Breckwell P2000I User Manual To The 0a617947 2291 4627 Bb4a 8b803389e805
User Manual: Breckwell P2000I to the manual
Open the PDF directly: View PDF 
.
Page Count: 1
| Download | |
| Open PDF In Browser | View PDF |
P1000i/P2000i QUICK START GUIDE This Quick Start Guide is not a substitute for reading the Operator’s Manual. To reduce the risk of injury or death, user must read and understand Operator’s Manual before using this product. IMPORTANT Do not connect to a building’s electrical system unless the generator and transfer switch have been verified by a qualified electrician. The connection must isolate the generator power from utility power and must comply with all applicable laws and electrical codes. First Time Starting (Cont.) DANGER Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell. NEVER use inside a home or garage. EVEN IF doors and windows are open. 7. Once the engine is running, slowly move choke lever left to the RUN position. 8. After a 2-3 minute warm up, Push the SMART THROTTLE switch to ON. Troubleshooting PROBLEM - Engine switch is off. - No fuel. - Stale fuel or water in fuel. - Engine oil level is low. - Spark plug faulty, fouled or improperly gapped. - Choke lever is in RUN position. - Engine stored without treating or draining fuel. - Refueled with bad fuel. - Dirty fuel filter. - Turn engine switch to ON. - Fill fuel tank. - Drain entire fuel system and refill with fresh fuel. - Engine is equipped with Low Oil Shutoff. If the engine oil level is low, the unit will not start. Check engine oil level and fill if necessary. - Replace spark plug. - Move choke lever to START position. - Drain fuel and carburetor. Refuel with fresh fuel. - Contact authorized service dealer. Engine hard to start. - Water in fuel. - Weak spark at spark plug. - Drain entire system and refill with fresh fuel. - Contact authorized service dealer. Engine lacks power. - Dirty air filter. - Engine stored without treating or draining fuel, or refueled with bad fuel. - Check air filter element. - Clean or replace as needed. - Drain fuel and carburetor. - Refuel with fresh fuel. AC receptacle does not work. Item plugged in is defective. Overload indicator on (light solid) - Try a different item. - Press reset button. DC receptacle does not work. - Circuit protector engaged. - Item plugged in is defective. - Remove any load from the generator. - Replace the fuse, then depress the DC circuit breaker. - Try a different item. Generator makes a “spark knock” or “pinging” noise. - If knocking or pinging occurs under normal load at a steady engine speed, the problem may be with the fuel being used. - An occasional light “knocking” or “pinging” under heavy load is not a cause for concern. - Switch to a different brand of fuel with a octane rating of 86 or higher. - Contact authorized service dealer. Only use OUTSIDE and far away from windows, doors, and vents. Add engine oil per the Operator’s Manual instructions. Stopping The Unit 1. Disconnect all appliances connected to the generator. Position the Engine Fuel Switch to OFF. Oil fill recommendations using included oil fill bottle: P1000i P2000i 1 oil fill bottles up to #2 mark 2 oil fill bottles up to #2 mark ON OFF Always verify oil level is at upper limit mark on dipstick before operating. 2. 3. 5. Fill the fuel tank per the Operator’s Manual instructions. Position the fuel tank cap vent lever to ON, if equipped. Push the SMART THROTTLE switch to OFF. Position the Engine Fuel Switch to ON. ON OFF 4. 6. Move CHOKE lever right to START position. Lightly pull the engine recoil until resitance is felt. Firmly Pull the engine recoil until the engine starts. 2. Allow the engine to cool. Position the fuel tank cap vent lever to OFF, if equipped. Using The Generator Connect devices to be powered by following the steps below. - Make sure the total rated power from the items you plan to use at the same time are less than the generator continuous (running) watts. Make sure the total surge (starting) power from the items you plan to use at the same time are less than the generator maximum watts. See Operator’s Manual to calculate total amount of power needed. - Start the generator with nothing connected. - Plug in and turn on the first load (perferably the largest load). - Allow the generator output to stabilize (engine runs smoothly and attached device operates properly). - Repeat previous steps for additional loads. IMPORTANT: Never add more load than the generator’s capacity. Please consider surge load when determining total power need. SOLUTION Engine will not start. First Time Starting 1. POSSIBLE CAUSE If problems persist after trying the above solutions, contact your authorized service dealer. The following symptoms may indicate problems that will affect the emissions level on the unit. - Hard starting or stalling - Rough idle - Misfiring or backfiring under load - Afterburning (backfiring) - Black exhaust smoke or high fuel consumption If you encounter any of these symptoms, take the unit to your authorized service dealer for service. Storing The Unit When preparing to store the generator, allow the unit to cool completely. If the unit is going to be stored for more than 4 weeks, drain fuel by releasing the carburator drain screw. Follow complete storage instructions in Operator’s Manual. 9926057 R2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Create Date : 2014:11:21 13:01:52-06:00 Creator : Adobe InDesign CS6 (Windows) Modify Date : 2014:11:24 15:14:49-06:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2014:11:24 15:14:49-06:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:cc0d201f-9c8b-4471-b7ae-ff306725ecd5 Original Document ID : xmp.did:5BF41C92AA71E411B590D82C1C9B218D Document ID : xmp.id:81A4E54AAF71E411B590D82C1C9B218D Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:7EA4E54AAF71E411B590D82C1C9B218D Derived From Document ID : xmp.did:7EA4E54AAF71E411B590D82C1C9B218D Derived From Original Document ID: xmp.did:5BF41C92AA71E411B590D82C1C9B218D Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:11:21 13:01:52-06:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 1EXIF Metadata provided by EXIF.tools