Bunn Single Gpr Dbc Owner S Manual Installation, Operating, DV With Smart Funnel Dual Voltage Installation & Operating Guide
2014-07-05
: Bunn Bunn-Single-Gpr-Dbc-Owner-S-Manual bunn-single-gpr-dbc-owner-s-manual bunn pdf
Open the PDF directly: View PDF 
.
Page Count: 9
| Download | |
| Open PDF In Browser | View PDF |
SINGLE® GPR DBC-DV WITH SMART FUNNEL® Dual Voltage Model INSTALLATION & OPERATING GUIDE BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service. 37994.0001B 08/13 ©2012 Bunn-O-Matic Corporation BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor. 2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years. b) Compressors on refrigeration equipment - 5 years parts and 1 year labor. c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and labor for 4 years or 40,000 pounds of coffee, whichever comes first. These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality, damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty. THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon. If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment. THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages. 392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, Velocity Brew, Air Brew, Beverage Bar Creator, Beverage Profit Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer Control, Element, Milk Texturing Fusion, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Sure Tamp, Tea At Its Best, The Horizontal Red Line, Ultra are either trademarks or registered trademarks of Bunn-O-Matic Corporation. The commercial trifecta® brewer housing configuration is a trademark of Bunn-O-Matic Corporation. INTRODUCTION The brewer incorporates a wireless interface system that allows the DBC Grinder to load certain information into the "programming chip" located inside the handle of the funnel. This information includes what flavor of coffee is being ground and what batch size will be brewed (small, medium, or large). Once the correct flavor name and amount of coffee is ground, the funnel is loaded into the brewer. The information from the funnel handle is then transferred into the brewer. The brewer then takes this information and dispenses the amount of water preset in the brewer for that particular flavor of coffee and batch size. The brewer can also be programmed to adjust different functions of the brewing process, such as brew temperature, brew volumes, bypass percentages, pulse brew, etc. This allows the operator to program a certain "recipe" for each coffee flavor to be brewed. Page 2 37994.1 080813 USER NOTICES The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels. 00658.0000 00986.0000 Optional Field Wiring 29710.0012A 120/208-240 V, 16.8-19.5 A, 3430-4540 W 1PH, 3-Wire + GND, 60HZ As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area. 00656.0001 29710.0012 03408.0004 37881.0000 MAIN ON/OFF SWITCH 03409.0004 12364.0000 39803.0000 00824.0002 Page 3 20201.5600 37994.1 031512 ELECTRICAL REQUIREMENTS WARNING - The brewer must be disconnected from the power source until specified in Initial Set-Up. Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements. BACK WHITE L2 RED WHITE NEUTRAL L1 BLACK GREEN WHITE NEUTRAL L1 BLACK GREEN L2 N L2 RED L2 RED WHITE WHITE NEUTRAL L1 BLACK L1 NEUTRAL L1 BLACK GREEN G GREEN L2 BLUE N L1 WHITE/VIOLET G P4337 FRONT 120 volt ac models 120/208 & 120/240 volt ac models Note: This electrical service consists of 2 current carrying conductors (L1 and Neutral) and a separate conductor for earth ground. Note: This electrical service consists of 3 current carrying conductors (Neutral, L1 and L2) and a separate conductor for earth ground. 120/208V 120/240V 120V P2853 DUAL VOLT TOGGLE SWITCH ELECTRICAL HOOK-UP CAUTION: Improper electrical installation will damage electronic components. 1. An electrician must provide electrical service. 2. Determine the available on-site electrical service. 3. Select the desired unit voltage based on the available on-site electrical service. 4. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source. 5. Remove the back access panel to gain access to the terminal block. 6. Feed the supply leads through the strain relief at the rear of the brewer. 7. Using the above diagrams, connect the desired electrical service to the field wiring terminal block. 8. If wiring the machine for operation on 120/208 or 120/240 volts with a Power Supply Cord, the Power Supply Cord must be UL Listed Flexible Cord Type SO, SJO, SJTO, HSJO or SJOW, No. 12 AWG, 4 Conductor, Rated 90° C. Attachment Plug Cap must be UL Listed, NEMA 14-20P or L14-20P Configuration, Rated 125/250V, 20 AMPS. The Power Supply Cord must be at least 3 feet long and maximum 6 feet long (measured from Strain Relief to end of the Attachment Plug Cap). 