CASTLES TECHNOLOGY VEGA5000 Contactless Module User Manual CA CLM user s manual

CASTLES TECHNOLOGY CO., LTD. Contactless Module CA CLM user s manual

5. User Manual--V5(RFID) R2

Castles Technology Contactless Reader Module CA-CLM User’s Manual 警語 依據低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Introduction Castles Technology CA-CLM contactless reader module is based on RFID (Radio Frequency Identification) technology and adopted HF (High Frequency) 13.56MHz band to have the communication protocol ISO14443 type A, B standard to interact the contactless smart card (a specified RFID tag) for specified applications like payment control and scheme. The reader has a baseband processer to handle host communication through RS232 interface, and to communicate RF analog front end (RF band chip) through SPI interface. RF chip is charged of air interface protocol and modulation to handle the communication with contactless smart card or so-called RFID tag through antenna. When the reader is operating, RF energy is transmitted by RF chip through antenna continually, and also the polling of response of card landing, once card is close to reader antenna, card will be energized by reader antenna RF energy, and responses to reader in specified standard for application required from host. The reading or writing of card will be occurred frequently during card landing on the reader. Also the indication LEDs and buzzer are included in this module for application need. Following is a block diagram about CA-CLM contactless reader to show the structure of RFID reader did.
CA-CLM Contactless Module Contactless MB MCU STM32103RD 64KB SRAM 384KB FLASH LQFP-64 NXP RC531 ISO14443 A, B Type ANTENNA/B LED x 4 TX, LED x4, GND FFC BUZZER RS-232 Driver UART TX,RX 5V, GND FFC 4pin Castles Contactless module ANTENNA/B MB FFC Cable 0.5mm 14P 8cm RS-232 (COM port), FFC Cable 1.0mm 5P J2 J1
Operation This module only allow 5V DC power source for operating power used, and a battery backup 3V DC for RTC used (backup power is required if necessary). The host side has a RS232 interface for host connection to receive or transmit relevant data from or to host may be like PC or Embedded system which AP (Application Program) executed. Antenna board should be connected to MB with a FFC cable when you received. The blue LED on antenna board will be on and buzzer beep when power on normally. At the meantime, this reader is operating and transmits RF (radio frequency) signal for card reading. Once contactless card landing or closing within reading distance, the orange LED will show the reading processing, and the green LED will show the success of reading. Alternative the red LED will show any error when reading process. May be buzzer beep also combine the LED indications in some case. Connection Type: FFC ZIF 1.0mm pitch 5 pin 90D upper contact (SCG BL113-05RU-TAND) Pin definition: Pin No. Name Type Remarks 1 GND Input 2 RS232 RX Input 3 RS232 TX Output 4 VCC_5V Input DC 5±0.05V Max. 350mA 5 VCC_BKP_3V Input RTC power 1.8V (MIN.) 3.6V(MAX.) Max. 5uA RF sensitive area in 2D, 3D In order to maintain good reading ability of contactless module for the requirements from EMV contactless certificate, the antenna board should be positioned and considered in specified area as following described.
2D: Any metal or conductive material is forbidden in the operating area shown as below. 3D: Any metal or conductive material is forbidden in the operating volume shown as below. Environmental  Operating temperature: 0℃ to 40℃  Storage temperature: -20 to 80℃ ℃  Operating humidity: 15% to 90%, non-condensing Certificate Compliant  EMVCo 2.0  EMC (CE、FCC CLASS B) Vendor Information Antenna/B 3.5 cm 3.5 cm 2.5 cm 2.5 cm 4 cm 4 cm 3.5 cm 2.5 cm
 虹堡科技股份有限公司 (Castles Technology Co., Ltd)  辛華熙 (Kevin Xin)  231 新北市新店區北新路三段 205 號2樓 (2F, No.205, Sec.3, Beixin Rd., Xindian District, New Taipei City 23143, Taiwan)
警語 依據低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. End Product Labeling:The final end product must be labeled in a visible area with the following:"Contains TX FCC ID: WIYVEGA5000"Manual Information to the end User:The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module.  The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu