COBAN ELECTRONICS 302 GPS TRACKER User Manual

Shenzhen Coban Electronics Co., Ltd. GPS TRACKER

User Manual

Download: COBAN ELECTRONICS 302 GPS TRACKER User Manual
Mirror Download [FCC.gov]COBAN ELECTRONICS 302 GPS TRACKER User Manual
Document ID3470390
Application IDmLYQj6Z6LF/LGPO3Es0CaQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize120.86kB (1510786 bits)
Date Submitted2017-07-19 00:00:00
Date Available2017-07-19 00:00:00
Creation Date2017-06-28 09:18:20
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2017-07-11 17:21:25
Document TitleUser Manual
Document CreatorMicrosoft® Office Word 2007
Document Author: Administrator

GPS Tracker
Model:302 User Manual
Preface
Thank you for purchasing the tracker. This manual shows how to operate the device
smoothly and correctly. Make sure to read this manual carefully before using this
product. Please note that specification and information are subject to changes without
prior notice in this manual. Any change will be integrated in the latest release. The
manufacturer assumes no responsibility for any errors or omissions in this document.
Contents
1.
2.
3.
4.
5.
6.
Function Introduction ..................................................................................................4
Applications ................................................................................................................4
Hardware Description ..................................................................................................4
Accessories .................................................................................................................5
Specifications ..............................................................................................................6
Operating Instructions..................................................................................................6
6.1 Terminal Installation ............................................................................................6
6.2 SIM CARD Installations ......................................................................................7
6.3 Turn on the Tracker Device ..................................................................................8
6.4 GSM/GPS LED Indicator .....................................................................................8
6.5 Initialization.........................................................................................................8
6.6 Change Password .................................................................................................8
6.7 Authorization .......................................................................................................9
6.8 Single Locating ....................................................................................................9
6.9 Auto track continuously ..................................................................................... 10
6.9.1 Track with limited times upon time interval ............................................. 10
6.9.2 Track with unlimited times upon time interval ......................................... 10
6.9.3 Smart track upon time and distance interval ............................................. 10
6.10 Turning points update automatically ................................................................... 10
6.11 GPS drift suppression ......................................................................................... 11
6.12 Exact street address ............................................................................................ 11
6.13 Location based service (LBS) / Cell-ID Locating ................................................ 11
6.14 Monitor ............................................................................................................. 11
6.15 Data logging ...................................................................................................... 12
6.16 Data Load .......................................................................................................... 12
6.17 Forward the third parties’ message ...................................................................... 12
6.18 SIM card Balance Inquiry ................................................................................... 13
6.19 ACC working alarm ........................................................................................... 13
6.20 Cut off the Oil and Power System ....................................................................... 13
6.21 Calibration of fuel sensor ................................................................................... 14
6.22 Function of Remote Controller (Option, for model B ONLY)............................... 14
6.23 Arm ................................................................................................................... 15
6.24 Disarm ............................................................................................................... 15
6.25 Silent Mode ....................................................................................................... 15
6.26 Decide how many times of alarm message .......................................................... 16
6.27 Alarms ............................................................................................................... 16
6.27.1 Low battery alarm ................................................................................... 16
6.27.2 Power off alarm ...................................................................................... 16
6.27.3 GPS blind Spot alert ............................................................................... 16
6.27.4 SOS........................................................................................................ 16
6.27.5 Geo-fence ............................................................................................... 17
7.
8.
6.27.6 Multi-area management........................................................................... 17
6.27.7 Movement alarm ..................................................................................... 18
6.27.8 Over speed alarm .................................................................................... 18
6.27.9 Fuel alarm .............................................................................................. 18
6.28 Alarms under Arm State ..................................................................................... 18
6.28.1 Door open alarm ..................................................................................... 18
6.28.2 ACC Alarm ............................................................................................ 18
6.28.3 External Shock Sensor alarm(Optional) ................................................... 19
6.28.4 Built in Acceleration Sensor Alarm .......................................................... 19
6.28.5 Built in Shock sensor sensitivity configuration ......................................... 19
6.28.6 Alarm without GSM network service....................................................... 19
6.29 Sleep Mode........................................................................................................ 19
6.30 Check the Vehicle State ...................................................................................... 20
6.31 Check IMEI ....................................................................................................... 21
6.32 Terminal (local) Time Setting ............................................................................. 21
6.33 Reset Hardware .................................................................................................. 21
6.34 Configure parameters by USB ............................................................................ 21
6.35 GPRS Setting ..................................................................................................... 21
6.36 Less GPRS traffic .............................................................................................. 22
6.37 Activate "Fuel" value in GPRS data .................................................................... 23
6.38 Instructions for web platform and mobile APP .................................................... 23
Cautions .................................................................................................................... 29
Faults & the Solutions................................................................................................ 29
1. Function Introduction
1.1. This tracker is a new product based on the GSM / GPRS network and GPS satellite
positioning system, which set multiple functions of security, positioning, monitoring
surveillance, emergency alarms and tracking in its entirety. It can track and monitor
remote target by SMS or internet.
1.2. Features
1.2.1 Support both GPS & LBS (Location based service).
1.2.2 Support SMS/GPRS/Internet Network data transmission
1.2.1 Support GPRS on-line and GPRS re-connected automatically if GPRS
drops
1.2.3 Support SMS / GPRS dual-mode switching
1.2.4 Support configuration by remote terminal.
1.2.5 Support for point-to-point, point to group, group-to-group monitoring.
1.2.6 Set multiple functions of security, positioning, monitoring surveillance,
emergency alarms and tracking in its entirety.
2. Applications
Used widely for vehicle and other moving objects tracking.
3. Hardware Description
① GSM Antenna connector
② SIM card slot
③ SIM card slot Pop-up switch
⑦ Shock sensor port
⑧ Harness Port
⑨ GSM/GPS LED
④ MicroSD slot
⑩ Backup battery switch
⑤ Monitor microphone jack
11
○
⑥ GPS Antenna connector
Remote controller antenna
(Optional for Model B only)
4. Accessories
No.
photoes
NAME
note
GPS Antenna
2 meters
GSM Antenna
2 meters
Microphone
1.5 meters
Harness
10PIN
Relay
12V/40A to 24V/40A
according to vehicles
Shock sensor
Option for both model A and
Siren
Option for both model A and
Remote controller
Option for model B ONLY
9
Fuel Sensor
Option for both model A and
5. Specifications
Content
DIM.
Weight
Network
Band
GPS Sensitivity
GPS Accuracy
specifications
83*54*26mm
120g
GSM/GPRS
850/900/1800/1900Mhz
-159dBm
5m
GPS Start time
Cold status 45s
Warm status 35s
Hot status 1s
Voltage
12 V -24V
Backup battery
Storage Temp.
Chargeable 3.7V350mAh Polymer Li-Battery
-40°C to +85°C
Operation Temp.
Humidity
-20°C to +65°C
5%--95% non-condensing
6. Operating Instructions
6.1 Terminal Installation
6.1.1 Please ask the qualified engineers to install it.
6.1.2 Do not install it in an environment which is over GSM performance index, and
please pay attention to fix the antennas in an appropriate position with good signals.
6.1.3 Pay attention to make installation location preventing water and dust.
6.1.4 Find the 10 PIN harness and insert it into the corresponding holes of the products,
and connect the wires with the original car circuit showing below:
Wiring diagram
Note: The orange wire can be connected to the original car horn; it can also be
connected to the siren you buy with the tracker. (Siren is Option)
6.1.5 Knowing about the type of the door trigger is positive or negative trigger. Please
connect the green wire to the door control circuit if it is positive, and connect blue
wire if it is negative.
6.1.6 Please put SOS button at the place driver can touch.
6.1.7 Insert the shock sensor plug into the sensor jack. (Shock sensor is Option)
6.1.8 Insert the external monitor Microphone into the monitor jack.
6.1.9 Connect the GPS and GSM antenna to the right connector, and find an appropriate
place to fix the antennas to make sure it receives signals well.
6.2 SIM CARD Installations
6.2.1 Use a tweezers or a sharp thing to touch the SIM CARD popup
switch,
the SIM CARD slot will pop up, take out the SIM card slot and put SIM card in it. And
then put the SIM card slot back to its original position after confirm the SIM card in the
right place.
6.2.2 Please make sure the SIM card is for GSM network and able to execute the function
of incoming calls display, no calls can be diverted and the PIN code is locked. The SMS
format must be TXT format, and can’t recognize the PDU format.
6.3 Turn on the Tracker Device
Connect the positive and negative wire, red and black ones, with 12V or 24V car power
system, wait for 1 minute after connecting power to wait tracker works normal, and
then turn on the backup battery switch.
6.4 GSM/GPS LED Indicator
LED Indicator Type
Red LED
Green LED
Behavior
ON
Flash quickly, 1 time
per second
Flash slowly, 1 time
per 3 seconds
ON
OFF
Meaning
No GSM signal
GSM mode with good reception
GPRS mode
Fix to satellites
Lost fix to satellites
6.5 Initialization
Send SMS “begin+password” to the unit, it will reply “begin ok” and initialize all the
settings to default factory settings.(default password: 123456)
For example: send SMS “begin123456”, it will reply “begin ok”. (No quotation marks“”
when sending all the SMS)
6.6 Change Password
6.6.1 Send SMS “ password+old password+space+new password” to the unit to change
the password.
For example: send SMS “password123456 888888” to the unit. If succeeded,
“password ok” will reply to your cell phone from the device tracker.
6.6.2 Be sure to keep the new password in mind, you have to upload the software to restore
the original setting in case of losing the new password.
6.6.3 Attention: Make sure the new password is in 6 digits Arabic numbers, or else the
tracker cannot recognize the password.
6.6.4 When reading this user manual, you will notice that we have used "+" and "space"
between some words;"+" between two words means they should be written together as
one word and "space" between two words means you should leave one character space
between two words.
6.7 Authorization
6.7.1 You must setup the authorized phone number before using SOS, geo-fence alarm, etc.
Up to 5 numbers can be authorized.
6.7.2 Call the tracker for 10 times continuously and get its position, then it will save the cell
phone number as the authorized number automatically. and reply “add master ok”.
6.7.3 Authorization: Send SMS “admin+password+space+cell phone number” to set up an
authorized number, the other authorized numbers should be set by the first authorized
number, if the number is successfully authorized, the unit will reply “ admin OK” by
SMS.
6.7.4 Delete authorization: Send SMS “noadmin+password+space+authorized number” to
delete the authorized number.
6.7.5 If you want to track the target when it enters into another country, you must add the
country code before the cell phone number. You should authorize your number in
international format as follows: “admin123456 008613322221111” to tracker to set
13322221111 as an authorized number.
6.8 Single Locating
6.8.1 If there aren’t any authorized number set-up, it will reply all calls with a location
report; if there are authorized numbers set-up, then it will not respond when an
unauthorized number calls it.
6.8.2 If you call it from authorized phone number, it will hang up and report a real-time
location as below:
6.8.3 When lost fix to satellites, it will track by LBS / CELL-ID. And the SMS will include
two positions:
 GPS coordinates of the last known position.
 LAC code. Open web platform and find “manual track”, put code received from tracker
in LAC and Cell-ID fields to locate by LBS technology.
6.9 Auto track continuously
6.9.1 Track with limited times upon time interval
Send SMS command “fix030s005n +password” to the tracker device, it will report
the latitude & longitude at intervals of 30 seconds for 5 times. (s:second, m:minute,
h:hour). This command set must be in 3 digits Arabic numbers and the maximum
value is 255.
e.g. fix030s005n123456
6.9.2 Track with unlimited times upon time interval
Send SMS “fix030s030m***n+password” to the tracker. Tracker will report a
real-time location every 30 seconds when ACC is ON, and report every 30 minutes
when ACC is OFF.
Note: The interval must not less than 10s.
6.9.3 Smart track upon time and distance interval
6.9.3.1 Please set "track with unlimited times upon time interval" before this function, and
send "distance+password+space+distance", tracker will reply "Distance ok", and
then tracker will locate upon both the pre-set time and distance.
e.g. Send "distance123456 0050", it means distance is 50 meters; the number must
be 4 digits Arabic numbers.
6.9.3.2 Set this function on web platform: Set time interval first and then distance interval,
tracker will locate upon the time and distance.
6.9.3.3 Cancel: Send SMS “nofix+password” to the tracker device to cancel the “auto track”.
e.g. nofix123456
6.10 Turning points update automatically
6.10.1 The tracker will update the positions automatically to web platform once the vehicle
changing driving direction over pre set angle value to form a smooth trajectory
consistent with the actual road, this function is only effective in GPRS mode.
6.10.2 Send "angle+password+space+angle" to tracker, it will reply" angle ok".
e.g.
angle123456 040
6.10.3 The angle must be 3 digits Arabic numbers, default angle value is 30 degree.
6.11 GPS drift suppression
6.11.1 This function is deactivated by default, to activate this function, send SMS
"suppress+password" to tracker, it will reply" suppress drift ok". The GPS data
stop updating if vehicle is not driving (ACC is OFF) and latitude and longitude
always keep same, and GPS data updates automatically when vehicle is moving.
6.11.2 Cancel: send "nosuppress+password" to tracker, it will reply" nosuppress ok ".
6.12 Exact street address
6.12.1 You must set up the APN of your local GSM network for the SIM card in
tracker first before using this function, if there is user name and password for
GPRS
login, Please refer to 6.35.1 & 6.35.2 section of this manual to configure the APN, user
name and password for GPRS login.
6.12.2 After configure the APN, send "address+password" to device, it will reply SMS
including real street/address name. For example: No.113, Guankou 2nd Rd, Nantou,
Nanshan district, Shenzhen, Guangdong, china.
6.13 Location based service (LBS) / Cell-ID Locating
If the tracker cannot establish a solid GPS Fix, it will calculate its location using
Cell-ID GSM locating, Location reports will include the GPS coordinates of the last
known positions as well as a LAC code, Entering the LAC code to the “Manual
Track” menu of web tracking platform www.gpstrackerxy.com will enable you to see
the tracker’s current location. You can also send command “address+password” to the
tracker to request exact address, track will automatically switch to tracking by LBS in
GPRS mode. Accuracy of LBS depends on the distance to the nearest GSM Network
Cell Tower or Base Station.
Note: This feature can be used normally in most areas according to the signal of GSM
network. It may not be available in some areas.
6.14 Monitor
6.14.1 The command to switch between Tracker mode and Monitor mode are “tracker” and
“monitor”.The default mode is “tracker” (Track mode).
