CHANG SHIN INFOTEL WKEY-2000 WIRELESS IDENTIFICATION KEY SYSTEM WITH ZIGBEE User Manual User s manual
CHANG SHIN INFOTEL CO.,LTD WIRELESS IDENTIFICATION KEY SYSTEM WITH ZIGBEE User s manual
User Manual
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 1
WKEY-2000 Users’ Manual
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 2
Contents
1. Product overview …………………………………………………………………………………….3
2. Product mix ……………………………………………………………………………………………4
3. How to use WKey-2000 …………………………………………………………………………..5
4. System configuration ………………………………………………………………………………7
5. WKey-2000 Specifications ………………………………………………………………………..8
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 3
1. Product overview
WKey-2000 is a wireless authentication key that you wirelessly communicate with each other
in 2.4GHz. It is used as a key of access control systems as the product which satisfies users’
convenience and security. As it doesn’t require users’ authentication behaviors like RF-ID or
finer scan, but is automatically authenticated, it is the next generation access device that
convenience was drastically improved.
The external appearance of WKey-2000 made by CSINFOTEL is as follow:
[Figure 1] WKey-2000
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 4
2. Product mix
WKey-2000 consists of the following products:
- A finished product of WKey-2000
- Three coin batteries are included.
Please see [Figure 2].
[Figure 2] WKey-2000
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 5
3. How to use WKey-2000
[Figure 3] WKey-2000
WKey-2000’s composition is shown in [Figure 4].
Three coin batteries are used in Wkey-2000 of this company. You can use it for about a week
when you operate Power On (Sleep Mode, Interval Time 5sec).
How to use the user button and status LED is as follow: You can select use by using the
Button. And if you press the Button for more than three seconds, Red LED can change the
operational status of WKey-2000. If Red LED flickers twice, the power is switched on and
Green LED flickers by the set cycle (Default 5 sec.). At this moment, you can use the wireless
access authentication function.
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 6
If you again press the Button for more than three seconds while the power is switched on,
Red LED flickers once and the power is switched off. When the power is switched off, the
wireless access authentication function cannot be used and battery consumption can
remarkably be reduced.
Therefore, it is recommended to use the product by turning off the power in advance in
places that access authentication is not required.
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 7
4. System configuration
[Figure 3] WKey-2000’s system configuration
WKey-2000’s system configuration is shown in [Figure 3]. WKey-2000 wirelessly communicates
with SG-7000. And SG-7000 communicates with it by using Manager/Server and Ethernet.
For the contents related to SG-7000 and Manager/Server, please see each manual.
W-KEY Users’ Manual
http://www.csinfotel.com/ PAGE 8
5. WKey-2000 specifications
Item Specifications
MCU 16 bit Microprocessor
RF communication band 2.4GHz ~ 2.4835 GHz
Data-rate 250Kbps
IEEE Standard 802.15.4 2003
Battery LITHIUM Battery(CR2032) x 3 / 3Vdc, 0.3A
Workable temperature -20℃ ~ 50℃
15.21 You are cautioned that changes or modifications not expressly approved
by the part responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may
cause undesired operation of the device.
15.105(b) This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT!!