Cabletron Systems Els10 26Tx Users Manual

2015-02-05

• Title Page
• Notice
• Contents
• Introduction
  • 1.1 About This Manual
  • 1.2 Getting Help
  • 1.4 Related Documentation
  • 1.5 Overview
    • 1.5.1 SmartSTACK 10 ELS10-26 Architecture
      • Store and Forward Switching
      • Discarding Local Traffic
      • Spanning Tree Algorithm
    • 1.5.2 SmartSTACK 10 ELS10-26 Bridge Address Tabl...
    • 1.5.3 SmartSTACK 10 ELS10-26 Port Monitoring
      • Packet Capturing and Monitoring
    • 1.5.4 SmartSTACK 10 ELS10-26 Sample Applications...
      • SmartSTACK 10 ELS10-26 Trunking
      • SmartSTACK 10 ELS10-26 Fast Ethernet
      • Virtual Workgroups
  • 1.6 Local Console Manager
    • 1.6.1 Command Syntax Conventions
    • 1.6.2 Basic LCM Commands
      • Help
      • Erase
      • Exit or Logout
      • Traplog
• Unpacking and Installing Your ELS10-26
  • 2.1 ELS10-26 Front Panel
  • 2.2 Installing an FEPIM
  • 2.3 Installing the ELS10-26
    • Rack-mounting an ELS10-26
  • 2.4 Checking the Power-up Diagnostics 2.4 Sequ...
  • 2.5 Connecting the Local Console Manager
  • 2.6 Connecting to the Network
    • 2.6.1 Connecting UTP Cables
    • 2.6.2 Connecting a UTP Segment to the FE-100TX
    • 2.6.3 Connecting a Multimode Segment to the FE-1...
      • Fiber Optic Network Connection
• Configuring Your ELS10-26
  • 3.1 Assigning IP Addresses
    • 3.1.1 Displaying IP Addresses
    • 3.1.2 Deleting an IP Address
    • 3.1.3 Changing a Subnet Mask
  • 3.2 Enabling Bridging
  • 3.3 Disabling Bridging
  • 3.4 Displaying Bridging Functions
  • 3.5 Enabling Trunking
    • Trunk Groups
  • 3.6 Disabling Trunking
  • 3.7 Displaying Trunking Status
  • 3.8 Enabling Port monitoring
  • 3.9 Disabling Monitoring
  • 3.10 Displaying monitoring Status
  • 3.11 Defining and Deleting Workgroups
  • 3.12 Assigning a Community Name
  • 3.13 Configuring Broadcast/Multicast Storm 3.13...
  • 3.14 Modifying MIB Variables
  • 3.15 System Contact
  • 3.16 System Name
    • 3.16.1 System Location
    • 3.16.2 Community Names
      • Set Community Name
    • 3.16.3 Aging Parameter
• Monitoring and Managing Your ELS10-26
  • 4.1 ELS10-26 Management Tools
  • 4.2 ELS10-26 Statistics
    • 4.2.1 Gathering Statistics
    • 4.2.2 System Statistics
    • 4.2.3 Ethernet Port Statistics
  • 4.3 Using LCM to Check ELS10-26 Status
    • 4.3.1 Displaying Status
    • 4.3.2 Displaying MAC Addresses
    • 4.3.3 Displaying Manufacturing Information
  • 4.4 Managing the ELS10-26
  • 4.5 Using LCM to Manage the ELS10-26
    • 4.5.1 Disabling a Port
    • 4.5.2 Enabling a Port
      • noRIP Option
    • 4.5.3 Changing a Subnet Mask
    • 4.5.4 Changing a Community Name
    • 4.5.5 Setting the Baud Rate
    • 4.5.6 Setting a Reboot Time
• ELS10-26 Diagnostics and Troubleshooting
  • 5.1 Power-up Diagnostics
    • 5.1.1 Power-up LED Sequence
    • 5.1.2 Specific Power-up Tests
    • 5.1.3 Software Checksum Comparison
    • 5.1.4 Power-up Diagnostics Results
  • 5.2 Responses to Failures at Power-up
  • 5.3 Status and Activity Indicators
  • 5.4 Troubleshooting
  • 5.5 ELS10-26 Does Not Power Up
    • 5.5.1 Connectivity Problems
    • 5.5.2 ELS10-26 Has Rebooted
    • 5.5.3 ELS10-26 Does Not Respond to NMS
• Technical Specifications
  • A.1 ELS10-26 Specifications
    • Physical
    • Electrical
    • Connector Ports
    • Environmental
    • Diagnostic LEDs
    • Standard Support
    • Address Table Size
    • Management Support
    • Regulatory Compliance
  • A.2 Serial Cable Pin Assignments
  • A.3 10BASE-T Pin Assignments
  • A.4 Straight-through Wiring
  • A.5 Crossover Wiring
  • A.6 5 - 4 - 3 Rule
  • A.7 FEPIM Specifications
    • FE-100TX
    • FE-100FX
• Glossary
• Index