9. Connect the brewer to the power source and verify the voltage at the terminal block. 10. Set toggle switch on component bracket to the appropriate position and replace the access panel. 11. If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing has been hooked up, the brewer is ready for Initial Set-Up. Page 4 37994.1 080813 PLUMBING REQUIREMENTS This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 3⁄8" flare. NOTE: Bunn-O-Matic recommends 1⁄4" copper tubing for installations of less than 25 feet and 3⁄8" for more than 25 feet from the 1⁄2" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow. As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area. PLUMBING HOOK-UP 1. Flush the water supply line and securely attach it to the flare fitting or adapter located on rear of brewer. 2. Turn on the water supply. Page 5 37994.1 031512 OPERATING CONTROLS j e g f b ON / OFF FF /O ON IN CH MA WIT S P3438.25 a P3898 h d c (a) MAIN ON/OFF SWITCH This switch, located under the brewer behind the right front leg, turns power on and off to all components in the brewer. (b) BATCH SELECTOR SWITCHES Pressing the switch corresponding to the Small, Medium, or Large batch selects the amount of coffee to be brewed. Pressing a different switch after a brew cycle has been initiated does not change the brew batch in progress. Light indicates the selected batch to brew. (c) ENABLE BREW SWITCH Pressing the ENABLE BREW switch alternately turns the brewing side on and off. Pressing this switch during the brew cycle will interrupt the brew cycle, stopping the flow of water. Pressing this switch during the programming of the brewer will exit the setup and return to the main screen. (d) BREW SWITCH Momentarily pressing and releasing this switch begins a brew cycle. (e) PROGRAM SWITCH Pressing and holding the upper right hidden switch allows entry to the programming menus. Pressing and releasing the switch steps through each function screen during programming. (f) FUNCTION SCREEN This is the display which shows the various functions of the brewer and allows the programming to be accomplished. (g) FUNCTION SCREEN SWITCHES These are the hidden switches which are used to program the brewer. (h) FUNNEL SENSING COILS These are used to "receive" information from the Smart Funnel handle (coffee name and batch size), and also from RECIPE CARDS. (j) SCROLL BACKWARDS The upper left hidden switch can be used to scroll backwards through the function list. Page 6 37994.1 031512 INITIAL SETUP CAUTION – The brewer must be disconnected from the power source throughout the initial setup, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails of one of the brew stations. 2. Place an empty server under the funnel. 3. Connect the brewer to the power source. Main ON/OFF Switch (located in bottom cover behind right front leg on some brewers) must be in the ON position. Water will begin ° ° ° ° flowing into the tank and stop when the tank is filled to its capacity. Display will show PLEASE WAIT...TANK FILLING until tank is filled with water. 4. Wait approximately twenty minutes for the water in the tank to heat to the proper temperature. Display will show READY TO BREW...WATER TEMP: XXX˚ when tank is at operating temperature. NOTE: Brew water temperature is factory set at 200° F (93.3° C). Refer to TEMPERATURE SELECTION below should the water temperature need to be increased or decreased. When brew water temperature is changed, ready temperature should be increased or decreased accordingly. 5. Place a small vessel beneath the faucet and open the faucet handle. Release it when you hear the tank refilling. 6. Water volumes have been preset at the factory. Refer to adjustments for the Set Brew Volumes section of the Programming Manual on the Bunn-O-Matic website, at www.bunn.com should the volume need to be increased or decreased. 7. The brewer is now ready for use in accordance with the coffee brewing instructions. TEMPERATURE SELECTION SET TEMP - Range: 185˚F (85˚C) to 205˚F (96˚C) This function allows the operator to set the brew water temperature in the tank. It also sets the hot water faucet dispense temperature. SET TEMP: XXX° (-) DONE (+) Procedure to set brew temperature: 1. Press and hold upper right hidden switch until the display reads UNITS. Release switch. Continue to press and release switch until the display reads SET TEMP. 2. To adjust the brew temperature, press (-) to decrease or (+) to increase the brew temperature. 