CC and C Technologies WL1302 802.11b Wireless Access Point User Manual Revised
CC&C; Technologies, Inc. 802.11b Wireless Access Point Users Manual Revised
Contents
- 1. DoC
- 2. Users Manual Revised
Users Manual Revised
User’s Manual Version: 2.1 Wireless LAN Access Point Trademarks Copyright @2003 Contents are subject to change without notice. All trademarks belong to their respective proprietors. Copyright Statement THIS DOCUMENT CONTAINS OF PROPRIETARY TECHNICAL INFORMATION THAT IS THE PROPERTY OF THIS COMPANY. AND NO PART OF THIS DOCUMENTATION MAY BE REPRODUCED, STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRICAL OR MECHANICAL, BY PHOTOCOPYING, RECORDING, OR OTHERWISE, WITHOUT THE PRIOR WRITTEN CONSENT OF THIS COMPANY. USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Revision History DATE REVISION 2003/7/14 First release 2003/7/22 Release 1.1; add information about time required on boot-up sequence. 2003/7/24 Release 1.2; modify the boot-up sequence notice in chapter 1 2003/8/4 Release 2.0; add configuration examples 2003/9/9 Release 2.1; modify power supply to DC 7.5V USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Terminology ANSI American National Standards Institute AP Access Point CCK Complementary Code Keying CSMA/CA Carrier Sense Multiple Access/ Collision Avoidance CSMA/CD Carrier Sense Multiple Access/ Collision Detection DHCP Dynamic Host Configuration Protocol DSSS Direct Sequence Spread Spectrum FCC Federal Communications Commission FTP File Transfer Protocol IEEE Institute of Electrical and Electronic Engineers IP Internet Protocol ISM Industrial, Scientific and Medical LAN Local Area Network MAC Media Access Control NAT Network Address Translation NT Network Termination PSD Power Spectral Density RF Radio Frequency SNR Signal to Noise Ratio SSID Service Set Identification TCP Transmission Control Protocol TFTP Trivial File Transfer Protocol WEP Wired Equivalent Privacy WLAN Wireless Local Area Network ii USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Table of Contents REVISION HISTORY .....................................................................................................................I TERMINOLOGY ........................................................................................................................... II INTRODUCTION.................................................................................................................... 1 1.1 1.2 1.3 1.4 1.5 INSTALLATION ..................................................................................................................... 4 2.1 2.2 HARDWARE INSTALLATION ................................................................................................. 4 SOFTWARE INSTALLATION ................................................................................................... 4 SOFTWARE CONFIGURATION ......................................................................................... 5 3.1 3.2 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.3.9 3.3.10 PACKAGE CONTENTS ........................................................................................................... 1 PRODUCT SPECIFICATIONS .................................................................................................. 1 PRODUCT FEATURES ........................................................................................................... 2 TOP PANEL DESCRIPTION .................................................................................................... 2 REAR PANEL DESCRIPTION.................................................................................................. 3 PREPARE YOUR PC TO CONFIGURE THE WIRELESS LAN ACCESS POINT ............................. 5 CONNECT TO THE WIRELESS LAN ACCESS POINT .............................................................. 7 MANAGEMENT AND CONFIGURATION ON THE WIRELESS LAN ACCESS POINT .................... 7 STATUS ............................................................................................................................ 7 WIRELESS BASIC SETTINGS ............................................................................................ 8 WIRELESS ADVANCED SETTINGS .................................................................................... 9 WIRELESS SECURITY SETUP .......................................................................................... 11 WIRELESS ACCESS CONTROL ........................................................................................ 12 LAN INTERFACE SETUP ................................................................................................ 14 STATISTICS .................................................................................................................... 15 UPGRADE FIRMWARE .................................................................................................... 16 SAVE /RELOAD SETTINGS .............................................................................................. 17 PASSWORD SETUP ......................................................................................................... 17 FREQUENTLY ASKED QUESTIONS (FAQ).................................................................... 