6.14.2 Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and
switch to “monitor” mode.
6.14.3 Send SMS “tracker+password” to the unit, and it will reply “tracker ok!” and switch
to “tracker” mode.
6.15 Data logging
6.15.1 Auto logging:When the tracker device lost GSM signals or fall offline from GPRS,
tracker will log the tracking position and alerts automatically in the SD card on the basis
of the pre-set condition, when GSM signals get back, all the event alerts will be auto-sent
to the authorized numbers or web platform (server), but the logged tracking data should
be loaded to the web platform via SMS command.
6.15.2 Logging upon times: Send SMS: “save030s005n+password” to the tracker unit, it
will reply “save ok”, and will log the Latitude and longitude locations every 30 seconds
for 5 times. (S: second, m: minute; h: hour).
6.15.3 Multi-logging:Send SMS:”save030s***n+password” to tracker device, it will reply
“save ok”.
6.15.4 Cancel logging: Send SMS “nosave+password”, e.g. nosave123456
6.15.5 Logging Clearance: send SMS: “clear+password” to tracker device, it will reply
“clear ok”.
6.15.6 Logging Volume: It depends on the capacity of the SD card inserted in the tracker
device.
6.15.7 The logged data in SD card can be copied to computers through card reader, and then
the data route can be checked by importing data in the menu “Data Import” of web
platform www.gpstrackerxy.com
6.16 Data Load
6.16.1 Current date Load: Send SMS: “load+ password” to tracker device, it will reply:
“load ok” if the device is working well under GPRS mode; if not, it will reply “load fail!
Please check gprs” that means device does not work under GPRS mode.
6.16.2 Specified date Load: Send SMS: “load+ password+ space+ year month date” to
tracker device, it will reply: “load ok” and load the tracking data to the web platform
upon the valid time you choose. For Example: send SMS: “load123456 20110425” to the
tracker device, means to load the tracking data of 25th April 2011 to web platform.
6.17 Forward the third parties’ message
6.17.1 Send SMS "forward+password+space+third parties phone number" from authorized
phone number, tracker will reply"forward ok", and supports 1 third
parties phone
numbers at most.
For example, set the phone number of the service provider of the SIM card in the tracker,
when charge remind message coming in, tracker will forward it to authorized phone
number.
6.17.2 Cancel: Send SMS command "noforward+password".
6.18 SIM card Balance Inquiry
6.18.1 Send SMS command "balance+password+space+carrier’s phone
number+space+code" to tracker, it will forward the code to carrier’s phone number and
return the balance message received from carrier’s phone number.
6.18.2 How it works: After accept balance command, tracker will remember the “mobile
phone number”, carrier’s phone number and the code;
6.18.3 And then send the code to carrier’s phone number, and forward the message from
carrier to mobile phone number.
Take china mobile for example, mobile users can send “ye” to china mobile number
10086, and 10086 will send user’s balance message to tracker, and then tracker forward
the balance message to mobile phone number , following is an illustration how this
function works.
Received and execute
Mobile
balance123456 10086 ye
Forward balance message to mobile phone
Send ye out to 10086
Tracker
10086(China mobile)
Send balance back
Received Balance message
Received ye from number in the
tracker and process
6.19 ACC working alarm
6.19.1
This function is deactivated by default. To active this functions, send
"ACC+password" to tracker, it will reply "ACC ok". And tracker will send "ACC
on+latitude & longitude" to authorized numbers when detect ignition on, that means the
vehicle has been started; and tracker will send “ACC off+latitude & longitude" to
authorized numbers when ignition off and ACC is off, that means vehicles has been
stopped.
6.19.2
Send "noACC+password" to deactivate this function, tracker will reply "noACC
ok".
6.19.3
This configuration can only activate and deactivate the alarm to authorized
numbers; it will send to web platform automatically in GPRS mode and can't be
deactivated.
6.20
6.20.1
Cut off the Oil and Power System
Send command “stop+password” to tracker, tracker will execute it and reply
“Stop engine Succeed”. And it will remain immobile state until next command to
resume.
6.20.2
Stop mode
Execute immediately: Send command “quickstop+password” to tracker, it will reply
“quickstop OK”. Then tracker will stop the car immediately after “stop” command.
Execute depends on speed(Default mode): Send command “noquickstop+password” to
tracker, It will reply “noquickstop OK”, Then the tracker won’t stop the car
immediately after “stop” command, instead, it will reply “it will be executed after speed
less than 20KM/H”, and stop the car when the speed is less than 20KM/H.
6.20.3
Resume the Oil and Power System
Send “resume+password" to tracker, it will reply "Resume engine succeed", it means
the oil supply is resumed .
6.21 Calibration of fuel sensor
6.21.1
Due to the different height of fuel tank and fuel level sensor specifications,
tracker need to set an appropriate zero value and full range value to detect the precise
fuel percentage.
6.21.2
Zero calibration: Send “ oilzero+password “ to tracker when the fuel tank is
empty , tracker will adjust to zero and reply “ oilzero ok!” . The fuel value is 0%.
6.21.3
Full calibration: Send “oilfull+password “ to tracker when the fuel tank is full ,
then tracker will adjust to full range and reply “ oilfull ok! “ . The fuel value is 100%.
6.22 Function of Remote Controller (Option, for model B ONLY)
Button
Function
ARM
DISARM
ARM &
Silent
mode
SOS
Deterrence/
car
search
Descriptions
Press for 0.5 second, the siren will beep one time.
Press for 0.5 second, the siren will beep two times.
Press for 0.5 second when it is in disarm state, the siren will
beep one times. No voice from siren when alarm triggered and
quit from silent mode automatically when disarm.
Press for 3 seconds, Tracker will send SOS alert to authorized phone
numbers without voice.
Press for 0.5 second when it is in arm state, siren will beep 10
seconds, press disarm button
to quit.
6.23 Arm
6.23.1 Set up arm by SMS
Send SMS command “arm+password” to the tracker device in the vehicle. It will reply
“Tracker is activated” in both armed and disarmed state, and the SMS command will
make the tracker device enter into armed state if the unit currently disarmed.
User must stop the engine, (that is ACC is lower voltage).Sending SMS
“arm+password” when close the door and left. You will set up arm status fail if the
engine is turned on (the ACC is high voltage), it will reply “set up fail! pls turn off
ACC”
6.23.2 Set up arm by remote controller (Option, for model B ONLY)
button on the remote controller for 0.5 seconds, the car enters into armed
Press
state and the siren will beep one time, no SMS reply.
6.24 Disarm
6.24.1 Disarm by SMS
Send SMS command "disarm + password" to the tracker device in the vehicle, It will
reply “Tracker is deactivated” in both armed and disarmed state, and the SMS command
will make the tracker device enter into disarmed state if the unit currently armed.
It won’t alarm if the door is open and sensor is vibrated and the engine is started when
arm function is deactivated .
6.24.2 Disarm by remote controller (Option, for model B ONLY)
button on the remote controller, the car enters into disarm state, and the siren
Press
will beep two times, no SMS sent.
6.25 Silent Mode
6.25.1 Set up silent mode by SMS
Send SMS “silent+password” to tracker device, it will reply “silent ok!”. It means
tracker device enters into silent mode, siren won’t be sound after alarm is triggered, but
tracker will send alarm SMS to authorized number.
Send disarm command “disarm+password” to quit silent mode .
6.25.2 Set up silent mode by remote controller (Option, for model B ONLY)
Press
in disarm state for 0.5 second, the siren will beep one
time, Tracker device enters into silent mode, siren won’t be sound after alarm is
triggered, but tracker will send alarm SMS to authorized numbers.
Press
to quit silent mode.
Decide how many times of alarm message
6.26
You can decide how many times of the alarm message to be sent, For those alarm
message sent in cycle, you can limit the times the alarm message to be sent. send SMS
“ xtime+password+005 “ to tracker, alarm message will be sent 5 times once alarms are
triggered .
Alarm SMS will be sent 5 times by default.
6.27 Alarms
6.27.1
Low battery alarm
6.27.1.1 Send SMS “lowbattery+password+space+on”, it will send SMS “low
battery+latitude/longitude” to authorized numbers 2 times in total in 15 minutes interval
when voltage of battery is going to be about 3.55V.
6.27.1.2 This function activates by default, send SMS “lowbattery+password+space+off”
to deactivate.
6.27.2
Power off alarm
6.27.2.1 Send “ extpower+password+space+on” to activate, it will send SMS “power
alarm+latitude/longtitude” to authorized numbers every 3 minutes when external power
is cut off.
6.27.2.2 This function activates by default.
Cancel: Send SMS “ extpower+password+space+off” to deactivate it.
6.27.3
GPS blind Spot alert
6.27.3.1 This function deactivates by default, send SMS
“gpssignal+password+space+on”, it will send alert SMS “no gps+last valid
latitude/longitude before lost signal”
6.27.3.2 Send SMS “gpssignal+password+space+off” to deactivate.
6.27.4
SOS
Long Press the SOS button for 3 seconds(For model B, press
button on remote
controller for 3 seconds), the tracker device will send SMS “help me!+lat./long.” to all the
authorized numbers at interval of 3 minutes. It will stop sending such a SMS when any
authorized number reply SMS “help me!” to the tracker.
6.27.5
Geo-fence
6.27.5.1 Set up a geo-fence for the tracker device to restrict its movements within a
district. The unit will send SMS to the authorized numbers when it goes out of this
district.
6.27.5.2 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can
send
SMS“stockade+password+space+latitude,longitude;latitude,longitude” to unit to set the
restricted district. In case of breach, it will send SMS “stockade!+ latitude & longitude”
to the authorized numbers.
Remark: The first latitude & longitude is coordinate of the top left corner of the
Geo-fence, while the second latitude & longitude is the coordinate of the bottom right
corner, it will send alarm SMS at interval of 3 minutes once beyond the restricted
district.
6.27.5.3 Cancel: Send SMS “nostockade+password” to deactivate this function.
6.27.6
Multi-area management
6.27.6.1 Set Area
Send SMS command
"area+password+space+latitude,longitude+space+areaname,distanceM" to
tracker(distance unit: M for meter, K for kilometer), it will reply "area01 ok".
Example: Send "area123456 22.353648,113.543678 school,800M".
Note: 5 areas at most and the distance between two points can't be less than the total
distance in the 2 commands, and different areas can't cover each other.
6.27.6.2 Delete areas
Send SMS command:"noarea+password+space+area name", tracker will reply:"noarea
ok".
6.27.6.3 Rename and set distance
Send SMS command "rename+password+space+old name;new name,distanceM" to
tracker, if name is not repeated and area doesn't cover others, it will reply "rename ok!"
for successful configuration.
Example: Send"rename123456 area01;school,800M", it means the new area name is
"school", and covers area of a radius of 800 meters.
6.27.6.4 Activate multi-area management
Send SMS command "area+password+space+on" to tracker, it will reply "Area
on ok!", when tracker enter the pre set area, it will send SMS "area
name+latitude & longitude" to all the authorized phone number, and send same
SMS when goes out of the area.
6.27.6.5 Deactivate Multi-area management
Send SMS command "area+password+space+off" to tracker, it will reply"area off ok!"
6.27.7
Movement alarm
6.27.7.1 Set up: when the unit stays immobile in a place for 3-10 minutes with GPS
signal reception, the user can send SMS“move+password+space+0200” to the tracker
(Suppose area of a radius of 200 meters, it supports 4 digits at most. Unit: Meter). It
will reply “move OK”. In case of such a movement (the default distance is 200m), it
will send SMS “Move+ latitude & longitude” to the authorized numbers at interval of 3
minutes.
6.27.7.2 Cancel: Send SMS “nomove+password” to deactivate the movement alarm.
6.27.8
Over speed alarm
6.27.8.1 Set up: Send SMS “speed+password+space+080” to the unit (suppose the speed
is 80km/h), and it will reply “speed OK!”. When the target moves exceeding 80km/h,
the unit will send SMS “speed+080!+ latitude & longitude” to the authorized
numbers ,it will only send one SMS in 3 minutes in SMS mode when overspeed ; the
siren will beep 1 time when overspeed 1 time.
6.27.8.2 Cancel: Send SMS “nospeed+password” to deactivate the overspeed alarm.
Remark: The recommended speed should be not less than 30km/h. For below that rate, it
will be effected the accuracy by GPS signals drift etc.
6.27.9
Fuel alarm
6.27.9.1 When the fuel consumption exceeds the normal standards during driving, or oil
theft/leakage when the vehicle is stopped, the tracker will send "oil: xx% + Geo-info"
to the authorized number at interval of 3 minutes. The horn beeps 20S.
6.27.9.2 Cancel: Send SMS command “ nooil+password” to tracker.
6.28 Alarms under Arm State
6.28.1
Door open alarm
The unit will send SMS “Door alarm+lat/long” to the authorized number at interval of 3
minutes when the door of the car opens in arm status. Siren will be sound for 20 seconds,
and repeat sound at interval of 20 seconds minutes if the door is always open. Disarm to
stop this alarm
6.28.2
ACC Alarm
The unit will send SMS “ACC alarm+lat/long” to the authorized number in at interval of
3 minutes when the engine of the car is turned on, that is the key is rotated to “ACC
ON” position to start the car in arm state; Siren will be sound for 20 seconds, and repeat
again at interval of 20 seconds if the ACC always keep ON.
Disarm to stop this alarm
6.28.3
External Shock Sensor alarm(Optional)
The unit will send only one alarm SMS “Sensor alarm+lat/long” to the authorized
number in 3 minutes when the sensor is triggered in arm status. Within 3 minutes, the
alarm siren sound for 5 seconds when the vibration is detected in the first time and
second time. The alarm siren sound for 10 seconds when vibration again. If you disarm
the tracker, the times will reset.
Disarm to stop this alarm.
6.28.4
Built in Acceleration Sensor Alarm
The tracker is built in three axis acceleration sensor, the tracker can detect it in arm state
when the vehicle move, tilt or shock. The alarm way is same as the external shock
sensor alarm.
Disarm to stop this alarm.
6.28.5
Built in Shock sensor sensitivity configuration
The sensitivity of the built-in shock sensor has three different level:
First level: Alarm will be triggered after detect slight vibration, send command"
sensitivity+password+space+1" .
Second level: Alarm will be triggered after detect 8 times vibration in 2 seconds, send
command" sensitivity+password+space+2".
Third level: Alarm will be triggered after detect 25 times vibration in 5 seconds, send
command" sensitivity+password+space+3".
6.28.6
Alarm without GSM network service
When the car is in the place without GSM network service, siren will be sound under
non-silent mode if alarm is triggered (door, sensor, ACC), but no SMS alarm will send to
authorized number.
6.29 Sleep Mode
SMS Mode
GPRS Mode
Set Less GPRS Traffic in GPRS Mode
No
Sleep
Sleep
Work
Online
ACC off. No Calling,
SMS and any
triggered alarm, go to
sleep, GPS module
shut off, GSM
module work in low Online
power consumption.
ACC On or Calling,
SMS and any
triggered alarm can
awake it.
ACC Off. No Calling, SMS and any
triggered alarm, GPRS disconnect and switch
to SMS mode, sleep. ACC on or Calling,
SMS and any triggered alarm can awake it,
and GPRS connect
ACC Off. No Calling, SMS and any triggered
alarm, GPRS disconnect and switch to SMS
mode, go to sleep. ACC on or Calling, SMS
and any triggered alarm can awake it, and
GPRS connect.
6.29.1 This function is deactivated by default, send “sleep+password+space+on”, tracker
will reply “sleep on ok”. When vehicle is not driving (ACC is OFF), GSM module fall
asleep; GPS module shut off; and tracker works in low power consumption. Calling,
SMS command and any triggered alarm can awake it.
6.29.2 Cancel: Send “sleep+password+space+off”, tracker will reply “sleep off ok”, tracker
won’t sleep, GSM and GPS works all the time.
6.30 Check the Vehicle State
Send SMS command “check+password” to the tracker in the vehicle, It will reply SMS
as follows:
Power: ON/OFF
Battery: 100%
Oil: 100%
GPRS: ON/OFF
GPS: OK/NO GPS
ACC: OFF/ON
Door: OFF/ON
GSM Signal: 1-32
Note: The higher digit it shows; the better.
APN: cmnet
IP: 104.250.138.146
PORT: 9000
6.31 Check IMEI
Send SMS command "imei+password" to the device. E.g: Send SMS command
"imei123456" to the tracker device, it will reply an IMEI number in 15 digits to
your cell phone.
6.32 Terminal (local) Time Setting
6.32.1 Send SMS command “time+space+zone+password+space+time” to the device,
If succeed, it will reply “time OK”
6.32.2 For example: Send SMS “time zone123456 8”, 8 is Chinese time zone, If your
country time zone is minus, send SMS “time zone123456 -8”.
6.33 Reset Hardware
Send SMS “reset+password” to tracker device to reset the GSM module and
GPS module of the tracker device, it will reply “reset ok”.
6.34 Configure parameters by USB
Connect tracker to computer with the optional USB cable, open the memory
of the tracker, find and open the initial configuration file with
notepad
, operate according the instructions.
Note: Correct password is needed every time you configure the tracker.
6.35 GPRS Setting
User must send SMS via cell phone to set up APN, IP and port before starting
tracking by GPRS.
6.35.1 Configure APN
APN standards for Access Point Name and differs from country to country. For more
information about your local APN, please inquire with your local GPRS network
operator.
Send a SMS command to tracker “APN+password + Space + your local APN” via a
cell phone and if succeeded, the tracker will reply “APN OK”.
For example: Send SMS command “APN123456 CMNET”. If succeeded, the tracker
will reply “APN OK”.
Notes: 123456 refer to password of tracker and CMNET is the
APN of one of china GPRS Network Operator (China mobile).
6.35.2 GPRS User Name and password Setup
6.35.2.1 In most countries, the user name and password involving GPRS login are not
compulsorily necessary, therefore, the entry can be skipped. As for those countries
require user name and password, please configure as following:
6.35.2.2 Send SMS “up+password+space+user+space+password” If succeeded, the
tracker will reply “user, password ok!”
6.35.2.3 For instance, send SMS “up123456 web webgprs” to the tracker, and if
succeeded, tracker will reply “user, password OK”
Note: 123456 is password for the tracker, web is the user name for GPRS login,
webgprs is the password for GPRS login.
6.35.3 IP and Port Setup
6.35.3.1 Send SMS as below via a cell phone: “adminip+password+Space+IP
Address+Space+Port Number”. If succeeded, tracker will reply “adminip OK”.
6.35.3.2 For example: Send SMS command “adminip123456 202.104.150.75 9000” to
the tracker, If succeeded, it will reply “adminip OK”. ( 123456 is default password,
202.104.150.75 is IP,9000 is port).
6.35.4 Switch to GPRS mode
6.35.4.1 The default mode is “SMS”, Send SMS “GPRS+password” to the tracker, and it
will reply “GPRS ok!” it means the tracker has switched to “GPRS” mode.
6.35.4.2 TCP and UDP switch
Command: "gprs+password,0,0" switch to TCP mode, this is the default mode.
Command:"gprs+password,1,1" switch to UDP mode.
6.35.4.3 Send SMS “SMS+password” to the tracker, and it will reply “SMS ok!” and
restore to “SMS” mode.
6.36 Less GPRS traffic
6.36.1 Tracker will change to less GPRS traffic mode after parking 5 minutes (ACC is
OFF), GPRS disconnect and connect again when alarm being triggered or vehicle starts
driving.
6.36.2 Activate this function: Send "less gprs123456 on", tracker will reply "less gprs on
ok".
6.36.3 Deactivate this function: Send "less gprs123456 off", tracker will reply" less gprs off
ok".
Note: 123456 is the password of tracker, and replace it with the new if you have changed.
6.37 Activate "Fuel" value in GPRS data
The default format of GPRS data doesn't include "Fuel" value, if you need "Fuel"value,
please send “protocol+password 18” to tracker, if succeed, it will reply "protocol 18 ok";
send “protocol+password 12” to change back to default mode, if succeed, it will reply
"protocol 12 ok".
6.38 Instructions for web platform and mobile APP
Users need to regsiter an account on www.gpstrackerxy.com before use web or APP platform,
account name and password is the same on web/APP platform
6.38.1 register an account
1 、 choose the right
server to login in
2、Validate your IMEI is
valid or not
3、Click "register". Pop-up a
dialog box, register an
account
6.38.2 Login
4、Input the newly registered
user ID and password,
click "login"
6.38.3 Add a terminal
5、add terminal
6、add terminal
7.enter IMEI
8. name
9、choose location icon
10、save
11 .the newly registered device is
offline in grey color
6.38.4 Configure your tracker to web platform to track it online
step 1:set APN,refer to 6.35.1
Step 2:set GPRS user name and password,refer to 6.35.2
Step 3:set IP and port, please use the corresponding IP and port of the server you choose,
refer to 6.35.3
Step 4:switch to GPRS mode,refer to 6.35.4
12. After receiving GPRS OK, wait about one
minute, tracker will be online in green
color, you can operate the tracker,
6.38.5 If the tracker is always offline (grey color), make sure the SIM card subscribe the
GPRS service,
and have money to surf the Internet, you can use phone to test the sim card can surf the
Internet or not
please check the APN, user name, password, IP, port settings are correct, refer to 6.30.
6.38.6 IOS &Android mobile APP
6.38.6.1 Download and install the mobile APP software
According to your phone type, download and install mobile app below the home page
on web tracking platform
6.38.6.2 Login in and use the mobile APP under GPRS version
2. Filling the
registered user
ID and
password
1. CHOOSE
GPRS
3.Choose the
right server
4.Click”login”
5. Click here to operate
the device
6.38.6.3 login in and use the mobile APP under SMS version
2.Use”mc” as the
initial user
ID,password is 8888,
change the user name
and password after
entry
1.Choose
SMS LOGIN
4. Choose “add device”
5. Filling the device
name
6. Choose the type
7. Filling the SIM
PHONE NUMBER
8. Filling the tracker’s
password
9. Click “ok”
3.Click “login”
10. Click the icon, and
display the list
11. Click here to
operate the device
13.Click to send
commands
14.Filling
parameters
manually and
then click “send”
12.Click here
Remarks: APP on Android phone can track the address and show alarm by SMS; IOS APP
can only send commands due to the confined policy
7. Cautions
Please comply with the instructions to extend the unit life:
1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside
circuitry.
2. Don’t use & store the unit in dusty places.
3. Don’t put the unit in overheated or overcooled places.
4. Handle carefully. Don’t vibrate or shake it violently.
5. Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
6. Don’t paint the unit, this may cause some foreign materials left in between the parts.
7. Don’t disassemble or refit the unit.
8. Please read the user manual carefully before installation and operation, learn something
more about the voltage range. Otherwise, it won’t work properly or destroy the product.
8. Faults & the Solutions
Faults
Solution
Fail to turn it on
Please check if built-in battery is charged, and power wires
connected well.
No GSM signal





No GPS
Please check if GPS antenna connected well, and recommend GPS
antenna be installed near the window glass, no metal parts can
cover it to make sure better GPS signal reception.
No reply to SMS
command
Password wrong or the format is wrong.
No reply to calling
Authorized / admin phone number is incorrect
不能收到报警短信
No alarm message
Authorized / admin phone number has not setup
Please check if SIM card installed correctly.
Please check if SIM card is GSM network.
Don’t turn on the PIN code
no calls can be diverted
Please check if voltage of the power is normal
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this
device does not cause harmful interference.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure
limits, Human proximity to the antenna shall not be less than 20cm (8 inches) during normal
operation

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Administrator
Create Date                     : 2017:06:28 09:18:20+08:00
Modify Date                     : 2017:07:11 17:21:25+08:00
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Administrator
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2017:07:11 17:21:25+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:45f4be3c-9280-4583-b3f2-278a398f8523
Instance ID                     : uuid:b282268a-0822-41ab-9a06-f6de281deffe
Page Count                      : 30
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AA64-302

Navigation menu