Bunn Coffee Grinder G9 2 Hd S Users Manual Installation, Operating, 2T Installatiion & Operating Guide
Bunn-G9-2-Hd-G9-2-Hd-S-G9-2T-Hd-Owner-S-Manual bunn-g9-2-hd-g9-2-hd-s-g9-2t-hd-owner-s-manual
Bunn Coffee Grinder G9-2 10218.0000
G9-2T HD to the manual a05e24d9-6808-4284-b570-b63b168d8903
2015-02-04
: Bunn Bunn-Bunn-Coffee-Grinder-G9-2-Hd-S-Users-Manual-364154 bunn-bunn-coffee-grinder-g9-2-hd-s-users-manual-364154 bunn pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
G9-2 HD G9-2T HD G9-2 HD-S N IO N IO UT RY CA INJU AL . ON RD D RS ZA AN PE HA ERS CTS NG JE FI OB ER EP N PP G. KE REIG HO ENIN FO T OFE OP OU UT CH OR UT RY CA INJU AL . ON RD D RS ZA AN PE HA ERS CTS JE FINGOB ER EP N PP G. KE REIG HO ENIN FO T OFE OP OU UT CH OR INSTALLATION & OPERATING GUIDE BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070. 10218.0000Z 07/13 ©1994 Bunn-O-Matic Corporation BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor. 2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years. b) Compressors on refrigeration equipment - 5 years parts and 1 year labor. c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and labor for 4 years or 40,000 pounds of coffee, whichever comes first. These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality, damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty. THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon. If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment. THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages. 392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, Velocity Brew, Air Brew, Beverage Bar Creator, Beverage Profit Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer Control, Element, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Tea At Its Best, The Horizontal Red Line, Ultra are either trademarks or registered trademarks of Bunn-O-Matic Corporation. The commercial trifecta® brewer housing configuration is a trademark of Bunn-O-Matic Corporation. 2 10218 021513 CONTENTS Introduction...................................................................... 3 User Notices...................................................................... 3 Electrical Requirements.................................................... 4 CE Requirements.............................................................. 4 Operating Controls............................................................ 4 Initial Set-Up..................................................................... 5 Cleaning............................................................................ 5 Preventive Maintenance.................................................... 5 Coffee Grinding................................................................. 6 Adjustments...................................................................... 7 INTRODUCTION This equipment will store up-to six pounds of whole bean coffee in each of two hoppers and grind it to a preset grind and amount into an awaiting funnel and filter from most commercial drip coffee brewers. The equipment is only for indoor use on a sturdy counter or shelf. Adequate space must be available above the grinder to raise the lids when adding beans. Use only with whole bean coffee. The grind is preset at the factory to drip specifications as set forth by the United States Department of Commerce and adopted by the Coffee Brewing Center of the Pan American Coffee Bureau. Adjustments may be made to alter both the amount and grind from the factory setting. USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written for your protection. All notices on the grinder are to be kept in good condition. Replace any unreadable or damaged labels. WARNING Use only on a properly protected circuit capable of the rated load. Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles. An extension cord, when used, must be shorter than 20 feet if 16-gage 3-conductor wire, or shorter than 10 feet if 18-gage 3-conductor wire. FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE, FIRE, OR SHOCK HAZARD HAZARDOUS VOLTAGE READ THE ENTIRE OPERATING MANUAL INCLUDING THE LIMIT OF WARRANTY AND LIABILITY BEFORE BUYING OR USING THIS PRODUCT DISCONNECT FROM POWER SOURCE BEFORE REMOVING! 20545-0000D 01/04 © 1990 Bunn-O-Matic Corporation #20545.0000 #34891.0000 PERSONAL INJURY HAZARD. KEEP FINGERS AND FOREIGN OBJECTS OUT OF HOPPER OR CHUTE OPENING. #05876.0000 00824.0002 #37881.0000 3 10218 070913 ELECTRICAL REQUIREMENTS This grinder has an attached cordset and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz for 120V models and 230 volts ac, 10 amp single phase, 50 Hz for 230V models.. CE REQUIREMENTS • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C. • Appliance shall not be tilted more than 10° for safe operation. • An electrician must provide electrical service as specified in conformance with all local and national codes. • This appliance must not be cleaned by water jet. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of this appliance by a person responsible for its safety. • Children should be supervised to ensure they do not play with the appliance. • If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard. • Machine must not be immersed for cleaning. OPERATING CONTROLS Off/On/Start Switch OFF - (upper position) Switching to this position stops all operation of the grinder. ON - (middle position) The switch will return to this position after a grind cycle has begun and will remain in this position after grinding has ceased. START - (lower, momentary position) Pressing the switch initiates a timed grind cycle. Hopper Selector Switch Left - Switching to this position allows beans to be dispensed from the left hopper. Right - Switching to this position allows beans to be dispensed from the right hopper. P633 Dispense Timer The dispense timer controls the amount of beans that will leave the hopper in a grind cycle. The timer can be adjusted to dispense a different amount from each hopper. The scale is from 0.4 to 150.0 seconds. Refer to the Adjustments section for timer setting chart (page 8). 4 10218 070913 INITIAL SET-UP 1. Open the top lid. Clear all foreign objects and shipping material from the hopper compartment and the entrance to the grind chamber. 2. Remove the lower front inspection panel. 3. Plug-in the grinder. 4. Select either the right or left hopper with the selector switch. Do not press the start switch. 5. If grinder has an analog timer, proceed to step 6. If grinder has a digital timer, momentarily press the center (DISPLAY) button on the dispense timer panel. The readout will indicate the present timer setting in seconds and will remain displayed for five minutes. 6. Adjust the timer setting to obtain the desired amount of coffee for the selected hopper. P596 7. Repeat steps 4 thru 6 for the other hopper. 8. Fill the hopper compartments with whole bean coffee. (Capacity 6 pounds each). The grinder is now ready for use. CLEANING WARNING - Unplug the grinder before the removal of any panel or grind chamber-housing parts. 1. Clean all exterior surfaces using a damp cloth rinsed in any mild, nonabrasive, liquid detergent. Care should be taken not to scratch the grinder with any abrasive material. 2. Empty all beans from hopper(s). Plug in the grinder; place an empty funnel with filter into the funnel rails. Press and release the “GRIND” button. Run a few cycles until all coffee in the grind chamber is dispensed and disconnect the grinder from the power source. 3. Remove the upper front inspection panel. 4. Remove the two screws holding the front cover to the burr housing. Carefully remove the burr housing front cover. Clean inside surface with a dry stiff non-metallic bristle brush and wipe with a dry clean cloth. 5. Carefully remove the rotor cup, shear plate burr rotor and motor shaft extension from the grinder. Clean all parts with a dry stiff non-metallic bristle brush and wipe with a dry clean cloth. 6. Clean the grind chamber with a dry stiff non-metallic bristle brush and wipe with a dry clean cloth. 7. Reinstall the motor shaft extension, burr rotor, shear plate, rotor cup and front cover to the burr housing. 8. Reinstall the upper front inspection panel, 9. Refer to the “Adjustment” section of the Operating and Service manual for burr adjustments. PREVENTIVE MAINTENANCE Bunn-O-Matic Corporation recommends that preventive maintenance be performed at regular intervals. Maintenance should be performed by a qualified service technician. For Technical Service, contact Bunn-O-Matic® Corporation at 1-800-286-6070. NOTE: Replacement parts or service caused by failure to perform required maintenance is not covered by warranty. ® 6-Month Weekly Cleaning plus replace the dechaffer assembly. 05995.1000 Dechaffer Plate (package of 6) 1-Year 1. On grinders with slide plates check the slide plates and clean. 2. Inspect and clean/replace burrs and grind chamber if necessary. 3. Adjust the burrs and grind time to your specifications for particulate size and throw weight. 5 10218 070913 COFFEE GRINDING STEP 1 P597 STEP 2 P598 STEP 3 P599 STEP 4 P600 P601 STEPS 5 & 6 1. 2. 3. 4. Visually inspect the selected hopper for an ample supply of whole bean coffee. Place a paper filter into the brew funnel. The filter must not be folded-over or tilted to one side. Insert the funnel into the funnel rails and push until it stops. Momentarily press the start switch. The grinding action will stop automatically after the preset amount of ground coffee is dispensed into the funnel. 5. Remove the funnel from the grinder and level the bed of grounds by gently shaking. 6. The loaded funnel is now ready for use in any commercial drip coffee brewer according to the manufacturer’s instructions. 6 10218 113007 ADJUSTMENTS The grind can be set from very fine to very coarse. The amount may be adjusted for use in most commercial coffee brewers. The following procedures should be used to make adjustments. A change in the burr adjustment will also change the amount dispensed. Any adjustment of the burrs should be followed by an adjustment of the timer. RSE - FIN Burr Adjustment E OA C 1. Unplug the grinder and empty all beans from the hoppers. 2. Plug-in the grinder, momentarily press the off/on/start switch to the “START” (lower) position (with either hopper selected) and release, run a few grind cycles until all of the coffee in the grind chamber is used-up. 3. Remove the upper front inspection panel. 4. Early Models only, loosen the burr adjustment screw from its locked position. BUNN P1073 5. Early Models only, hand loosen the adjustment locking nut around the screw approximately one turn. Early Models 6. Press the off/on/start switch to the “START” (lower) position and release, slowly turn the adjusting screw in a clockwise direction until a metallic whine is heard due to the rubbing of the grinding burrs. (It may be necessary to start more than one grind cycle to obtain this sound.) 2 1 0 7. Early Models only, make a mark with a pen on the decal to note the position 3 15 of the arrow on the grind adjustment screw. 4 14 Adjusting screw Late Models, turn plastic grind indicator until screw slots line up with “O” on 5 13 Hash 6 the indicator. 12 Marks 7 8. The following settings approximately correspond to the CBC recognized grinds. 1 8 9 10 1 All are referenced from the arrow position noted in #7. FINE GRIND: Rotate the adjusting screw 7 hash marks in a counterclockwise P2820 Late Models direction. DRIP GRIND: Rotate the adjusting screw 8 hash marks in a counterclockwise direction. REGULAR (COARSE) GRIND: Rotate the adjusting screw 12 hash marks in a counterclockwise direction. 9. Early Models only, hold the adjusting screw in its set position with a screwdriver while tightening the lock nut to a snug position by hand. Slightly loosen the adjusting screw and retighten it to its prior position. The lock nut should now be tight against the burr housing front cover. Timer Adjustment 1. Unplug the grinder and remove the lower front inspection panel. 2. Determine the grind setting. (The factory setting is drip, to determine other settings, refer to the previous section.) I 0.0 HAZARDOUS VOLTAGE DISCONNECT FROM POWER SOURCE BEFORE REMOVING! DIGITAL TIMER 7 10218 070913 ADJUSTMENTS (cont.) 3. Use the table on the next page to find approximate timer setting for the grind and amount of coffee desired. 4. Plug-in the grinder. Select either the right or left hopper with the selector switch. Do not press the start switch. 5. If grinder has an analog timer, proceed to step 6. If grinder has a digital timer, momentarily press the center (DISPLAY) button on the dispense timer panel. The readout will indicate the present timer setting in seconds and will remain displayed for five minutes. 6. Adjust the timer setting to obtain the desired amount of coffee for the selected hopper. 7. Verify the setting by weighing a few samples. Use the following table as an approximate guide only. 8. Repeat steps 4 thru 7 for the other hopper. APPROXIMATE TIMER SETTINGS IN SECONDS Weight (ounces) Fine (7*) Drip (8*) Regular (12*) 1.5 0.5 0.5 0.5 1.75 0.7 0.6 0.6 2.0 1.0 0.8 0.8 2.25 1.4 1.4 1.2 2.5 1.9 1.8 1.6 2.75 2.4 2.2 2.0 3.0 2.9 2.7 2.5 3.25 3.3 3.1 2.9 4.0 4.8 4.4 4.0 6.0 8.6 7.9 7.5 8.0 12.0 11.5 10.9 10.0 15.7 15.1 14.1 12.0 19.6 18.5 17.5 14.0 23.5 22.0 20.9 16.0 27.0 25.3 24.3 *Hash mark settings. Refer to Adjustment-Burr section. 8 10218 091708
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Has XFA : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Instance ID : uuid:f4c2d8d1-7d48-4e4c-a130-b44d943380e4 Original Document ID : adobe:docid:indd:690a1841-b753-11db-94a7-a5d9f12266fd Document ID : xmp.id:C36641FA33206811822AEE447B369238 Rendition Class : proof:pdf History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2013:07:10 06:56:21-05:00 Derived From Instance ID : xmp.iid:64E60ED552246811822AA961484ED7EF Derived From Document ID : adobe:docid:indd:690a1841-b753-11db-94a7-a5d9f12266fd Derived From Original Document ID: adobe:docid:indd:690a1841-b753-11db-94a7-a5d9f12266fd Derived From Rendition Class : default Create Date : 2013:07:10 06:56:21-05:00 Modify Date : 2013:10:09 12:59:55-05:00 Metadata Date : 2013:10:09 12:59:55-05:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Format : application/pdf Title : installation, operating, G9-2 HD G9-2T HD G9-2 HD-S Installatiion & Operating Guide Description : Installation & Operating Guide for the G9-2 HD, G9-2T HD & G9-2 HD-S Automatic Portion Control Twin Hopper Whole Bean Coffee Grinders Creator : Subject : G9-2 HD, G9-2T HD, G9-2 HD-S, Twin Hopper Grinder, Whole Bean Coffee Grinder, Installation Manual, Operating Manual Producer : Adobe PDF Library 10.0.1 Trapped : False Keywords : G9-2 HD, G9-2T HD, G9-2 HD-S, Twin Hopper Grinder, Whole Bean Coffee Grinder, Installation Manual, Operating Manual Page Count : 8 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools