CLEVO M72S Notebook User Manual I

CLEVO Co. Notebook Users Manual I

Contents

Users Manual I

IPrefaceNoticeThe company reserves the right to revise this publication or to change its contents without notice. Informationcontained herein is for reference only and does not constitute a commitment on the part of the manufacturer orany subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appearin this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)of this publication.This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans-mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creatorsof this publication, except for copies kept by the user for backup purposes.Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade-marks of their respective companies. They are mentioned for identification purposes only and are not intendedas an endorsement of that product or its manufacturer.©May 2007TrademarksThis product incorporates copyright protection technology that is protected by method claims of certain U.S. pat-ents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use ofthis copyright protection technology must be authorized by Macrovision Corporation, and is intended for homeor other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineer-ing or disassembly is prohibited.Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.
IIPrefaceFCC Statement(Federal Communications Commission)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Re orient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the service representative or an experienced radio/TV technician for help.WarningUse only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex-pressly approved by the manufacturer for compliance with the above standards could void your authority to operate theequipment.If your purchase option includes both Wireless LAN and 3.5G modules, then the appropriate antennas will be installed. Notethat In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate inconjunction with any other antenna or transmitter.
IIIPrefaceIMPORTANT SAFETY INSTRUCTIONSFollow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injuryto persons when using any electrical equipment:1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.3. Do not use the telephone to report a gas leak in the vicinity of the leak.4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.5. This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19V, 3.42A (65 Watts) minimum AC/DC Adapter.CAUTIONAlways disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER, TELECOMMUNICATION LINE CORDThis Computer’s Optical Device is a Laser Class 1 Product
IVPrefaceInstructions for Care and OperationThe notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam-aged.Do not expose the computer to any shock or vibration. Do not place it on an unstable surface. Do not place anything heavy on the computer.Do not expose it to excessive heat or direct sunlight. Do not leave it in a place where foreign matter or mois-ture may affect the system.Don’t use or store the com-puter in a humid environment. Do not place the computer on any surface that will block the Vents/Fan Intakes.
VPreface3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.5. Take care when using peripheral devices.Do not turn off the power until you properly shut down all programs.Do not turn off any peripheral devices when the computer is on.Do not disassemble the com-puter by yourself. Perform routine maintenance on your computer.Use only approved brands of peripherals. Unplug the power cord before attaching peripheral devices.
VIPrefacePower SafetyThe computer has specific power requirements:• Only use a power adapter approved for use with this computer.• Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.• Before cleaning the computer, make sure it is disconnected from any external power sup-plies (i.e. AC/DC adapter or car adapter).Do not plug in the power cord if you are wet. Do not use the power cord if it is broken. Do not place heavy objects on the power cord.Power Safety WarningBefore you undertakeany upgrade proce-dures, make sure thatyou have turned off thepower, and discon-nected all peripheralsand cables (includingtelephone lines). It isadvisable to also re-move your battery inorder to prevent acci-dentally turning themachine on.
VIIPrefaceBattery Precautions• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.• Do not remove any batteries from the computer while it is powered on.• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qual-ified service personnel.• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.• Keep the battery away from metal appliances.• Affix tape to the battery contacts before disposing of the battery.• Do not touch the battery contacts with your hands or metal objects.Battery Disposal & CautionThe product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check withyour local solid waste officials for details in your area for recycling options or proper disposal.Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by themanufacturer. Discard used battery according to the manufacturer’s instructions.
VIIIPrefaceCleaningDo not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.ServicingDo not attempt to service the computer yourself. Doing so may violate your warranty and expose you and thecomputer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from thepower supply. Then refer servicing to qualified service personnel under any of the following conditions:• When the power cord or AC/DC adapter is damaged or frayed.• If the computer has been exposed to rain or other liquids.• If the computer does not work normally when you follow the operating instructions.• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).• If there is an unusual odor, heat or smoke coming from your computer.Removal WarningWhen removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) andscrew(s) before turning the computer on.
IXPrefaceTravel ConsiderationsPackingAs you get ready for your trip, run through this list to make sure the system is ready to go:1. Check that the battery pack and any spares are fully charged.2. Power off the computer and peripherals.3. Close the display panel and make sure it’s latched.4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. 5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.6. Put the notebook in its carrying bag and secure it with the bag’s straps.7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables.8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hard-ware and software. Make sure your documents are prepared.Power Off Before TravelingMake sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting anotebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prevent yourcomputer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
XPrefaceOn the RoadIn addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,keep these points in mind:Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is verycommon. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knock-ing the computer against hard objects.Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com-puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer anddisks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:Some airports also scan luggage with these devices.Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, makesure it’s secure. Contents may shift and/or fall out when the compartment is opened.Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)charged.Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.Wait a few minutes before turning it on so that any moisture can evaporate.
XIPrefaceDeveloping Good Work HabitsDeveloping good work habits is important if you need to work in front of the computer for long periods of time.Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists orother joints. The following are some tips to reduce the strain:• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.• Use a chair with a back and adjust it to support your lower back comfortably.• Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.• Take periodic breaks if you are using the computer for long periods of time.Remember to:• Alter your posture frequently.• Stretch and exercise your body several times a day.• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XIIPrefaceLightingProper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck andshoulders.• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.• Position the display directly in front of you at a comfortable viewing distance.• Adjust the display-viewing angle to find the best position.LCD Screen CareTo prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen foran extended period of time) take the following precautions:• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).• Rotate desktop background images every few days.• Turn the monitor off when the system is not in use.
XVPrefaceContentsNotice .................................................................................IFCC Statement .............................................................IIInstructions for Care and Operation ..........................IVPower Safety ..............................................................VIBattery Precautions ...................................................VIICleaning .................................................................. VIIIServicing ................................................................. VIIITravel Considerations ................................................IXQuick Start GuideOverview ........................................................................1-1Advanced Users ...........................................................1-2Beginners and Not-So-Advanced Users ......................1-2Warning Boxes ............................................................1-2Not Included ................................................................1-3System Software ..........................................................1-4System Startup ...............................................................1-5System Map: LCD Panel Open ......................................1-6LED Indicators ............................................................1-7Hot Key Buttons & Keyboard .......................................1-8Keyboard ........................................................................1-9Function Keys ..............................................................1-10System Map: Front & Rear Views ...............................1-11System Map: Left & Right Views ...............................1-12System Map: Bottom View ..........................................1-14Windows Vista Start Menu & Control Panel ...............1-15Video Features .............................................................1-16Power Options ..............................................................1-18Features & ComponentsOverview ........................................................................2-1Hard Disk Drive .............................................................2-2Optical (CD/DVD) Device ............................................2-3Loading Discs ..............................................................2-3Handling CDs or DVDs ...............................................2-4DVD Regional Codes ..................................................2-57-in-1 Card Reader .........................................................2-6ExpressCard Slot ............................................................2-7Inserting and Removing ExpressCards ........................2-7TouchPad and Buttons/Mouse .......................................2-8Function/Hot Key Indicators .........................................2-9Audio Features .............................................................2-10Adding a Printer ...........................................................2-11USB Printer ..............................................................2-11Parallel Printer ..........................................................2-11
XVIPrefacePower ManagementOverview ........................................................................3-1The Power Sources ........................................................3-2AC/DC Adapter ...........................................................3-2Battery .........................................................................3-2Turning on the Computer ...............................................3-3Power Plans ...................................................................3-4Power-Saving States ......................................................3-6Sleep ...........................................................................3-6Hibernate ....................................................................3-7Shut Down ..................................................................3-7Configuring the Power Buttons .....................................3-8Resuming Operation ...................................................3-9Battery Information .....................................................3-10Battery Power ...........................................................3-10Conserving Battery Power .........................................3-11Battery Life ................................................................3-12New Battery ..............................................................3-12Recharging the Battery with the AC/DC Adapter .....3-12Proper handling of the Battery Pack .........................3-13Battery FAQ ..............................................................3-14Drivers & UtilitiesWhat to Install ................................................................4-1Module Driver Installation ..........................................4-1Driver Installation ..........................................................4-2Manual Driver Installation .........................................4-3Updating/Reinstalling Individual Drivers ...................4-4User Account Control (Win Vista) ..............................4-4Windows Security Message .........................................4-4New Hardware Found ..................................................4-4Driver Installation Procedure .......................................4-5Video ..........................................................................4-5Audio ..........................................................................4-5Modem ........................................................................4-5LAN ............................................................................4-5TouchPad ....................................................................4-6CardReader .................................................................4-6Hot Key ......................................................................4-6PC Camera Module ....................................................4-6Wireless LAN Module ...............................................4-6Bluetooth Module .......................................................4-63.5G Module ...............................................................4-6Fingerprint Reader Module ........................................4-6BIOS UtilitiesOverview ........................................................................5-1The Power-On Self Test (POST) ...................................5-2Failing the POST .........................................................5-3Fatal Errors .................................................................5-3
XVIIPrefaceNon-Fatal Errors .........................................................5-3The Setup Program ........................................................5-4Entering Setup .............................................................5-4Setup Screens ...............................................................5-5Main Menu .....................................................................5-6System Time & Date (Main Menu) ...............................5-6IDE Channel 0 Master (Main Menu) .............................5-7SATA Port 1 (Main Menu) ............................................5-7System/Extended Memory: (Main Menu) .....................5-7Advanced Menu .............................................................5-8Installed O/S: (Advanced Menu) ...................................5-8IDE PATA+SATA ID Control (Advanced Menu) ........5-9Boot-time Diagnostic Screen: (Advanced Menu) ..........5-9Security Menu ..............................................................5-10Set Supervisor Password (Security Menu) ..................5-10Password on boot: (Security Menu) ............................5-11Fixed disk boot sector: (Security Menu) .....................5-11Boot Menu ...................................................................5-12Exit Menu ....................................................................5-13Upgrading The ComputerOverview ........................................................................6-1When Not to Upgrade ..................................................6-2Removing the Battery ....................................................6-3Upgrading the Hard Disk Drive .....................................6-4Upgrading the Optical (CD/DVD) Device ....................6-6Upgrading the System Memory (RAM) ........................6-7Upgrading the Processor ..............................................6-10Modules & OptionsOverview ........................................................................7-1PC Camera Module ........................................................7-2802.11 b/g USB WLAN Module .................................7-11Bluetooth Module ........................................................7-163.5G Module ................................................................7-20Fingerprint Reader Module ..........................................7-28TroubleshootingOverview ........................................................................8-1Basic Hints and Tips ......................................................8-2Backup and General Maintenance .................................8-3Viruses ...........................................................................8-4Upgrading and Adding New Hardware/Software ..........8-5Problems and Possible Solutions ...................................8-7Interface (Ports & Jacks)Notebook Ports and Jacks .............................................A-2SIS Video Driver Installation .......................................B-1Video .........................................................................B-1Video Memory ...........................................................B-1
XVIIIPrefaceSIS VGA Control Center .............................................. B-2Attaching Other Displays ............................................. B-5To Enable a Display Setting Mode ...............................D-7SpecificationsProcessor .......................................................................C-1Core Logic .................................................................... C-2LCD .............................................................................. C-2Memory ......................................................................... C-2Video Adapter ............................................................... C-2Security ......................................................................... C-2BIOS ............................................................................. C-2Storage .......................................................................... C-2Audio ............................................................................ C-2Keyboard & Pointing Device ........................................ C-3Interface ........................................................................ C-3Card Reader .................................................................. C-3ExpressCard Slot .......................................................... C-3Communication ............................................................. C-3Power Management ...................................................... C-4Power ............................................................................ C-4Battery ........................................................................... C-4Environmental Spec ......................................................C-4Dimensions ...................................................................C-4& Weight ...................................................................... C-4Optional ........................................................................C-5Windows XP InformationDVD Regional Codes ...................................................D-2Windows XP Start Menu & Control Panel ...................D-3TouchPad and Buttons/Mouse ......................................D-4Function Keys ...............................................................D-5Audio Features ..............................................................D-6Video Features ..............................................................D-7Attaching Other Displays ............................................D-11Power Management Features ......................................D-13Advanced Configuration and Power Interface .........D-13The Power Sources .....................................................D-14AC/DC Adapter ........................................................D-14Battery ......................................................................D-14Turning on the Computer ............................................D-15Power Schemes ...........................................................D-16System Power Options ................................................D-18Hibernate Mode vs. Shutdown .................................D-18Stand by Mode vs. Hibernate Mode .........................D-18Configuring the Power Button ....................................D-20Battery Information .....................................................D-21Recharging the Battery with the AC/DC Adapter ....D-22Battery FAQ .............................................................D-24Driver Installation .......................................................D-25
XIXPrefaceDriver Installation Procedure ...................................D-28PC Camera Module .....................................................D-30802.11 b/g USB WLAN Module ................................D-37Bluetooth Module .......................................................D-393.5G Module ...............................................................D-43Fingerprint Reader ......................................................D-44
Overview 1 - 1Quick Start Guide 1Chapter 1: Quick Start GuideOverviewThis Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around thecomputer and to getting your system started. The remainder of the manual covers the following:•Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, 7-in-1 card reader, ExpressCard/34/54), TouchPad & Mouse, Function/Hot Keys, Quick Buttons, Audio & Printer.•Chapter 3 The computer’s power saving options.•Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.•Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).•Chapter 6 Instructions for upgrading your computer.•Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth and PC Camera modules (some of which may be optional depending on your purchase configuration).•Chapter 8 A troubleshooting guide.•Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.•Appendix B Information on the SIS Video driver controls.•Appendix C he computer’s specification.•Appendix D Information on the Windows XP OS.
1 - 2 OverviewQuick Start Guide1Advanced UsersIf you are an advanced user you may skip over most of this Quick Start Guide. However you may find it usefulto refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” onpage 6 - 1 in the User’s Manual. You may also find the notes marked with a  of interest to you.Beginners and Not-So-Advanced UsersIf you are new to computers (or do not have an advanced knowledge of them) thenthe information contained in this Quick Start Guide should be enough to get you upand running. Eventually you should try to look through all the documentation (moredetailed descriptions of the functions, setup and system controls are covered in theremainder of the User’s Manual), but do not worry if you do not understand every-thing the first time. Keep this manual nearby and refer to it to learn as you go. Youmay find it useful to refer to the notes marked with a  as indicated in the margin.For a more detailed description of any of the interface ports and jacks see “Interface(Ports & Jacks)” on page A - 1.Warning BoxesNo matter what your level please pay careful attention to the warning and safety information indicated by the symbol. Also please note the safety and handling instructions as indicated in the Preface.NotesCheck the light coloredboxes with the markabove to find detailed in-formation about the com-puter’s features.
Overview 1 - 3Quick Start Guide 1Not IncludedOperating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet anddatabase programs) have their own manuals, so please consult the appropriate manuals.DriversIf you are installing new system software, or are re-configuring your computer for a different system, you will need to installthe drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com-puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the orderlisted in. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed.If your system hasn’t been properly configured (your service representative may have already done that for you); refer toChapter 4 for installation instructions.Ports and JacksSee “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your com-puter to communicate with external devices, connect to the internet etc.
1 - 4 OverviewQuick Start Guide1System SoftwareYour computer may already come with system software pre-installed. Where this is not the case, or where youare re-configuring your computer for a different system, you will find the following operating systems are sup-ported.Table 1 - 1 - Model Differences*Note: For information on the Windows XP OS (specifically power, video and driver information) see “Win-dows XP Information” on page D - 1.Operating System & Version Supported Note*Windows XP Home or Professional Editions In order to run Windows XP without limitations or decreasedperformance, your computer requires a minimum 512MB ofsystem memory (RAM)Windows Vista (32-bit) Home Basic EditionIn order to run Windows Vista without limitations ordecreased performance, your computer requires a minimum1GB of system memory (RAM)
System Startup 1 - 5Quick Start Guide 1System Startup1. Remove all packing materials.2. Place the computer on a stable surface.3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.5. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.6. Adjust the LCD panel to a comfortable viewing angle.7. The LED indicators show the power and battery status of the computer.Figure 1 - 1 - AC/DC Adapter InShutdownNote that you should always shut your computer down by choosingthe Shut Down command from the Lock Button Menu in Win-dows Vista. This will help prevent hard disk or system problems.
1 - 6 System Map: LCD Panel OpenQuick Start Guide1System Map: LCD Panel OpenFigure 1 - 2LCD Panel Open1. Built-In PC Camera (Optional)2. LCD3. Speakers4. Power Button5. Hot Key Buttons6. LED Status Indicators7. Keyboard8. Touchpad & Buttons9. LED Power & Communication Indicators10. Fingerprint Module (Optional)11. Built-In Microphone251784693311Wireless Device Operation Aboard AircraftThe use of any portable electronictransmission devices aboard aircraft isusually prohibited. Make sure the mod-ule(s) are OFF if you are using thecomputer aboard aircraft.Use the key combinations to togglepower to the 3.5G/WLAN/Bluetoothmodules, and check the LED indicatoricon to see if the modules are poweredon or not (see Table 1 - 5, on page 1 -10/ Table 1 - 2, on page 1 - 7).6510
System Map: LCD Panel Open 1 - 7Quick Start Guide 1LED IndicatorsThe two sets of LED indicators (LED Status Indica-tors and LED Power & Communication Indicators)on the computer display helpful information about thecurrent status of the computer.Table 1 - 2 - LED Status Indicators Table 1 - 3 - LED Power & Communication IndicatorsIcon Color DescriptionGreen Silent Mode Activated (see over)Off Normal Mode Activated (see over)Green Hard Disk ActivityGreen Number Lock ActivatedGreen Caps Lock ActivatedGreen Scroll Lock Activated (to activate press Fn & Scr Lk)Icon Color DescriptionOrange DC Power is Plugged InGreen The Computer is OnBlinking Green The Computer is in Sleep ModeOrange The Battery is ChargingGreen The Battery is Fully ChargedBlinking Orange The Battery Has Reached Critically Low Power StatusGreen The (optional) Wireless LAN Module is Powered OnOrange The (optional) Bluetooth Module is Powered OnGreen The (optional) 3.5G Module is Powered On
1 - 8 Hot Key Buttons & KeyboardQuick Start Guide1Hot Key Buttons & KeyboardThese buttons give instant access to the default Inter-net browser and e-mail program, and allow you to tog-gle the Silent Mode on/off with one quick buttonpress.Table 1 - 4 - Hot Key Buttons*When enabled, Silent Mode will reduce fan noiseand save power consumption. Note this may reducecomputer performance.The keyboard has a numerical keypad for easy numer-ic data input, and features Function Keys to allow youto change operational features instantly.Activate the Number Lock feature by pressing theNum Lk key at the top right of the keyboard. You maycheck if Number Lock is enabled or not by looking atthe LED status indicators.Hot Key FunctionActivate the Default E-Mail Browser Activate the Default Internet ProgramToggle *Silent Mode (for power saving)Other KeyboardsIf your keyboard is damaged or you just want to makea change, you can use any standard USB keyboard.The system will detect and enable it automatically.However special functions/AP-Key buttons unique tothe system’s regular keyboard may not work.
Keyboard 1 - 9Quick Start Guide 1KeyboardThe keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you tochange operational features instantly (see Figure 1 - 3). See Table 1 - 5, on page 1 - 10 for full function keycombination details.Figure 1 - 3 - KeyboardFn KeyFunction KeysNumLk & ScrLk KeysNumeric KeypadNumerical Keypad Play/Pause KeyFunction KeysToggle Key3.5G ModulePower NumLk & ScrLk KeysFn KeyOther KeyboardsIf your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The systemwill detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard maynot work.
1 - 10 Function KeysQuick Start Guide1Function KeysThe function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down.Table 1 - 5 - Function KeysFn Key Function Fn Key FunctionFn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display ToggleFn + _ 3.5G Module Power Toggle Fn + F8 Decrease LCD BrightnessFn + F1 TouchPad Toggle Fn + F9 Increase LCD BrightnessFn + F2 Turn LCD Backlight Off(Press a key to or use TouchPad to turn on) Fn + F10 PC Camera Module Power ToggleFn + F3 Mute Toggle Fn + F11 Wireless LAN Module Power ToggleFn + F4 Sleep Toggle Fn + F12 Bluetooth Module Power ToggleFn + F5 Decrease Audio Volume Fn + NumLk Number Lock ToggleFn + F6 Increase Audio Volume Fn + ScrLk Scroll Lock ToggleSpecial CharactersSome software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by usingthe numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.
System Map: Front & Rear Views 1 - 11Quick Start Guide 1System Map: Front & Rear Views Figure 1 - 4Front & Rear Views1. LCD Latches2. LED Power & Communication Indicators3. 7-in-1 Card Reader4. S/PDIF-Out Jack5. Microphone-In Jack6. Headphone-Out Jack7. Battery2541 1637-in-1 Card ReaderThe card reader allows you to use the most popular digital storage card formats:MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter)7
1 - 12 System Map: Left & Right ViewsQuick Start Guide1System Map: Left & Right ViewsFigure 1 - 5Left & Right Views1. DC-In Jack2. RJ-45 LAN Jack3. External Monitor Port4. Vent/Fan Intake/Outlet5. 3 * USB 2.0 Ports6. Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3)7. RJ-11 Phone Jack8. Security Lock Slot1524687355OverheatingTo prevent your computer from overheating make sure nothing blocks the vent(s)/fan in-take(s) while the computer is in use.
System Map: Left & Right Views 1 - 13Quick Start Guide 1Disk Eject WarningDon’t try to eject a CD/DVD while the system is ac-cessing it. This may cause the system to “crash”. Stopthe disk first then eject it, or press the stop buttontwice.CD/DVD Emergency EjectIf you need to manually eject a CD/DVD (e.g. due toan unexpected power interruption) you may push theend of a straightened paper clip into the emergencyeject hole. Do not use a sharpened pencil or any ob-ject that may break and become lodged in the hole.Don’t try to remove a floppy disk/CD/DVD while thesystem is accessing it. This may cause the system to“crash”.Changing DVD Regional CodesGo to the Control Panel and double-click DeviceManager (Hardware and Sound), then click the +next to DVD/CD-ROM drives. Double-click on theDVD-ROM device to bring up the Properties dialogbox, and select the DVD Region (tab) to bring up thecontrol panel to allow you to adjust the regional code(see “DVD Regional Codes” on page 2 - 5).DVD region detection is device dependent, not OS-dependent. You can select your module’s regioncode 5 times. The fifth selection is permanent. Thiscannot be altered even if you change your operatingsystem or you use the module in another computer.
1 - 14 System Map: Bottom ViewQuick Start Guide1System Map: Bottom View Figure 1 - 6Bottom View1. Battery2. Hard Disk Bay Cover (3.5G Module Location)3. RAM & CPU Bay Cover231Battery InformationAlways completely discharge, then fully charge, a new battery before using it. Completelydischarge and charge the battery at least once every 30 days or after about 20 partial dis-charges. See “Battery Information” on page 3 - 10 for full instructions.CPUThe CPU is not a user serviceablepart. Opening this compartment,or accessing the CPU in any way,may violate your warranty.OverheatingTo prevent your computer fromoverheating make sure nothingblocks the Vent/Fan Intake whilethe computer is in use.
Windows Vista Start Menu & Control Panel 1 - 15Quick Start Guide 1Windows Vista Start Menu & Control PanelMost of the control panels, utilities and programs within Windows Vista (and most other Windows versions) areaccessed from the Start menu. When you install programs and utilities they will be installed on your hard diskdrive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menuicon , and then select Properties if you want to customize the appearance of the Start menu.In many instances throughout this manual you will see an instruction to open the Control Panel. The ControlPanel is accessed from the Start menu, and it allows you to configure the settings for most of the key featuresin Windows (e.g. power, video, network, audio etc.). Windows Vista provides basic controls for many of the fea-tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listedin Table 4 - 1, on page 4 - 3. To see all controls it may be necessary to toggle to Classic View on.Figure 1 - 7 - Start Menu & Control PanelClick here to toggle Classic View
1 - 16 Video FeaturesQuick Start Guide1Video FeaturesYou can switch display devices, and configure display options, from the Display Settings control panel (in Per-sonalization) in Windows Vista and/or the SiS VGA Control Center. For further information see “SIS VideoDriver Controls” on page B - 1.To access Windows Vista Display Settings:1. Click Start, and click Control Panel (or point to Settings and click Control Panel).2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click Personalization > Display Settings).3. Move the slider to the preferred setting in Resolution: (Figure 1 - 8 on page 1 - 17).4. Click the arrow, and scroll to the preferred setting In Colors: (Figure 1 - 8 on page 1 - 17).5. Click Advanced Settings (button) (Figure 1 - 8 on page 1 - 17) to bring up the Advanced Settings tabs.To access the SiS VGA Control Center:1. Click Start, and click Control Panel (or point to Settings and click Control Panel).2. Click SiS VGA Control Center (or click Appearance and Personalization > SiS VGA Control Center).3. Click the top menu icons to bring up the appropriate control panel to adjust the settings.4. You can also access SiS VGA Control Center by right-clicking the SIS Tray taskbar icon , and selectingControl Center.1234
Video Features 1 - 17Quick Start Guide 1Figure 1 - 8 - Display Settings & SiS VGA Control Center21344
1 - 18 Power OptionsQuick Start Guide1Power OptionsThe Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 15) allows youto configure power management features for your computer. You can conserve power by means of power plansand configure the options for the power button, sleep button, computer lid (when closed), display and sleepmode from the left menu. Note that the Power saver plan may have an affect on computer performance.Click to select one of the existing plans, or click Create a power plan in the left menu and select the options tocreate a new plan. Click Change Plan Settings and click Change advanced power settings to access further con-figuration options.Pay attention to the instructions on battery care in “Battery Information” on page 3 - 10.Figure 1 - 9 - Power OptionsNote: Sleep is the default power saving state in Windows Vista
Features & ComponentsOverview 2 - 12Chapter 2: Features & ComponentsOverviewRead this chapter to learn more about the following main features and componentsof the computer:•Hard Disk Drive• Optical (CD/DVD) Device• 7-in-1 Card Reader• ExpressCard Slot• TouchPad and Buttons/Mouse• Function/Hot Key Indicators• Audio Features• Adding a Printer
Features & Components2 - 2 Hard Disk Drive2Hard Disk DriveThe hard disk drive is used to store your data in the computer. The hard disk can betaken out to accommodate other 2.5" serial (SATA) hard disk drives (see “Storage”on page C - 2) with a height of 9.5 mm.The hard disk is accessible from the bottom of your computer as seen below. For fur-ther details see “Upgrading the Hard Disk Drive” on page 6 - 4.Power SafetyBefore attempting to ac-cess any of the internalcomponents of yourcomputer please ensurethat the machine is notconnected to the ACpower, and that the ma-chine is turned off. Alsoensure that all peripher-al cables, includingphone lines, are discon-nected from the comput-er.Figure 2 - 1Hard Disk Location
Features & ComponentsOptical (CD/DVD) Device 2 - 32Optical (CD/DVD) DeviceThere is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de-vice will depend on the module you purchased (see “Storage” on page C - 2). Theoptical device is usually labeled “Drive D:” and may be used as a boot device ifproperly set in the BIOS (see “Boot Menu” on page 5 - 12).Loading DiscsTo insert a CD/DVD, press the open button and carefully place a CD/DVD ontothe disc tray with label-side facing up (use just enough force for the disc to click ontothe tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and youare ready to start. The busy indicator will light up while data is being accessed,or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt-ed, insert an object such as a straightened paper clip into the emergency eject hole to open the tray.Sound Volume AdjustmentHow high the sound vol-ume can be set dependson the setting of the vol-ume control within Win-dows. Click the Volumeicon on the taskbar tocheck the setting (see“Audio Features” onpage 2 - 10). Figure 2 - 2Optical Device123123
Features & Components2 - 4 Optical (CD/DVD) Device2Handling CDs or DVDsProper handling of your CDs/DVDs will prevent them from being damaged. Pleasefollow the advice below to make sure that the data stored on your CDs/DVDs can beaccessed.Note the following:• Hold the CD or DVD by the edges; do not touch the surface of the disc.• Use a clean, soft, dry cloth to remove dust or fingerprints.• Do not write on the surface with a pen.• Do not attach paper or other materials to the surface of the disc.• Do not store or place the CD or DVD in high-temperature areas.• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.• Do not bend the CD or DVD.• Do not drop or subject the CD or DVD to shock.CD Emergency EjectIf you need to manuallyeject a CD (e.g. due toan unexpected powerinterruption) you maypush the end of astraightened paper clipinto the emergency ejecthole. However pleasedo NOT use a sharp-ened pencil or similarobject that may breakand become lodged inthe hole.Disk Eject WarningDon’t try to remove aCD/DVD while the sys-tem is accessing it. Thismay cause the systemto “crash”.
Features & ComponentsOptical (CD/DVD) Device 2 - 52DVD Regional CodesTo change the DVD regional codes see “Changing DVD Regional Codes” onpage 1 - 13..DVD Regional CodingRegion Geographical Location1 USA, Canada2Western Europe, Japan, South Africa, Middle East & Egypt3South-East Asia, Taiwan, South Korea, The Philippines, Indonesia, Hong Kong4South & Central America, Mexico, Australia, New Zealand5N Korea, Russia, Eastern Europe, India & Most of Africa6ChinaTable 2 - 1DVD Regional Coding Figure 2 - 3DVD Regions
Features & Components2 - 6 7-in-1 Card Reader27-in-1 Card ReaderThe card reader allows you to use some of the latest digital storage cards. Push thecard into the slot and it will appear as a removable device, and can be accessed inthe same way as your hard disk (s). Make sure you install the Card Reader driver(see “CardReader” on page 4 - 6).*Note: The PC adapters are usually supplied with these cards.Card Reader CoverMake sure you keep therubber cover provided inthe card reader whennot in use. This will helpprevent foreign objectsand/or dust getting in tothe card reader. Figure 2 - 4Right View1. Card Reader• MMC (MultiMedia Card)• SD (Secure Digital)• MS (Memory Stick)• MS Pro (Memory Stick Pro)• MS Duo (requires PC adapter*)• Mini SD (requires PC adapter*)• RS MMC (requires PC adapter*)1
Features & ComponentsExpressCard Slot 2 - 72ExpressCard SlotThe computer is equipped with an ExpressCard/34/54 slot that reads Express Card/34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PCCards). Make sure you install the Card Reader driver (see “CardReader” on page 4- 6).ExpressCard/54 is used for applications which require a larger interface slot, e.g.CompactFlash card reader. The number denotes the card width; 54mm for the Ex-press Card/54 and 34mm for the ExpressCard/34.Inserting and Removing ExpressCards• Align the ExpressCard with the slot and push it in until it locks into place (as pictured in the generic figure below).• To remove an ExpressCard, simply press the card to eject it.ExpressCard Slot CoverMake sure you keep therubber cover provided inthe ExpressCard slotwhen not in use. Thiswill help prevent foreignobjects and/or dust get-ting in to the Express-Card Slot. Figure 2 - 5Left View1. Express Card Slot Figure 2 - 6Inserting & Removing Express Cards1
Features & Components2 - 8 TouchPad and Buttons/Mouse2TouchPad and Buttons/MouseThe TouchPad is an alternative to the mouse; however, you can also add a mouse toyour computer through one of the USB ports. The TouchPad buttons function inmuch the same way as a two-button mouse. Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) youcan configure the functions by double-clicking the TouchPad driver icon on thetaskbar. You may then configure the TouchPad tapping, buttons, scrolling, pointermotion and sensitivity options to your preferences. You will find further informationat www.synaptics.com.Mouse DriverIf you are using an ex-ternal mouse your op-erating system may beable to auto-configureyour mouse during itsinstallation or only en-able its basic functions.Be sure to check thedevice’s user docu-mentation for details. Figure 2 - 7Mouse Properties
Features & ComponentsFunction/Hot Key Indicators 2 - 92Function/Hot Key IndicatorsThe function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fnkey is held down. In addition to the basic function key combinations; visual indica-tors (see the table below) are available when the hot key utility is installed (see “HotKey” on page 4 - 6). After installing the driver an icon will appear in the taskbar.*When enabled, Silent Mode will reduce fan noise and save power consumption.Note this may reduce computer performance.Fn Keys Function Fn Keys FunctionFn + F1 TouchPad Toggle Fn + F10PC Camera Power ToggleFn + F3 Mute Toggle Fn + F11WLAN Module Power ToggleFn +F5/F6Volume Decrease/IncreaseFn + F12Bluetooth Module Power ToggleFn +F8/F9Brightness Decrease/Increase*Silent Mode ToggleTable 2 - 2Function/Hot Key Combo Indicators
Features & Components2 - 10 Audio Features2Audio FeaturesYou can configure the audio options on your computer from the Sound controlpanel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/control panel (right-click the taskbar icon to bring up an audio menu). The volumemay also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume AdjustmentThe sound volume levelis set using the volumecontrol within Windows(and the volume func-tion keys on the comput-er). Click the volumeicon in the taskbar tocheck the setting. Figure 2 - 8Realtek Audio ManagerRight-click the icon to access the menu above.
Features & ComponentsAdding a Printer 2 - 112Adding a PrinterThe most commonly used peripheral is a printer. The following conventions willhelp you to add a printer; however it is always best to refer to the printer manual forspecific instructions and configuration options.USB PrinterMost current printers have a USB interface connection. You may use any one of theports to connect the printer.Install Instructions:1. Set up the printer according to its instructions (unpacking, paper tray, toner/ink car-tridge etc.).2. Turn ON the computer.3. Turn ON the printer.4. Connect the printer’s USB cable to one of the USB ports on the computer.5. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.Parallel PrinterThis is still a very common type of printer. The install instructions are in the sidebar,however you will need to purchase a parallel to USB converter.Parallel PrinterAfter setting up the print-er attach the parallel ca-ble to the printer.Connect the printer’sparallel cable to the Par-allel to USB converter,and then plug the con-verter into the USB port.Turn ON the printer,then turn ON the com-puter.Windows will identify theprinter and either loadone of its own drivers orask you to supply one.Follow the on-screen in-structions.
Power ManagementOverview 3 - 13Chapter 3: Power ManagementOverviewTo conserve power, especially when using the battery, your computer power man-agement conserves power by controlling individual components of the computer(the monitor and hard disk drive) or the whole system. This chapter covers:• The Power Sources• Turning on the Computer• Power Plans• Power-Saving States• Configuring the Power Buttons• Battery InformationThe computer uses enhanced power saving techniques to give the operating system(OS) direct control over the power and thermal states of devices and processors. Forexample, this enables the OS to set devices into low-power states based on user set-tings and information from applications.OS NotePower managementfunctions will vary slight-ly depending on youroperating system. Formore information it isbest to refer to the user’smanual of your operat-ing system. (Note: All pictures usedon the following pagesare from the WindowsVista OS.)
Power Management3 - 2 The Power Sources3The Power SourcesThe computer can be powered by either an AC/DC adapter or a battery pack.AC/DC AdapterUse only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components.1. Attach the AC/DC adapter to the DC-in jack on the left of the computer.2. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter.3. Raise the lid/LCD to a comfortable viewing angle.4. Press the power button to turn “On”.BatteryThe battery allows you to use your computer while you are on the road or when anelectrical outlet is unavailable. Battery life varies depending on the applications andthe configuration you're using. To increase battery life, let the battery dischargecompletely before recharging (see “How do I completely discharge the battery?”on page 3 - 14).We recommend that you do not remove the battery. For more information on the bat-tery, please refer to “Battery Information” on page 3 - 10.
Power ManagementTurning on the Computer 3 - 33Turning on the ComputerNow you are ready to begin using your computer. To turn it on simply press the pow-er button on the front panel.When the computer is on, you can use the power button as a Sleep/Hibernate hot-key button when it is pressed for less than 4 seconds (pressing and holding the powerbutton for longer than this will force the computer to shut down). Use Power Op-tions (Hardware and Sound menu) control panel in Windows Vista to configurethis feature.Shut DownNote that you should al-ways shut your comput-er down by choosing theShut Down commandfrom the Lock ButtonMenu in Windows Vis-ta. This will help preventhard disk or systemproblems.Forced OffIf the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the pow-er button for 4 seconds, or longer, to force the system to turn itself off.Power Button SleepSleep is the default power mode when the power button is pressed for less than 4 seconds.You may configure the options for the power button from the Power Options (Hardwareand Sound menu) control panel in Windows Vista (see your OS’s documentation, or“Configuring the Power Buttons” on page 3 - 8 for details).
Power Management3 - 4 Power Plans3Power PlansThe computer can be configured to conserve power by means of power plans. Youcan use (or modify) an existing power plan, or create a new one.The settings may be adjusted to set the display to turn off after a specified time, andto send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to ac-cess further configuration options in Advanced Settings.Resuming OperationSee Table 3 - 1, onpage 3 - 9 for informa-tion on how to resumefrom a power-savingstate.PasswordIt is recommended thatyou enable a passwordon system resume in or-der to protect your data.Figure 3 - 1Power Plan Advanced Settings
Power ManagementPower Plans3-53Each Windows power plan will also adjust the processor performance of your ma-chine in order to save power. This is worth bearing in mind if you are experiencingany reduced performance (especially under DC/battery power).Choose High performance for maximum performance when the computer is pow-ered from an AC power source. Choose the Power saver (bear in mind that thisscheme may slow down the overall performance of the computer in order to savepower) for maximum power saving when the computer is battery (DC power) pow-ered.Figure 3 - 2Power Plans
Power Management3 - 6 Power-Saving States3Power-Saving StatesYou can use power-saving states to stop the computer’s operation and restart whereyou left off. Sleep is the default power-saving state in Windows Vista.Earlier versions of Windows used Stand By and Hibernate as system power-savingstates. Windows Vista combines the features of Stand By and Hibernate into the de-fault Sleep power-saving state.SleepIn Sleep all of your work, settings and preferences are saved to memory before thesystem sleeps. When you are not using your computer for a certain length of time,which you specify in the operating system, it will enter Sleep to save power. The PC wakes from Sleep within seconds and will return you to where you last leftoff (what was on your desktop) without reopening the application(s) and file(s) youlast used.If your mobile PC in Sleep is running on battery power the system will use only aminimum amount of power. After an extended period the system will save all theinformation to the hard disk and shut the computer down before the battery becomesdepleted.Power ButtonThe Power Button in the Start Menu (inClassic View use theShut Down button )can be used to send thecomputer into a power-saving state.Sleep Mode & Mobile PC BatteryA mobile PC in Sleepuses very little batterypower. After an extended peri-od of time the computerwill save any open docu-ments and applicationsto hard disk.
Power ManagementPower-Saving States 3 - 73HibernateHibernate uses the least amount of power of all the power-saving states and savesall of your information on a part of the hard disk before it turns the system off. If apower failure occurs the system can restore your work from the hard disk; if a powerfailure occurs when work is saved only to memory, then the work will be lost. Hi-bernate will also return you to where you last left off within seconds. You shouldput your mobile PC into Hibernate if you will not use the computer for a period oftime, and will not have the chance to charge the battery.Shut DownYou should shut down the computer if you plan to install new hardware (don’t for-get to remove the battery and follow all the safety instructions in Chapter 6), planto be away from the computer for several days, or you do not need it to wake up andrun a scheduled task. Returning to full operation from shut down takes longer thanfrom Sleep or Hibernate.Silent ModeYou can use SilentMode to reduce powerconsumption and fannoise.Use the Silent Modehot key to toggle thismode on/off. On screen visual indica-tors and the LED indica-tor will display theSilent Mode status (seeTable 2 - 2, on page 2 -9, and Table 1 - 3, onpage 1 - 7).Note Silent Mode mayreduce computer perfor-mance.Figure 3 - 3Lock Button menu
Power Management3 - 8 Configuring the Power Buttons3Configuring the Power ButtonsThe power/sleep button (Fn + F4 key combo) and closed lid may be set to send thecomputer in to a power-saving state.Password ProtectionIt is recommended thatyou enable a passwordon wake up in order toprotect your data.However you can dis-able this setting from thePower Options menuby clicking Require apassword on wakeupin the left menu, and se-lecting the options (clickChange settings thatare currently unavail-able).Figure 3 - 4Power Options Define Power Buttons
Power ManagementConfiguring the Power Buttons 3 - 93Resuming OperationYou can resume operation from power-saving states by pressing the power button,or in some cases pressing the sleep button (Fn + F4 key combo).Power Status Icon Color To ResumePower Off Off Press the Power ButtonSleep Blinking Green Press the Power ButtonPress the Sleep Button (Fn + F4 Key Combo)Hibernate Off (battery) Press the Power ButtonOrange (AC/DC adapter)Display Turned Off Green Press a Key or Move the Mouse/TouchpadClosing the LidIf you have chosen tosend the computer toSleep when the lid isclosed, raising the lidwill wake the system up.Table 3 - 1Resuming OperationPower ButtonWhen the computer is on, you can use the power button as a Sleep/Hibernate/Shut Downhot key button when it is pressed for less than 4 seconds (pressing and holding the powerbutton for longer than this will force the computer to shut down).
Power Management3 - 10 Battery Information3Battery InformationPlease follow these simple guidelines to get the best use out of your battery.Battery PowerYour computer’s battery power is dependent upon many factors, including the pro-grams you are running, and peripheral devices attached. You can set actions to betaken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels frompower plan Advanced Settings (see Figure 3 - 1 on page 3 - 4).Click the battery icon in the taskbar to see the current battery level and chargestatus.Low Battery WarningWhen the battery is criti-cally low, immediatelyconnect the AC/DCadapter to the computeror save your work, oth-erwise, the unsaveddata will be lost whenthe power is depleted.Figure 3 - 5Battery Icon (Taskbar) & Battery Advanced Settings
Power ManagementBattery Information 3 - 113Conserving Battery Power•Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance.• Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.• Reduce the amount of time before the display is turned off.• Close wireless, Bluetooth, modem or communication applications when they are not being used.• Disconnect/remove any unnecessary external devices e.g. USB devices, ExpressCards etc.Windows Mobility CenterThe Windows MobilityCenter control panel pro-vides an easy point of ac-cess for information onbattery status, power plansused and wireless devicestatus etc.Figure 3 - 6Windows Mobility Center
Power Management3 - 12 Battery Information3Battery LifeBattery life may be shortened through improper maintenance. To optimize the lifeand improve its performance, fully discharge and recharge the battery at leastonce every 30 days.We recommend that you do not remove the battery yourself. If you do need to re-move the battery for any reason see “Removing the Battery” on page 6 - 3.New BatteryAlways completely discharge, then fully charge, a new battery (see “Battery FAQ”on page 3 - 14 for instructions on how to do this).Recharging the Battery with the AC/DC AdapterThe battery pack automatically recharges when the AC/DC adapter is attached andplugged into an electrical outlet. If the computer is powered on, and in use, it willtake several hours to fully recharge the battery. When the computer is turned off butplugged into an electrical outlet, battery charge time is less. (Refer to “- LED StatusIndicators” on page 1 - 7 for information on the battery charge status, and to “Bat-tery Information” on page 3 - 10 for more information on how to maintain andproperly recharge the battery pack.)
Power ManagementBattery Information 3 - 133Proper handling of the Battery Pack• DO NOT disassemble the battery pack under any circumstances• DO NOT expose the battery to fire or high temperatures, it may explode• DO NOT connect the metal terminals (+, -) to each otherCautionDanger of explosion ifbattery is incorrectly re-placed.Replace only with thesame or equivalent typerecommended by themanufacturer. Discardused battery accordingto the manufacturer’s in-structions.Damaged Battery WarningShould you notice any physical defects (e.g. the battery is bent out of shape after beingdropped), or any unusual smells emanating from the notebook battery, shut your computerdown immediately and contact your service center. If the battery has been dropped we donot recommend using it any further, as even if the computer continues to work with a dam-aged battery in place, it may cause circuit damage, which may possibly result in fire. It isrecommended that you replace your computer battery every two years.
Power Management3 - 14 Battery Information3Battery FAQHow do I completely discharge the battery?Use the computer with battery power until it shuts down due to a low battery. Don’tturn off the computer even if a message indicates the battery is critically low, just letthe computer use up all of the battery power and shut down on its own.1. Save and close all files and applications.2. Create a power plan for discharging the battery and set all the options to Never.3. Click Change plan settings (after saving it) and click Change advanced power settings.Figure 3 - 7Power Plan Create
Power ManagementBattery Information 3 - 1534. Scroll down to Battery and click + to expand the battery options.5. Choose the options below (click Yes if a warning appears):• Low battery levels = 0%• Critical battery Levels = 0%• Low battery action = Do Nothing• Critical battery action (On battery) = Shut Down• Critical battery action (Plugged in) = Do NothingFigure 3 - 8Power Options Advanced Settings - Battery
Power Management3 - 16 Battery Information3How do I fully charge the battery?When charging the battery, don’t stop until the LED charging indicator light changesfrom orange to green.How do I maintain the battery?Completely discharge and charge the battery at least once every 30 days or afterabout 20 partial discharges.
Drivers & UtilitiesWhat to Install 4 - 14Chapter 4: Drivers & UtilitiesThis chapter deals with installing the drivers and utili-ties essential to the operation or improvement of someof the computer’s subsystems. The system takes ad-vantage of some newer hardware components forwhich the latest versions of most available operatingsystems haven’t built in drivers and utilities. Thus,some of the system components won’t be auto-config-ured with an appropriate driver or utility during oper-ating system installation. Instead, you need tomanually install some system-required drivers andutilities. What to InstallThe Device Drivers & Utilities + User’s Manual CD-ROM contains the drivers and utilities necessary forthe proper operation of the computer. Table 4 - 1, on page 4 - 3 lists what you need to installand it is very important that the drivers are in-stalled in the order indicated (see “Driver Installa-tion” on page D - 25 for Windows XP information).Module Driver InstallationThe procedures for installing drivers for the PC Cam-era, Wireless LAN, Bluetooth, 3G and Fingerprintmodules are provided in “Modules & Options” onpage 7 - 1.
Drivers & Utilities4 - 2 Driver Installation4Driver InstallationInsert the Device Drivers & Utilities + User’s ManualCD-ROM and click Install Drivers (button).If you wish to install the drivers manually see overleaffor the driver path information.Figure 4 - 1 - Drivers Installer Screen 11. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.2. Click to select the driver you wish to install, after installing each driver it will become grayed out (if you need to reinstall any driver, click the Unlock button).3. Follow the instructions for each individual driver installation procedure as listed on the following pages. Figure 4 - 2 - Drivers Installer Screen 2
Drivers & UtilitiesDriver Installation 4 - 34Manual Driver InstallationIf you wish to install the drivers manually, click the Exit button to quit the Drivers Installer application, andthen browse to the executable file in the location listed in the table below and follow the installation procedurefor each driver. Note that X is the drive letter assigned to the CD/DVD-ROM drive.Table 4 - 1 - Driver Installation and LocationDriver Page Driver LocationVideo Page 4 - 5 Vista 32bit: X:\Drivers\01VGA\setup.exeAudio Page 4 - 5 Vista 32bit: X:\Drivers\02Audio\Setup.exeModem Page 4 - 5 Vista 32bit: X:\Drivers\03Modem\ssetup.exeLAN Page 4 - 5 Vista 32bit: X:\Drivers\04Lan\setup.exeTouchPad Page 4 - 6 Vista 32bit: X:\Drivers\05Touchpad\setup.exeCardReader Page 4 - 6 Vista 32bit: X:\Drivers\06Reader\Setup.exeHot Key Page 4 - 6 Vista 32bit: X:\Drivers\07Hotkey\Setup.exePC Camera Module Page 7 - 3 Vista 32bit: X:\Others\02Camera\32bit\setup.exe (for 300K or 1.3M pixel Camera)Vista 32bit: X:\Others\02Camera\D-max2.0M\Setup.exe (for 2.0M pixel Camera)Wireless LAN Module Page 7 - 11 Vista 32bit: X:\Others\01RTL8187\setup.exeBluetooth Module Page 7 - 16 Vista 32bit: X:\Others\03Bluetooth\setup.exe3.5G Module Page 7 - 23 Vista 32bit: X:\Others\04_3G\3G.msiFingerprint Reader Module Page 7 - 28 Vista 32bit: X:\Others\05Fingerprint\Application\x86\autorun.exe
Drivers & Utilities4 - 4 Driver Installation4Updating/Reinstalling Individual DriversIf you wish to update/reinstall individual drivers itmay be necessary to uninstall the original driver.To dothis go to the Control Panel in the Windows OS anddouble-click the Programs and Features icon (Pro-grams > Uninstall a program). Click to select thedriver (if it is not listed see below) and click Uninstall,and then follow the on screen prompts (it may be nec-essary to restart the computer). Reinstall the driver asoutlined in this chapter.If the driver is not listed in the Programs and Fea-tures menu:1. Click Start, and click Control Panel (or point to Settings and click Control Panel).2. Double-click Device Manager (Hardware and Sound > Device Manager).3. Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).4. Click Driver (tab) and click the Update Driver or Uninstall button and follow the on screen prompts.User Account Control (Win Vista)If a User Account Control prompt appears as part ofthe driver installation procedure, click Continue orAllow, and follow the installation procedure as direct-ed.Windows Security MessageIf you receive a Windows security message as part ofthe driver installation process. Just click “Install thisdriver software anyway” or Install to continue the in-stallation procedure.You will receive this message in cases where the driv-er has been released after the version of Windows youare currently using. All the drivers provided will havealready received certification for Windows.New Hardware FoundIf you see the message “New Hardware Found”(Found New Hardware Wizard) during the installa-tion procedure (other than when outlined in thedriver install procedure), click Cancel to close thewindow, and follow the installation procedure.
Drivers & UtilitiesDriver Installation 4 - 54Driver Installation ProcedureVideo1. Click 1.Install VGA Driver > Yes.2. Click Yes (click Yes if you want to view the ReadMe file).3. Click Yes to restart the computer.Audio1. Click 2.Install Audio Driver > Yes. 2. Click Next.3. Click Finish to restart the computer.Modem1. Click 3.Install Modem Driver > Yes.2. Click OK.3. The modem is ready for dial-up configuration.LAN1. Click 4.Install LAN Driver > Yes.2. Click Next.3. Click Finish > Finish to restart the computer.4. The network settings can mow be configured.Modem Country SelectionGo to the Phone and Modem Options control panel(Hardware and Sound) and make sure the modemcountry selection is appropriate for you.
Drivers & Utilities4 - 6 Driver Installation4TouchPad1. Click 5.Install Touchpad Driver > Yes.2. Click Next.3. Click Finish > Restart Now to restart the com-puter.4. You may then configure your TouchPad as out-lined in “TouchPad and Buttons/Mouse” on page 2 - 8.CardReader1. Click 6.Install Cardreader Driver > Yes.2. Click Next > Next.3. Click Finish to restart the computer.Hot Key1. Click 7.Install HOTKEY Driver > Yes. 2. Click Next > Install.3. Click Finish > Finish to restart the computer.PC Camera ModuleSee the introduction in “PC Camera Module” onpage 7 - 2, and check the installation procedure.Wireless LAN ModuleSee the introduction in “802.11 b/g USB WLAN Mod-ule” on page 7 - 11, and check the installation proce-dure.Bluetooth ModuleSee the introduction in “Bluetooth Module” onpage 7 - 16, and check the installation procedure.3.5G ModuleSee the introduction in “3.5G Module” on page 7 - 20,and check the installation procedure.Fingerprint Reader ModuleSee the introduction in “Fingerprint Reader Module”on page 7 - 28, and check the installation procedure.
BIOS UtilitiesOverview 5 - 15Chapter 5: BIOS UtilitiesOverviewThis chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test)Configuration: The Setup utility If your computer has never been set up, or you are making important changes to thesystem (e.g. hard disk setup), then you should review this chapter first and note theoriginal settings found in Setup. Even if you are a beginner, keep a record of the set-tings you find and any changes you make. This information could be useful if yoursystem ever needs servicing.There is one general rule: Don’t make any changes unless you are sure of what youare doing. Many of the settings are required by the system, and changing them couldcause it to become unstable or worse. If you have any doubts, consult your servicerepresentative.BIOS Settings WarningIncorrect settings cancause your system tomalfunction. To correctmistakes, return to Set-up and restore the Set-up Defaults with <F9>.
BIOS Utilities5 - 2 The Power-On Self Test (POST)5The Power-On Self Test (POST)Each time you turn on the computer, the system takes a few seconds to conduct aPOST, including a quick test of the on-board RAM (memory).As the POST proceeds, the computer will tell you if there is anything wrong. If thereis a problem that prevents the system from booting, it will display a system summaryand prompt you to run Setup. If there are no problems, the Setup prompt will disappear and the system will loadthe operating system. Once that starts, you can’t get into Setup without rebooting.POST Screen1.BIOS information2.CPU type 3.Memory status4.Enter Setup promptappears only duringPOSTNote: The POST screenas pictured right is forguideline purposes only.The POST screen onyour computer may ap-pear slightly different. Ifyou disable the Boot-time Diagnostic Screen,the POST screen will notappear.Figure 5 - 1POST ScreenPhoenix TrustedCore(tm) NBCopyright 1985-2006 Phoenix Technologies Ltd.All Rights ReservedBios Revision: ********KBC/EC Firmware Revision: ********CPU=1Processors Detected, Cores per Processor = 2Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz323M System RAM Passed2048 KB L2 CacheSystem BIOS shadowedATAPI CD-ROM: Optiarc DVD RW AD-7530AMouse intializedPress <F2> to enter SETUP1234
BIOS UtilitiesThe Power-On Self Test (POST) 5 - 35Failing the POSTErrors can be detected during the POST. There are two categories, “fatal” and “non-fatal”.Fatal ErrorsThese stop the boot process and usually indicate there is something seriously wrongwith your system. Take the computer to your service representative or authorizedservice center as soon as possible.Non-Fatal ErrorsThis kind of error still allows you to boot. You will get a message identifying theproblem (make a note of this message!) followed by the prompt:• Press <F1> to resume• <F2> to enter Setup Press F1 to see if the boot process can continue. It may work, without the correctconfiguration. Press F2 to run the Setup program and try to correct the problem. If you still get anerror message after you change the setting, or if the “cure” seems even worse, callfor help.
BIOS Utilities5 - 4 The Setup Program5The Setup ProgramThe Phoenix Setup program tells the system how to configure itself and manage ba-sic features and subsystems (e.g. port configuration).Entering SetupTo enter Setup, turn on the computer and press F2 during the POST. The prompt(Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few secondsafter you turn on the system. If you get a “Keyboard Error”, (usually because youpressed F2 too quickly) just press F2 again.If the computer is already on, reboot using the Ctrl + Alt + Delete combination andthen hold down F2 when prompted. The Setup main menu will appear.
BIOS UtilitiesThe Setup Program 5 - 55Setup ScreensThe following pages contain additional advice on portions of the Setup.Along the top of the screen is a menu bar with menu headings. When you select aheading, a new screen appears. Scroll through the features listed on each screen tomake changes to Setup.Instructions on how to navigate each screen are in the box along the bottom of thescreen. If these tools are confusing, press F1 to call up a General Help screen, andthen use the arrow keys to scroll up or down the page.The Item Specific Help on the right side of each screen explains the highlighteditem and has useful messages about its options.If you see an arrow next to an item, press Enter to go to a sub-menu on that sub-ject. The sub-menu screen that appears has a similar layout, but the Enter key mayexecute a command.Setup MenusThe Setup menusshown in this section arefor reference only. Yourcomputer’s menus willindicate the configura-tion appropriate for yourmodel and options.
BIOS Utilities5-6Main Menu5Main MenuSystem Time & Date (Main Menu)The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If youcan change the date and time settings in your operating system, you will also changethese settings. Some applications may also alter data files to reflect these changes.Figure 5 - 2Main Menu Main Advanced Security Boot ExitF1 Help  Select Item -/+ Change Values F9 Setup DefaultsEsc Exit  Select Menu Enter Select Sub-Menu F10 Save and ExitItem Specific Help<Tab>, <Shift Tab>, or<Enter> selects field.MainSystem Time: [22:12:05]System Date: [04/23/2007] IDE Channel 0 Master [Optiarc DVD RW AD-7530A-(] SATA Port 1 [FUJITSU MHV2100BH PL-(S1)]System Memory 633 KBExtended Memory 390144 KBPhoenixBIOS Setup Utility
BIOS UtilitiesMain Menu 5 - 75IDE Channel 0 Master (Main Menu)Pressing Enter opens the sub-menu to show the configuration of an optical Deviceon the computer’s IDE Channel 0. Use the Auto (Type:) setting to have the itemsconfigured automatically for you.SATA Port 1 (Main Menu)Pressing Enter opens the sub-menu to show the configuration of a HDD on the com-puter’s SATA port. Use the Auto (Type:) setting to have the items configured auto-matically for you.System/Extended Memory: (Main Menu)This item contains information on the system memory, and is not user configurable.The system will auto detect the amount of memory installed.
BIOS Utilities5 - 8 Advanced Menu5Advanced MenuInstalled O/S: (Advanced Menu)This setting tells the computer what kind of operating system you’re using. Figure 5 - 3Advanced MenuPhoenixBIOS Setup UtilityMain Advanced Security Boot ExitF1 Help  Select Item -/+ Change Values F9 Setup DefaultsEsc Exit  Select Menu Enter Select Sub-Menu F10 Save and ExitItem Specific HelpSelect the operatingsystem installedon your system whichyou will use mostcommonly.Note: An incorrectsetting can causesome operatingsystems to displayunexpected behavior.AdvancedInstalled O/S: [WinXP/Vista]IDE PATA+SATA ID Control [5513+1183]Boot-time Diagnostic Screen: [Enabled]
BIOS UtilitiesAdvanced Menu 5 - 95IDE PATA+SATA ID Control (Advanced Menu)You can configure IDE PATA +SATA device ID control from this menu, if youhave specific requirements to do so.Boot-time Diagnostic Screen: (Advanced Menu)Use this menu item to enable/disable the Boot-time Diagnostic Screen. Enable thisitem to display the POST screen as illustrated in “POST Screen” on page 5 - 2.
BIOS Utilities5 - 10 Security Menu5Security MenuSet Supervisor Password (Security Menu)You can set a password for access to the PhoenixBIOS Setup Utility. This will notaffect access to the computer OS (only the PhoenixBIOS Setup Utility).Security MenuThe changes youmake here affect theaccess to the Setuputility itself, and alsoaccess to your ma-chine as it boots up af-ter you turn it on.These settings do notaffect your machine ornetwork passwordswhich will be set inyour software OS.Figure 5 - 4Security MenuMain Advanced SSeeccuurriittyyBoot ExitF1 Help  Select Item -/+ Change Values F9 Setup DefaultsEsc Exit  Select Menu Enter Select Sub-Menu F10 Save and ExitItem Specific HelpSupervisor Passwordcontrols access to thesetup utility.SecuritySupervisor Password Is: ClearSet Supervisor Password [Enter]Password on boot: [Disabled]Fixed disk boot sector: [Normal]PhoenixBIOS Setup Utility
BIOS UtilitiesSecurity Menu 5 - 115Password on boot: (Security Menu)Specify whether or not a password should be entered to boot the computer (you mayonly set a password on boot if a supervisor password is enabled). If “Enabled”is selected, only users who enter a correct password can boot the system (see thewarning in the sidebar). The default setting is “Disabled”. Note: To clear existing passwords press Enter and type the existing password, thenpress Enter for the new password (without typing any password entry) and Enteragain to confirm the password clearance.Fixed disk boot sector: (Security Menu)If you choose “Write-Protect” this will protect against viruses being written to thehard disk boot sector (this is not a substitute for installing an anti-virus program - see“Viruses” on page 8 - 4).Password WarningIf you set a boot pass-word (Password on bootis “Enabled“), NEVERforget your password. The consequences ofthis could be serious. Ifyou cannot rememberyour boot password youmust contact your ven-dor and you may lose allof the information onyour hard disk.
BIOS Utilities5 - 12 Boot Menu5Boot MenuWhen you turn the computer on it will look for an operating system (e.g. WindowsVista) from the devices listed in this menu, and in this priority order. If it cannotfind the operating system on that device, it will try to load it from the next device inthe order specified in the Boot priority order. Item specific help on the right isavailable to help you move devices up and down the order.Figure 5 - 5Boot MenuPhoenixBIOS Setup UtilityF1 Help  Select Item -/+ Change Values F9 Setup DefaultsEsc Exit  Select Menu Enter Select Sub-Menu F10 Save and ExitItem Specific HelpKeys used to view orconfigure devices:Up and Down arrowsselect a device.<+> and <-> movesthe device up or down.<x> exclude or includethe device to boot.<Shift +1> enables ordisables a device.<1 - 4> Loads defaultboot sequence.Boot priority order:1: USB KEY:2: USB FDC:3: USB HDD:4: USB CD: Optiarc DVD RW AD-7530A-(P5: IDE 4: FUJITSU MHV2100BH PL-(S1)6: IDE 5:7: PCI BEV: SiS191 UNDI, PXE-2.18:Excluded from boot order:: USB CDROM:: USB ZIP: USB LS120Main Advanced Security Boot Exit
BIOS UtilitiesExit Menu 5 - 135Exit MenuChoosing to Discard Changes, or Exit Discarding Changes, will wipe out anychanges you have made to the Setup. You can also choose to restore the original Set-up defaults that will return the Setup to its original state, and erase any previouschanges you have made in a previous session.Figure 5 - 6Exit MenuPhoenixBIOS Setup UtilityF1 Help  Select Item -/+ Change Values F9 Setup DefaultsEsc Exit  Select Menu Enter Execute Command F10 Save and ExitItem Specific HelpExit System Setup andsave your changes toCMOS.Exit Saving ChangesExit Discarding ChangesLoad Setup DefaultsDiscard ChangesSave ChangesMain Advanced Security Boot Exit
Upgrading The ComputerOverview 6 - 16Chapter 6: Upgrading The ComputerOverviewThis chapter contains information on upgrading the computer. Follow the steps out-lined to make the desired upgrades. If you have any trouble or problems you can con-tact your service representative for further help. Before you begin you will need:• A small crosshead or Phillips screwdriver• A small regular slotted (flathead) screwdriver• An antistatic wrist strapBefore working with the internal components you will need to wear an antistaticwrist strap to ground yourself because static electricity may damage the compo-nents.The chapter includes:• Removing the Battery• Upgrading the Hard Disk Drive• Upgrading the Optical (CD/DVD) Device• Upgrading the System Memory (RAM)Please make sure that you review each procedure before you perform it.Warranty WarningPlease check with yourservice representativebefore undertaking anyupgrade procedures tofind out if this will VOIDyour warranty.
Upgrading The Computer6 - 2 Overview6When Not to UpgradeThese procedures involve opening the system’s case, adding and sometimes replac-ing parts.You should not perform any of these upgrades if:• Your system is still under warranty or a service contract• You don’t have all the necessary equipment • You’re not in the correct environment• You doubt your abilitiesUnder any of these conditions, contact your service representative to purchase or re-place the component(s).Power Safety WarningBefore you undertakeany upgrade proce-dures, make sure thatyou have turned off thepower, and disconnect-ed all peripherals andcables (including tele-phone lines). It is advis-able to also remove yourbattery in order to pre-vent accidentally turningthe machine on. Removal WarningWhen removing any cover(s) and screw(s) for the purposes of device upgrade, rememberto replace the cover(s) and screw(s) before turning the computer on.
Upgrading The ComputerRemoving the Battery 6 - 36Removing the BatteryIf you are confident in undertaking upgrade procedures yourself, for safety reasonsit is best to remove the battery.1. Turn the computer off, and turn it over.2. Slide the latch in the direction of the arrow.3. Slide the latch in the direction of the arrow, and hold it in place.4. Slide the battery out in the direction of the arrow .Warranty WarningPlease check with yourservice representativebefore undertaking anyupgrade procedures tofind out if this will VOIDyour warranty.Figure 6 - 1Battery Removal123231
Upgrading The Computer6 - 4 Upgrading the Hard Disk Drive6Upgrading the Hard Disk DriveThe hard disk drive can be taken out to accommodate other 2.5" serial (SATA) harddisk drives with a height of 9.5mm (h) (see “Storage” on page C - 2). Follow youroperating system’s installation instructions, and install all necessary drivers and util-ities (see “Driver Installation” on page 4 - 2), when setting up a new hard disk.1. Turn off the computer, and turn it over and remove the battery.2. Locate the hard disk bay cover and remove screws & .3. Remove the hard disk bay cover .4. Grip the tab and slide the hard disk in the direction of arrow .HDD System WarningNew HDD’s are blank. Be-fore you begin make sure:You have backed up anydata you want to keep fromyour old HDD.You have all the CD-ROMsand FDDs required to in-stall your operating systemand programs.If you have access to the in-ternet, download the latestapplication and hardwaredriver updates for the oper-ating system you plan to in-stall. Copy these to aremovable medium.Figure 6 - 2Hard Disk Bay & Screws12343214
Upgrading The ComputerUpgrading the Hard Disk Drive 6 - 565. Lift the hard disk up in the direction of arrow .6. Remove the screws & and cover .7. Reverse the process to install a new hard disk drive.Figure 6 - 3HDD & Cover Removal56 7 85768
Upgrading The Computer6 - 6 Upgrading the Optical (CD/DVD) Device6Upgrading the Optical (CD/DVD) Device1. Turn off the computer, and turn it over and remove the battery.2. Locate the RAM & CPU bay cover and remove screws - .3. Remove the screw at point , and use a screwdriver to carefully push out the optical device at point .4. Reverse the process to install the new device.Figure 6 - 4Removing the CD/DVD Device1 455551342
Upgrading The ComputerUpgrading the System Memory (RAM) 6 - 76Upgrading the System Memory (RAM)The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO-DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 fordetails of supported module types). The total memory size is automatically detected by the POST routine once you turnon your computer.1. Turn off the computer, and turn it over and remove the battery.2. Locate the RAM & CPU bay cover and remove screws - .1 43421Figure 6 - 5RAM & CPU Bay Screws
Upgrading The Computer6 - 8 Upgrading the System Memory (RAM)63. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover.4. Carefully disconnect the fan cable , and remove the cover .5. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & ) in Figure 6 - 7.5 6567 8Figure 6 - 6CPU/RAM Bay Cover RemovedContact WarningBe careful not to touchthe metal pins on themodule’s connectingedge. Even the cleanesthands have oils whichcan attract particles, anddegrade the module’sperformance.Figure 6 - 7RAM Module Release Latches78
Upgrading The ComputerUpgrading the System Memory (RAM) 6 - 966. The RAM module will pop-up, and you can remove it.7. Pull the latches to release the second module if necessary.8. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.9. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure.10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module.11. Replace the bay cover and screws (make sure you reconnect the fan cable before screwing down the bay cover).12. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.9Figure 6 - 8RAM Module Removal&Fan Cable Reconnection9
Upgrading The Computer6 - 10 Upgrading the Processor6Upgrading the ProcessorIf you want to upgrade your computer by replacing the existing processor with a fast-er/new one you will need to contact your customer service representative. We rec-ommend that you do not do this yourself, since if it is done incorrectly you maydamage the processor or mainboard.WarrantyThe CPU is not a userserviceable part. Open-ing this compartment, oraccessing the CPU inany way, may violateyour warranty.Unauthorized tamperingwith the HDD may alsoviolate your warranty.
Modules & OptionsOverview 7 - 17Chapter 7: Modules & OptionsOverviewThis chapter contains information on the following modules, which may come withyour computer, depending on the configuration purchased. If you are unsure pleasecontact your service representative.• PC Camera Module• 802.11 b/g USB WLAN Module• Bluetooth Module• 3.5G Module• Fingerprint Reader ModuleWireless Device Operation Aboard AircraftThe use of any portableelectronic transmissiondevices aboard aircraftis usually prohibited.Make sure the mod-ule(s) are OFF if you areusing the computeraboard aircraft. Important NoticeIf your purchase option includes both Wireless LAN and 3.5G modules, then the appropri-ate antennas will be installed. Note that In order to comply with FCC RF exposure compli-ance requirements, the antenna must not be co-located or operate in conjunction with anyother antenna or transmitter.
Modules & Options7 - 2 PC Camera Module7PC Camera ModuleThere are 3 camera options available for this computer, depending on your purchaseconfiguration. The 300K and 1.3M pixel camera modules use the BisonCap appli-cation to capture video files, and the 2.0M pixel camera module uses the VideoView application to capture video files.Before installing the PC Camera driver, make sure that the optional PC Camera ison. Use the Fn + F10 key combination (see Table 1 - 5, on page 1 - 10) to togglepower to the PC Camera module. Make sure you install the drivers in the orderindicated in Table 4 - 1, on page 4 - 3.Latest PC Camera Driver InformationCheck the CD, and anyaccompanying insertpages, for the latest up-dated information on thePC Camera driver,which may override theinformation providedhere.
Modules & OptionsPC Camera Module 7 - 37PC Camera Driver Installation1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click Optional (button).3. Click 1.PC Camera Driver, Web cam > Yes.For the 1.3M or 300K Pixel Camera Module:1. Choose the language you prefer and click Next > Next.2. Click Finish to restart the computer.3. Run the BisonCap application program from the BisonCam shortcut on the desktop, or from the BisonCam item in the Start > Programs/All Pro-grams menu (if the hardware is turned off use the Fn + F10 key combina-tion to turn it on again).For the 2.0M Pixel Camera Module:1. Click Install.2. Click to select Ye s or No in answer to the power system question.3. Click to select Ye s or No to enable/disable the Digital Zoom function.4. Click Finish > Finish to restart the computer.5. Run the Video View application program from the Video View shortcut on the desktop, or from the USB2.0 PC Camera item in the Start > Pro-grams/All Programs menu (if the hardware is turned off use the Fn + F10 key combination to turn it on again).
Modules & Options7 - 4 PC Camera Module7PC Camera Audio Setup (all camera modules)If you wish to capture video & audio with your camera, it is necessary to setup theaudio recording options in Windows.1. Click Start, and click Control Panel (or point to Settings and click Control Panel).2. Click Sound (Hardware and Sound).3. Click Recording (tab).4. Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled.5. Double-click Microphone (or select Properties from the right-click menu).6. Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to the level required.7. Click OK and close the control panels.8. Run the BisonCap application program from the Start > Programs/All Programs > BisonCam menu.9. Go to the Devices menu heading and select Microphone (Realtek....) (it should have a tick alongside it).10. Go to the Capture menu heading and select Capture Audio (it should have a tick alongside it).
Modules & OptionsPC Camera Module 7 - 57Figure 7 - 1Audio Setup for PC CameraRight-click
Modules & Options7 - 6 PC Camera Module7BisonCap (for 1.3M or 300K pixel camera modules)BisonCap is a video viewer useful for general purpose video viewing and testing,and can capture video files to .avi format.1. Run the BisonCap program from the Start > Programs/All Programs > Bison-Cam menu (it is recommended that you set the capture file before the capture process - see Set Capture File below).2. Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup (all camera modules)” on page 7 - 4) and select Start Capture.3. On the first run of the program (if you have not set the captured file) you will be asked to choose a file name and size (see the sidebar - Pre-Allocating File Space) for the captured file. Click Start Capture again.4. Click OK to start capturing the video, and press Esc to stop the capture.5. If you wish to, you may go to the File menu and select Save Captured Video As..., choose a file name and location, and then click Open (you can view the file using the Windows Media Player).Set Capture FileIn the BisonCap program you will only be asked to set the capture file name on thefirst run of the program. When you run the program the next time the file will auto-matically be overwritten with the newly captured file. To avoid overwriting files youcan go to the Set Capture File.. option in the File menu, and set the file name andlocation before capture. Set the name and location then click Open (you can chooseCancel to ignore the file size if prompted).Pre-Allocating File SpaceYou may pre-allocatethe file size for the cap-ture file in the BisonCapprogram. You canchoose to ignore this byclicking Cancel.Pre-allocating space onthe hard disk can im-prove the capture quali-ty (particularly of largecapture files), by reduc-ing the amount of workthe hard disk has to doin finding space for thevideo data as it is beingcaptured.
Modules & OptionsPC Camera Module 7 - 77Eliminating Screen Flicker (BisonCap)If you find that the video screen in the BisonCap program is flickering, you can tryto adjust the setting in the Video Capture Filter options.1. Run the BisonCap program.2. Go to Options and scroll down to select Video Capture Filter....3. Click either 50Hz or 60Hz under Frequency in Property Page (tab).Figure 7 - 2Video Capture Filter

Navigation menu