Broadcom BRCM1062 802.11a/b/g/n WLAN + Bluetooth PCI-E Combo Card User Manual installation guide

Download:
Mirror Download [FCC.gov]
Document ID	1820966
Application ID	stDhw8t1KfgQEGBypEOm5A==
Document Description	installation guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	31.84kB (398022 bits)
Date Submitted	2012-10-23 00:00:00
Date Available	2013-04-21 00:00:00
Creation Date	2012-07-27 17:46:44
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2012-07-27 17:46:44
Document Title	Microsoft Word - BRCM OEM installation Guide BCM94331CSAX A1 (3).docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	29432

BROADCOM C
CORPORATIION
19
90 Mathilda P
Place
Phon
ne: 408-543-3
3300
Fa
ax: 408-543-3
3399
Moodule In
nstallattion Insstructioons
An
nd
Reggulatorry Approval C
Conditiion
802.11 a/b//g/n 3x33 MIM
MO Mod
dule
Model N
No: BCM
M943331CSAX
FCC ID
D: QDS
S-BRCM
M1062
IC: 4324A-B
BRCM
M1062
Datte: Junee 26, 20012
Revission: A
A1
A. Conditions on using BRCM regulatory approvals:
1. Antennas must be installed to provide 20 cm separation distance from the transmitting antenna to
the body of user during normal operating condition AND only those antennas filed under FCC ID:
QDS-BRCM1062 with same type and lesser gain can be used with this device.
I.
Approved Antenna Type and Antenna Gain:
FCC ID: QDS‐BRCM1062
IC: 4324A‐BRCM1062
Freq [GHz]
2.4 – 2.484
5.15 – 5.25
5.25 – 5.35
5.50 – 5.70
5.725 – 5.85
613‐0131 Wi‐Fi1
613‐0131 Wi‐Fi2
Peak Gain (includes
cable loss)
Peak Gain (includes
cable loss)
613‐0131 Wi‐Fi3 &
Bluetooth
Peak Gain (includes
cable loss)
2.47
4.18
3.35
3.32
3.56
2.64
4.22
3.44
2.41
3.68
4.82
4.63
3.01
4.63
4.31
2. When the Module is installed in a netbook/notebook/laptop/tablet PC where the antenna location is
less than 20 cm separation distance to the body of the user, additional equipment authorization is
required except the conditions evaluated for the specific host (MacBook Pro Model A1425) listed
below :
I.
Antenna must be installed at the position to provide at least 7 mm to the body of user.
Antenna-to-user distance is measured by positioning display screen open 90 degree to
the keyboard. For antenna is not embedded in the display section, the distance is
measured between the nearest point between antenna to the edge/surface of device;
and
II.
Antenna-to-Antenna separation distance shall be greater than 5 cm between each of
transmitting antenna; and
III.
Antenna structures must be similar to the one documented in FCC filing. Variation on
the antenna structure may contribute difference SAR readings even if antenna is the
same type. It the antenna(s) used is different than the ones in FCC filing; it is
required for host integrator to consult with Broadcom in determining applicability of
approval condition.
3. The regulatory label on the final system must include the statement:“Contains FCC ID:
QDS-BRCM1062”or using electronic labeling method as documented in KDB 784748.
4. The final system integrator must ensure there is no instruction provided in the user manual or
customer documentation indicating how to install or remove the transmitter module except such
device has implemented two-ways authentication between module and the host system.
5. Simultaneous Transmission Requirements
I.
When multiple transmitters and antennas transmit simultaneously in a
laptop/notebook/netbook /tablet, the following may be used to determine simultaneous
transmission SAR evaluation reduction or exclusion requirements.
(i) Identify all possible combinations of simultaneous transmission configurations for all
transmitters and antennas installed in the display screen and keyboard of the intended
host computer configurations
(ii) Drawings showing antenna locations and separation distances between each of
simultaneous transmitting antenna(s) and antenna-to-user.
(iii) FCC ID of all transmitters, maximum average conducted output power in each
transmission mode and frequency band, operating configurations and exposure
conditions approved for the individual transmitters.
(iv) The type and physical dimensions of antennas incorporated in the intended host
configurations
(v) Antenna gain specified by the antenna manufacturer for antennas qualified for mobile
exposure conditions
(vi) other relevant information and restrictions required by the equipment certifications of
individual transmitters, including antenna changes
For each simultaneous transmission configuration identified in 5.I, if the conditions in a) or b) below
are satisfied and fully documented in the SAR report or Class I permissive change documentation,
simultaneous transmission SAR evaluation is not required for that configuration
a) When the [(Σ of the highest measured 1-g SAR for each portable transmitter/antenna included
in the simultaneous transmission configuration) / 1.6 W/kg] + Σ of [(the highest MPE for each
mobile transmitter/antenna included in the simultaneous transmission configuration) / (the
corresponding MPE limit)] < 1; or
b) For antennas included in the simultaneous transmission configuration that require SAR
evaluation, when the separation distance between each antenna pair is greater than 5 · [(SAR1 +
SAR2) / 1.6]1.5 cm, rounded to the nearest cm, and the Σ of [(the highest MPE for each mobile
transmitter/antenna included in the simultaneous transmission configuration) / (the
corresponding MPE limit)] < 1
Where: Σ in a) excludes antennas that do not require SAR evaluation, and MPE does not apply to
displays < 10” diagonal for both a) and b)
(Above simultaneous assessment guideline can be found at FCC web site under KDB 616217.
https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=33240
6. If simultaneous transmission condition does not meet requirements described above, please contact
Broadcom who is responsible for product compliance to determine the applicable simultaneous
transmission SAR evaluation procedures and applicable equipment authorization procedure. Module
must be installed and used in strict accordance with the manufacturer’s instructions as described in
the user documentation that comes with the product.
B. Regulatory Compliance Statement in the User Manual
A user’s manual or instruction manual must be included with the customer product that contains the
text as required by applicable law. Without limitation of the foregoing, an example (for illustration
purposes only) of possible text to include is set forth below:
a.
FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by tuning
the equipment off and on, the user is encouraged to try and correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the receiver
is connected. -Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
CAUTION: (this only applicable to 5GHz device) this device is restricted to indoor use due to
its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used
indoors for frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to
co-channel Mobile Satellite systems. High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with
and/or damage this device.
bb. Canad
da - Industry Canad
da (IC)
Operation iss subject too the follow
wing two coonditions: (1) this deviice may nott cause inteerference,
aand (2) this device muust accept anny interfereence, includding interfeerence that may causee undesired
ooperation off this devicce.” L ‘ utiliisation de cce dispositiif est autoriisée seulem
ment aux connditions
suivantes : ((1) il ne doit pas produuire de brouuillage et (2) l’ utilisaateur du disspositif doitt étre prêt à
aaccepter touut brouillagge radioélecctrique reçuu, même si ce brouillage est susceptible de
ccomprometttre le fonctiionnement du disposittif.
To reduce ppotential raddio interferrence to othher users, thhe antenna type and its gain shouuld be so
cchosen that the equivalent isotroppically radiated powerr (EIRP) is not more thhan that reqquired for
successful ccommunicaation.
This device has been ddesigned to operate wiith a 802.111abgn antennna, havingg a maximuum gain of
44.97dBi/2.44GHz and 66.56dBi/5G
GHz. Differeent types off antennas or the samee type of anntenna
hhaving a gaiin greater tthan 4.97dB
Bi/2.4GHz and 6.56dB
Bi/5GHz arre strictly prohibited fo
for use withh
thhis device. The requirred antennaa impedance is 50ohm
ms.
Caution: (tthis only ap
pplicable tto UNII devvice)
(ii) the devicce for operaation in the band 51500-5250 MH
Hz is only foor indoor use to reducce the
ppotential forr harmful innterferencee to co-channnel mobilee satellite systems;
(iii) the maximum antennna gain peermitted for devices inn the bandss 5250-53500 MHz andd 5470-5725
MHz shall ccomply witth the e.i.r.pp. limit; andd
(iiii) the maxximum anteenna gain ppermitted foor devices iin the bandd 5725-58255 MHz shalll comply
with the e.i..r.p. limits sspecified foor point-to--point and nnon point-tto-point opeeration as aappropriate.
High powerr radars are allocated aas primary users of thee 5.25 to 5..35 GHz annd 5.65 to
55.85 GHz bands. These radar stattions can caause interfeerence withh and/or dam
mage this ddevice.
Caution: Exposure too Radio Frrequency R
Radiation.
To comply w
with RSS 1102 RF expposure comppliance reqquirements,, for mobilee configuraations, a
separation ddistance of at least 20 cm must be maintaineed betweenn the antennna of this deevice and
aall persons. This devicce must not be co-locaated or operrating in coonjunction w
with any otther
aantenna or ttransmitter..
cc.
Europee - EU Resttrictions
This equipm
ment needs to be markked with thee
21155
symbool and can bbe used throoughout thee Europeann communitty.
indiccates that ussage restricctions applyy. Marking by the sym
mbol
Innformationn to be suppplied to the users:
8802.11a Resstrictions:
.
This product is for indoor use only when using channels 36, 40, 44, 48, 52, 56, 60, or 64
(5150– 5350 MHz).
DFS and TPC must remain enabled to ensure product compliance with EC regulations.
To ensure compliance with local regulations, be sure to select the country in which the access
point is installed.
This product can be used as shown in the table below:
Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance
requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained
between the antenna of this device and all persons.
Czech:
User's Manual in Czech language and a statement of conformity with Directive 1999/5/EC in
Czech language must be enclosed to each product.
5 GHz wireless LAN IEEE
802.11a
Indoor Use Only
A, AND, B, CH, D, CY, CZ, DK,
ES, EST, F, FIN, FL, FR, GB,
GR, H, I, IRL, IS, L, LT, M, MC,
N, NL, P, PL, RSM, S, SK,
SLO, V
France:
2.4GHz for Metropolitan France: In all Metropolitan départements, wireless LAN frequencies
can be used under the following conditions, either for public or private use:
· Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz
frequency band
· Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and
with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band
Note for system integrators:
- The module is tested to comply with the requirement of the R&TTE Directive. System
integrators are responsible for compliance of the final device with the R&TTE Directive.
- Packaging: CE Marking must also be on the outer packaging of the product. The outer
packaging must also provide an indication as to where the device is intended to be used and
OR conversely, where there may be restrictions for use.
d. Taiwan - NCC Statement to be included in the user guide
Statement- For general products
低功率電波輻性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、
商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電
信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Additional Statement - For 5G Band products
在5.25G ~5.35G頻帶內操作之無線資訊傳輸設備僅適於室內使用
Translation:
Article 12 Without permission, any company, firm or user shall not alter the frequency, increase
the power, or change the characteristics and functions of the original design of the certified lower
power frequency electric machinery. Article 14 The application of low power frequency electric
machineries shall not affect the navigation safety nor interfere a legal communication, if an
interference is found, the service will be suspended until improvement is made and the interference
no longer exists.
The forregoing legaal communnication refe
fers to the w
wireless teleecommuniccation operrated
according to the teelecommunnications law
ws and regulations. The low pow
wer frequenncy electricc
machinnery should be able to tolerate thee interferennce of the ellectric wavve radiationn electric
machinneries and equipment ffor legal coommunicatiions or induustrial and sscientific aapplicationss.
Radio ddevices usinng 5.25-5.335GHz bandds are restrricted to inddoor use onnly.
Appenddix:
認證合格標簽
簽 (ID):
模組認
“
CCXXxxxLPyyyZz＂
＂
使用本模組之
之平台,無法在外部看
看見審驗合
合格標籤時
時,應在該 平
平台的外部
部
如果使
明顯標
標示
“內含射
射頻模組
CCXXxxL
LPyyyZz” .
ee.
Korea
Innclude the following sstatement eeither on thhe label or inn the User Guide.
"당해 무선
선설비가 전
전파혼신 가
가능성이 있으므로 인명안전과 관련된
된 서비스는
는 할 수
없
없음"
ff.
Argenttina
The current approval is in the nam
me of Broaadcom’s loccal represenntative. It m
may be neceessary to
oobtain regullatory approoval in the name of thhe local disttributor or importer. W
We suggestt
manufactureers check w
with their loocal distribuutors and im
mporters inn Argentinaa.
gg. Brazil - Anatel
Before using Broadcom
m Anatel appprovals,
1 PC- OEM must make arrangement for its local offices or distributors to provide maintenance,
technical assistance or replace any faulty products sold in Brazil.
2 All warranty services will be provided by the distributors or PC-OEM sales support in Brazil.
An official agreement stating warranty responsibilities must be signed and made available to
Broadcom.
Interference statement to be included in the Users Guide
"Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência
a sistemas operando em caráter primário."
Translation: "This equipment operates in secondary character. It can be affected by harmful
interference. However, it cannot cause interference to systems operating in primary character."
h. South Africa – ICASA
PC-OEMs must make arrangement for importers to supply spare parts and carry out repairs in
South Africa.
i.
9. Indonesia - POSTEL
PC-OEMs must make arrangement for importers to provide product warranty and after sales
services.
j.
10. Japan – MIC
Radio devices using 5.15-5.35GHz bands are restricted to indoor use only.
k. 11. Mexico
PC-OEMs must make arrangement for importers to provide User Manual in Spanish in Mexico.
The User Manual must feature the following mandatory statement:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia prejudicial y (2)
este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que
pueda causar su operación no deseada.”
Translation:
The operation of this device is subject to the following two conditions:
(1) this equipment or device must not cause harmful interference and
(2) this equipment or device must accept any interference, including interference which could
otherwise cause its undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 29432
Create Date                     : 2012:07:27 17:46:44-07:00
Modify Date                     : 2012:07:27 17:46:44-07:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - BRCM OEM installation Guide BCM94331CSAX A1 (3).docx
Creator                         : 29432
Document ID                     : uuid:18021af0-5923-48ed-b9ef-7db39ac222ed
Instance ID                     : uuid:deedfdd9-c98f-4481-88ec-9b3f6f3f2f0b
Page Count                      : 10

EXIF Metadata provided by EXIF.tools