Briggs And Stratton 287700 Users Manual 683v28,31
287700 to the manual 67e1fae3-7fe9-bb14-e1b4-e9292cc4cfa6
2015-02-04
: Briggs-And-Stratton Briggs-And-Stratton-287700-Users-Manual-363513 briggs-and-stratton-287700-users-manual-363513 briggs-and-stratton pdf
Open the PDF directly: View PDF .
Page Count: 12
Download | |
Open PDF In Browser | View PDF |
Before starting this engine, read and understand this Operator/Owner Manual. Failure to follow instructions in this manual could result in serious injury or death. 28N700, 287700, 28P700, 28Q700, 28S700, 28U700, 310700, 311700, 312700, 313700 Model Type Code For future reference, write your engine Model/Type/Code here. For future reference, write your engine Date of Purchase here. Table of Contents Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 In the Interest of Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Service, Storage & Specifications . . . . . . . . . . . . . . . . . . 9 Oil & Fuel Recommendations . . . . . . . . . . . . . . . . . . . . . . 3 Emission System Warranty . . . . . . . . . . . . . . . . . . . . . . . 10 Starting & Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About Engine Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Engine Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Briggs & Stratton Corporation Milwaukee, Wisconsin 53201 www.briggsandstratton.com Copyright 1998 by Briggs & Stratton Corporation FORM NO. 273683-7/98 PRINTED IN U.S.A. Maintenance, replacement or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual. However, to obtain no charge repairs under the terms and provisions of the Briggs & Stratton warranty statement, any service or emission control part repair or replacement must be performed by a factory authorized dealer. In the Interest of Safety This safety alert symbol indicates that this message You are not ready to operate this engine if you involves personal safety. Words danger, warning have not read and understood the following and caution indicate degree of hazard. Death, safety items. Read this entire owner’s manual and personal injury and/or property damage may occur the operating instructions of the equipment this engine powers. unless instructions are followed carefully. The Briggs & Stratton engine you bought with your equipment is made of the finest material in a state-of-the-art manufacturing facility. Please understand that Briggs & Stratton sells engines to original equipment manufacturers. It also sells to others in the distribution chain who may sell to the ultimate consumer, an equipment manufacturer, another distributor or a dealer. As a result, Briggs & Stratton does not necessarily know the application on which the engine will be placed. For that reason, you should carefully read and understand the operating instructions of the equipment on which your engine is placed before you operate it. You should also understand that there are equipment applications for which Briggs & Stratton does not approve the use of its engines. Briggs & Stratton engines are not to be used on vehicles with less than 4 wheels. They include motor bikes, aircraft products and All Terrain Vehicles. Moreover, Briggs & Stratton does not approve of its engines being used in competitive events. F0R THAT REASON, BRIGGS & STRATTON ENGINES ARE NOT AUTHORIZED FOR ANY OF THESE APPLICATIONS. Failure to follow this warning could result in death, serious injury (including paralysis) or property damage. DO NOT check for spark with spark plug removed. (Use an approved tester.) DO NOT crank engine with spark plug removed. (If engine is flooded, place throttle in FAST and crank until engine starts.) DO NOT strike flywheel with a hammer or hard object as this may cause flywheel to shatter in operation. (To remove flywheel, use Briggs & Stratton approved tools only.) DO NOT operate engine without a muffler. (Inspect periodically and replace if worn or leaking. If engine is equipped with muffler deflector, inspect periodically and replace if necessary. Replacement parts must be same as on original equipment.) DO NOT operate engine with an accumulation of grass, leaves or other combustible material in muffler area. DO NOT use this engine on any forest covered, brush covered, or grass covered unimproved land unless a spark arrester is installed on muffler. The spark arrester must be maintained in working order by the owner and/or operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. DO NOT touch hot muffler, cylinder, or fins which can cause burns. DO NOT start engine with air cleaner or air cleaner cover removed (or cover over carburetor air intake, if Sno/Gard engine). DO NOT attempt to start engine with cutting blade loose or removed. (Blade must be tight, otherwise a kickback may occur.) DO NOT run engine in an enclosed area. (Exhaust gases contain carbon monoxide, an odorless and deadly poison.) DO NOT remove fuel tank cap nor fill fuel tank while engine is hot or running. DO NOT refuel indoors or in an unventilated area. (Allow engine to cool 2 minutes before refueling.) DO NOT place hands or feet near moving or rotating parts. DO NOT store, spill, or use gasoline near an open flame, nor near an appliance like a stove, furnace, or water heater that uses a pilot light or can create a spark. DO NOT refuel indoors or in an unventilated area. DO NOT operate or tip engine/equipment at such a severe angle that causes gasoline spillage. DO NOT operate engine if gasoline is spilled or when smell of gasoline is present or other explosive conditions exist. (Move equipment away from spill and avoid any ignition until gasoline has evaporated.) DO NOT transport engine with fuel in tank or fuel shut-off valve open. DO NOT choke carburetor to stop engine, especially in an enclosed vehicle. (Whenever possible, gradually reduce engine speed before stopping.) DO NOT tamper with governor springs, links or other parts to increase engine speed. (Run engine at speed set for equipment manufacturer.) leaks. Replace if necessary. ✔ PULL starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury. ✔ Use only Genuine Briggs & Stratton Parts or their equivalent. The use of replacement parts which are ✔ PREVENT ACCIDENTAL STARTING by removing spark not of equivalent quality may damage the engine. plug wire from spark plug when servicing engine or equipment. Disconnect negative wire from battery terminal if equipped with electric starting system. ✔ REMOVE blower housing periodically and clean engine. The engine exhaust from this product Keep cylinder fins and governor parts free of dirt, grass contains chemicals known to the State and other debris which can affect engine speed. of California to cause cancer, birth ✔ USE fresh gasoline. Stale fuel can gum carburetor and defects, or other reproductive harm. cause leakage. ✔ CHECK fuel lines and fittings frequently for cracks or International Safety Alert - Read Fuel On Off Stop Fuel Choke Owner’s Manual Shutoff Symbols In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 2 Oil & Fuel Recommendations Oil Fuel This engine is shipped from Briggs & Stratton without oil. Before starting engine, check oil level as shown below. Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane. Do not mix oil with gasoline. Fresh fuel prevents gum from forming in fuel system or on essential carburetor parts. Purchase fuel in quantity that can be used within 30 days. In countries other than the U.S.A., leaded gasoline may be used if commercially available and unleaded is unavailable. We recommend the use of Briggs & Stratton Gasoline Additive. (See your Authorized Briggs & Stratton Service Dealer for Part No. 5041 or the single-use pouch.) See storage instructions, on page 9. Note: Some fuels, called oxygenated or reformulated gasolines, are gasolines blended with alcohols or ethers. Excessive amounts of these blends can damage the fuel system or cause performance problems. Do not use gasoline which contains Methanol. If any undesirable operating symptoms occur, use gasoline with a lower percentage of alcohol or ether. Do not over-fill fuel tank. Allow space for fuel expansion. Change and add oil according to chart below. Do not over-fill. Use a high quality detergent oil classified “For Service SF, SG, SH,” such as Briggs & Stratton “warranty certified” SAE 30 oil, Part No. 100005. Use no special additives with recommended oils. Do not mix oil with gasoline. SAE Viscosity Grades ** * °F °C -20 -30 20 0 -20 -10 32 0 40 60 10 80 20 100 30 40 STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE * Air cooled engines run hotter than automotive engines. The use of multi-viscosity oil such as (10W-30, etc.) in ambient temperatures above 40° F (4° C) will result in higher than normal oil consumption. If multi-viscosity oil is used, check the oil level more frequently to prevent any possible engine damage due to lack of lubrication. ** Use of SAE 30 oil below 40° F (4° C) will result in hard starting and possible engine damage due to inadequate lubrication. Check oil level before starting engine. Add oil as shown below. Oil capacity is about 1-1/2 quarts (48 ounces or 1.4 liter). Oil capacity is about 1-1/2 quarts (48 ounces or 1.4 liters) if engine is not equipped with oil filter. Oil capacity is about 1-3/4 quarts (56 ounces or 1.7 liters) if engine is equipped with oil filter. After filling with or changing oil, start and run engine at idle for 30 seconds. Shut engine off. Wait 30 seconds and check oil level. Add oil, if required, to bring level to Full mark on dipstick. 4 3 2 1. 2. 3. 4. 5. 6. Oil drain Oil fill/Dipstick Rotating screen Blower housing Muffler 12V electric starter 5 6 1 12 7 Place engine level. Remove dipstick. Tighten dipstick. Clean around oil fill. Wipe with clean cloth. Remove & check. 11 7. Air cleaner 8. In-line fuel filter, if equipped 9. Carburetor 10. Oil filter, if equipped 11. Spark plug wire 12. Engine Model Type xxxxxx xxxx xx Oil level should If oil is required, add Tighten dipstick bebe at FULL mark. slowly. Recheck level. fore starting engine. 9 8 10 Code xxxxxxxx In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 3 Starting & Stopping Choke operation/engine warm-up This engine is a low emissions engine which operates differently from previously built engines. It is designed for maximum performance and life if operated with the choke fully open (in RUN) and throttle fully open (in FAST). To open the choke fully requires an engine warm-up period of several seconds to several minutes, depending on the temperature. After starting engine, first open the choke (toward RUN) until the engine just begins to run smoothly. Then open the choke in small steps, allowing the engine to accept small changes in speed and load, until the choke is fully open (in RUN). During engine warm-up, the equipment can be operated. To obtain best starting results Store and fuel lawn mower in level position. Start lawn mower on hard surface or over previously cut grass. Start engine Always keep hands and feet clear of mower blade or other rotating machinery. Electric starter Turn key to START or press button. Repeat if necessary with throttle control in FAST position. Operate engine in FAST position. Note: If equipment manufacturer has supplied battery, charge it before trying to start engine, as equipment manufacturer recommends. Use short starting cycles (15 secs. per min.) to prolong starter life. Extended cranking can damage starter motor. PRESS BUTTON Do not use a pressurized starting fluid. Starting fluid is flammable. Severe engine damage or fire may occur. Periodically remove grass build-up under mower deck. Remove spark plug wire before removing grass. When tipping lawn mower to remove grass, keep spark plug side of engine up. Typical electric starter Rewind starter (auxiliary), if equipped If your engine is equipped with an auxiliary rewind starter, grasp rope handle as illustrated and pull slowly until resistance is felt. Then pull cord rapidly to overcome compression, prevent kickback and start engine. Repeat if necessary with choke off and throttle control in FAST position. Operate engine Rewind starter in FAST position. A warm engine requires less choking than a cold engine. Starting in cold weather: Use the correct oil for the starting temperature expected. De-clutch all possible external loads. Set speed control at part throttle position. A warm battery has more starting capacity than a cold battery. Do not use gasoline left over from summer. Use fresh winter grade gasoline which has higher volatility to improve starting. Stop engine Do not move choke control to CHOKE position to stop engine. Backfire or engine damage may occur. Keep throttle control in FAST position. Turn key to OFF. Always remove key from switch, if equipped, when equipment is not in use or left unattended. Before starting engine Move choke control to CHOKE or START position. If equipment has separate choke and throttle controls, move throttle control to FAST position. Note: Choke must fully close. If engine does not start, see control adjustments on page 5. Typical stop controls Typical choke and throttle controls When engine is transported, close fuel shut-off valve (if equipped) to prevent fuel leakage. Open fuel shut-off valve, if equipped. 1/4 TURN 1/4 TURN Typical fuel shut-off Typical fuel shut-off In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 4 Adjustments Control adjustments Carburetor adjustments The manufacturer of the equipment on which this engine is installed specifies top speed at which the engine will be operated. DO NOT EXCEED this speed. WIRE To prevent accidental starting, remove and ground spark plug wire and disconnect battery at negative terminal, if equipped, when adjusting controls. Differences in fuel, temperature, altitude or load may require minor carburetor adjustment. Air cleaner and air cleaner cover must be assembled to carburetor before starting engine. Remote choke control: Move choke control to CHOKE or START position. Choke valve should be closed. To assure choke valve is closed, loosen casing clamp screw and pull casing, wire and choke lever in direction of arrow to end of travel. With choke control in CHOKE or START position, tighten casing clamp screw. The carburetor on this engine is low emission. It is equipped with an idle mixture valve with a limiter (see inset), which allows some adjustment, and an idle speed adjustment screw. Adjustments Start engine and warm up approximately 5 minutes before adjusting. With engine running, place throttle control in SLOW position. Rotate carburetor throttle lever against the idle speed screw and hold it. Turn idle speed screw to obtain 1750 rpm. Rotate idle mixture valve full travel clockwise and then counterclockwise. Finally, position idle mixture valve in middle of travel. Check idle speed and re-adjust to 1750 rpm, if necessary. Move throttle control to FAST position. Engine should accelerate smoothly. If it does not, adjust idle mixture valve counterclockwise 1/8 turn. CASING CLAMP SCREW Choke control adjustment CARBURETOR THROTTLE LEVER To adjust throttle control: With throttle control in FAST position, hole in governor control lever (located just behind governor control plate) must align with hole in governor control plate, as illustrated below. If it does not, loosen casing clamp screw and then move governor control rack until it does. Tighten casing clamp screw. IDLE MIXTURE VALVE WITH LIMITER IDLE SPEED SCREW Check stop switch Move throttle control to STOP position, if equipped. Governor control lever must make good contact with stop switch. Check operation of controls. Readjust if necessary. HOLE IN GOVERNOR CONTROL PLATE STOP SWITCH GOVERNOR CONTROL RACK GOVERNOR CONTROL LEVER Carburetor adjustments CASING CLAMP SCREW Throttle control adjustment In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 5 See Maintenance Schedule, page 8. Follow the hourly or calendar intervals, whichever occur first. Maintenance Note that more frequent service is required when operating in adverse conditions. Air cleaner WIRE To prevent accidental starting, remove and ground spark plug wire and disconnect battery at negative terminal, if equipped, when adjusting controls. COVER KNOB Oil COVER CARTRIDGE KNOB Check oil level regularly. Be sure correct oil level is maintained. Check every 8 hours or daily, before starting engine. See check oil level on page 3. CARTRIDGE & PRE-CLEANER 5053 Change oil (Follow Maintenance Schedule.) Change oil after first 5 hours of operation. Change oil while engine is warm. Remove drain plug and drain oil. Replace and tighten drain plug. Remove dipstick and refill with new oil of recommended grade (see chart, page 3). Start and run engine at idle for 30 seconds. Stop engine. Wait 30 seconds and re-check oil level. If required, add oil to bring level to FULL mark on dipstick. STUD BASE Dual element air cleaner Note: Depending on engine Type Number, this engine may not be equipped with a pre-cleaner. PIPE 7/16” 1. Remove cover knob and cover. 2. Remove cartridge knob. Carefully lift pre-cleaner and cartridge from base over stud. HEX 5/16” Typical drain plugs OIL DRAIN PLUG 3. Clean base carefully to prevent debris from entering carburetor. TO REMOVE Oil drain To service pre-cleaner, wash in liquid detergent and water. Squeeze dry in a clean cloth. Saturate in engine oil. Squeeze in clean, absorbent cloth to remove all EXCESS oil. Replace if very dirty or damaged. Oil fill To service cartridge, clean by tapping gently on a flat surface. Do not oil cartridge. Replace if very dirty or damaged. Change oil filter, if equipped (Follow Maintenance Schedule.) Replace oil filter after every 100 hours of operation or every season, whichever occurs first. Before installing new filter, lightly oil filter gasket with fresh, clean engine oil. Screw filter on by hand until gasket contacts oil filter adapter. Tighten 1/2 to 3/4 turn more. Start and run engine at idle to check for oil leaks. Recheck oil level and add oil if required. PRE-CLEANER 272403 Pre-cleaner CARTRIDGE 496894 Cartridge Note: Do not use petroleum solvents, e.g., kerosene, which will cause the cartridge to deteriorate. Do not use pressurized air to clean cartridge. Pressurized air can damage the cartridge. OIL FILTER P/N SEE PAGE 8 4. Reassemble pre-cleaner on cartridge and place assembly over stud on base. Tighten cartridge knob. Oil filter 5. Replace cover and tighten cover knob securely. In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 6 See Maintenance Schedule, page 8. Follow the hourly or calendar intervals, whichever occur first. Maintenance Note that more frequent service is required when operating in adverse conditions. Grass, chaff or debris may clog the air cooling system, especially after prolonged operation cutting tall, dry grass. Remove blower housing and clean area shown to prevent overheating and engine damage. Clean more often if necessary. Keep engine and parts clean. Do not clean with a forceful spray of water because water could contaminate fuel system. With a brush or cloth, CLEAN CLEAN remove grass, chaff or debris from finger guard or rotating screen daily (more often if needed) to prevent engine damage caused by overheating. Finger guard Rotating screen CLEAN OUT CHAFF AND DEBRIS To assure smooth operation, keep governor linkage, springs and controls free of debris. Air cooling system Replace spark plug. Do not blast clean. Clean by scraping or wire brushing and washing with a commercial solvent. CLEAN Linkage, springs & controls Use only Briggs & Stratton Spark Tester, Part No. 19368, to check for spark. If engine muffler is equipped with spark arrester screen, remove for cleaning and inspection. Replace if damaged or plugged. See an Authorized Briggs & Stratton Service Dealer for correct replacement. ARRESTER Drain fuel tank or close fuel shut-off valve before replacing fuel filter. CLEAN Muffler and spark arrester See any Authorized Briggs & Stratton Service Dealer. Insist on Genuine Briggs & Stratton parts! Non-original parts may not perform as well and may void your warranty. RESISTOR PART NO. 491055 Spark plug Note: In some areas, local law requires using resistor spark plug to suppress ignition signals. If this engine was originally equipped with resistor spark plug, use same type for replacement. Replace in-line fuel filter. FILTER See any Authorized Briggs & Stratton Dealer for correct replacement. CLEAN Daily or more often, before running engine, clean muffler area to remove all grass and combustible debris. .030” (0.76 mm) WIRE GAGE PART NO. 394358 (WITH FUEL PUMP) In-line fuel filter Fill in both sides, clip and return to: Briggs & Stratton Corporation P.O. Box 1144 Milwaukee, WI 53201-1144 U.S.A. To obtain a complete Parts List of Genuine Briggs & Stratton Parts for your engine, fill in both sides of this order form