Curl Bar Hooks. Tighten hardware completely.

6-2 Completely tighten all hardware from Steps 2 – 4. Make sure the rack sits evenly on all four feet. You may

need to loosen and retighten the hardware from Steps 2 – 4 and 6-1 to adjust the unit.

6-3 Fasten the Flex Bag (#9) to the Tube uprights between the upper and lower Rods, using the hook-and-loop

straps.













Figure 6

Parts:

• Rack assembly from Step 6

• Color-coded Dots (6 pairs)

7-1 The pairs of colored dots will identify the storage locations for the Bowﬂex Revolution™ accessory

equipment listed in the guide chart below. As you peel each pair of dots from the paper backing, place

one dot on the accessory and the other on its holder on the rack. See Figure 7.

Location Accessory

A Tall Seat Back

B Handgrips & Foot Harnesses

C Leg Press Plate

D Leg Press Seat Back

E Preacher Curl Assembly

F Resistance Packs

Figure 7

















Parts:

• Rack assembly from Step 7

Tools:

• Allen wrench (7/32”)

• Wrench/Socket (9/16”) or Open End Wrench

8-1 Now that you have assembled your Bowﬂex Revolution™ Accessory Rack, it is very important to tighten

all hardware and visually inspect the rack. Make sure that your Bowﬂex Revolution™ Accessory Rack

has been assembled correctly and securely.











To avoid damage to equipment or

injury, store Bowﬂex Revolution™

accessories only in their designated

holders on the rack.

step





























Your Bowﬂex Revolution™ Accessory Rack is now complete. You are ready to store your equipment.

  

 

WARRANTY

LIMITED WARRANTY FOR EXERCISE PRODUCTS

All Bowflex® branded exercise products manufactured by Nautilus, Inc. are warranted to the retail purchaser to be free from defects in materials

and workmanship. Warranty coverage valid to the original purchaser only and proof of purchase will be required. Any product sold or placed in an appli-

cation not recommended by Nautilus will void any warranty coverage set forth by Bowflex® warranty policies and procedures.

TIME PERIOD

This product was designed, warranted, and intended for residential use only.

Residential Environment:

Frame Parts: 90 days

THIS WARRANTY DOES NOT COVER

1. Use in a commercial setting such as health clubs, schools, hotels and hospitals.

2. Damage due to normal wear and tear.

3. Any damage, failure or loss caused by accident, misuse, neglect, abuse, improper assembly, improper maintenance, Acts of God (such as floods or

power surges), or failure to follow instructions or warnings in Owner’s Manual.

4. Use of products in an application not recommended by Nautilus, Inc., or in a manner or environment for which they were not designed.

5. Extended warranties: Nautlus will not be responsible for any extended coverage terms offered by a distributor or service provider.

LIMITATIONS

The foregoing warranties are in lieu of and exclude all other warranties not expressly set forth herein, whether express or implied by operation of law or

otherwise, including, but not limited to, WARRANTY OF MERCHANTABILITY or WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Nautilus,

Inc. shall in no event be liable for incidental or consequential losses, damages or expenses in connection with its exercise products. Nautilus liability

hereunder is expressly limited to the replacement of goods not complying with this warranty or, at Nautilus, Inc.'s sole election, to the repayment of

an amount of the purchase price of the exercise product in question. Some states do not permit the exclusion or limitation of implied warranties

or incidental or consequential damages, so the preceding limitations and exclusions may not apply to you.

PROCEDURES

Warranty service will be performed by the original retailer (seller) or an authorized Bowflex® service provider. The original purchaser must provide

proof of purchase. Service calls, assembly, transportation, and/or delivery expenses are the responsibility of the purchaser: 1-800-NAUTILUS (628-

8458).

1. Nautilus will have the option in its discretion to repair or replace any exercise product(s), which require warranty service, or to apply a limited

credit reimbursement toward another Bowflex® exercise product of equal or greater value.