3. When finished, press and release DONE to save the new setting, exit the SET TEMP function and advance to the next function screen, SET READY. Another alternative is to press and release the ON/OFF switch (either on DUAL brewers) located on the front switch panel to exit the SET TEMP function and return to the MAIN SCREEN. Page 7 37994.1 031512 SET READY - Range: 185˚F (85˚C) to 203˚F (95˚C) This function allows the operator to set the minimum temperature allowable to start a brew cycle. The range can be from 185˚F (85˚C) to within 2˚F (-1.7°C) of the SET TEMP. The water must be at the SET READY temperature or higher for the display to indicate READY TO BREW. If brew lockout is enabled, the brewing process will not start below this READY temperature. NOTE: The upper limit for SET READY temperature is 2˚F (-1.7°C) less than the water temperature (SET TEMP) setting. SET READY: XXX° (-) DONE (+) Procedure to set ready temperature: 1. Press and hold upper right hidden switch until the display reads UNITS. Release switch. Press and release upper right hidden switch until the display reads SET READY. 2. To adjust the ready temperature, press the (-) button to decrease, or (+) to increase the ready temperature. 3. When finished, press and release DONE to save the new setting, exit the SET READY function and advance to the next function screen, REFILL. Another alternative is to press and release either ON/OFF switch located on the front switch panel to exit the SET READY function and return to the MAIN SCREEN. COFFEE BREWING 1. 2. 3. 4. Select the desired batch size on the grinder. It is not necessary to select a size on the brewer. Insert a BUNN filter into the funnel. Grind or pour the proper amount of fresh ground coffee into the filter and level the grounds by gently shaking. Slide the funnel into the funnel rails. If the grounds are not obtained through a grinder compatible with a Smart Funnel, a batch size must be chosen on the brewer. 5. Place an empty server under the funnel. 6. The ENABLE BREW switch must be ON. Momentarily press and release the BREW switch. If the brewer has the funnel lock option and if it is activated, once a brew cycle has been started the funnel is locked in place. There may be certain situations in which the brew cycle will not begin when the BREW switch is pressed: a) BREW TEMPERATURE TOO LOW - wait until heated or cancel BREW LOCKOUT option. b) FUNNEL NOT IN PLACE (or using a standard brew funnel) - cancel FUNNEL DETECT option. c) CHECK FUNNEL - remove funnel, empty previously brewed grounds and grind a new batch into the funnel. 7. If none of the above messages are displayed, the display will read NOW BREWING and the time remaining in the brew cycle. 8. Following the BREW will be a countdown of drip time DRIPPING which shows the time remaining until the funnel lock will release. Discard the grounds and filter only after visible dripping stops. Page 8 37994.1 031512 CLEANING 1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. 2. Check and clean the sprayhead. Use the pointed end of sprayhead cleaning tool (#38227.0000) to remove any mineral deposits from the sprayhead holes. 3. Insert the long end of sprayhead cleaning tool into the sprayhead fitting, and rotate several times to remove any mineral deposits from the fitting. 4. Insert the short end of sprayhead cleaning tool into the bypass fitting, and rotate several times to remove any mineral deposits from the fitting. NOTE: In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer and takes less than a minute. Page 9 37994.1 031512
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2013:08:21 15:17:46-05:00 Metadata Date : 2013:08:21 15:17:58-05:00 Modify Date : 2013:08:21 15:17:58-05:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:fc554e12-0ab9-934d-b7a6-4b259f9ed70f Original Document ID : adobe:docid:indd:fc64881d-4e6f-11dd-9363-848ffae150d2 Document ID : xmp.id:20C7211FE82668118C14F948856C2A83 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:94947700E82668118C14F948856C2A83 Derived From Document ID : xmp.did:F2CBC00429236811822AE0C07DF0151C Derived From Original Document ID: adobe:docid:indd:fc64881d-4e6f-11dd-9363-848ffae150d2 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2013:08:21 15:17:46-05:00 Format : application/pdf Title : installation, operating, SINGLE GPR DBC-DV with Smart Funnel Dual Voltage Model Installation & Operating Guide Description : Installation & Operating Guide for the SINGLE GPR DBC-DV with Smart Funnel Dual Voltage Model. Subject : SINGLE, GPR, DBC, DV, Digital Brewer Control, Dual Voltage, Smart Funnel, Installation Guide, Operating Guide Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 9 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools