CC and C Technologies WL2203 WLAN 11g USB Adapter User Manual SIS136

CC&C; Technologies, Inc. WLAN 11g USB Adapter SIS136

Contents

Users Manual Revised

USER’S GUIDEVERSION 1.02004/07/12Tested To ComplyWith FCC StandardsFOR HOME OR OFFICE USEIEEE 802.11b/gWireless LAN USBAdapter
© All rights reserved.All trade names are registered trademarks of respective manufacturers listed.This manual may not be copied in any media or form without the written consent of original maker.
TABLE OF CONTENTSInformation To User .................................................... i1. Introduction ........................................................... 12. Wireless LAN Basics .................................................. 33. IP ADDRESS ............................................................ 44. Install Driver/Utility ................................................. 55. Wireless Network Configuration .................................. 75.1 General Connection Setting .................................. 85.2 WEP Encryption Key Setting ................................. 95.3 WPA Encryption Setting ....................................... 105.4 Profile ............................................................ 115.5 Advanced Setting .............................................. 125.6 System Information ........................................... 136. Technical Specifications ............................................. 147. Troubleshooting ...................................................... 158. Glossary ................................................................ 16
INFORMATION TO USERFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, thereis no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference byone of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device may not causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approvedby the party responsible for compliance could void the user's authority tooperate this equipment.IMPORTANT NOTE:FCC Radiation Exposure Statement: i•This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.•This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
REGULATORY INFORMATIONThe channel identifiers, channel center frequencies, andregulatory domains of each 22-MHz-wide channel are shown infollowing Table.iiChannel CenterIdentifier Frequency(MHZ) NorthAmerica12412ˇˇˇ22417ˇˇˇ32422ˇˇˇˇ42427ˇˇˇˇ52432ˇˇˇˇ62437ˇˇˇˇ72442ˇˇˇˇ82447ˇˇˇˇ92452ˇˇˇˇ10 2457ˇˇˇˇˇ11 2462ˇˇˇˇˇ12 2467ˇˇˇ13 2472ˇˇˇ14 2484ˇRegulatory DomainsJapan ETSI Israel France MexicoWLAN Mini USB Adapter must be installed and used in strictaccordance with the instructions. This device complies with thefollowing radio frequency and safety standards.USA - Federal Communications Commission (FCC)This device complies with Part 15 of FCC Rules. Operation issubject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference that may cause undesired operation.Europe - R&TTE DirectiveThis device complies with the specifications listed below• EN 301-489 General EMC requirements for Radio equipment.• EN 300-328 Technical requirements for Radio equipment.• EN 60950 Safety Requirements for Radio equipmentWLAN 11g USB Adapter is limited in Ch1~Ch11 by specified fireware controled in U.S.A.
INTRODUCTIONThank you for your purchase of the WLAN Mini USB Adapter.Featuring wireless technology, this wireless networking solution hasbeen designed for both large and small businesses, and it is scalableso that you can easily add more users and new network featuresdepending on your business scale.FEATURESSupport Microsoft Windows 98SE, Me, 2000 and XP.Operating distance of up to 300 meters in free space.1Mbps, 2Mbps, 5.5Mbps, 11Mbps selectable Data Rate.Support USB 1.1 interface.64-bit or 128-bit WEP (Wired Equivalent Privacy).2.400GHz ~ 2.4835GHz unlicensed ISM Frequency Band.DSSS (Direct Sequence Spread Spectrum).Modulation Method : DQPSK / DBPSK / CCK.Easy operation and setting up.SYSTEM REQUIREMENTSWindows System : Windows 98SE, Me, 2000 or XP.PCs must have a device driver installed. It allows you to commu-nicate with WLAN Mini USB Adapter.1
2BEFORE YOU START1. Confirm Box ContentsCONNECTING YOUR WLAN USB ADAPTER TO PCQuick Start GuideConnect your WLAN USB dongle to yourPC.Install driver.GETTING TO KNOW WIRELESS LAN USB ADAPTERLEDLED turns on when POWER is applied to the WLAN Mini USB Adapter.LED is blinking when PC is sending data through WLAN Mini USBAdapter.Driver CDWireless LAN Adapter
WIRELESS LAN BASICSWireless LAN network defined by IEEE 802.11b/g standard committeecould be configured as :Ad Hoc wireless LAN, orInfrastructure wireless LAN.Ad Hoc network is a group of PCs installed with wireless LAN cards, thisgroup of PCs is called a BSS (Basic Service Set). PCs in this group can usetheir wireless LAN cards to communicate with each other, but can notconnect to the Internet.The most obvious difference between Infrastructure wireless networkand Ad Hoc wireless network is that the PCs in Infrastructure wirelessnetwork can access the resource in the Internet through Access Point.Depending on your requirement, you can easily set up your PC’snetwork to be a “Ad Hoc” or “Infrastructure” wireless network. Gener-ally speaking, if in your network, there is an Access Point in it, we recom-mend you to set your network as an “Infrastructure”, so it can connect tothe Internet.3Ad Hoc Wireless Network Infrastructure Wireless NetworkSTA 1STA 2STA 3
IP ADDRESSTo use the WLAN Mini USB Adapter with a computing device, the WLANMini USB Adapter must be equipped with an USB 1.1 or 2.0 Interface. Alldrivers and supporting software for the WLAN Mini USB Adapter must beinstalled and configured first.Ask your system administrator for the following information, which youmay need to provide during driver installation :Your Wireless Client Name.Your Wireless SSID.Your computer’s unique client name and workgroup name.For your network account, your user name and password.Your IP address, gateway address, and subnet mask if you’re notusing a DHCP server.Any computer on a network is identified by a unique network address.There are two methods to assign a network address to a computer on aTCP/IP network :Static IP addressing.Dynamic IP addressing (DHCP).In network with static IP addressing, the network administrator manuallyassigns an IP address to each computer. Once a static IP address isassigned, a computer uses the same IP address every time it reboots andlogs on to the network. You may manually change the IP address in theNetwork Properties dialog box. Network using static IP address is easy toset up and do not require additional network management software.In network with dynamic IP addressing, a DHCP server in the networkdynamically assigns IP addresses to all clients every time they log on tothe network. Network using dynamic IP address requires setting up andrunning a DHCP Server.4
The installation & driver CD will automatically activate the autoruninstallation program after you insert the disk into your CD drive.Step 1 :Insert the installation & driverDC into your CD-ROM.Step 2 :Click Next to continue.Step 3 :Click Next to install at the desig-nated folder. Or, click “Browse”to select different folder. INSTALL DRIVER / UTILITY5
Step 4 :Start copying files until it fin-ishes the installation.Step 5 :Click Finish to completeinstallation.Step 6 :After finished install driver and utility on your system, plug the USBadapter into the USB port of your PC. Windows XP/2000 will automati-cally detect the USB Adapter.6
WIRELESS NETWORK CONFIGURATIONWLAN USB Adapter uses its own management software. All functionscontrolled by users are provided by this application. When you insert theWLAN USB Adapter into the USB port of your PC, a new icon shouldappear in the Windows System Tray automatically.If the icon is in red, it means that WLAN USB Adapter configuration isinvalid or incomplete. Double click on that icon and the configurationwindow will pop up as shown below. It shows the SSID of availablenetwork. Once a network is chosen, the signal strength and link qualityare displayed.The Link Quality and Signal Strength bar chart is only active when thenode is in Infrastructure Mode. The bar graph displays the quality andstrength of the link between the node and its Access Point. Link Qualityis a measurement of receiving and transmitting performances over theradio.Tx/Rx Frame displays the instantaneous wireless Transmit and Receivethroughput in bytes per second. These values are updated every twoseconds.The Configuration Tool containsseveral fields where operatingparameters of the driver can beviewed or changed. Changes toany of the parameters in thispanel can be applied to the driverwithout a need to restart thecomputer.Current Network Informationdisplays the current networkconfiguration. If you want tochange network configuration, click “More Setting”.7
5.1 GENERAL CONNECTION SETTINGIn this panel, you can modify thegeneral network connection setting,enable/disable the WEP, load/modify profile and other setting.Through this control panel, you willbe able to access the corporatewireless LAN or hot spots such ashotel, airport, and conference hall.Click “Change” to start input ofsettings. The settings include :SSID.Network Type.Transmit Rate.Encryption.Authentication Mode.When settings are input, click “Ap-ply” to confirm changes of them.8
5.2 WEP ENCRYPTION KEY SETTINGYou may want an additional mea-sure of security on your wirelessnetwork, which can be achieved byusing WEP (Wired EquivalentPrivacy) encryption. WEP encryptseach frame transmitted from theradio using one of the Keys enteredin this panel.When an encrypted frame is re-ceived it will only be accepted if itdecrypts correctly. This will onlyhappen if the receiver has the sameWEP Key used by the transmitter.The default state in EncryptionSetting is WEP disabled. Check “Enable WEP” to enable the encryption.For more WEP key setting, Click “WEP Encryption Key Setting”.Three authentication modes areavailable: Open System, Shared Keyand Auto. The Open System usesdefault key to authenticate thestation and Access Point. Once bothparties are authenticated, thestation is allowed to send and re-ceive data from the network.However, the data are notencrypted.In Shared Key system, the station and Access Point are authenticatedeach other. The data frame is also encrypted by the WEP key.In Auto Mode, the Access Point takes control of network security settingand station will follow the setting required from AP.Click the “close box” at the upper right hand corner to return to Con-figuration Tool.9
WPA (Wi-Fi Protected Access) is asecurity technology for wirelessnetworks. WPA improves on theauthentication and encryption fea-tures of WEP (Wired EquivalentPrivacy).To improve data encryption, WPAutilizes its Temporal Key IntegrityProtocol (TKIP). TKIP provides im-portant data encryption enhance-ments including a per-packet keymixing function, a message integ-rity check (MIC, named Michael), anextended initialization vector (IV)with sequencing rules, and a re-keying mechanism.WPA Pre-Shared Key (WPA-PSK) is asimplified but still powerful form ofWPA most suitable for home Wi-Finetworking. To use WPA-PSK, aperson sets a static key or“passphrase” as with WEP. But,using TKIP, WPA-PSK automaticallychanges the keys at a preset timeinterval, making it much moredifficult for hackers to find andexploit them.The pre-shared key is consisting ofalpha-numeric characters includingpunctuation and spaces between 8and 63 characters long.Wirelessclients are only required to enterthe pre-shared key.If the pre-shared keys match, secure wireless communications can begin to takeplace.For more WPA setting, Click “WPA Encryption Setting”5.3 WPA ENCRYPTION SETTING10
Each profile represents specific settings of the USB adapter. You can setthe settings for each profile. Next time when you want to change theUSB adapter settings, you can just select the profile you want to use.5.4 PROFILE11
5.5 ADVANCED SETTINGClick “Advanced Setting” to select power consumption setting that has 3different modes. In this panel, you can select different user interfaceand country roaming.It also allows you to set the threshold of fragmentation and RTS/CTS.12
Click “Information” and the pop-up window will show the Driver Version,Utility Version, MAC address of this USB adapter and so on.5.6 SYSTEM INFORMATION13
14 TECHNICAL SPECIFICATIONSProduct Name 11b+g WLAN USB AdapterStandard IEEE802.11b/gFrequency Band 2.400GHz ~ 2.4835GHz unlicensed ISM band802.11b : QPSK/BPSK/CCK802.11g : OFDMData Rate 54/48/36/24/18/12/11/9/6/5.5/2/1MbpsAd hocInfrastructure (Access Points is needed)Transmitter Output Power < 10.48 dBmOperating at 11Mbps: @ –80dBmOperating at 54Mbps: @ –70dBmOperating Range 30 to 200 m, depending on surrounding environmentAntenna Chip antennaSecurity 64-bit, 128-bit or 256-bit WEP (Wired Equivalent Privacy);WPA (Wi-Fi Protected Access)I/O Interface USB 2.0/1.1LED Link/ActiveOperating system supported Windows 98Se, Me, 2000 and XPManagement Windows-based configuration utility and status monitoringRegulation FCC for North AmericaCE/ETSI for EuropeanDimension 58(L) x 23(W) x 9(H) mmWeight 9.6 gOperating Temperature 0 ~ 50 ℃Storage Temperature -20 ~ 70 ℃Humidity 5 ~ 90% (non-condensing)M od ula t io n me t ho dOperation modeReceive Sensitivity
TROUBLESHOOTINGSymptom :The LED is off.Remedy :Make sure the PC Card is inserted properly. Otherwise contact yourvendor.Symptom :The LED is always on not blinking.Remedy :Make sure that you have installed the driver from attached CD. Otherwisecontact your vendor.Symptom :The LED is blinking but the PC Card icon does not appear in your icon tray.Remedy :Make sure that you have installed the Utility from the attached CD.Symptom :The PC Card is linking, but can’t share files with others.Remedy :Make sure the file and printer sharing function is enabled. You canenable the function by checking the icon of My Computer -> ControlPanel -> Network -> file and printer sharing -> I want to be able to giveothers to access to my files.Symptom :Slow or poor performance.Remedy :Try to select another channel for the communicating group or move yourdevice closer to the Access Point.15
GLOSSARYIEEE 802.11 StandardThe IEEE 802.11 Wireless LAN standards subcommittee, which is formu-lating a standard for the industry.Access PointAn internetworking device that seamlessly connects wired and wirelessnetworks together.Ad HocAn Ad Hoc wireless LAN is a group of computers, each with a WLANadapter, connected as an independent wireless LAN. Ad Hoc wireless LANis applicable at a departmental scale for a branch or SOHO operation.BSSIDA specific Ad Hoc LAN is called a Basic Service Set (BSS). Computers in aBSS must be configured with the same BSSID.DHCPDynamic Host Configuration Protocol - a method in which IP addresses areassigned by server dynamically to clients on the network. DHCP is used forDynamic IP Addressing and requires a dedicated DHCP server on thenetwork.Direct Sequence Spread SpectrumThis is the method the wireless cards use to transmit data over the fre-quency spectrum. The other method is frequency hopping. Direct se-quence spreads the data over one frequency range (channel) while fre-quency hopping jumps from one narrow frequency band to another manytimes per second.ESSIDAn Infrastructure configuration could also support roaming capability formobile workers. More than one BSS can be configured as an ExtendedService Set (ESS). Users within an ESS could roam freely between BSSswhile served as a continuous connection to the network wireless stationsand Access Points within an ESS must be configured with the same ESSIDand the same radio channel.16
EthernetEthernet is a 10/100Mbps network that runs over dedicated home/officewiring. Users must be wired to the network at all times to gain access.GatewayA gateway is a hardware and software device that connects two dissimilarsystems, such as a LAN and a mainframe. In Internet terminology, a gate-way is another name for a router. Generally a gateway is used as a funnelfor all traffic to the Internet.IEEEInstitute of Electrical and Electronics EngineersInfrastructureAn integrated wireless and wired LAN is called an Infrastructureconfiguration. Infrastructure is applicable to enterprise scale for wirelessaccess to central database, or wireless application for mobile workers.ISM BandThe FCC and their counterparts outside of the U.S. have set aside band-width for unlicensed use in the so-called ISM (Industrial, Scientific andMedical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is beingmade available worldwide. This presents a truly revolutionary opportunityto place convenient high-speed wireless capabilities in the hands of usersaround the globe.Local Area Network (LAN)A LAN is a group of computers, each equipped with the appropriate net-work adapter card connected by cable/air, that share applications, data,and peripherals. All connections are made via cable or wireless media,but a LAN does not use telephone services. It typically spans a singlebuilding or campus.NetworkA network is a system of computers that is connected. Data, files, andmessages can be transmitted over this network. Networks may be local orwide area networks.17
ProtocolA protocol is a standardized set of rules that specify how a conversationis to take place, including the format, timing, sequencing and/ or errorchecking.RoamingIn an infrastructure network, this is when a wireless PC moves out ofrange of the previously connected access point and connects to a newlyconnected access point. Throughout the network environment whereaccess point is deployed, PCs can always be connected regardless ofwhere they are located or roam.SSIDA Network ID unique to a network. Only clients and Access Points thatshare the same SSID are able to communicate with each other. This stringis case-sensitive.Simple Network Management Protocol (SNMP)Simple Network Management Protocol is the network management proto-col of TCP/IP. In SNMP, agents-which can be hardware as well as soft-ware-monitor the activity in the various devices on the network andreport to the network console workstation. Control information abouteach device is maintained in a structure known as a management informa-tion block.Static IP AddressingA method of assigning IP addresses to clients on the network. In networkswith Static IP address, the network administrator manually assigns an IPaddress to each computer. Once a Static IP address is assigned, a com-puter uses the same IP address every time it reboots and logs on to thenetwork, unless it is manually changed.Temporal Key Integrity Protocol (TKIP)The Temporal Key Integrity Protocol, pronounced tee-kip, is part of theIEEE 802.11i encryption standard for wireless LANs. TKIP is the nextgeneration of WEP, the Wired Equivalency Protocol, which is used tosecure 802.11 wireless LANs. TKIP provides per-packet key mixing, amessage integrity check and a re-keying mechanism, thus fixing theflaws of WEP.18
Transmission Control Protocol / Internet Protocol (TCP/IP)TCP/IP is the protocol suite developed by the Advanced ResearchProjects Agency (ARPA). It is widely used in corporate Internet works,because of its superior design for WANs. TCP governs how packet issequenced for transmission the network. The term “TCP/IP” is oftenused generically to refer to the entire suite of related protocols.Transmit / ReceiveThe wireless throughput in Bytes per second averaged over two seconds.Wi-Fi AllianceThe Wi-Fi Alliance is a nonprofit international association formed in 1999to certify interoperability of wireless Local Area Network products basedon IEEE 802.11 specification. The goal of the Wi-Fi Alliance’s members isto enhance the user experience through product interoperability. Theorganization is formerly known as WECA.Wi-Fi Protected Access (WPA)The Wi-Fi Alliance put together WPA as a data encryption method for802.11 wireless LANs. WPA is an industry-supported, pre-standard ver-sion of 802.11i utilizing the Temporal Key Integrity Protocol (TKIP),which fixes the problems of WEP, including using dynamic keys.Wide Area Network (WAN)A WAN consists of multiple LANs that are tied together via telephoneservices and / or fiber optic cabling. WANs may span a city, a state, acountry, or even the world.Wired Equivalent Privacy (WEP)Now widely recognized as flawed, WEP was a data encryption methodused to protect the transmission between 802.11 wireless clients andAPs. However, it used the same key among all communicating devices.WEP’s problems are well-known, including an insufficient key length andno automated method for distributing the keys. WEP can be easilycracked in a couple of hours with off-the-shelf tools.19
Wireless LAN (WLAN)A wireless LAN does not use cable to transmit signals, but rather usesradio or infrared to transmit packets through the air. Radio Frequency(RF) and infrared are the commonly used types of wireless transmission.Most wireless LANs use spread spectrum technology. It offers limitedbandwidth, usually under 11Mbps, and users share the bandwidth withother devices in the spectrum; however, users can operate a spreadspectrum device without licensing from the Federal CommunicationsCommission (FCC).20
One Year Limited WarrantyThis device is guaranteed against manufacturing defectsfor one full year from the original date of purchase.This warranty is valid at the time of purchase and is non-transferable.This warranty must be presented to the service facilitybefore any repair can be made.Sales slip or other authentic evidence is required to validate war-ranty.Damage caused by accident, misuse, abuse, improper storage,and/or uncertified repairs is not covered by this warranty.All mail or transportation costs including insurance are at the ex-pense of the owner.Do not send any product to service center for warranty without aRMA(Return Merchandise Authorization) and proof of purchase. Ensurea trackable method of delivery is used (keep tracking number).Warranty is valid only in the country of purchase.We assumes no liability that may result directly or indirectlyfrom the use or misuse of these products.IMPORTANT" This warranty will be voided if the device is tampered with, improperlyserviced, or the security seals are broken or removed"21

Navigation menu