Broadcom BRCM1044 802.11g Wireless LAN + BluetoothPCI-E Mini Card User Manual Host 2 of 2
Broadcom Corporation 802.11g Wireless LAN + BluetoothPCI-E Mini Card Host 2 of 2
Broadcom >
Contents
Host user manual 2 of 2
Regulatory, Safety and
Environmental Notices
User Guide
© Copyright 2008–2010 Hewlett-Packard
Development Company, L.P.
Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard
Company under license. ENERGY STAR is
a registered mark owned by the U.S.
government. Java is a trademark of Sun
Microsystems. Microsoft, Windows, and
Windows Vista are U.S. registered
trademarks of Microsoft Corporation.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
Ninth Edition: December 2010
First Edition: August 2008
Document Part Number: 506242-009
Table of contents
1 Regulatory notices .......................................................................................................................................... 1
Federal Communications Commission notice ...................................................................................... 2
Modifications ........................................................................................................................ 2
Cables .................................................................................................................................. 2
Declaration of Conformity for products marked with the FCC logo (United States only) ..... 2
Products with wireless LAN devices or HP Mobile Broadband Modules ............................. 3
Brazil notice .......................................................................................................................................... 4
Canada notices .................................................................................................................................... 4
Avis Canadien ...................................................................................................................................... 4
European Union Regulatory notices ..................................................................................................... 4
Products with HP Mobile Broadband Modules .................................................................... 6
Ergonomics notice ............................................................................................................... 6
Germany ............................................................................................................. 6
Japan notices ....................................................................................................................................... 7
Wireless LAN 802.11b devices ............................................................................................ 7
Wireless LAN 802.11g devices ............................................................................................ 7
Bluetooth devices ................................................................................................................ 8
Wireless LAN, Wireless WAN, and Bluetooth certification markings ................................... 8
South Korea notice ............................................................................................................................... 8
Mexico notice ....................................................................................................................................... 8
Singapore wireless notice .................................................................................................................... 8
Thailand WWAN wireless notice .......................................................................................................... 9
Taiwan notices ..................................................................................................................................... 9
Wireless LAN 802.11a devices ............................................................................................ 9
Wireless LAN 802.11b devices ............................................................................................ 9
Vietnam Compliance Marking Notice ................................................................................................... 9
Airline travel notice ............................................................................................................................. 10
Battery notices .................................................................................................................................... 10
ENERGY STAR compliance .............................................................................................................. 10
Laser compliance ............................................................................................................................... 11
Modem notices ................................................................................................................................... 11
Telecommunications device approvals .............................................................................. 12
U.S. modem statements .................................................................................................... 12
U.S. modem declarations .................................................................................................. 14
iii
Canada modem statements ............................................................................................... 15
Japan modem statements ................................................................................................. 16
New Zealand modem statements ...................................................................................... 16
Voice support .................................................................................................... 17
Power cord notice ............................................................................................................................... 17
Japan power cord notice .................................................................................................... 17
Macrovision Corporation notice .......................................................................................................... 17
2 Safety notices ................................................................................................................................................ 18
Heat-related safety warning notice ..................................................................................................... 18
Potential safety conditions notice ....................................................................................................... 18
Battery notices .................................................................................................................................... 18
Headset and earphone volume level notice ....................................................................................... 19
Power cord notices ............................................................................................................................. 19
Cleaning the keyboard ....................................................................................................................... 19
Travel notice ....................................................................................................................................... 19
Norway and Sweden: Cable grounding notice for products with a TV tuner ...................................... 20
3 Environmental notices ................................................................................................................................. 21
Electronic hardware and battery recycling ......................................................................................... 21
Disposal of waste equipment by users in private households in the European Union ....................... 21
Chemical substances ......................................................................................................................... 21
China material content declarations ................................................................................................... 22
Japan material content declaration .................................................................................................... 24
Turkey EEE regulation ....................................................................................................................... 24
United States mercury disposal .......................................................................................................... 25
Perchlorate material—special handling may apply ............................................................................ 25
Index ................................................................................................................................................................... 26
iv
1 Regulatory notices
This guide provides country- and region-specific non-wireless and wireless regulatory notices and
compliance information for the computer product. Some of these notices may not apply to your
product.
One or more integrated wireless devices may be installed. In some environments, the use of wireless
devices may be restricted. Such restrictions may apply on-board airplanes, in hospitals, near
explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use
of this product, ask for authorization to use it before you turn it on.
To identify a hardware device such as a wireless LAN (WLAN) network device, choose the procedure
below that corresponds to the operating system running on your computer.
For Windows® XP Professional and Windows XP Home, follow these steps:
1. Select Start > My Computer.
2. If the left pane, select View System Information > Hardware tab > Device Manager.
For Windows Vista®, follow these steps:
1. Select Start > Computer > System properties.
2. In the left pane, click Device Manager.
For later Windows operating systems, such as Windows 7, follow these steps:
▲Select Start > Control Panel > System and Security > Device Manager.
For non-Windows operating systems, follow the instructions provided by your operating system to
identify a hardware device such as a wireless LAN (WLAN) network device.
Regulatory markings for your country or region may be located on the bottom of the product, either
under the battery, under a user-removable door (or some other user-accessible location), or on the
wireless or modem module.
To view the FCC IDs for any radio modules in your notebook (Bluetooth®, WLAN, or WWAN), follow
these steps:
1. Turn on or restart the computer, and then press esc while the "Press the ESC key for Startup
Menu" message is displayed at the bottom of the screen.
2. Press f10 to enter BIOS Setup.
3. Select the System Configuration menu.
1
The FCC IDs are displayed at the bottom of the screen.
CAUTION: Devices not for sale or use in the United States may not have an FCC ID.
Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that
are not expressly approved by HP may void the user's authority to operate the equipment.
Cables
To maintain compliance with FCC Rules and Regulations, connections to this device must be made
with shielded cables having metallic RFI/EMI connector hoods.
Declaration of Conformity for products marked with the FCC logo
(United States only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
2 Chapter 1 Regulatory notices
If you have questions about the product that are not related to this declaration, write to
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, TX 77269-2000
For questions regarding this FCC declaration, write to
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, TX 77269-2000
or call HP at 281-514-3333
To identify your product, refer to the part, series, or model number located on the product.
Products with wireless LAN devices or HP Mobile Broadband Modules
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is
below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a
manner that the potential for human contact is minimized during normal operation of tablet PCs and
notebook computers.
During normal operation of tablet PCs and notebook computers with displays equal to or less than 12
inches: To avoid the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antennas should not be less than 2.5 cm (1 inch). To identify the location of the
wireless antennas, refer to the computer user guides. To access the user guides, select Start > Help
and Support > User Guides.
During normal operation of notebook computers with displays greater than 12 inches: To avoid the
possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas
should not be less than 20 cm (8 inches), including when the computer display is closed. To identify
the location of the wireless antennas, refer to the computer user guides. To access the user guides,
select Start > Help and Support > User Guides.
CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to
its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used
indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful
interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user
of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference
with and/or damage to this device.
Federal Communications Commission notice 3
Brazil notice
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a
sistemas operando em caráter primário.
Este equipamento atende aos limites de Taxa de Absorção Específica referente à exposição a
campos elétricos, magnéticos e eletromagnéticos de radiofreqüências adotados pela ANATEL.
Canada notices
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations. If this device has WLAN or Bluetooth capability, the device complies with
RSS 210 of Industry Canada. Wireless operation is subject to two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to
its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be
used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful
interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user
of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference
with and/or damage to this device.
The antennas for this device are not replaceable. Any attempt at user access will damage your
computer.
Avis Canadien
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
European Union Regulatory notices
Products bearing the CE marking comply with the following EU Directives:
●Low Voltage Directive 2006/95/EC
●EMC Directive 2004/108/EC
●Ecodesign Directive 2009/125/EC where applicable
CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided by
HP.
If this product has wired and/or wireless telecommunications functionality, it also complies with the
essential requirements of EU Directive R&TTE Directive 1999/5/EC.
Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or
4 Chapter 1 Regulatory notices
product family and available (in English only) either within the product documentation or at the
following Web site: www.hp.eu/certificates (type the product number in the search box).
The compliance is indicated by one of the following conformity markings placed on the product:
For non-telecommunications products and for EU harmonized telecommunications products, such as
Bluetooth®, within power class below 10 mW.
For EU non-harmonized telecommunications products (if applicable, a 4-digit notified body number is
inserted between CE and ! (the exclamation mark).
Please refer to the regulatory label provided on the product.
The telecommunications functionality of this product may be used in the following EU and EFTA
countries: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden,
Switzerland, and United Kingdom.
The telephone connector (not available for all products) is intended for connection to analog
telephone networks.
NOTE: For products with wireless LAN devices, some countries may have specific obligations or
special requirements about the operation of wireless LAN networks such as indoor use only or
restrictions of the channels available. Be sure that the country settings of the wireless network are
correct.
In France, certain restrictions apply for the 2.4-GHz wireless LAN operation of this product. This
product may be used indoors for the entire 2400-MHz to 2483.5-MHz frequency band (channels 1 to
13). For outdoor use, only the 2400-MHz to 2454-MHz frequency band (channels 1 to 7) may be
used. For the latest requirements, see http://www.arcep.fr.
The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE,
Herrenberger Strasse 140, 71034 Boeblingen, GERMANY.
European Union Regulatory notices 5
Products with HP Mobile Broadband Modules
THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO FREQUENCY
RADIATION.
The HP Mobile Broadband Module in your notebook is a radio transmitter and receiver. The device is
designed not to exceed the limits for exposure to radio frequency (RF) recommended by international
guidelines (ICNIRP). These limits are part of comprehensive guidelines that establish permitted levels
of RF radiation for the general population. The guidelines were developed by independent scientific
organizations through periodic and thorough evaluation of scientific studies. The device also meets
the European R&TTE directives, including the protection of the health and the safety of the user and
any other person.
The exposure standard for mobile devices employs a unit of measurement known as the Specific
Absorption Rate (SAR).* The SAR was obtained by testing the device at standard operating positions
with the device transmitting at its highest certified power level in all tested frequency bands. The
actual SAR of the device while operating can be well below the maximum value, because the device
operates at multiple power levels and uses only the power required to reach the network.
When installed in the notebook computer, this device meets RF exposure guidelines when the
antennas are positioned at a minimum distance from the body. In order to transmit data or messages,
this device requires a quality connection to the network. In some cases, transmission of data or
messages may be delayed until such a connection becomes available. Be sure that the
recommended distance is observed until the transmission is complete.
*The non-FCC, international guidelines state that the SAR limit for mobile devices used by the public
is 2.0 watts/kilogram (W/kg) averaged over 10 grams of body tissue. The guidelines incorporate a
substantial margin of safety to give additional protection for the public and to account for any
variations in measurements. SAR values may vary depending on national reporting requirements and
the network band.
This equipment incorporates a radio transmitting device. In normal use, a separation distance of 20
cm ensures that radio frequency exposure levels comply with the Australian and New Zealand
Standards.
Ergonomics notice
Germany
Mobile computers bearing the "GS" approval mark meet the ergonomic requirements and are suitable
only for short-time use of VDU tasks. When a mobile computer is used for display work tasks where
the Visual Display Unit (VDU) Directive 90/270/EEC is applicable, an adequate external keyboard is
required. Depending on the application and task, an adequate external monitor may also be
necessary to attain working conditions comparable to a workstation setup.
Ref: EK1-ITB 2000:2008
This device is intended for use at visual display workplaces in compliance with BildscharbV, only with
external keyboard and adequate external monitor.
During mobile use with disadvantageous illumination conditions (e.g. direct sun light) reflections may
occur which result in reduced readability.
6 Chapter 1 Regulatory notices
Mobile Computer, welche das "GS" Zeichen tragen, entsprechen den ergonomischen Anforderungen
und sind nur für kurzzeitige Benutzung von Bildschirmarbeitsaufgaben geeignet. Wird ein mobiler
Computer für Bildschirmarbeitsaufgaben verwendet, wo die Richtlinie 90/270/EEG
(Bildschirmarbeitsrichtlinie) anzuwenden ist, wird eine geeignete externe Tastatur notwendig.
Abhängig von der Anwendung und der Aufgabe kann ein geeigneter externer Monitor erforderlich
sein, um vergleichbare Arbeitsbedingungen zu einem stationären Arbeitsplatz zu erreichen.
Ref: EK1-ITB 2000:2008
Das Gerät ist für die Benutzung am Bildschirmarbeitsplatz gemäß BildscharbV nur mit externer
Tastatur und geeignetem Monitor vorgesehen.
Bei mobiler Nutzung mit ungünstigen Lichtverhältnissen (z.B. direkte Sonneneinstrahlung) kann es zu
Reflexionen und damit zu Einschränkungen der Lesbarkeit der dargestellten Zeichen kommen.
Japan notices
Wireless LAN 802.11b devices
Wireless LAN 802.11g devices
Japan notices 7
Bluetooth devices
Wireless LAN, Wireless WAN, and Bluetooth certification markings
This product contains certified radio equipment.
South Korea notice
Mexico notice
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) este equipo puede que
no cause interferencia y (2) este equipo debe aceptar cualquier interferencia, incluyendo interferencia
que pueda ser causada por la operación no deseada.
Singapore wireless notice
Turn off any WWAN devices while you are onboard aircraft. The use of these devices onboard aircraft
is illegal, may be dangerous to the operation of the aircraft, and may disrupt the cellular network.
Failure to observe this instruction may lead to suspension or denial of cellular services to the
offender, or legal action, or both.
Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where
blasting operations are in progress.
As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of
the equipment and for the safety of personnel, no part of the human body should be allowed to come
too close to the antennas during operation of the equipment.
This device has been designed to comply with applicable requirements for exposure to radio waves,
based on scientific guidelines that include margins intended to assure the safety of all people,
regardless of health and age. These radio wave exposure guidelines employ a unit of measurement
known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized
methods, with the phone transmitting at its highest certified power level in all used frequency bands.
The SAR data information is based on CENELEC's standards EN50360 and EN50361, which use the
limit of 2 watts per kilogram, averaged over 10 grams of tissue.
8 Chapter 1 Regulatory notices
Thailand WWAN wireless notice
This telecom equipment has complied with NTC regulations.
Taiwan notices
Wireless LAN 802.11a devices
Wireless LAN 802.11b devices
Vietnam Compliance Marking Notice
This marking is for applicable products only.
Thailand WWAN wireless notice 9
Airline travel notice
Use of electronic equipment onboard commercial aircraft is at the discretion of the airline.
Battery notices
WARNING! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
For information about removing a battery, refer to the user guide included with the product.
ENERGY STAR compliance
HP computers marked with the ENERGY STAR® logo are qualified with the applicable U.S.
Environmental Protection Agency (EPA) ENERGY STAR specifications for computers. The EPA
ENERGY STAR logo does not imply endorsement by the EPA. As an ENERGY STAR Partner,
Hewlett-Packard Company has determined that the products marked with the ENERGY STAR logo
are ENERGY STAR qualified as per the applicable ENERGY STAR guidelines for energy efficiency.
The following logo will appear on all ENERGY STAR qualified computers:
The ENERGY STAR program for computers was created by the EPA to promote energy efficiency
and reduce air pollution through more energy-efficient equipment in homes, offices, and factories.
One way that products achieve this goal is by using the Microsoft® Windows® power management
feature to reduce power consumption when the product is not in use.
The power management feature allows the computer to initiate a low-power or “Sleep” mode after a
period of user inactivity. When used with an external ENERGY STAR qualified monitor, this feature
also supports similar power management features of the monitor. To take advantage of these
potential energy savings, the power management feature has been preset to behave in the following
ways when the system is operating on AC power:
●Turn off the display after 15 minutes
●Initiate Sleep after 30 minutes
10 Chapter 1 Regulatory notices
The computer exits Sleep when the power/Sleep button is pressed. When the Wake On LAN (WOL)
feature is enabled, the computer can also exit Sleep in response to a network signal.
Additional information on the potential energy and financial savings of the power management feature
can be found on the EPA ENERGY STAR Power Management Web site at
http://www.energystar.gov/powermanagement.
Additional information on the ENERGY STAR program and its environmental benefits are available
on the EPA ENERGY STAR Web site at http://www.energystar.gov.
Laser compliance
WARNING! Use of controls or adjustments, or performance of procedures other than those
specified in the laser product installation guide, may result in hazardous radiation exposure. To
reduce the risk of exposure to hazardous radiation:
Do not try to open the module enclosure. There are no user-serviceable components inside.
Do not operate controls, make adjustments, or perform procedures to the laser device other than
those specified in the laser product installation guide.
Allow only authorized service providers to repair the unit.
This product may be provided with an optical storage device (for example, a CD or DVD drive) and/or
a fiber optic transceiver. Each of these devices that contain a laser is classified as a Class 1 Laser
Product in accordance with IEC 60825-1 and meets the requirements for safety of that standard.
Each laser product complies with US FDA regulations of 21 CFR 1040.10 and 1040.11 or complies
with those regulations except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007.
Modem notices
WARNING! To reduce the risk of fire, electric shock, and injury to persons when using this device,
always follow basic safety precautions, including the following:
Do not use this product near water—for example, near a bathtub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
Avoid using this product during an electrical storm. There is a remote risk of electric shock from
lightning.
Do not use this product to report a gas leak while in the vicinity of the leak.
Always disconnect the modem cable before opening the equipment enclosure or touching an
uninsulated modem cable, jack, or internal component.
If this product was not provided with a telephone line cord, use only No. 26 AWG or larger
telecommunication line cord.
Do not plug a modem or telephone cable into the RJ-45 (network) jack.
SAVE THESE INSTRUCTIONS
Laser compliance 11
Telecommunications device approvals
The telecommunications device in the computer is approved for connection to the telephone network
in the countries and regions whose approval markings are indicated on the product label located on
the bottom of the computer or on the modem.
Refer to the user guide included with the product to ensure that the product is configured for the
country or region in which the product is located. Selecting a country or region other than the one in
which it is located may cause the modem to be configured in a way that violates the
telecommunication regulations/laws of that country or region. In addition, the modem may not function
properly if the correct country or region selection is not made. If, when you select a country or region,
a message appears that states that the country or region is not supported, this means that the
modem has not been approved for use in this country or region and thus should not be used.
U.S. modem statements
This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA.
On the bottom of the computer or on the modem is a label that contains, among other information, a
product identifier in the format US:AAAEQ##TXXXX. Provide this information to the telephone
company if you are requested to do so.
Applicable certification jack USOC = RJ11C. A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with
this product. It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all locations, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact the
local telephone company. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately
shown on the label.
If this HP equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But, if advance notice isn't
practical, the telephone company will notify you as soon as possible. Also, you will be advised of your
right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes to its facilities, equipment, operations, or procedures
that could affect the operation of the equipment. If this happens, the telephone company will provide
advance notice in order for you to make necessary modifications to maintain uninterrupted telephone
service.
If trouble is experienced with this equipment, call technical support. If the equipment is causing harm
to the telephone network, the telephone company may request that you disconnect the equipment
until the problem is resolved. You should perform repairs only to the equipment specifically discussed
in the “Troubleshooting” section of the user guide, if one is provided.
Connection to party line service is subject to state tariffs. Contact the state public utility commission,
public service commission, or corporation commission for information.
12 Chapter 1 Regulatory notices
If your home has specially wired alarm equipment connected to the telephone line, ensure that the
installation of this HP equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer
or other electronic device, including a fax machine, to send any message unless such message
clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the
transmission, the date and time it is sent and an identification of the business, other entity, or other
individual sending the message, and the telephone number of the sending machine or such business,
other entity, or individual. (The telephone number provided may not be a 900 number or any other
number for which charges exceed local or long-distance transmission charges).
In order to program this information into your fax machine, you should complete the steps outlined in
the faxing software instructions.
Modem notices 13
U.S. modem declarations
Refer to the following modem vendor declarations for the modem device installed in your computer:
14 Chapter 1 Regulatory notices
Canada modem statements
This equipment meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to
be connected to a telephone interface. The termination on an interface may consist of any
combination of devices, subject only to the requirement that the sum of the RENs of all devices does
not exceed 5. The REN for this terminal equipment is 1.0.
Modem notices 15
Japan modem statements
If the computer does not have the Japanese certification mark on the bottom of the computer, refer to
the appropriate certification marking below.
The Japanese certification mark for the V.92 56K Data/Fax Modem is below:
New Zealand modem statements
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has
accepted that the item complies with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it
provides no assurance that any item will work correctly in all respects with another item of
Telepermitted equipment of a different make or model, nor does it imply that any product is
compatible with all of Telecom's network services.
This equipment is not capable, under all operating conditions, of correct operation at the higher
speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such
circumstances.
If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will
always continue to support pulse dialing.
Use of pulse dialing, when this equipment is connected to the same line as other equipment, may
give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems
occur, the user should not contact the Telecom Faults Service.
Some parameters required for compliance with Telecom's Telepermit requirements are dependent on
the equipment (PC) associated with this device. The associated equipment shall be set to operate
within the following limits for compliance with Telecom's Specifications:
a. There shall be no more than 10 call attempts to the same number within any 30-minute period
for any single manual call initiation.
b. The equipment shall go on-hook for a period of not less than 30 seconds between the end of
one attempt and the beginning of the next attempt.
c. Where automatic calls are made to different numbers, the equipment shall be set to go on-hook
for a period of not less than 5 seconds between the end of one attempt and the beginning of the
next attempt.
d. The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of
receipt of ringing (So set between 2 and 10).
16 Chapter 1 Regulatory notices
Voice support
All persons using this device for recording telephone conversations shall comply with New Zealand
law. This requires that at least one party to the conversation is aware that it is being recorded. In
addition, the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the
nature of the personal information collected, the purpose for its collection, how it is to be used, and
what is disclosed to any other party.
This equipment shall not be set to make automatic calls to the Telecom ‘111' Emergency Service.
Power cord notice
If you were not provided with a power cord for the computer or for an external power accessory
intended for use with the computer, you should purchase a power cord that is approved for use in
your country or region.
The power cord must be rated for the product and for the voltage and current marked on the product's
electrical ratings label. The voltage and current rating of the cord should be greater than the voltage
and current rating marked on the product. In addition, the diameter of the wire must be a minimum of
0.75 mm²/18AWG, and the length of the cord must be between 1.5 m (5 ft) and 2 m (6½ ft). If you
have questions about the type of power cord to use, contact your authorized service provider.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon
it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the
cord exits from the product.
Japan power cord notice
Macrovision Corporation notice
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation and is intended for home and other limited viewing uses only, unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Power cord notice 17
2 Safety notices
Heat-related safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on
a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to
contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer
and the AC adapter comply with the user-accessible surface temperature limits defined by the
International Standard for Safety of Information Technology Equipment (IEC 60950).
Potential safety conditions notice
If you notice any of the following conditions (or if you have other safety concerns), do not use the
computer: crackling, hissing, or popping sound, or a strong odor or smoke coming from the computer.
It is normal for these conditions to appear when an internal electronic component fails in a safe and
controlled manner. However, these conditions may also indicate a potential safety issue. Do not
assume it is a safe failure. Turn off the computer, disconnect it from its power source, and contact
technical support for assistance.
Battery notices
WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short
external contacts; do not dispose of in fire or water.
WARNING! Keep the battery away from children.
WARNING! To reduce potential safety issues, only the battery provided with the computer, a
replacement battery provided by HP, or a compatible battery purchased as an accessory from HP
should be used with the computer.
18 Chapter 2 Safety notices
Headset and earphone volume level notice
WARNING! Listening to music at high volume levels and for extended durations can damage one’s
hearing. To reduce the risk of hearing damage, lower the volume to a safe, comfortable level and
reduce the amount of time listening at high levels.
For your own safety, before using headsets or earphones, always reset the volume. Some
headphones are louder than other headphones, even if the volume control setting is the same.
Changing the default audio or equalizer settings might lead to higher volume and should only be done
with caution.
For your own safety, headsets or earphones used with this product should comply with the
headphone limits in EN 50332-2.
If the computer includes a headset or earphones, this combination is in compliance to EN 50332-1.
Power cord notices
WARNING! To reduce the risk of electric shock or damage to the equipment:
Plug the power cord into an AC outlet that is easily accessible at all times.
Disconnect power from the computer by unplugging the power cord from the AC outlet (not by
unplugging the power cord from the computer).
If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-
pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter.
The grounding pin is an important safety feature.
WARNING! To reduce potential safety issues, only the AC adapter provided with the computer, a
replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP
should be used with the computer.
Cleaning the keyboard
WARNING! To reduce the risk of electric shock or damage to internal components, do not use a
vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris
on the keyboard surface. Clean the keyboard regularly to prevent keys from sticking and to remove
dust, lint, and particles that can become trapped beneath the keys. A can of compressed air with a
straw extension can be used to blow air around and under the keys to loosen and remove debris.
Travel notice
WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to
power the computer with a voltage converter kit sold for appliances.
Headset and earphone volume level notice 19
Norway and Sweden: Cable grounding notice for
products with a TV tuner
CAUTION: To reduce potential safety issues, use a galvanic isolator when connecting to a cable
distribution system.
20 Chapter 2 Safety notices
3 Environmental notices
This chapter provides country- and region-specific environmental notices and compliance information.
Some of these notices may not apply to your product.
Electronic hardware and battery recycling
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and
rechargeable batteries. For more information about recycling programs, see the HP Web site at
http://www.hp.com/recycle.
Disposal of waste equipment by users in private
households in the European Union
This symbol means do not dispose of your product with your other household waste. Instead, you
should protect human health and the environment by handing over your waste equipment to a
designated collection point for the recycling of waste electrical and electronic equipment. For more
information, please contact your household waste disposal service.
Chemical substances
HP is committed to providing our customers with information about the chemical substances in our
products as needed to comply with legal requirements such as REACH (Regulation EC No
1907/2006 of the European Parliament and the Council). A chemical information report for this
product can be found at http://www.hp.com/go/reach.