carefully. We cannot fill your order without the correct Engine Model/Type/Code. (Please allow 3 to 4 weeks for delivery.) Your Engine Model 273683 Type P/N 298090 OR 5018 (WITHOUT FUEL PUMP) Code In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 7 Maintenance Schedule 273683 Follow the hourly or calendar intervals, whichever occur first. More frequent service is required when operating in adverse conditions noted below. Every 8 Hours or Daily Maintenance Operation 25 Hours or Every Season 50 Hours or Every Season 100 Hours or Every Season Yearly Check oil level Note 1 Change oil ♦ Replace oil filter, if equipped Note 2 Note 2 Service air cleaner pre-cleaner, if equipped Service air cleaner cartridge, if not equipped with pre-cleaner Service air cleaner cartridge, if equipped with pre-cleaner Inspect spark arrester, if equipped Note 2 Note 2 Clean cooling system Replace spark plug and fuel filter, if equipped Check valve clearance ♦ Change oil after first 5 hours, then after every 50 hours or every season. Note 1: Change oil every 25 hours when operating under heavy load or in high temperatures. Clean more often under dusty conditions or when airborne debris is present. Note 2: Replace air cleaner parts, if very dirty. Briggs & Stratton Part Numbers of some Genuine Briggs & Stratton Parts: Briggs & Stratton Part No. Part Air cleaner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . 496894 Air cleaner pre-cleaner . . . . . . . . . . . . . . . . . . . . . . . . 272403 Air cleaner cartridge & pre-cleaner . . . . . . . . . . . . . . . . 5053 Resistor spark plug . . . . . . . . . . . . . . . . . . . . . . . . . . . 491055 Spark plug wrench . . . . . . . . . . . . . . . . . . . . . 89838 or 5023 Spark tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19368 Payment Method: Briggs & Stratton Part Numbers of some Genuine Briggs & Stratton Parts: Part Briggs & Stratton Part No. Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100005 or 100028 Oil filter (3-1/2 in. long) . . . . . . . . . . . . . . . . . . . . . . . . 491056 Oil filter (2-1/4 in. long) . . . . . . . . . . . . . . . . . . . . . . . . 492932 Fuel filter (with fuel pump) . . . . . . . . . . . . . . . . . . . . . 394358 Fuel filter (without fuel pump) . . . . . . . . . . . . . . . . . . 298090 Gas additive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5041 Fill in both sides of this order form carefully Check or money order enclosed payable to Briggs & Stratton Corporation in the amount of $________ Please charge my MasterCard (U.S. Dollars, please) Only Genuine Briggs & Stratton Parts have the Briggs & Stratton logo! VISA __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ CREDIT CARD NUMBER SIGNATURE (REQUIRED FOR CREDIT CARD ORDERS Parts List Shipping & Handling **Add State Sales Tax Total EXPIRATION DATE $2.00 $1.50 Add sales tax if you live in any of the following states: Look for Briggs & Stratton logo stamped on part and/or package! In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 8 Service, Storage & Specifications For service See an Authorized Briggs & Stratton Service Dealer. Each one carries a stock of Genuine Briggs & Stratton Parts and is equipped with special service tools. Trained mechanics assure expert repair service on all Briggs & Stratton engines. Only dealers advertising as “Authorized Briggs & Stratton” are required to meet Briggs & Stratton standards. When you purchase equipment powered by a Briggs & Stratton engine, you are assured of highly skilled, reliable service at more than 30,000 Authorized Service Dealers worldwide, including more than 2,700 Master Service Technicians. Look for these signs wherever Briggs & Stratton service is offered. Storage instructions Engines stored over 30 days need to be protected or drained of fuel to prevent gum from forming in fuel system or on essential carburetor parts. 1. For engine protection, we recommend use of Briggs & Stratton Gasoline Additive, Part No. 5041, available from an Authorized Briggs & Stratton Service Dealer. Mix Additive with fuel in fuel tank or storage container. Run engine for a short time to circulate Additive through carburetor. Engine and fuel can be P/N 5041 stored up to 24 months. Your Service Dealer has single-use pouches of Gasoline Additive available. You may locate your nearest Authorized Briggs & Stratton Service Dealer in the “Yellow Pages” directory under “Engines, Gasoline” or “Gasoline Engines,” or “Lawn Mowers” or similar category. Or log on to our dealer locator map on our web site www.briggsandstratton.com Note: Walking fingers logo and “Yellow Pages” are registered trademarks in various jurisdictions. The illustrated shop manual shown here includes “Theories of Operation,” common specifications and detailed information covering adjustment, tune-up and repair of Briggs & Stratton single cylinder, overhead valve, 4 cycle engines. It is available from an Authorized Briggs & Stratton Service Dealer or you can order it from the factory. Write: Briggs & Stratton Corporation Part No. 272147 Attn: Service Division P. O. Box 1144 Milwaukee, WI 53201 Note: If engine is operating on oxygenated or reformulated gasoline (gasoline blended with an alcohol or an ether), remove all fuel from tank and run engine until it stops from lack of fuel. If engine is stored with gasoline in fuel tank, we recommend the use of Gasoline additive, Part No. 5041. 2. While engine is still warm, drain oil from crankcase (see page 6). Refill with fresh oil of recommended grade (see chart page 3). 3. Remove spark plug and pour about 1 oz (30 ml) of engine oil into cylinder. Replace spark plug and crank slowly to distribute oil. 4. Clean dirt and chaff from cylinder, cylinder head fins, blower housing, rotating screen and muffler area (see page 7). 5. Store in a clean and dry area, but NOT near a stove, furnace or water heater which uses a pilot light or any device that can create a spark. General information Tune-up specifications This is a single cylinder, over-head valve (OHV), air-cooled engine. Armature air gap is .010-.014 in. (.25-.36 mm) On mobile equipment, this engine will operate satisfactorily at any angle at which operator and equipment can function safely. Valve clearance is: Intake* . . . . . . . . . . . . . . . . . . . . . . .003-.005 in. (.08-.13 mm) Exhaust* . . . . . . . . . . . . . . . . . . . . .005-.007 in. (.13-.18 mm) Spark plug gap is .030 in. (.76 mm) Model Series 28E700, 28N700, 287700, 28P700, 28Q700, 28S700, 28U700 Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7/16 in. (87.31 mm) Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1/16 in. (77.78 mm) Displacement . . . . . . . . . . . . . . . . . . . 28.42cu. in. (465.7 cc) Torque (Max.) . . . . . . . . . . . . . . . . . . 22.9 ft. lbs. @ 2700 rpm Model Series 310700, 311700, 312700, 313700 Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9/16 in. (90.60 mm) Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1/16 in. (77.78 mm) Displacement . . . . . . . . . . . . . . . . . . . 30.59 cu. in. (501.2 cc) * with valve springs installed and piston 1/4 in. (6mm) past top dead center. Note: For practical operation, the horsepower loading should not exceed 85% of rated horsepower. Engine power will decrease 3-1/2% for each 1,000 feet (300 meters) above sea level and 1% for each 10° F (5.6° C) above 77° F (25° C). In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 9 273683 Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.S. EPA) Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations) In the interest of the environment, B&S engines that meet strict emisTO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 sion requirements are labeled, “This engine conforms to 1995 - 1998 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND California emission regulations for ULGE engines and U.S. EPA TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES Phase I regulations for small non-road engines.” WHICH ARE PURCHASED AND USED ELSEWHERE IN THE UNITED STATES. EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE California and United States Emission Control Defects Warranty Statement CARB, U.S. EPA and B&S are pleased to explain the Emission Conthere has been no abuse, neglect or improper maintenance of your trol System Warranty on your 1996 and later utility or lawn and garULGE engine. den equipment (ULGE) engine. In California, new ULGE engines Your emission control system includes parts such as the carburetor, produced on or after August 1, 1995 must be designed, built and air cleaner, ignition system, muffler and catalytic converter. Also inequipped to meet the State’s stringent anti-smog standards. Elsecluded may be connectors and other emission related assemblies. where in the United States, new non-road, spark-ignition engines Where a warrantable condition exists, B&S will repair your ULGE encertified for model year 1997 and later, must meet similar standards gine at no cost to you including diagnosis, parts and labor. set forth by the U.S. EPA. B&S must warrant the emission control system on your engine for the periods of time listed below, provided Briggs & Stratton Emission Control Defects Warranty Coverage ULGE engines are warranted relative to emission control parts deany covered part on your engine is defective, the part will be repaired fects for a period of two years, subject to provisions set forth below. If or replaced by B&S. Owner’s Warranty Responsibilities As the ULGE engine owner, you are responsible for the performance You are responsible for presenting your ULGE engine to an Authoof the required maintenance listed in your Operator/Owner Manual. rized B&S Service Dealer as soon as a problem exists. The undisB&S recommends that you retain all your receipts covering mainteputed warranty repairs should be completed in a reasonable amount nance on your ULGE engine, but B&S cannot deny warranty solely of time, not to exceed 30 days. for the lack of receipts or for your failure to ensure the performance of If you have any questions regarding your warranty rights and reall scheduled maintenance. sponsibilities, you should contact a B&S Service Representative at 1-414-259-5262. As the ULGE engine owner, you should however be aware that B&S may deny you warranty coverage if your ULGE engine or a part has The emission warranty is a defects warranty. Defects are judged on failed due to abuse, neglect, improper maintenance or unapproved normal engine performance. The warranty is not related to an in-use modifications. emission test. Briggs & Stratton Emission Control Defects Warranty Provisions The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated engines found in the Operator/Owner Manual. 3. No Charge 1. Warranted Parts Repair or replacement of any Warranted Part will be performed Coverage under this warranty extends only to the parts listed beat no charge to the owner, including diagnostic labor which leads low (the emission control systems parts) to the extent these to the determination that a Warranted Part is defective, if the parts were present on the engine purchased. diagnostic work is performed at an Authorized B&S Service a. Fuel Metering System Dealer. For emissions warranty service contact your nearest Au• Cold start enrichment system (soft choke) thorized B&S Service Dealer as listed in the “Yellow Pages” under “Engines, Gasoline,” “Gasoline Engines,” “Lawn Mowers,” • Carburetor and internal parts or similar category. • Fuel Pump 4. Claims and Coverage Exclusions b. Air Induction System Warranty claims shall be filed in accordance with the provisions • Air cleaner of the B&S Engine Warranty Policy. Warranty coverage shall be • Intake manifold excluded for failures of Warranted Parts which are not original B&S parts or because of abuse, neglect or improper maintec. Ignition System nance as set forth in the B&S Engine Warranty Policy. B&S is not • Spark plug(s) liable to cover failures of Warranted Parts caused by the use of • Magneto ignition system add-on, non-original, or modified parts. 5. Maintenance d. Catalyst System Any Warranted Part which is not scheduled for replacement as • Catalytic converter required maintenance or which is scheduled only for regular in• Exhaust manifold spection to the effect of “repair or replace as necessary” shall be • Air injection system or pulse valve warranted as to defects for the warranty period. Any Warranted Part which is scheduled for replacement as required maintee. Miscellaneous Items Used in Above Systems nance shall be warranted as to defects only for the period of time • Vacuum, temperature, position, time sensitive valves up to the first scheduled replacement for that part. Any replaceand switches ment part that is equivalent in performance and durability may • Connectors and assemblies be used in the performance of any maintenance or repairs. The owner is responsible for the performance of all required mainte2. Length of Coverage nance, as defined in the B&S Operator/Owner Manual. B&S warrants to the initial owner and each subsequent purchaser 6. Consequential Coverage that the Warranted Parts shall be free from defects in materials and workmanship which caused the failure of the Warranted Coverage hereunder shall extend to the failure of any engine Parts for a period of two years from the date the engine is delivcomponents caused by the failure of any Warranted Part still unered to a retail purchaser. der warranty. In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 10 About your engine warranty: (see back cover for statement of LIMITED WARRANTY). Briggs & Stratton welcomes warranty repair and apologizes to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty would not apply if engine damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, warranty is void if the serial number of the engine has been removed or the engine has been altered or modified. 4. Parts which are scored or broken because an engine was operated with insufficient or contaminated lubricating oil, or an incorrect grade of lubricating oil (check oil level daily or after every 8 hours of operation. Refill when necessary and change at recommended intervals.) Read “Owner’s Manual.” 5. Repair or adjustment of associated parts or assemblies such as clutches, transmissions, remote controls, etc., which are not manufactured by Briggs & Stratton. 6. Damage or wear to parts caused by dirt, which entered the engine because of improper air cleaner maintenance, re-assembly, or use of a non-original air cleaner element or cartridge. (At recommended intervals, clean and re-oil the Oil-Foam element or the foam pre-cleaner, and replace the cartridge.) Read “Owner’s Manual.” 7. Parts damaged by overspeeding, or overheating caused by grass, debris, or dirt, which plugs or clogs the cooling fins, or flywheel area, or damage caused by operating the engine in a confined area without sufficient ventilation. (Clean fins on the cylinder, cylinder head and flywheel at recommended intervals.) Read “Owner’s Manual.” 8. Engine or equipment parts broken by excessive vibration caused by a loose engine mounting, loose cutter blades, unbalanced blades or loose or unbalanced impellers, improper attachment of equipment to engine crankshaft, overspeeding or other abuse in operation. 9. A bent or broken crankshaft, caused by striking a solid object with the cutter blade of a rotary lawn mower, or excessive v-belt tightness. 10. Routine tune-up or adjustment of the engine. 11. Engine or engine component failure, i.e., combustion chamber, valves, valve seats, valve guides, or burned starter motor windings, caused by the use of alternate fuels such as, liquified petroleum, natural gas, altered gasolines, etc. If a customer differs with the decision of the Service Dealer, an investigation will be made to determine whether the warranty applies. Ask the Service Dealer to submit all supporting facts to his Distributor or the Factory for review. If the Distributor or the Factory decides that the claim is justified, the customer will be fully reimbursed for those items that are defective. To avoid misunderstanding which might occur between the customer and the Dealer, listed below are some of the causes of engine failure that the warranty does not cover. Improper maintenance: The life of an engine depends upon the conditions under which it operates, and the care it receives. Some applications, such as tillers, pumps and rotary mowers, are very often used in dusty or dirty conditions, which can cause what appears to be premature wear. Such wear, when caused by dirt, dust, spark plug cleaning grit, or other abrasive material that has entered the engine because of improper maintenance, is not covered by warranty. This warranty covers engine related defective material and/or workmanship only, and not replacement or refund of the equipment to which the engine may be mounted. Nor does the warranty extend to repairs required because of: 1. PROBLEMS CAUSED BY PARTS THAT ARE NOT ORIGINAL BRIGGS & STRATTON PARTS. 2. Equipment controls or installations that prevent starting, cause unsatisfactory engine performance, or shorten engine life. (Contact equipment manufacturer.) Warranty is available only through service dealers which have been authorized by Briggs & Stratton Corporation. Your nearest Authorized Service Dealer is listed in the “Yellow Pages” of your telephone directory under “Engines, Gasoline” or “Gasoline Engines,” “Lawn Mowers,” or similar category. 3. Leaking carburetors, clogged fuel pipes, sticking valves, or other damage, caused by using contaminated or stale fuel. (Use clean, fresh, lead-free gasoline and Briggs & Stratton gasoline stabilizer, Part No. 5041.) Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design D-247,177 (Other Patents Pending) 4,522,080 DES. 309,458 5,642,701 5,320,795 5,197,425 5,105,331 5,009,208 4,875,448 5,197,422 5,086,890 4,996,956 4,819,593 4,520,288 DES. 309,457 5,606,948 5,271,363 DES. 308,872 5,548,955 5,269,713 5,191,864 5,070,829 4,995,357 4,719,682 4,453,507 5,188,069 5,058,544 4,977,879 4,694,792 4,430,984 DES. 308,871 5,546,901 5,265,700 4,971,219 4,633,556 4,355,253 5,503,125 5,243,878 5,186,142 5,040,644 5,497,679 5,235,943 5,138,996 5,040,503 4,895,119 4,630,498 4,270,509 In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 11 BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY effective July 1, 1998 Replaces all undated Warranties and all Warranties dated before July 1, 1998 LIMITED WARRANTY “Briggs & Stratton Corporation will repair or replace, free of charge, any part, or parts of the engine that are defective in material or workmanship or both. Transportation charges on parts submitted for repair or replacement under this Warranty must be borne by purchaser. This warranty is effective for the time periods and subject to the conditions provided for in this policy. For warranty service contact your nearest Authorized Service Dealer as listed in the ‘Yellow Pages’ under ‘Engines, Gasoline,’ ‘Gasoline Engines,’ ‘Lawn Mowers’ or similar category. THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.” Briggs & Stratton Corporation F. P. Stratton, Jr. Chairman and Chief Executive Officer WARRANTY PERIOD WITHIN U.S.A. AND CANADA ENGINES All Vanguard engines. CONSUMER USE* COMMERCIAL USE* OUTSIDE U.S.A. AND CANADA CONSUMER USE* COMMERCIAL USE* 2 year – engine } / Lifetime** – Magnetron ignition All Diamond Plus, Industrial Plus, I/C engines and sleeve bore Intek series. 2 year 1 year 2 year } 1 year Quantum and Diamond Power. 2 year 90 days {2 year { } 90 days All standard engines and Kool Bore Intek series installed on lawn mowers, riders, edgers, chippers, shredders, tillers, fun carts, and all Sno/Gard engines. 2 year 90 days 1 year 90 days All other standard engines and Classic series. 1 year 90 days 1 year 90 days * For purposes of this warranty policy, “consumer use” means personal residential household use by the original retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty. Engines used in competitive racing or on commercial or rental tracks are not warrantied. ** Lifetime limited warranty of the Magnetron ignition covers parts and labor for the first five (5) years from the date of purchase; thereafter only parts. “Lifetime” means lifetime of the engine in the hands of the original purchaser. { One (1) year in Australia, New Zealand, Middle East and Africa. } One (1) year in India. NO WARRANTY REGISTRATION CARD IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON ENGINES. YOU MUST SAVE THE PURCHASE RECEIPT. A PROOF OF PURCHASE DATE WILL BE REQUIRED TO OBTAIN WARRANTY. In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 12 Create Date : 1999:05:04 10:54:06 Producer : Acrobat Distiller 3.01 for Windows Author : tara Creator : Interleaf, Inc. Title : 683v28,31EXIF Metadata provided by EXIF.tools