Bunn Tf Server Dsg2 1 5 W Count Up Timer Owner S Manual Use, Care, Digital ThermoFresh 1.0 & 1.5 Gallon W/Count Use Care Information

2014-07-05

: Bunn Bunn-Tf-Server-Dsg2-1-1-5-W-Count-Up-Timer-Owner-S-Manual bunn-tf-server-dsg2-1-1-5-w-count-up-timer-owner-s-manual bunn pdf

Open the PDF directly: View PDF .
Page Count: 7

Download
Open PDF In Browser	View PDF

Digital
ThermoFresh®

1.0 & 1.5 Gallon Server
with Countup Timer

USE & CARE INFORMATION
CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE #1 of DAILY CLEANING.

BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644

43240.0009C

INTRODUCTION
This server is intended for use with a BUNN® DUAL® TF DBC®, SINGLE® TF DBC® or ICB family brewers.
When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server
and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf.
NOTE: Calibration of the brewer is required prior to the use of the Digital TF Server.

USER NOTICES
The notices on this server should be kept in good condition. Replace unreadable or damaged labels.

35710.0000

45457.0000

#39043.0000

#39043.0001

#39043.0002

DAILY CLEANING
CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY
NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method
consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing
solution using an approved non-chlorine sanitizer. Do not submerge server.
1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server
completely by opening the faucet.
2. Remove the sensor assembly, fill server with cleaning solution and thoroughly clean the inside of server.
3. Rinse server thoroughly using fresh water rinse.
4. Fill server with sanitizing solution and let the server set for 5 minutes, then drain through fully open faucet.
Thoroughly rinse server after sanitizing.
5. Remove the faucet handle/stem assembly by unscrewing the faucet nut just beneath the faucet handle.
6. Use enclosed cleaning brush to thoroughly clean the faucet body and tube.
7. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts in a mild detergent and water solution. Rinse the parts in hot water. Sanitize the parts for five minutes, thoroughly rinse, then air dry completely.
8. Use enclosed cleaning brush to thoroughly clean the fill tube of the sensor assembly.
NOTE: Never submerge the Digital ThermoFresh® Server Display or sensor assembly in water.
9. Wipe sensor assembly with a clean, damp cloth.
10. Reassemble the faucet and attach it to the dispenser.
11. Wash the entire outside surface of the server and display with a clean damp cloth.

PERIODIC CLEANING
1. Remove the sensor assembly from the server.
2. Remove the two thumb screws and slide display assembly from the server.
3. Wipe the surface of the display unit, area under the display unit, and sensor assembly with a clean damp
cloth.
4. Wash the entire outside surface of the sensor assembly with a mild detergent and water solution and rinse
with hot water. Do not submerse. NOTE: Thoroughly cleaning the sensor assembly fins will prevent inaccurate level readings.
5. Replace the display unit and sensor assembly.
2

43240.9 030912

SERVER WITH STAND
REPLACEMENT PARTS

1. 42554.1001 Display Kit, Countup (Includes items 2 - 4)

42826.1000
Screw, Thumb #6-32 x .25"
2. 46247.1000 Batteries, 4 Pack AAA
3. 42546.0001 Gasket, Battery Cover
4. 42547.0001 Cover, Battery

02361.0000
Screw, Pan Head #4-40 x .25"
5. 43135.0000 Handle, Faucet Black

43135.1002 Handle, Faucet Orange

43135.1004 Handle, Faucet Green
6. 29165.1002 Faucet Bonnet
7. 00601.1000 Faucet Spring (Package of 6)
8. 29164.1000 Faucet Stem (Package of 6)
9. 00600.1000 Faucet Seat Cup (Package of 6)
10. 42567.0000 Faucet Body
11. 42543.0000 Guard, Faucet

35074.1000
Screw, Pan Head M4 x .7 x .25

43231.0000
Washer, M4 x 9MM
12. 42584.1000 Plug, Front (Package of 10)
13. 42818.1001 Sensor Assy, 1.0 Gal (Includes items 14 &15)

42565.1000 Sensor Assy, 1.5 Gal (Includes items 14 &15)
14. 42563.1002 Cap, Sensor Assy (Package of 5)
15. 39043.0000 Decal, Do Not Submerge
16. 42562.0000* Handle, Server
17. 42758.0000* Shoulder Screw
18. 42585.1000 Plug, Rear (Package of 10)
19. 43246.1000 Cover Assy, Top

42761.0000*
Screw, Pan Head M4 x 9
20. 35710.0000 Decal, Warning Hot Liquid
21. 32591.1000 Tube, Silicone .50" ID x 12.0" LG (cut to length)
22. 28526.1000 Tube, Silicone .31" ID x 12.0" LG (cut to length)
23. 42912.0000 Foot, Rubber

43163.0000
Screw, Pan Head #8 x .75"
24. 42295.0001 Elbow, 90°
25. 42890.1000 Base Cover
26. 35016.0001 Insert, Stand
27. 38929.0002 Stand, Server

39617.0000
Screw, Pan Hd Plastite #6 x .75"
28. 38930.0002 Base Plate, Stand

44010.0000
Screw, Pan Head #8 x .50"
29. 39443.1003 Pad, Adhesive Back .75" Dia.
30. 38931.1002 Kit, Drip Tray (Includes item 31)
31. 38932.0000 Cover, Drip Tray
32. 45457.0000* Decal, Do not Submerge
33. 39043.0002* Decal, Do not Spray
34. 39043.0001* Decal, Do not Submerge Server
35. 42889.0000 Seal
36. 35071.0000 Decal, Black Wrap 1.5 Gal. (Not Illustrated)

37974.0000 Decal, Black Wrap 1.0 Gal. (Not Illustrated)
37. 35301.0001 Brush, Cleaning (Not Illustrated)

* Components of item 19

13
12

34
1
2

24
25
31

26
27

28
29
P4166

43240.9 111312

SERVER WITHOUT STAND
REPLACEMENT PARTS

1. 42554.1001 Display Kit, (Countup)(Includes items 2 - 4)

42826.1000
Screw, Thumb #6-32 x .25"
2. 46247.1000 Batteries, 4 Pack AAA
3. 42546.0001 Gasket, Battery Cover
4. 42547.0001 Cover, Battery

02361.0000
Screw, Pan Head #4-40 x .25"
5. 43135.0000 Handle, Faucet Black

43135.1002 Handle, Faucet Orange

35074.1000
Screw, Pan Head M4 x .7 x .25

43231.0000
Washer, M4 x 9MM
12. 42584.1000 Plug, Front (Package of 10)
13. 42818.1001 Sensor Assy, 1.0 Gal (Includes items 14 &15)

42565.1000 Sensor Assy, 1.5 Gal (Includes items 14 &15)
14. 42563.1002 Cap
15. 39043.0000 Decal, Do Not Submerge
16. 42562.0000* Handle, Server
17. 42758.0000* Shoulder Screw
18. 42585.1000 Plug, Rear (Package of 10)
19. 43246.1000 Cover Assy,

42761.0000*
Screw, Pan Head M4 x 9
20. 35710.0000 Decal, Warning Hot Liquid
21. 32591.1000 Tube, Silicone .50" ID x 12.0" (cut to length)
22. 28526.1000 Tube, Silicone .313" ID x 12.0" (cut to length)
23. 42912.0000 Foot, Rubber

43163.0000
Screw, Pan Head #8 x .75"
24. 42295.0001 Elbow, 90°
25. 42890.1000 Base Cover
26. 45457.0000* Decal, Do not Submerge
27. 39043.0002* Decal, Do not Spray

13
12

28
1
2
3

26
19

24
25
28. 39043.0001* Decal, Do not Submerge Server
29. 42889.0000 Seal
30. 35071.0000 Decal, Black Wrap 1.5 Gal. (Not Illustrated)

37974.0000 Decal, Black Wrap 1.0 Gal. (Not Illustrated)
31. 35301.0001 Brush, Cleaning (Not Illustrated)

* Components of item 19

STAND FOR SERVERS WITHOUT STAND

REPLACEMENT PARTS
-
1.
2.
3.
4.
5.

6.
7.
8.

39795.0003 Stand, Assy (Includes items 1 - 8)
39449.0005 Bracket, Rear
39448.0003 Bracket, Front
38929.0002 Stand, Server
00970.0000 Nut, Keps #8-32
38930.0002 Base Plate, Stand
44010.0000
Screw, Pan Head #8 x .50"
39443.1003 Pad, Adhesive Back .75" Dia.
38932.0000 Cover, Drip Tray
38931.1002 Drip Tray Kit (Includes item 7)

3
4
7

6
4

43240.9 111312

DIGITAL DISPLAY
The Digital ThermoFresh® Server is equipped with a digital probe and display called a Digital Sight Gauge. The probe
contains a circuit board designed to sense liquid levels & hold times. During the monitoring process, the probe sends
information to the display. The display then allows the user to monitor the liquid level and freshness (hold time) of the
beverage held in the server.

HORIZONTAL BAR

Using the Digital Sight Gauge display, the liquid level in the server can be
monitored by watching the horizontal bars. The 1.0 gallon display is equipped with
4 bars and the 1.5 gallon with 6 bars to represent the level inside the dispenser.
(each bar represents a quart, or one quarter of a gallon)
All four/six bars will be displayed when the server is full. When the level of
the liquid drops to a certain level, the highest bar on the display will no longer be
illuminated. These bars will continue to disappear as the level inside the dispenser drops. (See Fig. 1)

FIG. 1

COUNT UP TIMER

The Digital display is set to count up to 4:00 hours. The display counts up in one minute increments, flashing at 2:00
hours and continuing to flash once it reaches 4:00 hours. (See Fig. 1)

TIMER RESET
The display will reset to 0 when any of the following occurs:
• The liquid level in the server is increased by 1 bar for a sustained period of time. (brewing into, or adding additional
liquid to existing beverage)
• A fresh new beverage is brewed into the server.
• When the contact pins of the sensor assembly are disengaged from the display for more than 20 seconds.

DISPLAY OFF

When the sensor assembly on the server is removed or loosened for more than 20 seconds, the display on the
Digital Sight Gauge breaks contact with the pins on the surface of the server. When this happens, the outline that
surrounds the Horizontal Level Bars will flash on and off and the time disappears. This indicates that the display has
been disengaged from the probe and cannot receive data.
When the display is in place and engaged, but the server is empty, the outline surrounding the Horizontal Level Bars
will be on but not flashing and the Freshness Time will not be displayed. All other portions of the display will not be
visible. This indicates the display is engaged and ready to receive data from the probe, but the server is empty.
The only time the display will be completely blank, is when the batteries have
been removed or have expired. (See the “Battery Replacement” section for additional
Flashing Notification Table
information.)

FRESHNESS TIME
This unit is factory set to count up to 2:00 hours, and begin flashing. If a reset condition
has not occurred, it will continue to flash and count up to a maximum of 4:00 hours.
Flashing notification is adjustable and can be set between 15 minutes and 3 hours 45
minutes in 15 minute increments. Setting changed by opening battery compartment and
positioning rotary switch using a small screwdriver. Settings are defined in the Flashing
Notification Table.

LOW BATTERY INDICATOR
When the batteries in the display unit are running low, the display is also equipped with
a battery icon. The upper most bar used in monitoring liquid levels, will begin to flash in the
shape of a battery to indicate that it is time to replace the batteries. (See FIG. 1)
5

Position
Minutes
0
30
1
60
2
90
3
120 (Default)
4
150
5
180
6
210
7
240
8
15
9
45
A
75
B
105
C
135
D
165
E
195
F
Disable Timer

43240.9 030912

BATTERY REPLACEMENT
The Digital Sight Gauge display comes equipped with 4 AAA batteries. The batteries have
a use life of approximately 1 1/2 years under normal operating conditions.
NOTE: Batteries are not covered under product warranty.
To replace the batteries:
1. Remove the sensor assembly from the server.
2. Remove the two thumb screws and slide display assembly from the server.
3. Remove the two screws and cover on bottom of the display, Fig 2.
4. Replace used batteries with 4 AAA alkaline batteries.
5. Replace cover and two screws.
6. Replace display assembly and secure with two thumb screws.

FIG. 2

SENSOR ASSEMBLY INSTALLATION

Proper installation of the sensor assembly is achieved by aligning the contacts of the sensor assembly (B) with the
contacts on the back of the sight gauge (A) when the sever handle is in the fully open position. Once the sensor assembly
is engaged into the server, it is locked in place by flipping the handle over approximately 180° as shown in Fig 3.
A

P4164

FIG. 3
6

43240.9 070913

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers
and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor.
2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below:
a) Electronic circuit and/or control boards - parts and labor for 3 years.
b) Compressors on refrigeration equipment - 5 years parts and 1 year labor.
c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts
and labor for 4 years or 40,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be
commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the
applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured
by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation,
improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality,
damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but
not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN
prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office
Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an
authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under
warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make
modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such
individuals, whether oral or written, do not constitute warranties and should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the
applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair
is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for
the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS
EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION
AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of
use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities
or services, or any other special, incidental or consequential damages.
392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with
the stylized red line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design,
Cool Froth, DBC, Dr. Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet
Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment
Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com,
Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality
in Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, Velocity Brew, Air Brew, Beverage Bar Creator, Beverage
Profit Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer Control, Element, Milk Texturing Fusion, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Sure Tamp, Tea
At Its Best, The Horizontal Red Line, Ultra are either trademarks or registered trademarks of Bunn-O-Matic Corporation.
The commercial trifecta® brewer housing configuration is a trademark of Bunn-O-Matic Corporation.

43240.9 070913

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2013:08:22 09:57:55-05:00
Metadata Date                   : 2013:08:22 09:58:06-05:00
Modify Date                     : 2013:08:22 09:58:06-05:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Instance ID                     : uuid:c5bee5eb-8f7a-5d42-8ca2-36b07699ff2e
Original Document ID            : adobe:docid:indd:f831495e-4219-11df-b12c-ed5bd6f7a4b9
Document ID                     : xmp.id:B9C4B670842768118C14F948856C2A83
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:B8C4B670842768118C14F948856C2A83
Derived From Document ID        : xmp.did:C6B9A413D9206811822A972C41EAC97B
Derived From Original Document ID: adobe:docid:indd:f831495e-4219-11df-b12c-ed5bd6f7a4b9
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2013:08:22 09:57:55-05:00
Format                          : application/pdf
Title                           : use, care, Digital ThermoFresh 1.0 & 1.5 Gallon Server w/Count-up Timer Use & Care Information
Description                     : Use & Care Information for the Digital ThermoFresh 1.0 & 1.5 Gallon Server w/Count-up Timer.
Subject                         : ThermoFresh, Server, Digital, Count-up, Timer, use information, care information
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 7
Creator                         : Adobe InDesign CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools

Bunn Tf Server Dsg2 1 5 W Count Up Timer Owner S Manual Use, Care, Digital ThermoFresh 1.0 & 1.5 Gallon W/Count Use Care Information

Navigation menu

Versions of this User Manual:

Views

Navigation