Brivo Systems A206 Access Control System User Manual Brivo ACS Installation Guide 7 27 01
Brivo Systems, Inc. Access Control System Brivo ACS Installation Guide 7 27 01
Exhibit D Users Manual per 2 1033 c3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 164038 |
| Application ID | imBeaydOQrtvyWU/6bxzwQ== |
| Document Description | Exhibit D Users Manual per 2 1033 c3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 196.1kB (2451285 bits) |
| Date Submitted | 2001-08-10 00:00:00 |
| Date Available | 2001-10-12 00:00:00 |
| Creation Date | 2001-08-09 16:19:43 |
| Producing Software | Acrobat PDFWriter 4.05 for Windows NT |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | Brivo ACS Installation Guide 7.27.01.doc |
| Document Creator | Brivo ACS Installation Guide 7.27.01.doc - Microsoft Word |
| Document Author: | ETemplet |
Brivo ACS Installation Manual Version 1.01 DRAFT Brivo ACS Installation Guide August 2001 NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation or when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, wich can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antennae. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Information in this document is subject to change without notice and does not represent a commitment on the part of Brivo Systems, Inc.. For the most up-to-date information, visit www.brivo.com and click Help. 2001 Brivo Systems Inc. All rights reserved. Brivo™ is a trademark of Brivo Systems, Inc. Brivo Systems, Inc. 1925 North Lynn St.• Suite 500 Arlington VA, 22209 © Brivo Systems, Inc. 2001. All rights reserved. Page 1 Brivo ACS Installation Manual Version 1.01 Brivo™ ACS Installation Guide ™ Introduction Access Control is the control through electronic methods over entry to any area that can be secured with a lock and key. Only individuals who are authorized will be granted entry at authorized times. Control of who is allowed to come and go is easily maintained through a central administration panel. The common key is the weakness of the lock and key system. The key is a readily duplicated piece of metal that gives anyone who holds it access to area. With the Brivo™ Access Control System (ACS), the weakness of the lock and key system is overcome through the use of five-digit PIN codes, called “keycodes.” The keycodes are entered by authorized individuals at the Brivo keypad and the individuals are then granted access to the secure area. If a keycode is compromised, the account administrator can disable it immediately and assign a new code to the individual. An additional benefit of access control is access data archiving capability. The Brivo ACS provides real-time visibility of keycode activity and maintains a record of all entries to an area. This record is provided to the account holder quarterly and accessible to authorized personnel at the Brivo ACS website until archived. The Brivo ACS Installation Guide provides all information necessary for installation of the Brivo ACS-2000 and ACS-2100 keypad and control panel. © Brivo Systems, Inc. 2001. All rights reserved. Page 2 Brivo ACS Installation Manual Version 1.01 Parts List Box 1 • ACS Control Panel • Magnetic Door Sensor Box 2 • Keypad • Cutout template for flush mounting • Snap-on keypad faceplate • Antenna kit (boxed separately within this box) • Power Supply (boxed separately within this box) • Installation Worksheet Supplied by Installer • Five CAT 5 cables, maximum length of 20 feet • Ten CAT 5 connector plugs to terminate onto cables • Necessary conduit and conduit fittings if desired, maximum size ¾” • Ten mounting screws (#6 wood screws or Molly bolts) © Brivo Systems, Inc. 2001. All rights reserved. Page 3 Brivo ACS Installation Manual Version 1.01 Diagram: Components List © Brivo Systems, Inc. 2001. All rights reserved. Page 4 Brivo ACS Installation Manual Version 1.01 SAFTEY WARNINGS Fire Safety Notice: Never connect the Brivo keypad or locks to doors without first consulting the applicable fire code. You must consult with and get approval of, local fire officials before installing locks or devices on any doors that may be fire exits. Use of egress push buttons may not be legal. Single action exit may be required. Always obtain proper permits and approvals in writing before installing equipment. FCC RF Exposure Notice: To meet the FCC RF exposure requirement for mobile transmitter end products using the Austin 200160 500C, 0 dBd antenna, ensure that the antenna is at least 20cm (8”) away from the user or nearby persons when transmitting. Notice: Contents of this document are subject to change without notice. Notice: This document and the data herein shall not be duplicated, used or disclosed to others for procurement or manufacturing, except as authorized with the written permission of Brivo Systems, Inc. The information contained within this document or within the product itself is considered the exclusive property and trade secrets of Brivo Systems, Inc. All information in this document or within the hardware and software product themselves is protected by the copyright and/or other intellectual property laws of the United States. Notice: Any use of this product is subject to the Brivo Systems Services Agreement. Please request a copy from Brivo Systems, Inc. and review this agreement carefully. © Brivo Systems, Inc. 2001. All rights reserved. Page 5 Brivo ACS Installation Manual Version 1.01 Installation Steps General Site Survey The Brivo Access Control System has two major components to be installed -the keypad and the ACS Control Panel. Both components work in concert with one another and require cabling between them. A general site survey should occur before any installation work to identify suitable mounting essentials and potential hazards. Ideal conditions to look for include: 1) A stud near the keypad location on the wall. Ideally, the keypad casing should have two screws fastened to a stud. The keypad can be mounted using Molly bolts if no stud is available. 2) A suitable mounting area for the ACS Control Panel within 15 feet of the keypad. The control panel can be mounted on a wall or in the ceiling. Like the keypad, the control panel ideally should be fastened to a stud. 3) A suitable place to mount the ACS Antenna within 15 feet of the ACS Control Panel mounting area. The antenna must be mounted either rightside up or upside down, it should not be mounted on its side and should be at least three feet away from human contact. 4) A 120 V power outlet within 100 feet of the control panel mounting area. The ACS Control Panel requires electrical power. 5) The control panel should be located within 50 feet of the door latch. © Brivo Systems, Inc. 2001. All rights reserved. Page 6 Brivo ACS Installation Manual Version 1.01 Pre-Installation After location has been determined: 1) Select length of CAT-5 cable required 2) Mark both ends of each cable with A, B, C, D, or E 3) Route cables (through a conduit or individually) through the walls in desired manner. Note that the cables eventually will be fed through knocked out holes in the keypad casing and the control panel. Do not terminate the cables with the RJ45 plugs at this time! Keypad Flush (Recessed) Installation vs. Surface Installation The decision to mount on the surface or flush must occur before you determine which of the four holes should be knocked out within the keypad casing. (See Step 2 in “Mounting the Keypad” section). The keypad should be mounted in a location no more than 48 inches from the floor. The keypad can be installed flush against the wall by cutting into the wall and inserting a portion of the keypad casing behind the surface. This will give a more streamlined appearance of the keypad on the wall. The keypad can also be installed on the surface of the wall, which requires minimal cutting into the wall. The keypad can be installed on the surface of the wall with #6 wood screws if a stud is available or anchor (Molly) bolts if no stud is used. © Brivo Systems, Inc. 2001. All rights reserved. Page 7 Brivo ACS Installation Manual Version 1.01 Installation of the ACS Keypad Mounting the Keypad – Flush Mount 1. After determining to go with the flush mount for the keypad, unscrew the four surface screws on the front of keypad. The keypad casing will remain open during the most of the mounting of the keypad. 2. Determine the location for mounting the keypad. The optimal location will allow for the keypad casing to be mounted directly to a stud through either the right or left side. Based on the location of the stud, knockout the 1” hole on the opposite side or the hole on the bottom surface of the box, if preferred for ease of cable routing. 3. Locate the supplied cutout template. Trace around the template in the area of the wall on which you’d like to mount the keypad. 4. Cut around the marking through the wall to a depth of at least 2 ½”, exposing the stud to which you will fasten the keypad casing. 5. Locate the five CAT5 cables and pull each through the knocked out hole in the keypad casing. Use a ¾” conduit connector if required. 6. Mount the side of the keypad box to the stud, using two #6 woodscrews. 7. Terminate each cable with an RJ45 plug. 8. Connect the cables to the jacks on the jumper board located within the keypad casing. (See diagram, Brivo keypad converter board). Cable “A” should be plugged into jack “A”, etc. 9. Locate the lid of keypad casing. On the back of the lid, you will see the back of the LCD display. Locate the cable that is connected to it and plug it into the 16-position header on the keypad jumper board, designator J20. (See diagram, Brivo keypad converter board, and diagram, Keypad casing lid) 10. Locate the fiber optic tail on the lid of the keypad casing. Plug the cable into the LED in the D3 position on the keypad jumper board. (See diagram, Brivo keypad converter board, and diagram, Keypad casing lid) 11. Locate the ribbon cable on the lid on the keypad. Plug it into the 11position connector and position J23 on the keypad jumper board. (See © Brivo Systems, Inc. 2001. All rights reserved. Page 8 Brivo ACS Installation Manual Version 1.01 diagram, Brivo keypad converter board, and diagram, Keypad casing lid). After inserting the ribbon cable in J23, snap down the two-piece connector to lock in the cable. 12. Screw the lid onto the keypad box with the four flat-head #6 screws that are provided. 13. The Brivo keypad is now fully assembled except for the attachable keypad faceplate. DO NOT SNAP THE FACEPLATE ON UNTIL ALL FUNCTIONAL TESTING IS COMPLETE. Mounting the Keypad – Surface Mount 1. After determining to go with the surface mount for the keypad, unscrew the four surface screws on the front of keypad. The keypad casing will remain open during the most of the mounting of the keypad. 2. The cables will exit the keypad casing in the back of the box. Knockout the conduit hole in the back of the keypad casing. 3. Determine a suitable place on the wall to surface mount the keypad. Cut out a 1.5” diameter hole in the wall at the approximate location of the conduit hole on the back of the keypad casing. Pull the cables through the conduit hole, use a ¾” conduit connector if necessary. 4. Mount the keypad casing with four #6 screws, using the countersunk holes. It is ideal to fasten the keypad casing to a stud. If one is not available for a surface mount, the keypad casing can be mounted with four anchor (Molly) bolts. 5. Terminate each cable with an RJ45 plug. 6. Connect the cables to the jacks on the jumper board located within the keypad casing. (Refer to diagram, Brivo keypad converter board). Cable “A” should be plugged into jack “A”, etc. 7. Locate the lid of keypad casing. On the back of the lid, you will see the back of the LCD display. Locate the cable that is connected to it and plug it into the 16-position header on the keypad jumper board, designator J20. (See diagram, Brivo keypad converter board, and diagram, Keypad casing lid). © Brivo Systems, Inc. 2001. All rights reserved. Page 9 Brivo ACS Installation Manual Version 1.01 8. Locate the fiber optic tail on the lid of the keypad casing. Plug the cable into the LED in the D3 position on the keypad jumper board. (See diagram, Brivo keypad converter board, and diagram, Keypad casing lid). 9. Locate the ribbon cable on the lid on the keypad. Plug it into the 11position connector and position J23 on the keypad jumper board. (See diagram, Brivo keypad converter board, and diagram, Keypad casing lid). After inserting the ribbon cable in J23, snap down the two-piece connector to lock in the cable. 10. Screw the lid onto the keypad box with the four flat-head #6 screws that are provided. 11. The Brivo keypad is now fully assembled except for the attachable keypad faceplate. DO NOT SNAP THE FACEPLATE ON UNTIL ALL FUNCTIONAL TESTING IS COMPLETE. Diagram: Keypad Casing Lid © Brivo Systems, Inc. 2001. All rights reserved. Page 10 Brivo ACS Installation Manual Version 1.01 Diagram: Keypad Converter Board © Brivo Systems, Inc. 2001. All rights reserved. Page 11 Brivo ACS Installation Manual Version 1.01 Installation of ACS Control Panel Mounting the Control Panel 1. Locate the control panel. Unscrew the four corner screws and remove the lid of the control panel casing. 2. Note the location where you want to mount the control panel. The control panel can be mounted on a wall or in the ceiling. 3. Locate the five CAT5 cables and pull them through the larger hole in the bottom of the control panel casing. Use a ¾’’ conduit connector on the larger hole, if necessary. 4. Mount the control panel casing to the wall, using four #6 screws. It is ideal to fasten the control box to a stud. If one is not available, the control box can be mounted with four anchor (Molly) bolts. If mounting in the ceiling, locate a stud and fasten the control panel casing to it. 5. After mounting the control panel casing to the wall or in the ceiling, terminate the cables to RJ45 plugs and plug them into the control panel jumper board in their proper positions, cable “A” plugs into jack “A”, etc. (See diagram, Control panel converter board). Do not replace the lid of the control panel casing yet. 6. Locate the magnetic switch and install it in a convenient place over the door, following the manufacturer’s instructions. The magnet (piece with no wires) should be attached to the door and the switch (contains two wires) to the doorframe above the door. Screws are provided to securely fasten both pieces of the switch. 7. Attach two, 26-22 gauge wires (provided by installer) to the magnetic door sensor and route them to the Control Panel. Pull the two wires into the control panel casing through the smaller hole. The wires will be used to sense the door open/close status. (See diagram, Control panel converter board). 8. Locate the black and yellow wires inside the control panel jumper board. Use an appropriate connector to connect the wires from the magnetic switch to the black and yellow wires. (See diagram, Control panel converter board). 9. Locate the orange, blue and green wires inside the control panel jumper board. The three contacts are connected to a SPST relay. © Brivo Systems, Inc. 2001. All rights reserved. Page 12 Brivo ACS Installation Manual Version 1.01 The blue wire is connected to the common contact, orange wire is connected to the normally open contact and green wire is connected to the normally closed contact. 10. Pull the two wires into the control panel casing through the smaller hole. The wires will be used to control the door latch via the relay output. (See diagram, Control panel jumper board). Diagram: Control Panel Converter Board © Brivo Systems, Inc. 2001. All rights reserved. Page 13 Brivo ACS Installation Manual Version 1.01 Installation of the ACS Power Supply Mounting the Power Supply 1. Locate the power supply kit. Note that the power supply will be plugged into a 120 volt AC socket. Mount the power supply to the wall an appropriate distance from the outlet, using anchor bolts. 2. There will be 100 feet of cable. WARNING! Do not plug the power supply into the AC socket yet. 3. Dress the cable up the wall, route it to the control panel. 4. Pull the power cable through the smaller hole in the bottom of the control panel. Properly terminate the cable with the supplied terminals and install the 3-position connector housing onto the end of the cable. 5. Plug the terminated cable into the power connector on the control panel main board in the position designated J5. (See diagram, Control Panel Main PC Board). 6. Plug the power supply cable into the AC socket. 7. Locate the SW4 switch on the main control panel board and switch it “on”. If AC power is present the green LED marked AC/D4 located near the RJ45 jacks on the jumper board will be on. (See diagram, Control Panel Main PC Board). 8. Wait 5 minutes to allow the super capacitors to become fully charged. © Brivo Systems, Inc. 2001. All rights reserved. Page 14 Brivo ACS Installation Manual Version 1.01 Installation of the ACS Antenna Mounting the Antenna and Performing Functional Testing FCC RF Exposure Notice: To meet the FCC RF exposure requirement for mobile transmitter end products using the Austin 200160 500C, 0 dBd antenna, ensure that the antenna is at least 20cm (8”) away from the user or nearby persons when transmitting. 1. Locate the antenna kit. In it you will find the antenna, the antenna mounting kit, and the mounting bracket. 2. Take the antenna and the mounting kit and screw them together through the 3/4'” hole in the antenna mounting bracket. 3. There is a jack originating on the top of the control panel casing. Plug the antenna cable into this jack. 4. Now you are ready to perform functional testing of the system. First, open the door and prop it open. 5. Return to the control panel and depress the “Reset” button, which is designated switch SW3. (See diagram, Control Panel Main PC Board). 6. Return to the keypad user interface and close the door. Press enter to start functional testing. The first screen is a character test. Verify all characters appear normal and press the down arrow to advance to the next screen. 7. The second screen is a pixel test. Verify that all the pixels rectangles are complete and press the down arrow to advance to the next screen. 8. The third screen is a keypad test. Press each button on the keypad and verify that the corresponding character is displayed. After every key is pressed, press the down arrow to advance to the next screen. 9. The fourth screen is the door sensor/ door open test. Press enter to test the door open mechanism and open the door. Verify the door open/close status on the screen as open. Close the door and verify the door open/close status as closed. Press enter to re-open the door and prop it open. Press the down arrow to advance to the next screen. 10. The fifth screen is the sensor test. Verify that primary power is available. Press the down arrow to advance to the next screen. © Brivo Systems, Inc. 2001. All rights reserved. Page 15 Brivo ACS Installation Manual Version 1.01 11. The sixth screen is the light sensor test. Press the up arrow, then the down arrow to advance to the next screen. 12. The seventh screen is the IR sensor test. Press the up arrow, then the down arrow to advance to the next screen. 13. The eighth screen provides the antenna signal strength. With the antenna oriented right side up or upside down, not on its side, find the best signal strength as indicated on the keypad display. NOTE: -50dbm is better than –100dbm. A reading of –256dbm indicates no signal is reaching the system. 14. Once you’ve found a suitable mounting place for the with the best signal strength, mount the antenna to the wall using two #6 screws. Now replace the front of the control panel using the four corner screws. Press the down arrow to advance to the next screen. 15. The ninth screen contains the door id# and ESN number. Record the door id # on the installation worksheet. Press the down arrow to complete the functional testing. NOTE: The BRN screen will now be displayed until the device is registered. Additional antenna adjustments can be made at this point by pressing enter to update the current signal strength. 16. Snap the keypad faceplate on the keypad unit. 17. Locate the Installation Worksheet. Complete the checklist on the worksheet, paying close attention to copying the Door ID number correctly, and deliver it to the customer. 18. Alert the customer that they can now register the door using the door ID # provided on the Installation Worksheet. © Brivo Systems, Inc. 2001. All rights reserved. Page 16 Brivo ACS Installation Manual Version 1.01 Diagram: Control Panel Main PC Board © Brivo Systems, Inc. 2001. All rights reserved. Page 17 Brivo ACS Installation Manual Version 1.01 Product Specifications Models ACS-2000 & ACS-2100 Size Keypad: 7.5” x 7.5” x 0.75” (flush mounted) 7.5” x 7.5” x 2.75” (surface mounted) Control and Communication Panel: 14.25” x 10.75” x 5.25” Electrical Transformer Input: Transformer Output: Operating Temperature: Keypad: Output Relay Format: Output Relay Ratings: Battery Backup: Modem: 120VAC, 60Hz, 1 Amp 12VAC, 44 Watts –20 to +70 degrees Celcius Membrane with backlit LCD display NO, NC, Common contact set 0.4Amp, 125VAC, 2Amp, 30VDC 6 “D Cell” Alkaline batteries (included) Rim R902M Cable Types Keypad to Control Panel: Door Closed Monitor Switch: Door Latch / Lock: Cat5 or Cat5E (5 cables) 2 conductor bell wire See Latch / Lock Manufacturer Data Cable Lengths Keypad to Control Panel: Control Panel to Door Closed Switch: Control Panel to Latch / Lock: Antenna Coax Cable (supplied): 20 feet maximum 60 feet maximum See Latch / Lock Manufacturer Data 15 feet maximum Other Clock: Color / Finish: Suede Real-time clock Keypad Bezel: Pantone, Dark Grey 433C / Keypad Box: Pantone Black 2C / Suede Control Panel: Pantone Dark Grey 433C / Suede Certifications FCC and UL certifications are pending. Specifications are subject to change without notice. Brivo reserves the right to discontinue any product without notice. Brivo Systems, Inc. • 1925 North Lynn Street, Suite 500 • Arlington, VA 22209 • 866.MY.BRIVO • www.brivo.com 2001 Brivo Systems, Inc. © Brivo Systems, Inc. 2001. All rights reserved. Page 18
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 18 Creator : Brivo ACS Installation Guide 7.27.01.doc - Microsoft Word Create Date : 2001:08:09 16:19:43 Title : Brivo ACS Installation Guide 7.27.01.doc Author : ETemplet Producer : Acrobat PDFWriter 4.05 for Windows NTEXIF Metadata provided by EXIF.tools