19 4.1 4.2 WHAT AND HOW TO FIND MY PC’S IP AND MAC ADDRESS? ............................................. 19 WHAT IS WIRELESS LAN? ................................................................................................ 19 4.3 4.4 WHAT ARE ISM BANDS? ................................................................................................... 19 HOW DOES WIRELESS NETWORKING WORK?...................................................................... 19 iii USER’S MANUAL OF WLAN ACCESS POINT 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 Version: 2.1 WHAT IS BSSID? .............................................................................................................. 20 WHAT IS ESSID? .............................................................................................................. 20 WHAT ARE POTENTIAL FACTORS THAT MAY CAUSES INTERFERENCE? ................................ 21 WHAT ARE THE OPEN SYSTEM AND SHARED KEY AUTHENTICATIONS? ............................. 21 WHAT IS WEP? ................................................................................................................. 21 WHAT IS FRAGMENT THRESHOLD?.................................................................................... 21 WHAT IS RTS (REQUEST TO SEND) THRESHOLD?............................................................. 22 WHAT IS BEACON INTERVAL?............................................................................................ 22 WHAT IS PREAMBLE TYPE? ............................................................................................... 23 WHAT IS SSID BROADCAST? ............................................................................................ 23 CONFIGURATION EXAMPLES........................................................................................ 24 5.1 5.2 EXAMPLE ONE – DHCP ON THE LAN .............................................................................. 24 EXAMPLE TWO – FIXED IP ON THE LAN .......................................................................... 26 iv USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 1 Introduction The Wireless LAN Access Point is a portal that can act as the connection point between the Ethernet CSMA/CD protocol and the wireless CSMA/CA protocol. The Access Point can be easily integrated into your existing wireless network. In large installations, the roaming functionality provided by multiple Access Points allows wireless users to move freely throughout the facility while maintaining seamless, uninterrupted access to the network. This document describes the steps required for the initial IP address assign and other AP configuration. The description includes the implementation of the above steps. Notice: It will take about 25 seconds to complete the boot up sequence after powered on the WLAN Access Point; all LEDs are blank while booting except the Power LED, and after that the WLAN Activity LED will be flashing to show the WLAN interface is enabled and working now. 1.1 Package contents The package of the WLAN Access Point includes the following items, The Access Point The AC to DC power adapter The Documentation CD 1.2 Product Specifications Product Name WLAN Access Point Standard 801.11b(Wireless), 802.3(10BaseT), 802.3u(100BaseT) Data Transfer Rate 11Mbps(Wireless), 100Mbps(Ethernet) Modulation Method DBPSK/ DQPSK/ CCK Frequency Band 2.4GHz – 2.497GJz ISM Band, DSSS RF Output Power < 17 dBm Receiver Sensitivity 11Mbps better than 8% PER @ -80 dBm Operation Range 30 to 300 meters (depend on surrounding) Antenna External Antenna LED Power, Active (WLAN), Act/Link (Ethernet) Security 64 bit/ 128 bit WEP, MAC address filtering LAN interface One 10/100BaseT with RJ45 connector Power Consumption 7.5V DC Power Adapter USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Dimension 120 * 75 * 34 mm Operating Temperature 0 – 50oC ambient temperature Storage Temperature -20 - 70oC ambient temperature Humidity 5 to 90 % maximum (non-condensing) 1.3 Product Features Complies with IEEE 802.11b standard for 2.4GHz Wireless LAN. Supports 11Mbps data transfer rate with automatic fallback to 5.5M, 2M and 1Mbps. Supports bridging function between wireless and wired Ethernet interfaces. Supports 64-bit and 128-bit WEP encryption/decryption function to protect the wireless data transmission. Supports IEEE 802.3x full duplex flow control on 10/100M Ethernet interface. Supports DHCP client for Ethernet LAN interface auto IP address assignment. Supports clone MAC address function. Supports WEB based management and configuration. 1.4 Top Panel Description Figure 1 –WLAN Access Point Top Panel LED Indicator State 1. Power LED On The WLAN AP is powered on. Off The WLAN AP is powered off. 2. WLAN Activity LED Flashing Description Data is transmitting or receiving on the antenna. USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Off 3. LAN LINK/ACT LED Flashing Off No data is transmitting or receiving on the antenna. Data is transmitting or receiving on the LAN interface. No connection is established on LAN interface. 1.5 Rear Panel Description Antenna Power Reset LAN Figure 2 – WLAN Access Point Rear Panel Interfaces Description 1. Reset Push continually the reset button 5 seconds to reset the configuration parameters to factory defaults. 2. Power The power jack allows an external DC +7.5 V power supply connection. The external AC to DC adaptor provide adaptive power requirement to the WLAN AP. 3. LAN The RJ-45 socket allows LAN connection through a Category 5 cable. Support auto-sensing on 10/100M speed and half/ full duplex; comply with IEEE 802.3/ 802.3u respectively. 4. Antenna The Wireless LAN Antenna. USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 2 Installation 2.1 Hardware Installation Step One: Place the Wireless LAN Access Point to the best optimum transmission location. The best transmission location for your WLAN Access Point is usually at the geographic center of your wireless network, with line of sign to all of your mobile stations. Step Two: Connect the Wireless LAN Access Point to your wired network. Connect the Wireless LAN Access Point by category 5 Ethernet cable to your switch/ hub/ router/ xDSL modem or cable modem. A straight-through Ethernet cable with appropriate cable length is needed. Step Three: Supply DC power to the Wireless LAN Access Point. Use only the AC/DC power adapter supplied with the Wireless Access Point; it may occur damage by using a different type of power adapter. The hardware installation finished. 2.2 Software Installation There are no software drivers, patches or utilities installation needed, but only the configuration setting. Please refer to chapter 3 for software configuration. USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 3 Software configuration There are web based management and configuration functions allowing you to have the jobs done easily. The Wireless LAN Access Point is delivered with the following factory default parameters. Default IP Address: 192.168.1.254 Default IP subnet mask: 255.255.255.0 WEB login User Name:WEB login Password: 3.1 Prepare your PC to configure the Wireless LAN Access Point For OS of Microsoft Windows 95/ 98/ Me: 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. 3. 4. 5. 6. 7. Note: Windows Me users may not see the Network control panel. If so, select View all Control Panel options on the left side of the window Move mouse and double-click the right button on Network icon. The Network window will appear. Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. Select Protocol in the Network Component Type dialog box and click Add button. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. Select TCP/IP and click the properties button on the Network dialog box. Select Specify an IP address and type in values as following example. IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point. IP Subnet Mask: 255.255.255.0 8. Click OK and reboot your PC after completes the IP parameters setting. For OS of Microsoft Windows 2000, XP: 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Move mouse and double-click the right button on Network and Dial-up Connections USER’S MANUAL OF WLAN ACCESS POINT 3. 4. 5. 6. 7. Version: 2.1 icon. Move mouse and double-click the Local Area Connection icon. The Local Area Connection window will appear. Click Properties button in the Local Area Connection window. Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. Select Protocol in the Network Component Type dialog box and click Add button. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. Select TCP/IP and click the properties button on the Network dialog box. Select Specify an IP address and type in values as following example. IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point. IP Subnet Mask: 255.255.255.0 8. Click OK to completes the IP parameters setting. For OS of Microsoft Windows NT: 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Move mouse and double-click the right button on Network icon. The Network window will appear. Click Protocol tab from the Network window. 3. Check the installed list of Network Protocol window. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. 4. Select Protocol in the Network Component Type dialog box and click Add button. 5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example. IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point. IP Subnet Mask: 255.255.255.0 8. Click OK to completes the IP parameters setting. USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 3.2 Connect to the Wireless LAN Access Point Open a WEB browser, i.e. Microsoft Internet Explore, then enter 192.168.1.254 on the URL to connect the Wireless LAN Access Point. 3.3 Management and configuration on the Wireless LAN Access Point 3.3.1 Status This page shows the current status and some basic settings of the device, includes system, wireless and TCP/IP configuration information. Screenshot – Status Item Description System Alias Name It shows the alias name of this WLAN Access Point. Uptime It shows the duration since WLAN Access Point is powered on. Firmware version It shows the firmware version of WLAN Access Point. Wireless configuration SSID It shows the SSID of this WLAN Access Point. The SSID is the unique name of WLAN Access Point and shared among its service area, so all devices attempts USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 to join the same wireless network can identify it. Channel Number It shows the wireless channel connected currently. WEP It shows the status of WEP encryption function. Associated Clients It shows the number of connected clients (or stations, PCs). BSSID It shows the BSSID address of the WLAN Access Point. BSSID is a six-byte address. LAN configuration Attain IP Protocol It shows how the WLAN Access Point gets the IP address. The IP address can be set manually to a fixed one or set dynamically by DHCP server. IP Address It shows the IP address of the WLAN Access Point. Subnet Mask It shows the IP subnet mask of the WLAN Access Point. Default Gateway It shows the default gateway setting for the outgoing data packets. MAC Address It shows the MAC address of the WLAN Access Point. 3.3.2 Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients that may connect to your Access Point. Here you may change wireless encryption settings as well as wireless network parameters. USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Screenshot – Wireless Basic Settings Item Description Alias Name It is the alias name of this WLAN access point. The alias name can be 32 characters long. Disable Wireless LAN Tick on to disable the wireless LAN data transmission. Interface SSID It is the wireless network name. The SSID can be 32 bytes long. Channel Number Select the wireless communication channel from pull-down menu. Associated Clients Click the Show Active Clients button to open Active Wireless Client Table that shows the MAC address, transmit-packet, receive-packet and transmission-rate for each associated wireless client. Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. 3.3.3 Wireless Advanced Settings These settings are only for more technically advanced users who have a sufficient USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your Access Point. Screenshot – Wireless Advanced Settings Item Description Authentication Type Click to select the authentication type in Open System, Shared Key or Auto selection. Fragment Threshold Set the data packet fragmentation threshold, value can be written between 256 and 2346 bytes. Refer to 4.10 What is Fragment Threshold? RTS Threshold Set the RTS Threshold, value can be written between 0 and 2347 bytes. Refer to 4.11 What is RTS (Request To Send) Threshold? Beacon Interval Set the Beacon Interval, value can be written between 20 and 1024 ms. Refer to 4.12 What is Beacon Interval? Data Rate Select the transmission data rate from pull-down menu. Data rate can be auto-select, 11M, 5.5M, 2M or 1Mbps. Preamble Type Click to select the Long Preamble or Short Preamble support on the wireless data packet transmission. Refer to 10 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 4.13 What is Preamble Type? Broadcast SSID Click to enable or disable the SSID broadcast function. Refer to 4.14 What is SSID Broadcast? Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. 3.3.4 Wireless Security Setup This page allows you setup the WEP security. Turn on WEP by using encryption keys could prevent any unauthorized access to your wireless network. Screenshot – Wireless Security Setup Item Description Enable WEP Security Click the check box to enable WEP security function. Refer to 4.9 What is WEP? Key Length Select the WEP shared secret key length from pull-down menu. The length can be chose between 64-bit and 128-bit (known as “WEP2”) keys. The WEP key is composed of initialization vector (24 11 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 bits) and secret key (40-bit or 104-bit). Key Format Select the WEP shared secret key format from pull-down menu. The format can be chose between plant text (ASCII) and hexadecimal (HEX) code. Default Tx Key Set the default secret key for WEP security function. Value can be chose between 1 and 4. Encryption Key 1 Secret key 1 of WEP security encryption function. Encryption Key 2 Secret key 2 of WEP security encryption function. Encryption Key 3 Secret key 3 of WEP security encryption function. Encryption Key 4 Secret key 4 of WEP security encryption function. Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. WEP encryption key (secret key) length: Length 64-bit Format 128-bit ASCII 5 characters 13 characters HEX 10 hexadecimal codes 26 hexadecimal codes 3.3.5 Wireless Access Control If you enable wireless access control, only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point. When this option is enabled, no wireless clients will be able to connect if the list contains no entries. 12 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Screenshot – Wireless Access Control Item Description Enable WEP Security Click the check box to enable wireless access control. This is a security control function; only those clients registered in the access control list can link to this WLAN Access Point. MAC Address Fill in the MAC address of client to register this WLAN Access Point access capability. Comment Fill in the comments for the registered client. Apply Changes Click the Apply Changes button to register the client to new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. Current Access Control List It shows the registered clients that are allowed to link to this WLAN Access Point. Delete Selected Click to delete the selected clients that will be access right removed from this WLAN Access Point. Delete All Click to delete all the registered clients from the access allowed list. Reset Click the Reset button to abort change and recover the 13 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 previous configuration setting. 3.3.6 LAN Interface Setup This page is used to configure the parameters for local area network that connects to the LAN port of your Access Point. Here you may change the setting for IP address, subnet mask, DHCP, etc. Screenshot – LAN Interface Setup Item Description IP Address If the DHCP Client function is disabled, fill in the IP address of this WLAN Access Point. Subnet Mask If the DHCP Client function is disabled, fill in the subnet mask of this WLAN Access Point. Default Gateway If the DHCP Client function is disabled, fill in the default gateway for out going data packets. DHCP Client Select to enable or disable the DHCP client function from pull-down menu. 802.1d Spanning Tree Select to enable or disable the IEEE 802.1d Spanning Tree function from pull-down menu. Clone MAC Address Fill in the MAC address that is the MAC address to be 14 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 cloned. Clone MAC address is designed for your special application that request the clients to register to a server machine with one identified MAC address. Since that all the clients will communicate outside world through the WLAN Access Point, so have the cloned MAC address set on the wireless LAN access point will solve the issue. Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. 3.3.7 Statistics This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks. Screenshot – Statistics Item Description Wireless LAN Sent Packets It shows the statistic count of sent packets on the wireless LAN interface. 15 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Wireless LAN Received Packets It shows the statistic count of received packets on the wireless LAN interface. Ethernet LAN Sent Packets It shows the statistic count of sent packets on the Ethernet LAN interface. Ethernet LAN Received Packets It shows the statistic count of received packets on the Ethernet LAN interface. Refresh Click the refresh the statistic counters on the screen. 3.3.8 Upgrade Firmware This page allows you upgrade the Access Point firmware to new version. Please note, do not power off the device during the upload because it may crash the system. Screenshot – Upgrade Firmware Item Description Select File Click the Browse button to select the new version of web firmware image file. Upload Click the Upload button to update the selected web firmware image to the WLAN Access Point. Reset Click the Reset button to abort change and recover the 16 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 previous configuration setting. 3.3.9 Save /Reload Settings This page allows you save current settings to a file or reload the settings from the file that was saved previously. Besides, you could reset the current configuration to factory default. Screenshot – Save/Reload Settings Item Description Save Settings to File Click the Save button to download the configuration parameters to your personal computer. Load Settings from File Click the Browse button to select the configuration files then click the Upload button to update the selected configuration to the WLAN Access Point. Reset Settings to Default Click the Reset button to reset the configuration parameter to factory defaults. 3.3.10 Password Setup This page is used to set the account to access the web server of Access Point. Empty user name and password will disable the protection. 17 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Screenshot – Password Setup Item Description User Name Fill in the user name for web management login control. New Password Fill in the password for web management login control. Confirmed Password Because the password input is invisible, so please fill in the password again for confirmation purpose. Apply Changes Clear the User Name and Password fields to empty, means to apply no web management login control. Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. 18 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 4 Frequently Asked Questions (FAQ) 4.1 What and how to find my PC’s IP and MAC address? IP address is the identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 191.168.1.254 could be an IP address. The MAC (Media Access Control) address is your computer's unique hardware number. (On an Ethernet LAN, it's the same as your Ethernet address.) When you're connected to the Internet from your computer (or host as the Internet protocol thinks of it), a correspondence table relates your IP address to your computer's physical (MAC) address on the LAN. To find your PC’s IP and MAC address, Open the Command program in the Microsoft Windows. Type in ipconfig /all then press the Enter button. Your PC’s IP address is the one entitled IP Address and your PC’s MAC address is the one entitled Physical Address. 4.2 What is Wireless LAN? A wireless LAN (WLAN) is a network that allows access to Internet without the need for any wired connections to the user’s machine. 4.3 What are ISM bands? ISM stands for Industrial, Scientific and Medical; radio frequency bands that the Federal Communications Commission (FCC) authorized for wireless LANs. The ISM bands are located at 915 +/- 13 MHz, 2450 +/- 50 MHz and 5800 +/- 75 MHz. 4.4 How does wireless networking work? The 802.11 standard define two modes: infrastructure mode and ad hoc mode. In infrastructure mode, the wireless network consists of at least one access point connected to the wired network infrastructure and a set of wireless end stations. This configuration is called a Basic Service Set (BSS). An Extended Service Set (ESS) is a set of two or more BSSs forming a single subnetwork. Since most corporate WLANs require access 19 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 to the wired LAN for services (file servers, printers, Internet links) they will operate in infrastructure mode. Example 1: wireless Infrastructure Mode Ad hoc mode (also called peer-to-peer mode or an Independent Basic Service Set, or IBSS) is simply a set of 802.11 wireless stations that communicate directly with one another without using an access point or any connection to a wired network. This mode is useful for quickly and easily setting up a wireless network anywhere that a wireless infrastructure does not exist or is not required for services, such as a hotel room, convention center, or airport, or where access to the wired network is barred (such as for consultants at a client site). Example 2: wireless Ad Hoc Mode 4.5 What is BSSID? A six-byte address that distinguishes a particular a particular access point from others. Also know as just SSID. Serves as a network ID or name. 4.6 What is ESSID? The Extended Service Set ID (ESSID) is the name of the network you want to access. It is used to identify different wireless networks. 20 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 4.7 What are potential factors that may causes interference? Factors of interference: Obstacles: walls, ceilings, furniture… etc. Building Materials: metal door, aluminum studs. Electrical devices: microwaves, monitors and electrical motors. Solutions to overcome the interferences: Minimizing the number of walls and ceilings. Position the WLAN antenna for best reception. Keep WLAN devices away from other electrical devices, eg: microwaves, monitors, electric motors, … etc. Add additional WLAN Access Points if necessary. 4.8 What are the Open System and Shared Key authentications? IEEE 802.11 supports two subtypes of network authentication services: open system and shared key. Under open system authentication, any wireless station can request authentication. The station that needs to authenticate with another wireless station sends an authentication management frame that contains the identity of the sending station. The receiving station then returns a frame that indicates whether it recognizes the sending station. Under shared key authentication, each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802.11 wireless network communications channel. 4.9 What is WEP? An optional IEEE 802.11 function that offers frame transmission privacy similar to a wired network. The Wired Equivalent Privacy generates secret shared encryption keys that both source and destination stations can use to alert frame bits to avoid disclosure to eavesdroppers. WEP relies on a secret key that is shared between a mobile station (e.g. a laptop with a wireless Ethernet card) and an access point (i.e. a base station). The secret key is used to encrypt packets before they are transmitted, and an integrity check is used to ensure that packets are not modified in transit. 4.10 What is Fragment Threshold? The proposed protocol uses the frame fragmentation mechanism defined in IEEE 802.11 to achieve parallel transmissions. A large data frame is fragmented into several 21 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 fragments each of size equal to fragment threshold. By tuning the fragment threshold value, we can get varying fragment sizes. The determination of an efficient fragment threshold is an important issue in this scheme. If the fragment threshold is small, the overlap part of the master and parallel transmissions is large. This means the spatial reuse ratio of parallel transmissions is high. In contrast, with a large fragment threshold, the overlap is small and the spatial reuse ratio is low. However high fragment threshold leads to low fragment overhead. Hence there is a trade-off between spatial re-use and fragment overhead. Fragment threshold is the maximum packet size used for fragmentation. Packets larger than the size programmed in this field will be fragmented. If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may want to try lowering your fragmentation threshold. This will cause packets to be broken into smaller fragments. These small fragments, if corrupted, can be resent faster than a larger fragment. Fragmentation increases overhead, so you'll want to keep this value as close to the maximum value as possible. 4.11 What is RTS (Request To Send) Threshold? The RTS threshold is the packet size at which packet transmission is governed by the RTS/CTS transaction. The IEEE 802.11-1997 standard allows for short packets to be transmitted without RTS/CTS transactions. Each station can have a different RTS threshold. RTS/CTS is used when the data packet size exceeds the defined RTS threshold. With the CSMA/CA transmission mechanism, the transmitting station sends out an RTS packet to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before sending the actual packet data. This setting is useful for networks with many clients. With many clients, and a high network load, there will be many more collisions. By lowering the RTS threshold, there may be fewer collisions, and performance should improve. Basically, with a faster RTS threshold, the system can recover from problems faster. RTS packets consume valuable bandwidth, however, so setting this value too low will limit performance. 4.12 What is Beacon Interval? In addition to data frames that carry information from higher layers, 802.11 includes management and control frames that support data transfer. The beacon frame, which is a type of management frame, provides the "heartbeat" of a wireless LAN, enabling 22 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 stations to establish and maintain communications in an orderly fashion. Beacon Interval represents the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point). 4.13 What is Preamble Type? There are two preamble types defined in IEEE 802.11 specification. A long preamble basically gives the decoder more time to process the preamble. All 802.11 devices support a long preamble. The short preamble is designed to improve efficiency (for example, for VoIP systems). The difference between the two is in the Synchronization field. The long preamble is 128 bits, and the short is 56 bits. 4.14 What is SSID Broadcast? Broadcast of SSID is done in access points by the beacon. This announces your access point (including various bits of information about it) to the wireless world around it. By disabling that feature, the SSID configured in the client must match the SSID of the access point. Some wireless devices don't work properly if SSID isn't broadcast (for example the D-link DWL-120 USB 802.11b adapter). Generally if your client hardware supports operation with SSID disabled, it's not a bad idea to run that way to enhance network security. However it's no replacement for WEP, MAC filtering or other protections. 23 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 5 Configuration Examples 5.1 Example One – DHCP on the LAN Sales division of Company ABC likes to establish a WLAN network to support mobile communication on sales’ Notebook PCs. MIS engineer collects information and plans the WLAN Access Point implementation by the following configuration. All the sales’ Notebook PCs will get IP address automatically from the DHCP server. DHCP server also assigns the IP address of WLAN Access Point LAN interface, so before you can manage the WLAN Access Point through the WEB browser, you need to get the IP address of the LAN interface. LAN configuration Attain IP Automatically (DHCP); enable DHCP client function. WLAN configuration SSID SDWLAN Channel Number SSID: SDWLAN Channel: 1 DHCP client SSID: SDWLAN Channel: 1 DHCP client SSID: SDWLAN Channel: 1 DHCP client SSID: SDWLAN Channel: 1 DHCP client SSID: SDWLAN Channel: 1 DHCP Power adapter Ethernet cable Switch/ HUB xDSL/ CM Internet DHCP server Figure 3 – Configuration Example One – DHCP on the LAN 24 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Configure the LAN interface: Open LAN Interface Setup page and enable the DHCP Client function. Press button to confirm the configuration setting. Configure the WLAN interface: Open WLAN Interface Setup page, enter the SSID “SDWLAN”, Channel Number “1”. Press button to confirm the configuration setting. 25 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 5.2 Example Two – Fixed IP on the LAN Company ABC likes to establish a WLAN network to support mobile communication on all employees’ Notebook PCs. MIS engineer collects information and plans the WLAN Access Point implementation by the following configuration. LAN configuration IP Address Subnet Mask Default Gateway WLAN configuration SSID Channel Number 192.168.1.254 255.255.255.0 192.168.1.10 MyWLAN SSID: MyWLAN Channel: 6 IP: 192.168.1.32 SSID: MyWLAN Channel: 6 IP: 192.168.1.31 SSID: MyWLAN Channel: 6 IP: 192.168.1.30 SSID: MyWLAN Channel: 6 IP: 192.168.1.33 SSID: MyWLAN Channel: 6 IP: 192.168.1.254 Power adapter Ethernet cable Switch/ HUB xDSL/ CM Internet Router IP: 192.168.1.20 IP: 192.168.1.10 Figure 4 – Configuration Example Two – Fixed IP on the WAN 26 USER’S MANUAL OF WLAN ACCESS POINT Version: 2.1 Configure the LAN interface: Open LAN Interface Setup page, enter the IP Address “192.168.1.254”, Subnet Mask “255.255.255.0”, Default Gateway “192.168.1.10”. Press button to confirm the configuration setting. Configure the WLAN interface: Open WLAN Interface Setup page, enter the SSID “MyWLAN”, Channel Number “6”. Press button to confirm the configuration setting. 27 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. "CC&C declare that WL-1302 (802.11b Wireless Access Point) is limited in CH1~CH11 by specified firmware controlled in USA." IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. INFORMATION TO USER: The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res Create Date : 2003:10:27 01:38:46Z Modify Date : 2003:11:10 10:59:25+08:00 Page Count : 34 Creation Date : 2003:10:27 01:38:46Z Mod Date : 2003:11:10 10:59:25+08:00 Producer : Acrobat Distiller 5.0 (Windows) Author : Demi Metadata Date : 2003:11:10 10:59:25+08:00 Creator : Demi Title : Microsoft Word - WAP_UMv2.1_English_revised_p34.doc Has XFA : NoEXIF Metadata provided by EXIF.tools