C H Systems RF-CHWDSC Door/Window Sensors for Security System User Manual II

Cinch Systems, Inc Door/Window Sensors for Security System II

Contents

User Manual II

Hardwire to Wireless Converter RF-CHW-ITI-16 - 433 MHZ Descripon: The RF-CHW-ITI-16 module allows the conversion of hardwire security sensors to Qolsys wireless technology. The module is a cost eecve way of upgrading a security system and using exisng hardwire security zones. The module supports both magnec contacts and powered zones (12VDC) as moon detectors. The module uses the exisng EOL resistors so no re-wiring or changing out EOL’s is required. Installaon: Mounng locaon - if retrong an exisng hard-wire control panel, mount the module at that loca-on to minimize splicing wires. Note: if possible use the exisng enclosure to house the module and baery, remember the antenna on the module must protrude from any metal enclo-sure. Wiring (see wiring diagram) Power transformer - 2 conductor Zone wiring - from exisng control panel Zone power Siren extension Backup baery Note: use 22 AGW minimum Note: Make sure EOL resistors remain in place for all zones RF-CHW-ITI-16 - 433 MHz Programming: The RF-CHW-ITI-16 module is a wireless device that enrolls into the Qolsys control panel. The module has a unique ID # that the control panel responds to for tamper and low baery condions. Also each zone is assigned it’s own ID# for reporng purposes. Module setup: Clear Memory:  Disconnect all power baery and transformer, press and hold the memory reset buon while applying power  The LED’s will ash indicang memory reset  Power module by plugging in the transformer and connecng backup baery if required Notes:  Polarity on transformer marked as dashed line on posive wire  Make sure all input EOL’s are properly wired for N/O (parallel) or N/C (series) conguraon  All zones must be wired with an EOL resistor, either a 3K ohm from the accessory kit or the exisng resistor from the previous system  Place all zones in normal non alarm condion Enrolling module and zones into the Qolsys panel - if the module tamper and baery supervision are re-quired the module must be enrolled into the control panel (this step not required if no backup baery or tamper are used) Enroll module, EOL’s and zones  Put the module in Learn Zone mode by pressing the EOL Learn buon and holding for 5 seconds, all LEDs will ash, this process also learns in all of the EOL’s  Enter system programming on the Qolsys panel  Sengs menu, enter user code  Installaon menu, Security Sensors, Auto Learn Sensor  To enroll the module trip the tamper zone  The Qolsys panel will indicate a sensor has been detected and require pressing the control panel OK to add the sensor  The Qolsys panel will display sensor characteris-cs that can be changed if required, when com-plete press Add New  The Qolsys panel returns to the Auto Learn Sen-sor and waits for the next sensor to be acvated  Connue enrolling zones by acvang the zone, the Qolsys panel will respond with each success-ful wireless acvaon and required zone type and name selecon before the next zone is tripped.  Aer all zones are enrolled press the EOL Learn Buon to exit program mode on the module, all LED’s will go out Note: Learning zones cannot be done if the EOL Cali-braon LED is Flashing or O Tesng  On the Qolsys panel enter Sengs, enter user code  Press System Test, Sensor Test  Acvate all zones on the module and verify they Pass FCC label statement: “This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interfer-ence, and (2) this device must accept any interference received, including interference that may cause undesired operaon.” “Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcu-lar installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separaon between the equipment and receiver. —Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.” “Changes or modicaons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment” “RF Exposure Guidance: This equipment complies with FCC radiaon expo-sure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 1.5cm between the radiator and persons. This transmier must not be co-located or operang in conjuncon with any other antenna or transmier, except in accordance with FCC mul-transmier product procedures.”
Specicaons: Input Voltage: 16.0VDC plug-in transformer Backup Baery: 12VDC 5Ah max (oponal) Dimensions: 5.5” X 3.5” Operang Temperature: 32 to 122F (0 to 50C) Humidity: 95% RH Max EOL Supervision: 1K to 10K Ohm Input Zones: 16 (if used must have EOL resistor) Zone Type—N/O or N/C compable Auxiliary Voltage Output: 12VDC @ 500mA Cinch Sck Port: Field upgradable rmware Tamper Zone: Separate zone input for tamper Relay Contact—60VDC/1A Max, used to drive siren or other device Notes:  Used zones must have an EOL installed  If a backup baery is installed, the mod-ule must be enrolled into the Qolsys panel  Make sure when installed the antenna is free of all metal obstrucons Module Switches: EOL Learn - used to calibrate EOL resistors and enter program mode Memory Reset - clears memory of module Module LED’s Processor - ashes during normal operaon RF Xmit - ashes when an RF transmission is sent EOL Cal: On - calibraon required, O - calibraon complete Zones: Flash twice when ready to enroll, On - when enrolled in programming and when tripped, O - when zone in normal condion Metal Enclosure Plasc Enclosure

Navigation menu