Browning A5 Shotgun Owners Manual
2015-09-10
: Browning Browning-A5-Shotgun-Owners-Manual-803696 browning-a5-shotgun-owners-manual-803696 browning pdf
Open the PDF directly: View PDF 
.
Page Count: 29
A5™
autoloading shotgun
owner’s manual
1
C O N T E N T S P A G E
State Warning ...........................................................................................2
WARNING: You are Responsible for Firearms Safety ...........................2
General Description and Operation .......................................................9
Nomenclature .........................................................................................10
Serial Number ........................................................................................10
Initial Cleaning .......................................................................................10
Operation of the “Safety” ......................................................................11
Bolt Latch ...............................................................................................13
Assembly .................................................................................................13
Disassembly ............................................................................................15
Ammunition ...........................................................................................16
Magazine Capacity .................................................................................17
Three-Shot Adapter (Plug) ....................................................................18
Loading ...................................................................................................20
Firing ......................................................................................................23
Unloading ...............................................................................................24
Interchangeable Choke Tube System ....................................................26
Adjusting Length of Pull........................................................................31
Adjusting Cast and Drop at Comb .......................................................32
Extra Barrels ...........................................................................................35
Cleaning and Maintenance Suggestions ...............................................36
Removal of the Trigger Group ..............................................................39
Removal of the Slide Assembly .............................................................41
Lubricating the Action Tube and Spring ..............................................47
Maintenance of Oil Finish Stocks .........................................................49
Models with Special Finishes ................................................................49
Service or Repair ....................................................................................50
Important operating instructions for:
BROWNING A5™
AUTOLOADING SHOTGUNS
If you have any questions about your new firearm, this
owner’s manual or other Browning products, contact:
Browning Customer Service
One Browning Place
Morgan, UT 84050-9326
Phone: (800) 333-3288
browning.com
Please use the space below to record information about
your new firearm.
Model __________________________________________________
Serial Number ____________________________________________
Purchased From __________________________________________
Date of Purchase __________________________________________
THANK YOU FOR CHOOSING A
BROWNING A5 SHOTGUN.
The A5 shotgun represents the most advanced recoil-operated
technology available in autoloading shotguns. A5 shotguns combine
the best of traditional Browning craftsmanship with state-of-the-art
design and manufacturing. Every detail of the A5 shotgun is
engineered to provide you the best in reliable operation and handling.
With a reasonable amount of care, your A5 shotgun is designed
to give you many years of dependable, enjoyable service.
2 3
Please read and understand all of the cautions, warnings, notices,
proper handling procedures and instructions outlined in this owner’s
manual before using your new firearm.
1 ALWAYS KEEP THE MUZZLE OF YOUR FiREARM POiNTED iN A SAFE
DiRECTiON EvEN THOUgH YOU ARE CERTAiN iT iS UNLOADED.
Never point any firearm at anything you do not intend to shoot.
Be extremely alert and aware of all persons and property within
the range of your ammunition.
2 NEvER RELY TOTALLY ON YOUR FiREARM’S MECHANiCAL “SAFETY”
DEviCE. LiKE ANY MECHANiCAL DEviCE, A “SAFETY” CAN SOMETiMES
FAiL; iT CAN bE jARRED OR iNADvERTENTLY MANiPULATED iNTO AN
UNSAFE CONDiTiON.
The word “safety” describes a firearm’s trigger block mechanism,
sear block mechanism, hammer block mechanism or firing pin
block mechanism. Mechanical “safeties” are designed to place your
firearm in a safer status, and no guarantee can be made that the
firearm will not fire even if the “safety” is in the on safe position.
Mechanical “safeties” merely aid safe gun handling and are no
excuse for pointing your firearm’s muzzle in an unsafe direction.
See “Operation of the Safety” on page 11 for instructions on the
operation of this firearm’s “safety.”
Remember, safe gun handling does not stop with your firearm’s
mechanical “safety” devices, it starts there. Always treat this firearm
with the respect due a loaded, ready-to-fire firearm.
Some firearms do not have a mechanical “safety.” Many target
firearms, lever-action firearms and pistols do not have manual
“safety” mechanisms. Therefore it is critical to read and
understand the owner’s manual for every firearm which explains
the safe operation of the firearm.
While it is a good idea to test your firearm’s mechanical “safety”
periodically for proper function, never test the “safety” while your
firearm is loaded or pointed in an unsafe direction.
STATE WARNING
According to state law, California requires that firearm manufacturers,
distributors and retailers include conspicuous, specific warnings with
firearms sold in that state.
WARNING: YOU ARE RESPONSIBLE
FOR FIREARMS SAFETY
FAiLURE TO FOLLOW ANY OF THE FOLLOWiNg WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
As a gun owner, you accept a set of demanding responsibilities. How
seriously you take these responsibilities can be the difference between
life and death.
There is no excuse for careless or abusive handling of any firearm.
At all times handle this firearm and all other firearms with intense
respect for their power and potential danger.
4 5
7 HUNTiNg FROM ELEvATED SURFACES SUCH AS TREESTANDS
iS DANgEROUS.
Doing so may increase the risk of mishandling a firearm. The
following rules should always be observed by you and those you
hunt with. Always make certain that the stand being used is safe
and stable. Always make certain that your firearm is unloaded
when it is being taken up and down from the stand. Always make
certain that your firearm is not dropped from the stand, or
dropped while it is being taken up or down from the stand.
Remember, a loaded firearm may discharge when dropped, even
with the “safety” in the on safe position.
8 STORE YOUR FiREARM AND AMMUNiTiON SEPARATELY, WELL bEYOND
THE REACH OF CHiLDREN.
Take prudent safeguards to ensure your firearm does not become
available to untrained, inexperienced or unwelcome hands. Store
all firearms in secure, locked cases or a gun safe. Keep your firearm
unloaded when not in use.
9 bEWARE OF bARREL ObSTRUCTiONS.
Mud, snow and an infinite variety of other objects may
inadvertently lodge in a barrel bore. It only takes a small
obstruction to cause dangerously increased pressures that
can damage your firearm and cause serious injury to yourself
and others.
bEFORE CHECKiNg FOR A bARREL ObSTRUCTiON, bE CERTAiN
YOUR FiREARM iS COMPLETELY UNLOADED, THERE iS NOT A
LivE SHELL iN THE CHAMbER AND THE “SAFETY” iS iN THE
ON SAFE POSiTiON.
After assuring yourself that the firearm is completely unloaded,
open the breech or action and look through the barrel to be sure it
is clear of obstructions. If an obstruction is seen, no matter how
small it may be, clean the bore with a cleaning rod and patch as
described on pages 37-38 of this owner’s manual.
3 WHENEvER YOU HANDLE ANY FiREARM, OR HAND iT TO SOMEONE,
ALWAYS OPEN THE ACTiON iMMEDiATELY AND viSUALLY CHECK THE
FiREARM’S CHAMbER TO MAKE CERTAiN THAT THE FiREARM iS
COMPLETELY UNLOADED.
Make certain the firearm does not inadvertently contain any
ammunition. Remember, merely removing the magazine does
not mean the chamber is unloaded. Always keep the chamber
empty and the “safety” in the on safe position unless shooting
is imminent.
4 ALWAYS WEAR EAR AND EYE PROTECTiON WHEN SHOOTiNg.
Unprotected, repeated exposure to gunfire can cause hearing
damage. Wear hearing protection (shooting ear plugs or muffs)
to guard against such damage.
Wear shooting glasses to protect your eyes from flying particles.
Allow proper distance (eye relief) between a scope and your
eye when firing a scoped rifle, shotgun or pistol. Do not use
unorthodox shooting methods that could cause the rearward travel
of the slide or bolt of a firearm to contact your eyes, face or hands.
Always keep a safe distance between the muzzle of your firearm
and any persons nearby, as muzzle blast, debris and ejecting shells
could inflict serious injury.
Always wear eye protection when disassembling and cleaning any
firearm to prevent the possibility of springs, spring-tensioned
parts, solvents or other agents from contacting your eyes.
5 KEEP ALL FiREARMS UNLOADED DURiNg TRANSPORT, EvEN
WHEN STORED iN A HOLSTER, gUN CASE, SCAbbARD OR
OTHER CONTAiNER.
6 DROPPiNg OR jARRiNg A LOADED FiREARM CAN CAUSE
ACCiDENTAL DiSCHARgE.
This can occur even with the “safety” in the on safe position. Be
extremely careful while hunting or during any shooting activity
to avoid dropping any firearm.
6 7
shells of nonstandard dimensions or which develop pressures
in excess of commercially available ammunition which has been
loaded in accordance with standards established by the Sporting
Arms and Ammunition Manufacturers’ Institute (SAAMI).
14 MAKE SURE OF ADEqUATE vENTiLATiON iN THE AREA THAT YOU
DiSCHARgE A FiREARM. LEAD ExPOSURE CAN OCCUR FROM
DiSCHARgiNg FiREARMS iN POORLY vENTiLATED AREAS, CLEANiNg
FiREARMS OR HANDLiNg AMMUNiTiON.
Lead is a substance that has been known to cause birth defects,
reproductive harm and other serious injury. Wash hands
thoroughly after exposure to ammunition or after cleaning
a firearm.
15 DO NOT SNAP THE FiRiNg PiN ON AN EMPTY CHAMbER; THE
CHAMbER MAY NOT bE EMPTY!
Treat every firearm with the respect due a loaded firearm, even
though you are certain the firearm is unloaded.
16 KEEP YOUR FiNgERS AWAY FROM THE TRiggER WHiLE LOADiNg
AND UNLOADiNg UNTiL SHOOTiNg iS iMMiNENT.
17 bE SURE OF YOUR TARgET AND bACKSTOP, PARTiCULARLY
DURiNg LOW LigHT PERiODS.
Know the range of your ammunition. Never shoot at water or
hard objects.
18 ALWAYS UNLOAD YOUR FiREARM’S CHAMbER bEFORE CROSSiNg
A FENCE, CLiMbiNg A TREE, jUMPiNg A DiTCH OR NEgOTiATiNg
OTHER ObSTACLES.
Never place your firearm on or against a fence, tree, car or other
similar object.