Electronic hardware and battery recycling 21
China material content declarations
The Table of Toxic and Hazardous Substances/Elements and their Content
As required by China's Management Methods for Controlling Pollution by Electronic Information
Products
Toxic and Hazardous Substances and Elements
Part Name
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr(VI))
Polybrominated
biphenyls (PBB)
Polybrominated
diphenyl ethers
(PBDE)
Battery X O O O O O
Cables X O O O O O
Camera X O O O O O
Chassis/Other X O O O O O
Flash memory card reader X O O O O O
Floppy disk drive X O O O O O
Hard disk drive X O O O O O
Headphones X O O O O O
I/O PCAs X O O O O O
22 Chapter 3 Environmental notices
Toxic and Hazardous Substances and Elements
Part Name
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr(VI))
Polybrominated
biphenyls (PBB)
Polybrominated
diphenyl ethers
(PBDE)
Keyboard X O O O O O
Liquid crystal display
(LCD) panel
XX O O O O
Media (CD/DVD/floppy) O O O O O O
Memory X O O O O O
Motherboard, processor,
heat sinks
XO O O O O
Mouse X O O O O O
Optical disk drive X O O O O O
Optional docking device X O O O O O
Power adapter X O O O O O
Power supply X O O O O O
Remote control X O O O O O
Smart card/Java™ card
reader
XO O O O O
Speakers, external X O O O O O
TV tuner X O O O O O
USB flash memory drive X O O O O O
USB hub X O O O O O
Web camera X O O O O O
Wireless receiver X O O O O O
Wireless cards X O O O O O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the
limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part
is above the limit requirement in SJ/T11363-2006.
All parts named in this table with an X are in compliance with the European Union's RoHS Legislation “Directive 2002/95/EC
of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous
substances in electrical and electronic equipment” and its amendments.
NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal operating use
conditions of the product such as temperature and humidity.
China material content declarations 23
Japan material content declaration
A Japanese regulatory requirement, defined by specification JIS C 0950, 2008, mandates that
manufacturers provide material content declarations for certain categories of electronic products
offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, see
the HP Web site at http://www.hp.com/go/jisc0950.
Turkey EEE regulation
In Conformity with the EEE regulation
EEE Yönetmeliğine Uygundur
24 Chapter 3 Environmental notices
United States mercury disposal
This HP product contains the following materials that might require special handling at end-of-life:
●Mercury in the fluorescent lamp in the display LCD
Disposal of mercury can be regulated because of environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries Alliance (EIA)
http://www.eiae.org.
NOTE: Notebook computers configured with LED backlights do not contain mercury lamps.
Perchlorate material—special handling may apply
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
This product’s real-time clock battery or coin cell battery may contain perchlorate and may require
special handling when recycled or disposed of in California.
United States mercury disposal 25
Index
A
airline travel notice 10
B
battery notice 10, 18, 25
battery recycling 21
Brazil notice 4
C
cable grounding notice 20
Canada modem statement 15
Canada notices 4
Canadian French notices 4
China Material Content
Declarations 22
D
Declaration of Conformity 2
disposal notices
battery 10, 25
equipment 21
mercury 25
E
electronic hardware and battery
recycling 21
ENERGY STAR compliance 10
environmental notices 21
equipment disposal notice 21
ergonomics notice 6
European Union notices 4
F
Federal Communications
Commission
cables 2
modifications 2
notice 2
G
GS Notice 6
H
hardware device, identifying 1
headset and earphone volume
level notice 19
J
Japan material content
declaration 24
Japan modem statement 16
Japan notice 7
Japan power cord notice 17
K
keyboard notice 19
L
laser safety notice 11
M
Macrovision Corporation notice
17
mercury disposal notice 25
Mexico wireless notice 8
modem notices 11
modem statements
Canada 15
Japan 16
New Zealand 16
U.S. 12
modifications, Federal
Communications Commission 2
N
New Zealand modem statement
16
notices
airline travel 10
battery 10, 18, 25
Brazil 4
Canada 4
Canadian French 4
environmental 21
equipment disposal 21
ergonomics 6
European Union 4
Federal Communications
Commission 2
headset and earphone volume
level 19
Japan 7
Japan power cord 17
keyboard 19
laser safety 11
Macrovision Corporation 17
mercury disposal 25
Mexico 8
modem 11
perchlorate material 25
power cords 17, 19
Singapore 8
South Korea 8
Taiwan 9
Thailand WWAN wireless
notice 9
travel 19
Vietnam compliance marking
9
P
power cord notice 17, 19
R
recycling, electronic hardware and
battery 21
S
Singapore wireless notice 8
26 Index