CC and C Technologies WL1201M WLAN USB Module User Manual Revised OEM isntallation hardware manual

CC&C; Technologies, Inc. WLAN USB Module Revised OEM isntallation hardware manual

Contents

Revised OEM isntallation hardware manual

WL-1201MIEEE 802.11bWireless LAN USB ModuleHardware Installation GuideVersion 1.0
WLAN USB Module Installation Guide2REGULATION INFORMATIONThe WLAN USB Module must be installed and used in strict accordance with themanufacturer’s instructions. This module device complies with the following radiofrequency and safety standards.FCC (Federal Communications Commission)This module device complies with Part 15 of FCC Rules. Operation is subject tothe following two conditions:1. This module device may not cause harmful interference.2. This module device must accept any interference that may cause undesiredoperation.FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment. This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.The equipment has been tested and found to comply with the limits for a Class BDigital Device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction, may cause harmful interferenceto radio communication. However, there is no grantee that interference will not occurin a particular installation. If this equipment dose cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.--Consult the dealer or an experienced radio/TV technician for help.Notice: The Part 15 radio device operates on a non-interference basis with otherdevices operating at this frequency. Any changes or modification not expresslyapproved by the party responsible could void the user’s authority to operate thedevice.Warning: When installing the WLAN USB Dongle, the ferrite shall be placed on theUSB cable for compliance.
WLAN USB Module Installation Guide3Table of Contents1 Introduction .................................................................................................................... 42 Technical Specification of WLAN USB Module........................................................... 43 Installation...................................................................................................................... 54 PCB Drawing and Module Mounting ............................................................................ 6
WLAN USB Module Installation Guide41 IntroductionThanks for you purchasing Wireless Local Area Network (WLAN) USB module. Youare about to install a networking system that is not only fast and powerful, but also easy to setup and simple to maintain. In a short time you and those in your network will be able to sharea local printer and files, access the Internet, and roam about the office wire-freely.Using radio frequency (RF) technology, WLAN devices transmit and receive data overthe air, minimizing the need for wired connections. Thus, WLAN combine data connectivitywith user mobility, and, through simplified configuration, enable movable LANs. This wireless networking solution has been designed for both large and smallbusinesses, and it is scalable so that you can easily add more users and new network featuresas your business grows.This installation guide will assist you in installing the WLAN USB module.2 Technical Specification for WLAN USB Module.Product Name WLAN USB ModuleStandard IEEE802.11bFrequency Band 2.400GHz ~ 2.4835GHz unlicensed ISM bandSpread Spectrum DSSS (Direct Sequence Spread Spectrum)Modulation method DQPSK/DBPSK/CCKData Rate 1Mbps, 2Mbps, 5.5Mbps, 11MbpsOperation mode Peer-to-PeerAccess Point (need Access Points)Antenna External antenna.RF Output Power Max 8dBm.Receive Sensitivity Operating at 11Mbps: Better than 10^-5 BER @ –80dBmOperating Range Up to 200 m, depending on surrounding environment.Security 64-bit or 128-bit WEP (Wired Equivalent Privacy)Operating systemsupported Windows 98, Windows ME, Windows 2000, Windows XP,LinuxManagement Windows-based utility for configuration and statusmonitoringRegulation FCC part 15 for North AmericaI/O Interface USB portLED(option) ACTIVE(ACT) , POWER(PWR)Dimension 90(L) x 75(W) x 15(H) mmWeight 43 g (approximate)Input Power 5V DCOperating Temperature 0 ~ 50℃ (operation)Storage Temperature -20 ~ 70℃Humidity 5 ~ 90% (non-condensing)
WLAN USB Module Installation Guide53 InstallationThis section describes the procedures for installing the Wireless LAN USB moduleon your product/system.Before You StartBefore installation, please check your system in advance and ensure it meets theminimum requirements as described below.- Processor: Intel Celeron / Pentium II /Pentium III / Pentium IV; AMD Duron / Athlon- Operating System: Microsoft Windows 98 / ME / 2000 / XP/ Linux- System memory: 32MB at least.- Hard Drive Free Space: 5MB.
WLAN USB Module Installation Guide64 PCB Drawing and module Mounting.Connector PIN assignment:

Navigation menu