19 bE DEFENSivE AND ON gUARD AgAiNST UNSAFE gUN
HANDLiNg AROUND YOU AND OTHERS.
Don’t be timid when it comes to firearms safety. If you observe
other shooters violating any of these safety precautions, politely
suggest safer handling practices.
10 bE ALERT TO THE SigNS OF AMMUNiTiON MALFUNCTiON. iF YOU
DETECT AN OFF SOUND OR LigHT RECOiL WHEN A SHELL iS FiRED,
DO NOT LOAD ANOTHER SHELL iNTO THE CHAMbER.
If your firearm fails to fire, keep the muzzle pointed in a safe
direction for a minimum of 30 seconds. Rotate the ejection area of
the firearm away from you, carefully open the action and remove
the shell from the chamber. If the primer is indented, the defective
shell should be disposed of in a way that cannot cause harm. If the
primer is not indented, your firearm should be examined by a
qualified gunsmith and the cause of the malfunction corrected
before further use. Glance down the barrel to make sure that no
obstructions remain in the barrel. Completely clear the barrel
before loading and firing again. Failure to follow these instructions
can cause extensive damage to your firearm and possible serious
injury to yourself and others.
11 NEvER iNSERT A SHELL OF THE iNCORRECT gAUgE iNTO
ANY FiREARM.
The gauge of your firearm is marked on the barrel. Store all shells
of different gauges in completely separate and well-marked
containers. Never store shells of mixed gauges in a common
container or in your pockets. See pages 16-17 for more
information on the correct ammunition for your firearm.
12 ExAMiNE EvERY SHELL YOU PUT iN YOUR FiREARM.
We assume no responsibility for the use of unsafe or improper
firearm and ammunition combinations or damage or injury
caused by damaged ammunition. It is your responsibility
to read and heed all warnings in this owner’s manual and on
ammunition boxes. See pages 16-17 for more information on the
correct ammunition for your firearm.
13 USE ONLY SAAMi APPROvED AMMUNiTiON.
The barrel and action of this firearm have been made with
substantial safety margins beyond the pressures developed by
established American commercial loads. Nevertheless, we can
assume no liability for incidents which occur through the use of
8 9
25 WE RESERvE THE RigHT TO REFUSE SERviCE ON FiREARMS THAT
HAvE bEEN ALTERED, ADDED TO OR SUbSTANTiALLY CHANgED.
Removal of metal from the barrel, or modifications of the firing
mechanism and/or operating parts, may lead to a refusal of service
on such firearms. We will charge you for parts and labor to return
the firearm to original specifications.
DO NOT, UNDER ANY CiRCUMSTANCES, ALTER THE TRiggER, SAFETY
OR OTHER PARTS OF THE FiRiNg MECHANiSM OF THiS OR ANY
OTHER FiREARM. FAiLURE TO ObEY THiS WARNiNg MAY RESULT iN
iNjURY OR DEATH TO YOURSELF OR OTHERS.
BE CAREFUL!
GENERAL DESCRIPTION AND OPERATION
The Browning A5 is a recoil-operated autoloading shotgun capable of
quickly firing up to five shells (with the three-shot adapter removed,
using 2¾" loads), one shell at a time, with each successive pull of the
trigger. Upon firing, recoil acts upon the slide assembly and
compresses the recoil spring. When the energy from the recoil spring
is released, the energy causes the slide to travel rearward, unlocking
the bolt from the barrel and cycling the action. As the slide assembly
moves rearward, it cocks the hammer and ejects the fired shell. After
full rearward travel, the slide assembly returns forward, picks up a new
shell from the magazine and chambers it. After the last shell has been
fired, the slide assembly locks to the rear for faster reloading.
20 bE CERTAiN YOUR FiREARM iS UNLOADED bEFORE CLEANiNg.
Because so many firearm accidents occur when a firearm is being
cleaned, special and extreme care should be taken to be sure your
firearm is unloaded before disassembly, cleaning and reassembly.
Keep ammunition away from the cleaning location. Never test the
mechanical function of any firearm with live ammunition.
21 TEACH AND SUPERviSE FiREARMS SAFETY TO ALL MEMbERS OF
YOUR FAMiLY, ESPECiALLY TO CHiLDREN AND NON-SHOOTERS.
Closely supervise newcomers to the shooting sports. Encourage
enrollment in hunting and shooting safety courses.
22 NEvER DRiNK ALCOHOLiC bEvERAgES OR TAKE ANY TYPE
OF DRUgS bEFORE OR DURiNg SHOOTiNg.
Your vision, motor skills and judgment could be dangerously
impaired, making your gun handling unsafe to you and to others.
23 READ AND HEED ALL WARNiNgS iN THiS OWNER’S MANUAL, ON
AMMUNiTiON bOxES AND WiTH ALL ACCESSORiES THAT YOU iNSTALL
ON YOUR FiREARM.
It is your responsibility to secure the most up-to-date information
on the safe handling procedures of your Browning firearm. We
assume no liability for incidents which occur when unsafe or
improper firearm accessories or ammunition combinations
are used.
24 PRACTiCE PERiODiC MAiNTENANCE, AvOiD UNAUTHORiZED SERviCiNg.
Your firearm is a mechanical device which will not last forever,
and as such, is subject to wear and requires periodic inspection,
adjustment and service. Browning firearms should be serviced by
a Browning Recommended Service Facility or by our Service
Facility in Arnold, Missouri. We assume no responsibility for
injuries suffered or caused by unauthorized servicing, alterations
or modifications of Browning firearms.
FigURE 1
Buttstock
Trigger
Bolt
Latch
Forearm
Barrel
Muzzle
Rib
“Safety”
Bolt Release Button
Magazine Cap
Operating Handle
Recoil Pad
Front Sight
Receiver
10
NOMENCLATURE
In conventional firearm terminology the position and movement of
firearm parts are described as they occur with the firearm horizontal
and in the normal firing position: i.e., the muzzle is forward or in
front; the buttstock is rearward or to the rear; the trigger is downward
or underneath; the rib is upward or on top. For general parts
nomenclature, refer to Figure 1 on page 9. For specific parts names
related to disassembly, refer to Figure 2.
SERIAL NUMBER
The serial number of your A5 shotgun is found on the right side
of the receiver, below the bolt release button. Record this number
in the space provided at the front of this owner's manual for
future reference.
INITIAL CLEANING
NOTICE! PLEASE TAKE NOTE OF THE FOLLOWiNg iNFORMATiON bEFORE
CLEANiNg YOUR FiREARM.
CLEANING PARTS WITH SPECIAL FINISHES
Be especially careful when cleaning firearms with camouflage,
Dura-Touch® Armor Coating and other special finishes. Always
prevent these surfaces from coming in contact with cleaning solvents,
barrel scrubbers and other strong chemicals. It is preferable to clean
these surfaces with a lightweight gun oil containing no solvents, or
with a damp cloth and mild dish soap (be sure to keep water out of
the action). When cleaning your firearm’s bore and action, protect the
external finishes from any contact with chemicals used. Also, avoid
any contact between external finishes and other strong chemicals like
those found in DEET-containing insect repellents, sunscreens, etc.
Damage to camouflage, Dura-Touch and other finishes caused by
chemicals is irreversible and not repairable.
CLEANING
Various exposed metal parts of
your new firearm have been
coated at the factory with a rust
preventative compound. Before
assembling your shotgun, clean
the anti-rust compound from the
inside of the barrel, receiver and
the action/chamber areas. A high-
quality lightweight gun oil is ideal
for removing this compound, and
for giving your new firearm its
first lubrication. Place a drop of
lightweight gun oil on both sides of the inside of the receiver on the
rails on which the slide assembly moves (Figure 3). Clean the barrel
using a cleaning rod and patch as explained under “Cleaning the
Barrel” on page 37.
OPERATION OF THE “SAFETY”
ALWAYS KEEP THE “SAFETY” iN THE ON SAFE POSiTiON UNLESS
SHOOTiNg iS iMMiNENT. ALWAYS KEEP THE MUZZLE POiNTED iN A
SAFE DiRECTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD
RESULT iN SERiOUS iNjURY OR DEATH.
FigURE 3
Lightly lubricate the slide assembly rails inside
the receiver.
FigURE 2
Barrel Extension
Barrel Bracket
Buttstock
Operating Handle
Slide Assembly
Magazine Spring Retainer
Magazine Spring
Trigger Group
Forearm
Follower
Barrel
Magazine
Receiver
Three-Shot Adapter (Plug)
Trigger Group Pins
Recoil Pad
11
Magazine Cap
12
BOLT LATCH
The A5 shotgun features a bolt latch mounted just forward of the
trigger guard, on the bottom of the shotgun. The bolt latch performs
two functions:
• Allows the slide assembly to be locked in the open position when
the magazine is unloaded.
• Releases a shell from the magazine to be loaded into
the chamber.
The bolt latch must be slid rearward before pulling the operating
handle completely rearward in order to lock the slide assembly in the
open position or release a shell for the magazine to be chambered.
ASSEMBLY
ALWAYS KEEP THE MUZZLE POiNTED iN A SAFE DiRECTiON. bEFORE
STARTiNg ASSEMbLY PROCEDURES, viSUALLY iNSPECT THE CHAMbER
AND MAgAZiNE TO bE AbSOLUTELY CERTAiN THE FiREARM iS
COMPLETELY UNLOADED. PLACE THE “SAFETY” iN THE ON SAFE
POSiTiON. FAiLURE TO FOLLOW THiS WARNiNg COULD RESULT iN
SERiOUS iNjURY OR DEATH.
The A5 shotgun is delivered in the box with the barrel removed from
the receiver. Assemble the A5 according to the following procedures.
1 Lock the slide assembly rearward by first sliding the bolt latch to
the rear, then pulling the operating handle fully to the rear as
explained above.
NOTICE! NEvER ALLOW THE ACTiON TO SLAM CLOSED bY PRESSiNg THE
bOLT RELEASE bUTTON WiTHOUT THE bARREL iNSTALLED. iF THE SLiDE
ASSEMbLY iS RELEASED FORWARD WiTH THE bARREL REMOvED, THE
OPERATiNg HANDLE WiLL STRiKE THE RECEivER AND CAUSE DAMAgE.
2 Unscrew the magazine cap by turning the it counterclockwise.
3 Remove the forearm from the magazine tube.
The “safety” is designed to prevent the trigger from being pulled when
in the on safe position. The “safety” is located at the rear of the trigger
guard. In the off safe position, a red warning band is visible on the
safety button on the left side of the trigger guard.
To place the firearm on safe, press the “safety” button to the right
(Figure 4).
To move the “safety” to the off safe or fire position, press the safety
button to the left. This exposes the red warning band on the “safety”
button (Figure 5).
DO NOT DEPEND ON THE RED COLOR ALONE TO iNDiCATE YOUR
FiREARM’S SAFETY STATUS. TiME, ExPOSURE TO THE ELEMENTS, AND
THE AbRASivE ACTiON OF CLEANiNg AgENTS CAN ERASE iT. FAiLURE TO
FOLLOW THiS WARNiNg COULD RESULT iN SERiOUS iNjURY OR DEATH.
The “safety” can be reversed from right- to left-handed by a
qualified gunsmith. When installed, the left-handed “safety” will
have the “safety” button’s red warning band on the right side of
the trigger guard.
13
FigURE 4
The “safety” shown in the on safe position.
FigURE 5
The “safety” shown in the off safe position.
14 15
7 Continue to apply pressure on the barrel, pushing it into the
receiver, while installing the magazine cap by turning it clockwise
(Figure 10).
DISASSEMBLY
ALWAYS KEEP THE MUZZLE POiNTED iN A SAFE DiRECTiON. bEFORE
STARTiNg DiSASSEMbLY PROCEDURES, OPEN THE ACTiON AND viSUALLY
iNSPECT THE CHAMbER AND MAgAZiNE TO bE AbSOLUTELY CERTAiN THE
FiREARM iS COMPLETELY UNLOADED. PLACE THE “SAFETY” iN THE ON
SAFE POSiTiON. FAiLURE TO FOLLOW THiS WARNiNg COULD RESULT iN
SERiOUS iNjURY OR DEATH.
1 Lock the slide assembly rearward by first sliding the bolt latch to
the rear, then pulling the operating handle fully to the rear as
explained on page 13.
NOTICE! NEvER ALLOW THE ACTiON TO SLAM CLOSED bY PRESSiNg THE
bOLT RELEASE bUTTON WiTHOUT THE bARREL iNSTALLED. iF THE SLiDE
ASSEMbLY iS RELEASED FORWARD WiTH THE bARREL REMOvED, THE
OPERATiNg HANDLE WiLL STRiKE THE RECEivER AND CAUSE DAMAgE.
2 Unscrew the magazine cap by turning it counterclockwise.
NOTICE! DO NOT SqUEEZE HARD ON
THE OPEN REAR END OF A WOOD
FOREARM. TOO MUCH PRESSURE
COULD CAUSE THE WOOD TO SPLiT.
4 Remove the forearm retainer by
sliding it forward and out of the
forearm (Figure 6). Retain the
forearm retainer for future use
as it helps prevent damage to
the receiver and forearm when
the barrel is not installed on
the shotgun.
5 Angle the front of the forearm over the barrel bracket slightly, then
push the forearm completely onto the barrel bracket (Figure 7).
When the forearm is completely on the barrel bracket, press the
rear of the forearm into place on the barrel (Figure 8).
NOTICE! DO NOT SqUEEZE THE OPEN REAR END OF A WOOD FOREARM.
TOO MUCH PRESSURE COULD CAUSE THE WOOD TO SPLiT.
6 Slide the barrel and forearm over the magazine tube. Align the
barrel extension and forearm studs with the recesses in the front
of the receiver. The barrel extension should slip solidly into the
receiver (Figure 9).
FigURE 6
Before assembly, unscrew the magazine cap
and remove the forearm retainer.
FigURE 7
Angle the forearm onto the front of the barrel
bracket and push the forearm forward.
FigURE 9
Slide the barrel and forearm over the magazine
tube and insert the barrel extension into
the receiver.
FigURE 8
When the forearm is completely forward, snap
the rear of it into position on the barrel.
FigURE 10
Press and hold the barrel down and install the
magazine cap.
16 17
DO NOT PUT A 16 OR 20 gAUgE SHELL iN A 12 gAUgE SHOTgUN. DO
NOT PUT A 28 gAUgE SHELL iN A 20 gAUgE SHOTgUN. DO NOT PUT A
.410 bORE SHELL iN A 28 gAUgE SHOTgUN. NEvER PUT METALLiC
CARTRiDgES OF ANY KiND iN A SHOTgUN. SPECiFiCALLY, NEvER PUT
CENTERFiRE RiFLE OR PiSTOL CARTRiDgES iN A SHOTgUN CHAMbERED
FOR .410 bORE. FAiLURE TO FOLLOW THiS WARNiNg COULD RESULT iN
SERiOUS iNjURY OR DEATH.
NOTICE! USiNg iNCORRECT AMMUNiTiON MAY CAUSE YOUR FiREARM TO
MALFUNCTiON AND COULD SEvERELY DAMAgE YOUR FiREARM. ALWAYS
TAKE CARE TO USE THE CORRECT AMMUNiTiON iN YOUR FiREARM.
The most certain way to bulge or rupture a shotgun barrel is to load
a smaller gauge shell into a larger gauge chamber. The smaller gauge
shell will not fall completely through the barrel; its rim is caught by
the front of a larger gauge chamber or at the larger gauge’s choke.
Your shotgun will misfire (with the chamber appearing to be empty).
It is then possible to load the correct gauge shell behind the smaller
gauge shell. If the shotgun is then fired, the result will be a so-called
“12-16, 12-20, 20-28 or 28-.410 burst” which can cause extensive
damage to your shotgun and possible serious injury to you and others.
We can assume no responsibility for incidents which occur through
the use of shells of nonstandard dimension or those developing
pressures in excess of SAAMI (Sporting Arms and Ammunition
Manufacturers’ Institute) established standards.
A5 shotguns will shoot all 12 gauge, 2¾" and 3", 1 oz. and heavier
factory lead and steel field loads. However, due to variations in the
manufacture of ammunition, and to help ensure reliability, always use
ammunition that is powerful enough to cycle the action completely.
MAGAZINE CAPACITY
With the magazine three-shot adapter (plug) removed, A5 shotguns
will hold four 2¾" or three 3" shells in the magazine.
3 Remove the forearm and barrel together by pulling them forward
and off the magazine tube.
4 Remove the forearm from the barrel by carefully pulling the rear
of the forearm away from the barrel slightly, then pulling the
forearm to the rear and off the barrel bracket.
NOTICE! DO NOT SqUEEZE THE OPEN REAR END OF A WOOD FOREARM.
TOO MUCH PRESSURE COULD CAUSE THE WOOD TO SPLiT.
5 For cleaning, follow the guidelines in “Cleaning and Maintenance
Suggestions” beginning on page 36.
For storage, install the forearm retainer into the front of the
forearm. Slide the forearm over the magazine tube and install the
magazine cap. You will then have two compact units: the barrel,
and the action with stock and forearm.
NOTICE! AFTER THE bARREL HAS bEEN REMOvED, LEAvE THE SLiDE
ASSEMbLY iN THE REARWARD POSiTiON. DO NOT PRESS THE bOLT
RELEASE bUTTON. iF THE SLiDE ASSEMbLY iS RELEASED FORWARD WiTH
THE bARREL REMOvED, THE OPERATiNg HANDLE WiLL STRiKE THE
RECEivER, CAUSiNg DAMAgE.
AMMUNITION
USE ONLY SHELLS OF THE CORRECT gAUgE AND LENgTH. THE gAUgE
AND LENgTH OF THE CHAMbER iS iNSCRibED ON THE SiDE OF THE
bARREL. DO NOT USE AMMUNiTiON OTHER THAN WHAT iS iNSCRibED
ON THE SiDE OF THE bARREL. ExAMiNE EvERY SHELL YOU PUT iN YOUR
SHOTgUN. FAiLURE TO FOLLOW THiS WARNiNg COULD RESULT iN
SERiOUS iNjURY OR DEATH.
USE SHELLS OF THE CORRECT LENgTH. DO NOT USE 3" OR 3½" SHELLS
iN A bARREL WiTH A 2¾" CHAMbER, OR 3½" SHELLS iN A bARREL WiTH
A 3" CHAMbER.
DOiNg SO CAN RESULT iN A bUiLDUP OF DANgEROUSLY
HigH PRESSURES. FAiLURE TO FOLLOW THiS WARNiNg COULD RESULT
iN SERiOUS iNjURY OR DEATH.
18
3 The A5 features the unique TurnKey Magazine Plug which
is quickly and easily removed by inserting a key or standard
screwdriver into the slot in the end of the magazine tube.
To remove the three-shot adapter (plug), press inward and turn
the key or flat-blade screwdriver a quarter-turn to align the three-
shot adapter (plug) with the slot in the end of the magazine
(Figure 11). This unlocks the three-shot adapter (plug), allowing it
to be removed.
4 If the barrel and forearm are on the shotgun, hold them to prevent
them from falling out of the receiver while pointing the magazine
tube down to allow the three-shot adapter (plug) to fall out of the
end of the magazine tube. Grasp and remove it (Figure 12).
5 Reinstall the magazine cap as explained previously.
INSTALLING THE THREE-SHOT ADAPTER (PLUG)
If you need to install the magazine three-shot adapter (plug) to limit
the magazine to three shells, again perform the following operation:
1 Lock the slide assembly rearward by first sliding the bolt latch to
the rear, then pulling the operating handle fully to the rear as
explained on page 13. Ensure the firearm is completely unloaded
and the "safety" is in the on safe position.
THREE-SHOT ADAPTER (PLUG)
ALWAYS KEEP THE MUZZLE POiNTED iN A SAFE DiRECTiON. bEFORE
REMOviNg OR iNSTALLiNg THE THREE-SHOT ADAPTER (PLUg),
COMPLETELY UNLOAD THE SHOTgUN. OPEN THE ACTiON AND viSUALLY
iNSPECT THE CHAMbER, FEED MECHANiSM AND MAgAZiNE TO bE
AbSOLUTELY CERTAiN THE FiREARM iS COMPLETELY UNLOADED. PLACE
THE “SAFETY” iN THE ON SAFE POSiTiON. FAiLURE TO FOLLOW THiS
WARNiNg COULD RESULT iN SERiOUS iNjURY OR DEATH.
WEAR EYE PROTECTiON WHEN REMOviNg OR iNSTALLiNg THE
THREE-SHOT ADAPTER (PLUg) TO PREvENT SPRiNgS, SPRiNg-LOADED
PARTS, SOLvENTS OR OTHER AgENTS FROM CONTACTiNg YOUR
EYES, RESULTiNg iN iNjURY.
The A5 is delivered with the magazine three-shot adapter (plug)
installed in the magazine, limiting magazine capacity to two shells in
compliance with federal migratory bird regulations. If you do not
wish to be limited to three shots, when it is not required by law, you
can remove (or reinstall) the three-shot adapter (plug) as follows.
Note: The accompanying photos show the barrel removed for
clarity purposes. Removing the barrel is not necessary to remove
the three-shot adapter (plug).
REMOVING THE THREE-SHOT ADAPTER (PLUG)
1 Lock the slide assembly rearward by first sliding the bolt latch to
the rear, then pulling the operating handle fully to the rear as
explained on page 13. Ensure the firearm is completely unloaded
and the "safety" is in the on safe position.
NOTICE! NEvER ALLOW THE ACTiON TO SLAM CLOSED bY PRESSiNg THE
bOLT RELEASE bUTTON WiTHOUT THE bARREL iNSTALLED. iF THE SLiDE
ASSEMbLY iS RELEASED FORWARD WiTH THE bARREL REMOvED, THE
OPERATiNg HANDLE WiLL STRiKE THE RECEivER AND CAUSE DAMAgE.
2 Remove the magazine cap as explained previously.
19
FigURE 12
Remove the three-shot adapter (plug).
FigURE 11
Use a key or small screwdriver to press in
on the three-shot adapter (plug), then rotate
a quarter-turn.
20 21
SPEED LOADING
1 If shooting is imminent, lock
the slide assembly rearward by
first sliding the bolt latch to the
rear, then pulling the operating
handle fully to the rear as
explained on page 13. Ensure
the firearm is completely
unloaded and the "safety" is
in the on safe position.
2 Insert a shell into the magazine
(Figure 14). The shell will be
automatically cycled from the magazine to the chamber.
KEEP YOUR FiNgERS CLEAR OF THE EjECTiON PORT WHEN LOADiNg
THE SHOTgUN USiNg THE SPEED LOADiNg PROCEDURE. FAiLURE TO
FOLLOW THiS WARNiNg COULD RESULT iN iNjURY.
3 If desired, load the magazine to full capacity by inserting a shell of
proper gauge and length through the loading port at the bottom of
the receiver up into the magazine, using your thumb to position it
fully forward in the magazine tube. Make sure the rim of the shell
engages the shell stop and is held fully inside the magazine tube. It
will make an audible click when fully inserted.
THE SHOTgUN iS NOW READY TO FiRE bY SiMPLY MOviNg THE “SAFETY”
TO THE OFF SAFE POSiTiON AND PULLiNg THE TRiggER.
LOADING THE MAGAZINE
1 Lock the slide assembly rearward by first sliding the bolt latch to
the rear, then pulling the operating handle fully to the rear as
explained on page 13. Ensure the firearm is completely unloaded
and the "safety" is in the on safe position.
NOTICE! NEvER ALLOW THE ACTiON
TO SLAM CLOSED bY PRESSiNg THE
bOLT RELEASE bUTTON WiTHOUT THE
bARREL iNSTALLED. iF THE SLiDE
ASSEMbLY iS RELEASED FORWARD
WiTH THE bARREL REMOvED, THE
OPERATiNg HANDLE WiLL STRiKE THE
RECEivER AND CAUSE DAMAgE.
2 Remove the magazine cap as
explained previously.
3 Insert the magazine three-shot
adapter (plug) into the slot in
the end of the magazine tube.
4 Insert a key or flat-blade screwdriver into the slot in the end of the
magazine tube. Press inward and turn the three-shot adapter
(plug) a quarter-turn to secure the in the magazine (Figure 13).
5 Reinstall the magazine cap as explained previously.
LOADING
WHEN LOADiNg YOUR SHOTgUN ALWAYS KEEP THE MUZZLE POiNTED
iN A SAFE DiRECTiON, ALWAYS PLACE THE “SAFETY” iN THE ON SAFE
POSiTiON AND KEEP YOUR FiNgERS AWAY FROM THE TRiggER.
FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT iN SERiOUS
iNjURY OR DEATH.
DO NOT CARRY YOUR SHOTgUN WiTH A SHELL iN THE CHAMbER TO
AvOiD ACCiDENTAL DiSCHARgE. WHEN FiRiNg iS NO LONgER iMMiNENT,
MAKE SURE THE “SAFETY” iS iN THE ON SAFE POSiTiON AND UNLOAD
THE CHAMbER. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT iN
SERiOUS iNjURY OR DEATH.
TAKE CARE WHEN LOADiNg THE MAgAZiNE. THE EDgES OF THE CARRiER
ARE SHARP AND MAY CAUSE iNjURY TO FiNgERS OR DAMAgE gLOvES.
Insert the shell into the bottom of the receiver
and push it fully forward into the magazine.
FigURE 14
FigURE 13
The three-shot adapter (plug) shown secured in
the magazine tube.
22
3 If shooting is imminent, insert
a shell of the proper gauge and
length through the ejection
port into the open breech
(Figure 15).
4 Press the bolt release button
to deliver the shell into
the chamber.
KEEP YOUR FiNgERS CLEAR OF THE
EjECTiON PORT WHENEvER CLOSiNg
THE ACTiON WiTH THE bOLT RELEASE
bUTTON. FAiLURE TO FOLLOW THiS WARNiNg COULD RESULT iN iNjURY.
THE SHOTgUN iS NOW READY TO FiRE bY SiMPLY MOviNg THE “SAFETY”
TO THE OFF SAFE POSiTiON AND PULLiNg THE TRiggER.
5 With a shell in the chamber, you may load the magazine to full
capacity. To load the magazine, insert a shell of proper gauge and
length through the loading port at the bottom of the receiver up
into the magazine, using your thumb to position it fully forward in
the magazine tube. Make sure the rim of the shell engages the shell
stop and is held fully inside the magazine tube. It will make an
audible click when fully inserted.
FIRING
NEvER LOAD A SHELL iNTO THE CHAMbER OR PLACE THE “SAFETY” iN
THE OFF SAFE POSiTiON UNLESS SHOOTiNg iS iMMiNENT. ALWAYS KEEP
THE MUZZLE POiNTED iN A SAFE DiRECTiON. FAiLURE TO FOLLOW THESE
WARNiNgS COULD RESULT iN SERiOUS iNjURY OR DEATH.
1 Place the “safety” in the on safe position.
2 Load a shell into the chamber as explained previously.
2 Close the slide assembly by pressing the bolt release button.
3 Insert a shell of the proper gauge and length through the loading
port at the bottom of the receiver up into the magazine, using
your thumb to position it fully forward in the magazine tube
(Figure 14, page 21). Make certain the rim of the shell engages the
shell stop and is held fully inside the magazine tube. It will make
an audible click when fully inserted.
4 If desired, continue loading the magazine until it is full.
LOADING THE CHAMBER MANUALLY FROM THE MAGAZINE
1 With the slide assembly closed, depress the carrier with the front
of a shell and, using your thumb, push the shell into the magazine
until the shell is held in place by the shell stop.
2 If desired, continue to load the magazine, as explained previously.
3 If shooting is imminent, a shell can now be moved from the
magazine to the chamber by sliding the bolt latch to the rear to
release a shell from the magazine, pulling back fully on the
operating handle and releasing it, allowing it to move forward.
A shell will be fed automatically to the chamber as the slide
assembly closes. Another shell can then be inserted into the
magazine to load to full capacity.
THE SHOTgUN iS NOW READY TO FiRE bY SiMPLY MOviNg THE “SAFETY”
TO THE OFF SAFE POSiTiON AND PULLiNg THE TRiggER.
LOADING THE CHAMBER THROUGH THE EJECTION PORT
1 Lock the slide assembly rearward by first sliding the bolt latch to
the rear, then pulling the operating handle fully to the rear as
explained on page 13.
2 Visually inspect the chamber, feed mechanism and magazine to
make sure they are clear of any obstructions.
23
FigURE 15
Insert a shell through the ejection port into
the breech.
24 25
3 With a shell in the chamber, you need only move the “safety” to
the off safe position to fire the shotgun.
4 When ready to fire, move the “safety” into the off safe position,
take aim and squeeze the trigger.
After a shell is fired, energy from the fired shell operates the slide
assembly, ejects the fired shell, picks up a loaded shell from the
magazine and automatically chambers it. You may continue to fire the
shotgun until the magazine is empty by pulling the trigger to fire each
shell. After the last shell is fired, the breech of the shotgun remains
open, with the slide assembly locked to the rear. This allows
convenient and fast reloading.
If you are done shooting, leave the slide assembly locked to the rear,
with the breech in the open position so that you may visually inspect
the chamber, bore, carrier and magazine to be sure they contain
no shells.
AFTER FiRiNg, OR WHEN SHOOTiNg iS NO LONgER iMMiNENT,
iMMEDiATELY PLACE THE “SAFETY” iN THE ON SAFE POSiTiON.
FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT iN SERiOUS
iNjURY OR DEATH.
EvEN WiTH THE SLiDE ASSEMbLY LOCKED OPEN AFTER SHOOTiNg, DO
NOT ASSUME THE SHOTgUN iS UNLOADED. ALWAYS iNSPECT THE
CHAMbER, bARREL, FEED MECHANiSM AND MAgAZiNE TO bE CERTAiN
THE SHOTgUN iS COMPLETELY UNLOADED. FAiLURE TO FOLLOW THESE
WARNiNgS COULD RESULT iN SERiOUS iNjURY OR DEATH.
UNLOADING
WHEN UNLOADiNg YOUR SHOTgUN ALWAYS PLACE THE “SAFETY” iN THE
ON SAFE POSiTiON. KEEP THE MUZZLE POiNTED iN A SAFE DiRECTiON
AND YOUR FiNgERS AWAY FROM THE TRiggER. FAiLURE TO FOLLOW
THESE WARNiNgS COULD RESULT iN SERiOUS iNjURY OR DEATH.
ALWAYS iNSPECT THE CHAMbER, bARREL, FEED MECHANiSM AND
MAgAZiNE CAREFULLY AFTER UNLOADiNg TO bE SURE ALL LivE SHELLS
ARE CLEARED FROM THE FiREARM.
SPEED UNLOADING
1 Place the “safety” in the on safe position.
2 Pull rearward on the operating handle to eject the shell from
the chamber. Allow the bolt to close on the empty chamber.
3 Turn the shotgun over so the trigger guard is facing up, then push
the carrier down with your finger as far as it will go.
4 Shells are retained in the magazine by the shell stop, which catches
the rim of the shell base. Locate the shell stop inside the receiver
(Figure 16) on the right side of the loading port (visually to the left
side when looking down into the loading port).
5 Push in on the shell stop to release a shell from the magazine.
When the shell stop is pressed, a shell is forced out of the magazine
under spring pressure. Catch the shell as it comes out.
6 Press the stop again to release the next shell. Continue to do this
until the magazine is empty. Be careful not to pinch your finger
on the carrier.
7 Using your finger, feel the opening of the magazine to make sure
there are no shells that have not been fed from the magazine and
ejected. Visually inspect the
chamber, feed mechanism and
magazine to assure there are no
shells remaining.
8 Lock the slide assembly rearward
by first sliding the bolt latch to
the rear, then pulling the
operating handle fully to the rear
as explained on page 13. Ensure
the firearm is completely
unloaded and the "safety" is
in the on safe position.
FigURE 16
Push inward on the shell stop to unload
the magazine.
27
DO NOT USE ANY OTHER CHOKiNg DEviCE iN ANY SHOTgUN bARREL
SUPPLiED bY bROWNiNg.
USE ONLY THE APPROPRiATE gAUgE OF iNvECTOR-DS CHOKE TUbE iN
THiS SHOTgUN. DO NOT FiRE THiS SHOTgUN WiTHOUT THE CORRECT
CHOKE TUbE iNSTALLED. DAMAgE MAY RESULT TO THE THREADS iNSiDE
THE bARREL.
FAiLURE TO FOLLOW THiS iNFORMATiON COULD RESULT iN DAMAgE
YOUR SHOTgUN OR POSSibLE iNjURY.
NOTICE! USE ONLY THE iNvECTOR-DS CHOKE TUbE T-WRENCH SUPPLiED
WiTH YOUR SHOTgUN TO iNSTALL AND REMOvE iNvECTOR-DS CHOKE
TUbES. USiNg ANY OTHER WRENCH MAY DAMAgE THE THREADS iN
THE bARREL.
Current production A5 shotgun barrels are threaded to accept the
Invector-DS choke system. Confirm the choke system of your shotgun
by looking on the right side of the barrel where the specifications are
inscribed, Invector choke tubes are identified in Figure 17 (flush mount
tubes are shown).
The constriction of each choke tube is indicated twice on the choke
tube: on the side of the tube, and indicated with a “notch” code on the
top rim of the tube. The included choke tube T-Wrench is used to
remove and install choke tubes.
Some target shotguns include
premium extended choke tubes.
The constriction of premium
choke tubes is indicated twice on
the choke tube: on the side of the
tube, and indicated with an
abbreviation in the colored band.
The constriction of flush fit choke
tubes is indicated twice on the
choke tube: on the side of the tube,
and indicated with a “notch” code
on the top rim of the tube. The
UNLOADING BY CYCLING THE ACTION
1 With the “safety” in the on safe position, slide the bolt latch to the
rear, grasp the operating handle and cycle the action. Repeat sliding
the bolt latch to the rear and pulling the operating handle rearward
until all shells are transferred from the magazine to the chamber
and then ejected. Lock the bolt assembly in the rearward, open
position as explained previously. Take care to avoid letting shells fall
to the ground.
2 After the last shell in the magazine has been cycled through the
chamber and out the ejection port, use your index finger to feel the
opening of the magazine to make sure there are no shells that have
not been fed from the magazine and ejected. Visually inspect the
chamber, feed mechanism and magazine to assure there are no
shells remaining.
INTERCHANGEABLE CHOKE TUBE SYSTEM
NEvER ATTEMPT TO REMOvE OR iNSTALL A CHOKE TUbE iN A LOADED
FiREARM. WHENEvER REMOviNg OR iNSTALLiNg A CHOKE TUbE iN A
SHOTgUN ALWAYS KEEP THE MUZZLE POiNTED iN A SAFE DiRECTiON.
OPEN THE ACTiON AND MAKE AbSOLUTELY CERTAiN THE SHOTgUN iS
COMPLETELY UNLOADED, ALWAYS PLACE THE “SAFETY” iN THE ON SAFE
POSiTiON AND KEEP YOUR FiNgERS AWAY FROM THE TRiggER. FAiLURE
TO FOLLOW THESE WARNiNgS COULD RESULT iN SERiOUS iNjURY
OR DEATH.
bROWNiNg iNvECTOR-DS CHOKE TUbES ARE FOR USE ONLY iN
bROWNiNg SHOTgUNS WiTH bACK-bORED bARRELS, AND ARE NOT
iNTERCHANgEAbLE WiTH bROWNiNg STANDARD iNvECTOR OR iNvECTOR-
PLUS CHOKE TUbES. DO NOT USE iNvECTOR-DS TUbES iN bARRELS
THREADED FOR iNvECTOR-PLUS OR STANDARD iNvECTOR TUbES. DO NOT
USE bROWNiNg iNvECTOR-DS, STANDARD iNvECTOR OR iNvECTOR-PLUS
CHOKE TUbES iN ANY SHOTgUN bARRELS NOT SUPPLiED bY bROWNiNg.
26
FigURE 17
Left: Invector-DS
Center: Invector-Plus
Right: Standard Invector
28 29
included choke tube T-Wrench is used to remove and install
choke tubes.
Invector choke tubes are compatible with factory ammunition that has
been loaded in compliance with SAAMI specifications, including
magnum lead and steel shot loads, sabots and shotgun slug loads.
Replacement and additional tubes and wrenches are available from
your Browning dealer, or by contacting our Consumer Department.
See “Service or Repair” on page 49 for contact information.
CHOKE TUBE SELECTION
To help you choose the correct choke tube for each hunting and
shooting situation, all Browning Invector choke tubes are inscribed
on the side with the patterns they produce with both lead and steel
shot. Each Invector tube also has notches in the top rim of the tube
(Figure 18, page 29). These notches are a code to identify the choke
designation while the tube is installed. Rim notches refer specifically to
lead shot. Use the chart on page 29 to cross-reference from lead to steel,
and determine the appropriate tubes for your ammunition and
hunting/shooting situation.
Several choke tubes are supplied with your shotgun. The choke tubes
listed are also available as accessories. Remember, Standard Invector,
Invector-Plus and Invector-DS tubes are not interchangeable.
Invector-Plus and Invector-DS tubes are for Browning shotguns
with back-bored barrels only. Before removing or installing tubes, or
reading the rim notch code, make sure the shotgun is fully unloaded.
CHOKE TUBE REMOVAL
1 Place the “safety” in the on safe position. Always make sure the
shotgun is completely unloaded. Keep the muzzle pointed in a
safe direction.
2 Use the choke tube T-Wrench to loosen the tube, turning it
counterclockwise (Figure 19, page 30). Finger-twist the tube
the rest of the way out of the barrel.
FigURE 18
NO NOTCHES
THREE NOTCHES
FIVE NOTCHES
TWO NOTCHES
FOUR X FOUR
NOTCHES
ONE NOTCH
RIM
NOTCHES
PATTERN WITH
LEAD SHOT
PATTERN WITH
STEEL SHOT
i FULL *
ii x ii LigHT FULL ExTRA FULL**
ii iMP. MODiFiED FULL**
iii MODiFiED iMP. MODiFiED**
iiii x iiii LigHT MODiFiED iMP. MODiFiED
iiii iMP. CYLiNDER MODiFiED
iiiii SKEET iMP. CYLiNDER
NO NOTCHES CYLiNDER CYLiNDER
* Not for use with steel shot. Using an over-tight choke constriction with
steel shot will result in an ineffective “blown” pattern.
**
When more than one choke designation is listed for a given steel shot
pattern, use the more open choke listed for high velocity, larger shot size
steel loads.
TWO X TWO
NOTCHES
FOUR NOTCHES
30 31
ADJUSTING LENGTH OF PULL
The buttstock can be adjusted for length of pull by adding or
removing spacers (available separately) to the rear of the stock. One
¼" and one ½" thick spacers are included with the A5 (Figure 20,
page 30). A maximum of ¾" of spacers can be added with the screws
provided to extend length of pull. With longer screws (not provided),
more than ¾" can be added to extend length of pull.
Spacers can be ordered through your Browning dealer or by calling
our Customer Service Department at (800) 322-4626.
bEFORE PERFORMiNg ADjUSTMENT PROCEDURES, PLACE THE “SAFETY”
iN THE ON SAFE POSiTiON. OPEN THE ACTiON AND MAKE CERTAiN YOUR
SHOTgUN iS COMPLETELY UNLOADED. KEEP THE MUZZLE POiNTED iN A
SAFE DiRECTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
INSTALLING A SPACER
IMPORTANT: Before loosening the buttstock to install spacers, the
trigger group should be in position in the receiver. This aligns the
buttstock and makes assembly easier.
NOTICE! USE ONLY THE iNvECTOR-DS
T-WRENCH SUPPLiED WiTH YOUR
SHOTgUN TO iNSTALL AND REMOvE
iNvECTOR-DS CHOKE TUbES. USiNg
ANY OTHER WRENCH MAY DAMAgE
THE THREADS iN THE bARREL.
CHOKE TUBE INSTALLATION
1 Place the “safety” in the on safe
position. Always make sure the
shotgun is completely
unloaded. Keep the muzzle
pointed in a
safe direction.
2 Before installing a tube, check the choke tube threads in the muzzle,
as well as the threads on the choke tube to be sure they are clean. If
dirty, clean the tube with a nylon brush and gun solvent. Lightly oil
the choke tube and threads with a high-quality, lightweight gun oil.
3 Using your fingers, screw the appropriate tube into the muzzle
end of the barrel, threaded end outward. When it becomes finger-
tight, use the choke tube T-Wrench to firmly seat the tube.
NOTICE! USE ONLY THE iNvECTOR-DS T-WRENCH SUPPLiED WiTH YOUR
SHOTgUN TO iNSTALL AND REMOvE
iNvECTOR-DS CHOKE TUbES. USiNg
ANY OTHER WRENCH MAY DAMAgE
THE THREADS iN THE bARREL.
NOTICE! THE CHOKE TUbE SHOULD
bE PERiODiCALLY CHECKED TO
ASSURE THAT iT iS TigHT AND
FiRMLY SEATED. bEFORE CHECKiNg,
FOLLOW ALL THE CHOKE TUbE
REMOvAL AND iNSTALLATiON
SAFETY gUiDELiNES PREviOUSLY
OUTLiNED.
FigURE 22
Install or remove stock spacers to achieve
correct length of pull.
FigURE 21
Insert a screwdriver into the holes in the
recoil pad.
FigURE 20
1⁄2" and 1⁄4" stock spacers are included.
FigURE 19
Use the choke tube T-Wrench to remove and
install the choke tube in the barrel.
32
1 Use a #2 cross tip or Phillips screwdriver to remove the recoil pad
at the end of the buttstock (Figure 21, page 31). Place a small
amount of petroleum jelly on the screw access slits on the top and
bottom of the rear of the buttstock to prevent damaging the recoil
pad. Insert the screwdriver into each of the two access holes. Make
sure the tip of the screwdriver engages the head of the screw. Turn
the screw counterclockwise until the screw is completely loose
from the stock. When both screws are free, remove the recoil pad.
2 Add or subtract spacers to fit your firearm to your specifications
(Figure 22, page 31). After making an adjustment hold the shotgun
to your shoulder to determine if the new length feels comfortable.
Remember to always keep the muzzle pointed in a safe direction,
with the “safety” in the on safe position and make certain the
shotgun is completely unloaded.
3 When you are satisfied with the length of pull, start the screws
through the pad and spacer(s) into the holes in the stock.
4 Attach the recoil pad to the stock using the screwdriver. Turn the
screws clockwise to tighten. Do not overtighten the screws.
ADJUSTING CAST AND DROP AT COMB
bEFORE PERFORMiNg ADjUSTMENT
PROCEDURES, PLACE THE “SAFETY”
iN THE ON SAFE POSiTiON. OPEN THE
ACTiON AND MAKE CERTAiN YOUR
SHOTgUN iS COMPLETELY UNLOADED.
KEEP THE MUZZLE POiNTED iN A
SAFE DiRECTiON. FAiLURE TO
FOLLOW THESE WARNiNgS COULD
RESULT iN SERiOUS iNjURY
OR DEATH.
Six shims are included with your
new shotgun (Figure 23). The shims
fit between the buttstock and receiver, allowing customized
adjustments to the comb and heel. Each shim is labeled/stamped for
a specific amount of adjustment. The neutral shim, No. 2, is already
installed on your shotgun.
Drop at comb is defined as the place on the comb that your cheek
rests when taking aim. If drop at comb is correct, your eye naturally
falls in line with the sight. Shims marked 1, 2 and 3 do not give any
cast on or off. The stock remains straight. They only adjust drop
at comb.
These shims with their respective stamps are further clarified here:
• Shim 1 raises the comb approximately 1/16", and the heel
approximately 1/8".
• Shim 2 is neutral. This shim is already installed on the firearm.
• Shim 3 lowers the comb approximately 1/16", and the heel
approximately 1/8".
Cast is the offset of the buttstock from the longitudinal center line of
the firearm. Some right-handed shooters like the stock to angle away
(cast off) from their face, making their line of sight more directly in
line with the barrel. Angling the stock to the left for left-handed
shooters is “cast on.” Shims marked 1R1L, 2R2L, and 3R3L, will all
adjust drop at comb the same amount as shims 1, 2 and 3, and will
also adjust the cast right or left approximately 1/8". You will notice that
the two opposing edges of these spacers are different in thickness. For
right-handed shooters, install shims between the receiver and the
stock with the R facing the end of the buttstock, so its thicker side is
on the left side. This casts the stock slightly to the right, away from the
face of a right-handed shooter. If you turn the shim around so the L is
facing the end of the buttstock, and it will cast the stock to the left.
These shims with their respective stamps are further clarified below:
• Shim 1R1L raises the comb approximately 1/16", and the heel
approximately 1/8" and will adjust the cast on or cast off
approximately 1/8".
33
FigURE 23
Cast and drop adjustment shims. Shim 2 comes
on your shotgun and is not shown.
35
• Shim 2R2L adds the same amount of cast to the stock as shim
1R1L with neutral drop like shim 2.
• Shim 3R3L adds the same amount of cast to the stock as shims
1R1L and 2R2L, and lowers the comb approximately 1/16" and the
heel approximately 1/8".
INSTALLING A SHIM
IMPORTANT: Before loosening the buttstock to install shims, the
trigger group should be in position in the receiver. This aligns the
buttstock and makes assembly easier.
1 Make sure your shotgun is completely unloaded and the “safety” is
in the on safe position.
2 Use a #2 cross tip or Phillips screwdriver to remove the recoil pad
at the end of the buttstock (Figure 21, page 31). Place a small
amount of petroleum jelly on the screw access slits on the top and
bottom of the rear of the buttstock to prevent damaging the recoil
pad. Insert the screwdriver into each of the two access holes. Make
certain the tip of the screwdriver engages the head of the screw.
Turn the screw counterclockwise until the screw is completely
loose from the stock. When both screws are free, remove the
recoil pad.
3 Remove the stock insert to access the stock bolt nut (Figure 24).
4 Use a ½" socket wrench to
remove the stock bolt nut and
stock bolt washer. (Figure 25,
page 34).
5 Completely remove the
buttstock from the receiver,
along with the existing shim,
and install the shim you have
selected (Figure 26, page 35).
Make certain you have the
proper shim installed and in
position before reattaching the buttstock and recoil pad.
6 When you are satisfied with the fit, reattach the buttstock to the
receiver with the washer and the nuts.
7 Snug the nut with the ½" socket wrench, do not overtighten.
8 Reinstall the stock insert.
9 Reinstall the recoil pad with care, so as not to scratch or mar the
finish of the stock.
EXTRA BARRELS
bEFORE iNSTALLiNg AN ACCESSORY bARREL ON YOUR SHOTgUN, READ
THE FOLLOWiNg gUiDELiNES TO ENSURE THE bARREL/SHOTgUN
COMbiNATiON iS SAFE. PLACE THE “SAFETY” iN THE ON SAFE POSiTiON.
OPEN THE ACTiON AND MAKE CERTAiN YOUR SHOTgUN iS COMPLETELY
UNLOADED. KEEP THE MUZZLE POiNTED iN A SAFE DiRECTiON. FAiLURE
TO FOLLOW THESE WARNiNgS COULD RESULT iN SERiOUS iNjURY
OR DEATH.
The versatility of your new shotgun can be extended with an extra
barrel. A5 shotgun barrels are interchangeable within a given gauge
and chamber length. No special fitting is required. However, some
important restrictions must be observed:
FigURE 26
Install the shim between the stock and receiver.
FigURE 24
Remove the stock insert.
FigURE 25
Use a socket wrench to remove the stock bolt.
34
36
• Never use a barrel with a 3½" chamber on a shotgun designed for
barrels with a 3" chamber.
• Never use a barrel with a 3" chamber on a shotgun designed for
barrels with a 3½" chamber.
• Never use any other barrel from any other manufacturer on your
shotgun. Some other brands may seem similar, but the barrels are
not interchangeable.
• Never use a barrel from any other Browning shotgun.
CLEANING AND MAINTENANCE SUGGESTIONS
NOTICE! PLEASE TAKE NOTE OF THE FOLLOWiNg iNFORMATiON bEFORE
CLEANiNg YOUR FiREARM.
CLEANING PARTS WITH SPECIAL FINISHES
Be especially careful when cleaning firearms with camouflage,
Dura-Touch® Armor Coating and other special finishes. Always
prevent these surfaces from coming in contact with cleaning solvents,
barrel scrubbers and other strong chemicals. It is preferable to clean
these surfaces with a lightweight gun oil containing no solvents or
with a damp cloth and mild dish soap (be sure to keep water out of
the action). When cleaning your firearm’s bore and action, protect the
external finishes from any contact with chemicals used. Also avoid any
contact between external finishes and other strong chemicals like
those found in DEET-containing insect repellents, sunscreens, etc.
Damage to camouflage, Dura-Touch and other finishes caused by
chemicals is irreversible and not repairable.
bEFORE PERFORMiNg CLEANiNg PROCEDURES, PLACE THE “SAFETY” iN
THE ON SAFE POSiTiON. OPEN THE ACTiON AND MAKE CERTAiN YOUR
SHOTgUN iS COMPLETELY UNLOADED. KEEP THE MUZZLE POiNTED iN A
SAFE DiRECTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
WEAR EYE PROTECTiON WHEN DiSASSEMbLiNg AND CLEANiNg YOUR
SHOTgUN TO PREvENT SPRiNgS, SPRiNg-LOADED PARTS, SOLvENTS OR
OTHER AgENTS FROM CONTACTiNg YOUR EYES, RESULTiNg iN iNjURY.
KEEP ALL AMMUNiTiON AWAY FROM THE CLEANiNg AREA. NEvER
TEST THE MECHANiCAL FUNCTiON OF YOUR SHOTgUN WiTH LivE
AMMUNiTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
CLEANING THE BARREL
Your A5 shotgun will function better and more reliably over a longer
period of time if it is properly maintained and kept clean. You should
clean your shotgun after every day of shooting, and more often if it
becomes excessively dirty. At a minimum the barrel should be cleaned
and the action wiped clean and oiled after every day of shooting. The
slide assembly should require only occasional cleaning.
Normal maintenance can be accomplished with the barrel still
attached to the receiver (oiling and wiping down). More careful
cleaning requires removal of the barrel from the receiver (cleaning the
barrel) and the removal of the slide assembly. A complete cleaning
requires removal of the slide assembly and trigger group.
If a malfunction occurs, perform a thorough cleaning to see if it solves
the problem before seeking the services of a Browning Recommended
Service Center, the Browning Service Facility in Arnold, Missouri, or a
qualified gunsmith.
1 Place the “safety” in the on safe position. Open the action and
inspect the chamber and magazine to make certain they do not
contain any shells. Keep the muzzle pointed in a safe direction.
2 Remove the forearm and barrel as explained under “Disassembly”
on page 15.
37
38
3 Using a shotgun cleaning rod with tip and patch large enough for
a snug fit in the bore, insert the rod and a lightly oiled patch in the
breech end of the barrel and run back and forth through the bore
several times. Remove and clean the choke tube and choke tube
barrel threads with a nylon brush and lightly oil.
Browning offers a complete line of products to make cleaning your
firearm fast and easy. Be sure to follow all instructions when using
any product to clean your firearm.
4 Inspect the bore from both ends for leading and plastic residue
that often remain in the bores from the shot cups in modern
shells. Leading and plastic residue will appear as longitudinal
streaks and are usually more predominant near the muzzle and
just forward of the chamber. A normal amount of either is
common and not serious.
5 If leading or plastic residue seems excessive you can remove it by
brushing the bore with a bronze brush. Soak the brush or spray
the bore with a powder solvent first. Scrub until clean. To prevent
bristles from breaking off, push the brush fully through the barrel
each time before pulling it back through.
MOST SOLvENTS ARE HigHLY FLAMMAbLE. WEAR EYE PROTECTiON AND
PRACTiCE APPROPRiATE SAFETY MEASURES WHEN WORKiNg WiTH
SOLvENTS TO AvOiD SERiOUS iNjURY.
6 After all leading and plastic residues have been removed, run a
clean, dry patch through the bore. Follow this with a final, lightly
oiled patch to help prevent corrosion.
7 Reassemble the shotgun and wipe all exposed metal surfaces with
an oiled cloth making sure to wipe away all finger marks where
moisture could accumulate.
8 Inspect the barrel and chamber. Remove any cleaning patches or
debris that remains.
9 Lightly oil your firearm at the points described under “Periodic
Oiling” below. Regular, light oiling is extremely important to the
durability and reliable operation of your shotgun.
10 The wood surfaces can also be wiped with a quality, lightweight
gun oil or they can be polished with any quality furniture wax
(but not both).
PERIODIC OILING
The metal parts of a firearm should receive a light film of oil after
the firearm has been exposed to weather or handling.
Occasionally, a drop of lightweight gun oil may be placed inside
the receiver on the rails on which the slide assembly slides (Figure 3,
page 11). This reduces friction for smooth operation.
If the firearm has been exposed to excessive dust, dirt, mud or water,
the principal working parts including slide assembly, should be wiped
clean and lubricated with a light film of quality, lightweight gun oil.
NOTICE! DO NOT PLACE LARgE qUANTiTiES OF OiL iNTO THE ACTiON.
ExCESS OiL WiLL RUN bACK iNTO THE WOOD OF THE STOCK SOFTENiNg
THE WOOD, WiTH CONSEqUENTiAL LOOSENiNg OF THE STOCK.
REMOVAL OF THE TRIGGER GROUP
bEFORE REMOviNg THE TRiggER gROUP, PLACE THE “SAFETY” iN THE
ON SAFE POSiTiON. OPEN THE ACTiON AND MAKE CERTAiN YOUR
SHOTgUN iS COMPLETELY UNLOADED. KEEP THE MUZZLE POiNTED iN A
SAFE DiRECTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
WEAR EYE PROTECTiON WHEN DiSASSEMbLiNg AND CLEANiNg YOUR
SHOTgUN TO PREvENT SPRiNgS, SPRiNg-LOADED PARTS, SOLvENTS OR
OTHER AgENTS FROM CONTACTiNg YOUR EYES, RESULTiNg iN iNjURY.
39
40 41
KEEP ALL AMMUNiTiON AWAY FROM THE CLEANiNg AREA. NEvER
TEST THE MECHANiCAL FUNCTiON OF YOUR SHOTgUN WiTH LivE
AMMUNiTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
The trigger group can be removed if the action becomes excessively
dirty or wet. If this occurs, disassemble the action for a complete
cleaning as explained in the following sections. The trigger group of
your A5 shotgun can be removed in the field with only a small punch.
Disassembly of the action involves the removal of the slide assembly
and the trigger group. Disassembly beyond this point should only be
performed by a qualified gunsmith.
REMOVING THE TRIGGER GROUP
1 Place the slide assembly in the forward position by holding the
operating handle and depressing the bolt release button.
NOTICE! NEvER ALLOW THE ACTiON TO SLAM CLOSED bY PRESSiNg THE
bOLT RELEASE bUTTON WiTHOUT THE bARREL iNSTALLED. iF THE SLiDE
ASSEMbLY iS RELEASED FORWARD WiTH THE bARREL REMOvED, THE
OPERATiNg HANDLE WiLL STRiKE THE RECEivER AND CAUSE DAMAgE.
2 Use a non-marking punch or similar object to push inward on
the trigger guard pins, taking
care not to scratch the receiver
(Figure 27). Trigger group pins
may be removed from either
side of the receiver. Push the
trigger group pins through the
receiver. Pull on them from the
opposite side to remove them.
3 Grasp the trigger guard and pull
it up and out of the receiver
(Figure 28, page 41).
4 Perform any cleaning of the
parts and receiver cavity as
necessary. We suggest cleaning
the trigger group with a quality
aerosol gun solvent. Allow it to
dry and then very lightly oil the
moving parts.
NOTICE! DO NOT DiSASSEMbLE
THE TRiggER gROUP bEYOND
THiS POiNT.
REINSTALLATION OF THE
TRIGGER GROUP
1 Make sure the slide assembly is in the forward position.
2 Insert the rear of the trigger group into the receiver.
3 Press the bolt release button.
4 Insert the front of the trigger group into the receiver.
5 Align the holes in the trigger group with the holes on each side of
the receiver.
6 Insert the trigger guard pins and gently tap them into place
with a plastic or wooden mallet, again using caution not to
scratch the receiver.
REMOVAL OF THE SLIDE ASSEMBLY
The slide assembly can be removed if the action becomes excessively
dirty or wet. If this occurs, disassemble the action for a complete
cleaning as explained in the following sections. The slide assembly
of your A5 shotgun is designed to be removed in the field, without
special tools.
Disassembly of the action involves the removal of the slide assembly
and the trigger group. Disassembly beyond this point should only be
performed by a qualified gunsmith.
FigURE 28
Lift the trigger group from the receiver.
FigURE 27
Push the trigger group pins through
the receiver.
42
bEFORE REMOviNg THE SLiDE ASSEMbLY, PLACE THE “SAFETY” iN THE
ON SAFE POSiTiON. OPEN THE ACTiON AND MAKE CERTAiN YOUR
SHOTgUN iS COMPLETELY UNLOADED. KEEP THE MUZZLE POiNTED iN A
SAFE DiRECTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
WEAR EYE PROTECTiON WHEN DiSASSEMbLiNg AND CLEANiNg YOUR
SHOTgUN TO PREvENT SPRiNgS, SPRiNg-LOADED PARTS, SOLvENTS OR
OTHER AgENTS FROM CONTACTiNg YOUR EYES, RESULTiNg iN iNjURY.
KEEP ALL AMMUNiTiON AWAY FROM THE CLEANiNg AREA. NEvER
TEST THE MECHANiCAL FUNCTiON OF YOUR SHOTgUN WiTH LivE
AMMUNiTiON. FAiLURE TO FOLLOW THESE WARNiNgS COULD RESULT
iN SERiOUS iNjURY OR DEATH.
The slide assembly should occasionally be removed for cleaning
and lubrication. Follow the instructions in this section to remove
the slide assembly.
1 Lock the slide assembly rearward by first sliding the bolt latch to
the rear, then pulling the operating handle fully to the rear as
explained on page 13.
2 Remove the barrel and forearm as explained previously.
3 Carefully place the slide assembly in the forward position by
retaining the operating handle and pressing the bolt release button.
NOTICE! NEvER ALLOW THE ACTiON TO SLAM CLOSED bY PRESSiNg THE
bOLT RELEASE bUTTON WiTHOUT THE bARREL iNSTALLED. iF THE SLiDE
ASSEMbLY iS RELEASED FORWARD WiTH THE bARREL REMOvED, THE
OPERATiNg HANDLE WiLL STRiKE THE RECEivER AND CAUSE DAMAgE.
4 Remove the operating handle by pulling the operating handle
outward (Figure 29, page 42).
5 Slide the slide assembly forward and out of the receiver (Figure 30,
page 42).
DISASSEMBLING THE SLIDE ASSEMBLY
Figure 31 above shows the slide assembly completely disassembled
with parts labeled for reference. Follow the instructions in this section
to disassemble the slide assembly.
1 Remove the slide assembly as explained previously.
2 Press the firing pin completely into the rear of the slide assembly
and retain it in this position.
43
FigURE 31
The slide assembly shown disassembled for cleaning.
Slide Assembly
Unlocking Pin
Bolt
Recoil Spring
Firing Pin Retaining Pin
Slide Link
Firing Pin Spring
Firing Pin
FigURE 30
Slide the bolt forward and out of the receiver.
FigURE 29
Pull outward to remove the operating handle.
44 45
THE FiRiNg PiN iS UNDER SPRiNg TENSiON. WEAR EYE PROTECTiON
WHEN DiSASSEMbLiNg AND CLEANiNg YOUR SHOTgUN TO PREvENT
SPRiNgS, SPRiNg-LOADED PARTS, SOLvENTS OR OTHER AgENTS FROM
CONTACTiNg YOUR EYES, RESULTiNg iN iNjURY.
3 Insert a small punch into the hole in the bottom of the slide
assembly (Figure 32) and press the firing pin retaining pin out the
top of the slide assembly. Grasp the pin and remove it (Figure 33).
4 Carefully release the pressure on the firing pin and firing pin
spring. Remove the firing pin and firing pin spring (Figure 34).
5 Using a punch, press inward on the unlocking pin from the left side
of the slide assembly (Figure 35, page 44). Remove the unlocking
pin from the slide assembly.
6 Remove the bolt from the front of the slide assembly.
7 Remove the recoil spring from the front of the slide assembly.
Clean the parts of the slide as necessary using a quality aerosol gun
solvent. Allow the parts to dry and then lightly oil the parts.
ASSEMBLING THE SLIDE ASSEMBLY
1 Insert the recoil spring into the front of the slide assembly.
2 Insert the bolt into the front of the slide assembly (Figure 36). Be
sure the extractor is on the right side of the bolt slide. Align the
hole in slide assembly with the cut in the bolt.
3 Insert the unlocking pin into the hole in the right side of the slide
assembly and push it through the bolt. Ensure the alignment marks
on the left side of the bolt slide and unlocking pin are aligned to
allow the firing pin to pass though (Figure 37).
4 Insert the firing pin spring and firing pin into the opening at the
rear of the slide assembly.
FigURE 37
Install the unlocking pin as shown. The hole
must align with the firing pin.
FigURE 35
Remove the unlocking pin.
FigURE 36
Insert the bolt as shown.
FigURE 34
Remove the firing pin and firing pin spring.
FigURE 33
Remove the firing pin retaining pin.
FigURE 32
Push the firing pin retaining pin out.
46 47
Use a nylon brush to loosen caked-on grime.
Wipe the receiver cavity clean. Lightly oil the cavity and wipe it dry.
No further disassembly is required for cleaning.
2 Reassemble the trigger group, slide assembly, and the barrel
and forearm to the receiver as explained previously, making
sure the barrel and action have no cleaning patches inadvertently
left in them. Then wipe all exposed metal surfaces with an oiled
cloth, making sure to wipe clean all finger marks where moisture
could accumulate.
LUBRICATING THE ACTION TUBE AND SPRING
bEFORE LUbRiCATiNg THE ACTiON TUbE AND SPRiNg, PLACE THE
“SAFETY” iN THE ON SAFE POSiTiON. OPEN THE ACTiON AND MAKE
CERTAiN YOUR SHOTgUN iS COMPLETELY UNLOADED. KEEP THE MUZZLE
POiNTED iN A SAFE DiRECTiON. FAiLURE TO FOLLOW THESE WARNiNgS
COULD RESULT iN SERiOUS iNjURY OR DEATH.
WEAR EYE PROTECTiON WHEN DiSASSEMbLiNg AND LUbRiCATiNg YOUR
SHOTgUN TO PREvENT SPRiNgS, SPRiNg-LOADED PARTS, SOLvENTS OR
OTHER AgENTS FROM CONTACTiNg YOUR EYES, RESULTiNg iN iNjURY.
KEEP ALL AMMUNiTiON AWAY FROM
THE CLEANiNg AREA. NEvER TEST
THE MECHANiCAL FUNCTiON OF
YOUR SHOTgUN WiTH LivE
AMMUNiTiON. FAiLURE TO FOLLOW
THESE WARNiNgS COULD RESULT iN
SERiOUS iNjURY OR DEATH.
If you frequently use your shotgun
in inclement weather conditions,
oiling the action tube and spring
IMPORTANT: Do not force the
firing pin into the opening. If
the firing pin will not easily go
into the slide assembly, the hole
in the unlocking pin may need
to be aligned.
5 Press the firing pin fully into the
slide assembly and insert
the firing pin retaining pin into
the hole in the top of the
slide assembly.
INSTALLING THE SLIDE ASSEMBLY
1 Turn the shotgun upside down to make it easier to align the slide
link and the socket in the recoil spring follower.
2 Align slide assembly rails with the grooves in the receiver. Insert
the slide assembly into the receiver, slide link end first.
3 Replace the operating handle by inserting it in its slot in the
slide assembly.
4 Ensure the slide link is in the socket in the recoil spring follower
(Figure 38) by carefully opening and closing the action several
times to make sure the slide link and recoil spring follower are
properly engaged.
NOTICE! NEvER ALLOW THE ACTiON TO SLAM CLOSED bY PRESSiNg THE
bOLT RELEASE bUTTON WiTHOUT HAviNg THE bARREL iNSTALLED.
DAMAgE WiLL RESULT TO THE RECEivER AND OPERATiNg HANDLE.
5 Install the trigger group in the receiver as explained previously.
CLEANING THE ACTION
1 When the action becomes excessively dirty, remove the trigger
group and slide assembly from the receiver as explained under
“Removal of the Trigger Group” (page 39) and “Removal of the
Slide Assembly” (page 41). Clean with a gun solvent as necessary.
FigURE 39
Place a few drops of oil in the opening in the
action tube.
FigURE 38
Guide the bolt slide link into its socket in the
recoil spring follower.
48
YOUR FiREARM iN WATER) REqUiRE APPROPRiATE ATTENTiON, AND iN
SUCH CiRCUMSTANCES WE RECOMMEND YOU iMMEDiATELY TAKE YOUR
FiREARM TO A qUALiFiED gUNSMiTH.
MAINTENANCE OF OIL FINISH STOCKS
Keeping the oil-finished wood surface on your firearm looking its
best requires only a small amount of maintenance. When the surface
becomes spotted or dull, the affected area(s) can be treated using
rubbing alcohol on a soft, lint free cloth and allowed to dry. A small
amount of a linseed oil-based finish, such as Watco® Danish Oil Finish,
Deft® Danish Oil Finish, or Formby’s® Tung Oil Finish should then be
applied to the surface of the wood with a soft, lint free cloth according
to the manufacturer’s instructions. To treat the checkering, a small
amount of oil-based finish can be applied and then distributed evenly
using a toothbrush or other soft bristled brush.
MODELS WITH SPECIAL FINISHES
As with any firearm, the only way to preserve its pristine condition and
collector appeal is to never handle or fire it, which in turn would
deprive you of much of the enjoyment that comes with owning a fine
Browning firearm.
While special finishes such as engraving and gold plating greatly
enhance the aesthetic appeal of your shotgun, please be aware that
they are no more durable, and in some cases may even be slightly less
durable than more common firearm finishes.
As you use your shotgun, you can expect special finishes to wear in
much the same manner as any other firearm finish. These marks are
the honest product of the hours spent enjoying your firearm and each
scuff and scratch will probably have a good story to go along with it.
will aid in maintaining the performance and reliability of
your firearm.
IMPORTANT: Before loosening the buttstock to lubricate the action
tube and spring, the trigger group should be in position in the
receiver. This aligns the buttstock and makes assembly easier.
1 Remove the recoil pad and buttstock as explained previously.
2 Place a few drops of high-quality lightweight gun oil in the
opening in the rear of the action tube (Figure 39, page 47).
DO NOT ATTEMPT TO REMOvE THE ACTiON SPRiNg FROM THE ACTiON
TUbE. THE ACTiON TUbE iS EASiLY DAMAgED AND THE ACTiON SPRiNg
iS UNDER SPRiNg TENSiON. FAiLURE TO FOLLOW THiS WARNiNg COULD
RESULT iN SERiOUS iNjURY OR DAMAgE YOUR SHOTgUN.
3 Hold the shotgun with the muzzle down. Cycle the action using
the operating handle to operate the action several times to evenly
disperse the oil on the spring and inside the action tube.
NOTICE! DO NOT USE ExCESSivE LUbRiCANT. USiNg TOO MUCH
LUbRiCANT CAN iNTERFERE WiTH THE FUNCTiONiNg OF YOUR SHOTgUN.
DO NOT SPRAY SOLvENT iNSiDE THE ACTiON TUbE.
4 Carefully rest the shotgun vertically on a rag with the action tube
down for 15 minutes to allow excess oil to drain out of the action
tube. Wipe away any excess oil.
5 Lightly lubricate the external surface of the action tube.
6 Install the buttstock and recoil pad as explained previously.
NOTICE! DO NOT TAKE YOUR FiREARM’S ACTiON APART bEYOND WHAT
iS ExPLAiNED iN THiS OWNER’S MANUAL. THiS iS A SPECiALiZED,
FiNELY FiTTED MECHANiSM; ANY ATTEMPT TO DiSASSEMbLE THE iNNER
MECHANiSM MAY MAR iT FOR LiFE. iT iS UNNECESSARY, AND MAY DO
DAMAgE TO THE iNNER MECHANiSM TO DiSASSEMbLE iT FOR ROUTiNE
CLEANiNg AND OiLiNg. OF COURSE, MiSFORTUNES (SUCH AS DROPPiNg
49
50 51
NOTES
SERVICE OR REPAIR
If your firearm should require service or repairs, we suggest you first
contact a local recommended Browning Firearms Service Center.
To locate a service center visit browning.com, contact our Customer
Service Department or your Browning firearms dealer for the address
of the Service Center nearest you. Otherwise, you may send your
firearm directly to our Service Department in Arnold, Missouri.
Parts listings, Firearm Service Center lists, service procedures, service/
repair form and general product information are also found on the
internet at: browning.com. For technical questions about your firearm
or service, contact:
United States customers contact: Canadian customers contact:
Browning Service Department Browning Canada Sports Ltd/Ltée
3005 Arnold Tenbrook Road 5583 Chemin St-François
Arnold, MO 63010-9406 St-Laurent, Quebec H4S 1W6
Phone: (800) 322-4626 Phone: (514) 333-7261
When returning your firearm for servicing, you must do the following:
1 Be sure it is completely unloaded.
2 Remove the scope or other optics.
3 Package it securely in a cardboard container.
4 Enclose the service/repair form available at browning.com or a
letter that clearly describes the trouble experienced, the
ammunition used and the repairs desired. Also include your name,
email address (if possible) and a daytime phone number where
you can be reached.
5 If convenient, send a copy of the service/repair form or letter
to us separately.
6 Never return ammunition with your firearm. It is against postal
and most commerce regulations.
52
NOTES
BROWNING.COM
BROWNING US: Morgan, Utah 84050-9326
BROWNING CANADA: Browning Canada Sports Ltd/Ltée, St-Laurent, Quebec, H4S 1W6
BROWNING INTL: Parc Industriel des Hauts-Sarts, B-4040 Herstal, Belgium
A01203/11382
