Cal Comp Electronics BC8160 Bluetooth Headset User Manual BC8100 manual

Cal-Comp Electronics (Thailand) Co. Ltd. Bluetooth Headset BC8100 manual

UserMan

Quick GuideAppearance1. LED Indicator (Blue)2. Power on/off button3. Volume down button4. Volume up button5. Multi-function button (MFB)6. Microphone location7. Speaker location8. Bendable ear-hook9. USB charging portCharging"For optimizing battery performance, the headset must be charged for at least 12 hours for the first time."Subsequent full charge requires around 2.5 hours. (Five short tones warning every 20 seconds mean that the battery level is low and immediate charging is required.)How to Charge3.Power source for charging is from travel charger adapter (optional) or standard mini USB cable connected to computer/ notebook USB port.1.Plug in charger/ USB cable into the charging port. During charging, blue indicator will light up.2.When fully charged blue indicator light goes off.Switching On/Off the Headset<On>Press and hold power switch for more than 4 seconds. Blue indicator light will flash rapidly 4 times and at the same time an audio tone can be heard through the speaker, indicating headset been switch on. <Off>Press and hold power switch for more than 4 seconds. Blue indicator light will flash rapidly 2 times and at the same time an audio tone can be heard through the speaker, indicating headsets been switched off.Pairing the Headset to Your Phone 1.Make sure the headset is off.2.Press and hold on the power switch button for approximately 8 seconds until the LED indicator is always on (no flashing). 3.Turn on your phone's Bluetooth function and search for device. 4.Select the device "I-MOBILE BHS-304" device listed on the phone screen.from the found 5.Enter "0000" as the password and select OK. When your headset is successfully paired, the indicator light changes to rapid blue flashes and at the same time an audio tone can be heard through the speaker.6.If the phone fails to connect to the headset automatically after being paired, tab the MFB once, and the headset will try to connect to phone. Your phone may ask you to confirm the connection with the headset, please select "Yes". Retry if failed.7.The pairing mode will last 120 seconds, before going into standby mode. If pairing fails or timeout, repeat all over again from step 1.Making & Answering CallsActionHS ProfileTab the MFBTab the MFBFunctionDevice StatusPhone Headset HF ProfileMaking a voice dial call Standby StandbyStandbyStandbyStandby StandbyTab the MFB None None None None NoneRedial last call Long press theMFBLong press theMFBLong press theMFB NoneLong press theMFBReceive a call RingingRingingReject a callEnd a call Conn-ectedConn-ectedConn-ectedConn-ectedToggle between two active callsConn-ected &On holdConn-ected &RingingAnswer a second incoming callLED IndicationActionHS ProfileFunctionDevice StatusPhone Headset HF ProfileStandby : not on call, Ringing : in coming callConnected: on a call, On hold : 1 call been placed on hold Tab the MFB NoneConn-ectedConn-ected &On holdEnd a currentcallHeadset status4 rapid flashes10 rapid flashes1 Fast flash per 3 seconds1 Slow flash per 8 seconds Power offActionPower On 2 rapid flashesCharging & Pairing mode Always on (no flashing)Pairing succeededStandby modeConnectedBattery fully charged Indicator light turn offAudio TonesHeadset status The audio tonePower onPower offSingle ToneSingle ToneSingle high tonePairing success 1 single high tone1 single high toneIncome call Melody toneLong press the MFBBattery lowConnect successConnect failed5 rapid high tones per 20 secondsNo network service 2 rapid high tones per 20 secondsMicrophone mutedReached Max./Min. Volumes1 low tone per 5 seconds2 tones from low to high 2 tones from high to low Notice1.It is normal that the battery life will gradually deteriorate, from repeated charging of the headset. 2.The headset will be switch off during charging for safety reasons. 15.105 Federal Communications Commission (FCC) Requirements, Part 15This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.2.This device may not cause harmful interference.1.This device must accept any interference received, including interference that may cause undesired operation.Declaration of Conformity harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause Consult the dealer or an experienced radio/TV technician for help.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Increase the separation between the equipment andreceiver.Reorient or relocate the receiving antenna.This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Regulatory information / DisclaimersInstallation and use of this Bluetooth headset device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by manufacturer may void the user's authority to operate the equipment. Manufacturer is not responsible for any radio or television Interferencecaused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correctany interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. This product complies with the following standards: EN 300 328 EN 301 489-1/-17 EN 60950
RF exposure warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu