USERS MANUAL 1
Please read this user’s guide before
installing, setting up and using your new product
www.radioshack.com
To power your slider, you will need one 9V battery
for the transmitter and six AA batteries for the
slider. None are supplied, but all are available at
your local RadioShack or online at
www.radioshack.com.
in the transmitter
• Dispose of old batteries promptly and properly. Do not burn or bury batteries.
• Use only fresh batteries of the required size and recommended type.
• Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or
rechargeable batteries of different capacities.
• If you do not plan to use the toy for several days, remove the batteries. Batteries can leak chemicals that
can damage electronic parts.
• Batteries purchased for use in this toy may pose a hazard to children. Please check the safety notice
supplied with batteries before use.
Note: Actual product may vary from the images
found in this document. Photos not to scale.
Thank you for purchasing your Micro Slider from
RadioShack. This tiny vehicle will dazzle your
friends because of all the cool stunts it can do. The
slider is available in two frequencies (27 and 49
MHz) so that you can race other radio-controlled
vehicles.
Micro Slider transmitter
charger user’s guide
60-4394
micro slider
in the charger
1. Remove the charger’s battery compartment
cover. Replace
when fi nished.
NOTE
2. Place the 9 volt
battery in the
compartment
as indicated
by the polarity
symbols
(+ and -).
1. Remove the
cover. Replace
when fi nished.
When the transmitter’s range
decreases, replace its battery.
2. Install six AA
batteries into
charger’s battery
compartment as
indicated by the
polarity symbols
(+ and -).
Micro
Slider
Transmitter
Charger
©2004 RadioShack Corporation.
All rights reserved. RadioShack and
RadioShack.com are trademarks
used by RadioShack Corporation.
60-4394
07A04
Printed in China
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult your local RadioShack store or an experienced radio/TV technician
for help.
If you cannot eliminate the interference, the FCC requires that you stop
using your slider. Changes or modifi cations not expressly approved by
RadioShack may cause interference and void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Product Micro Slider
Model 60-4394
Responsible Party
RadioShack
100 Throckmorton
Fort Worth,
TX 76102
Phone 817-415-3200
This product is warranted by RadioShack against manufacturing defects in ma-
terial and workmanship under normal use for ninety (90) days from the date of
purchase from RadioShack company-owned stores and authorized RadioShack
franchisees and dealers. For complete warranty details and exclusions, check
with your local RadioShack store.
RadioShack Customer Relations
200 Taylor Street, 6th Floor, Fort Worth, TX 76102 04/04
The EPA certifi ed RBRC® Battery Recycling
Seal on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack is voluntarily
participating in an industry program to collect
and recycle these batteries at the end of their useful
life, when taken out of service in the United States
or Canada. The RBRC program provides a convenient
alternative to placing used Ni-Cd batteries into the trash
or the municipal waste stream, which may be illegal in
your area. Please call 1-800-THE-SHACK
(1-800-843-7422) for information on Ni-Cd battery
recycling and disposal bans/restrictions in your area.
RadioShack’s involvement in this program is part of the
company’s commitment to preserving our environment
and conserving our natural resources.
• Keep your slider, charger, and transmitter dry. If they
get wet, wipe them dry immediately.
• Use and store the slider, charger, and transmitter only
in room temperature environments.
• Handle the slider, transmitter, and charger carefully.
Do not drop them.
• Keep the slider, charger, and transmitter away from
dust and dirt, and wipe them with a damp cloth
occasionally to keep them looking new.
• Do not play with your vehicle in the street.
• Your slider may perform differently on different types
of surfaces.
• Do not play with the slider on hairy or carpeted
surfaces, as hair or lint can damage the wheel gears.
• If your slider is not performing as it should, take it to
your local RadioShack store for assistance.
• Driving your slider for long periods of time can
generate a high heat level, which causes wear and
tear on the motor. To help keep heat levels down,
when your vehicle’s battery power dies, let it cool for
at least 10 minutes before installing new batteries.
• Do not touch the motor or batteries immediately
after using the slider, as they may become hot during
use.
• If your slider’s motor runs, but does not respond to
the transmitter, move closer to the vehicle and try
again.
• If someone uses a CB nearby, it might interfere with
the control of your slider. If this happens, move the
vehicle away from the CB.
• You cannot operate your slider near devices with
transmitters that use the same frequency as your
vehicle (27 MHz or 49 MHz). Check the box to see
which frequency you have.
1. Turn off the vehicle and plug it into the charger
as indicated.
2. Press the charging button and make sure the
LED indicator lights up red, indicating it is
charging.
3. Unplug the vehicle when the LED turns off,
indicating charging is complete.
Charge time is about 5 minutes.
Run time of the vehicle is about 5
minutes between charges.
Never recharge your vehicle without
completely discharging it fi rst. This can
damage the slider.
NOTE
Charging
Button
LED
Indicator
ON/OFF
Switch
getting started
1. Fully extend the transmitter’s antenna.
2. Slide the ON/OFF switch on the transmitter and
slider to ON.
3. Use the controls on the transmitter to drive the
slider.
using your controls
1. Press A to move forward in a straight line
().
2. Press B to move backward in a straight line
().
3. Press C to rotate counter clockwise ().
4. Press D to rotate clockwise ().
5. Press A and C together to drive forward in
a clockwise circle.
6. Press A and D together to drive forward in
a counter clockwise circle.
7. Press B and C together to drive backward
in a counter clockwise circle.
8. Press B and D together to drive backward
in a clockwise circle.
9. Use the E and F buttons to fl ip the wheels
around to move the slider sideways and
around in circles.
Try your own combination of buttons
to make up your own stunts!
ON/OFF
Switch
D
Button
A
Button
B
Button
C
Button
E
Button
F
Button
Antenna
NOTE