C H Systems RF-CHW-ITI-S Door/Window and garage sensor used by Security Systems User Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	3235889
Application ID	iq1CagIV4AM2NOuBpFck3g==
Document Description	User Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	71.21kB (890100 bits)
Date Submitted	2016-12-21 00:00:00
Date Available	2017-06-10 00:00:00
Creation Date	2016-11-30 15:01:57
Producing Software	Microsoft® Publisher 2013
Document Lastmod	2016-11-30 15:01:57
Document Title	User Manual 2
Document Creator	Microsoft® Publisher 2013
Document Author:	Jim S

Hardwire to Wireless Converter
RF-CHW-ITI-16
RF-CHW-ITI-16
Description:
The RF-CHW-ITI-16 module allows the conversion
of hardwire security sensors to Qolsys wireless
technology. The module is a cost effective way of
upgrading a security system and using existing
hardwire security zones. The module supports both
magnetic contacts and powered zones (12VDC) as
motion detectors. The module uses the existing
EOL resistors so no re-wiring or changing out EOL’s
is required.
Installation:
Mounting location - if retrofitting an existing hardwire control panel, mount the module at that location to minimize splicing wires.
Note: if possible use the existing enclosure to house
the module and battery, remember the antenna on
the module must protrude from any metal enclosure.
Wiring (see wiring diagram)
Power transformer - 2 conductor
Zone wiring - from existing control panel
Zone power
Siren extension
Backup battery
Note: use 22 AGW minimum
Note: Make sure EOL resistors remain in place for
all zones
Programming:
The RF-CHW-ITI-16 module is a wireless device that
enrolls into the Qolsys control panel. The module has
a unique ID # that the control panel responds to for
tamper and low battery conditions. Also each zone is
assigned it’s own ID# for reporting purposes.
Module setup:
Clear Memory:
 Disconnect all power battery and transformer,
press and hold the memory reset button while
applying power
 The LED’s will flash indicating memory reset
 Power module by plugging in the transformer
and connecting backup battery if required
Notes:




Polarity on transformer marked as dashed line
on positive wire
Make sure all input EOL’s are properly wired for
N/O (parallel) or N/C (series) configuration
All zones must be wired with an EOL resistor,
either a 3K ohm from the accessory kit or the
existing resistor from the previous system
Place all zones in normal non alarm condition
Enrolling module and zones into the Qolsys panel - if
the module tamper and battery supervision are required the module must be enrolled into the control
panel (this step not required if no backup battery or
tamper are used)
Enroll module, EOL’s and zones
 Put the module in Learn Zone mode by pressing
the EOL Learn button and holding for 5 seconds,
all LEDs will flash, this process also learns in all of
the EOL’s
 Enter system programming on the Qolsys panel
 Settings menu, enter user code
 Installation menu, Security Sensors,
Auto Learn
Sensor
 To enroll the module trip the tamper zone





The Qolsys panel will indicate a sensor has been
detected and require pressing the control panel
OK to add the sensor
The Qolsys panel will display sensor characteristics that can be changed if required, when complete press Add New
The Qolsys panel returns to the Auto Learn Sensor and waits for the next sensor to be activated
Continue enrolling zones by activating the zone,
the Qolsys panel will respond with each successful wireless activation and required zone type
and name selection before the next zone is
tripped.
After all zones are enrolled press the EOL Learn
Button to exit program mode on the module, all
LED’s will go out
Note: Learning zones cannot be done if the EOL Calibration LED is Flashing or Off
Testing
 On the Qolsys panel enter Settings, enter user
code
 Press System Test, Sensor Test
 Activate all zones on the module and verify they
Pass
FCC label statement:
“This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.”
“Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.”
“Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment”
“RF Exposure Guidance: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 1.5cm between the
radiator and persons. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter, except in accordance
with FCC multi-transmitter product procedures.”
Specifications:
Input Voltage: 16.0VDC plug-in transformer
Backup Battery: 12VDC 5Ah max (optional)
Dimensions: 5.5” X 3.5”
Operating Temperature: 32 to 122F (0 to 50C)
Humidity: 95% RH Max
EOL Supervision: 1K to 10K Ohm
Input Zones: 16 (if used must have EOL resistor)
Zone Type—N/O or N/C compatible
Auxiliary Voltage Output: 12VDC @ 500mA
Cinch Stick Port: Field upgradable firmware
Tamper Zone: Separate zone input for tamper
Relay Contact—60VDC/1A Max, used to drive siren
or other device
Notes:
Module Switches:


EOL Learn - used to calibrate EOL resistors and enter
program mode
Memory Reset - clears memory of module

Used zones must have an EOL installed
If a backup battery is installed, the module must be enrolled into the Qolsys
panel
Make sure when installed the antenna is
free of all metal obstructions
Module LED’s
Plastic Enclosure
Metal Enclosure
Processor - flashes during normal operation
RF Xmit - flashes when an RF transmission is sent
EOL Cal: On - calibration required, Off - calibration
complete
Zones: Flash twice when ready to enroll, On - when
enrolled in programming and when tripped, Off when zone in normal condition
IC: 11817A-RFCHWITIS

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : en-US
Tagged PDF                      : Yes
Author                          : Jim S
Create Date                     : 2016:11:30 15:01:57-06:00
Modify Date                     : 2016:11:30 15:01:57-06:00
Producer                        : Microsoft® Publisher 2013
Creator                         : Microsoft® Publisher 2013

EXIF Metadata provided by EXIF.tools