CalAmp Wireless Networks 14071R2 Wireless broadband router User Manual gsm

CALAMP WIRELESS NETWORKS INC. Wireless broadband router gsm

Contents

user manual gsm

AERCEPTDATARADIOLANDCELLOMEGASMARTLINK299JohnsonAvenue,Suite110|Waseca,MN56093|t507.833.8819|f507.833.6748|calamp.com Dataradio VVaanngguuaarrdd 33GGTM (GSM Version) Rugged Cellular Radio Modem User Manual P/N 001-7001-100 Version 1 April 2009 Preliminary
TABLE OF CONTENTS 001-7001-100 Version 1 Page 2 of 65 Vanguard 3G User Manual GSM Version 1.PREFACE......................................................................................................................................................................41.1COPYRIGHTNOTICE................................................................................................................................................................41.2MODEMUSE.........................................................................................................................................................................41.3INTERFERENCEISSUES.............................................................................................................................................................41.4MOBILEAPPLICATIONSAFETY...................................................................................................................................................52.PRODUCTOVERVIEW...................................................................................................................................................62.1DEVICEIDENTIFICATION...........................................................................................................................................................62.2GENERALDESCRIPTION............................................................................................................................................................62.3FEATURES.............................................................................................................................................................................62.4PARTNUMBERBREAKDOWN....................................................................................................................................................72.5EXTERNALINTERFACES............................................................................................................................................................82.6RJ‐45ETHERNETPORTINTEGRATIONPARAMETERS....................................................................................................................102.7POWERCABLECONNECTIONS.................................................................................................................................................102.8ANTENNAOPTIONS..............................................................................................................................................................123.NETWORKINGBASICS................................................................................................................................................153.1GENERALNETWORKINGDEFINITIONS.......................................................................................................................................154.GETTINGSTARTED.....................................................................................................................................................174.1PACKAGECONTENTS.............................................................................................................................................................174.2SETUPREQUIREMENTS..........................................................................................................................................................174.3QUICKSTART.......................................................................................................................................................................174.4CONFIGURINGLOCALPC.......................................................................................................................................................184.5VANGUARD3GRADIOMODEMSETUP....................................................................................................................................194.6PROVISIONINGTHEVANGUARD3GRADIOMODEM...................................................................................................................215.VANGUARD3GCONFIGURATION...............................................................................................................................235.1GENERALINSTRUCTIONS........................................................................................................................................................235.2HOMEPAGEPARAMETERS.....................................................................................................................................................235.3CELLULARWANPARAMETERS...............................................................................................................................................265.4LANSETTINGS.....................................................................................................................................................................295.5WIFI(WLAN)....................................................................................................................................................................325.6ROUTERSETTINGS................................................................................................................................................................395.7ADVANCEDSETTINGS............................................................................................................................................................405.8SNMP...............................................................................................................................................................................495.9GPSSTATUSANDSETTINGS...................................................................................................................................................495.10SERIALPORTSETTINGS........................................................................................................................................................535.11I/OSETTINGS....................................................................................................................................................................545.12SYSTEMUPGRADE(OPTIONALSERVICE).................................................................................................................................596.TROUBLESHOOTING...................................................................................................................................................607.SPECIFICATIONS.........................................................................................................................................................628.ABBREVIATIONS.........................................................................................................................................................649.SERVICEANDSUPPORT..............................................................................................................................................659.1PRODUCTWARRANTY,RMAANDCONTACTINFORMATION...........................................................................................659.2RMAREQUEST.................................................................................................................................................................659.3PRODUCTDOCUMENTATION..........................................................................................................................................659.4TECHNICALSUPPORT.......................................................................................................................................................65 Preliminary
TABLE OF CONTENTS 001-7001-100 Version 1 Page 3 of 65 Vanguard 3G User Manual GSM Version FIGURE1‐DATARADIOVANGUARD3GRADIOMODEM’SFRONTPANEL.....................................................................................................8FIGURE2‐DATARADIOVANGUARD3GRADIOMODEM’SBACKPANEL.......................................................................................................9FIGURE3‐DATARADIOVANGUARD3GPOWERCABLECONNECTIONS......................................................................................................10FIGURE4‐DATARADIOVANGUARD3GPOWERCABLECONNECTIONS......................................................................................................11FIGURE5‐ALTERNATIVEDATARADIOVANGUARD3GPOWERCABLECONNECTIONSWITHIGNITIONSENSEDELAYTIMER...................................11FIGURE6‐ANTENNASPACING..........................................................................................................................................................13FIGURE7‐VANGUARD3GRADIOMODEMSETUPEQUIPMENT................................................................................................................17FIGURE8‐LOCALAREACONNECTIONPROPERTIES(WINDOWSXP).........................................................................................................18FIGURE9‐INTERNETPROTOCOL(TCP/IPPROPERTIES).........................................................................................................................19FIGURE10‐VANGUARD3GRADIOMODEMHOMEPAGE.......................................................................................................................20FIGURE11‐VANGUARD3GPRODUCTCELLULAR(WAN)PAGEDIALSETTINGS..........................................................................................21FIGURE12‐VANGUARD3GPRODUCTCELLULAR(WAN)PAGEACTIVATION.............................................................................................22FIGURE13‐VANGUARD3GRADIOMODEMHOMEPAGE.....................................................................................................................24FIGURE14‐VANGUARD3GRADIOMODEMCELLULAR(WAN)STATUSPAGE..........................................................................................27FIGURE16‐LANSETTINGSPAGE......................................................................................................................................................29FIGURE17‐MACPAIRING..............................................................................................................................................................32FIGURE18‐VANGUARD3GWIFIMODES:ACCESSPOINT(A);CLIENTMODE(B).....................................................................................32FIGURE19‐WIFI(WLAN)ÆSTATUS...............................................................................................................................................33FIGURE20‐WIFI(WLAN)ÆWIRELESSSETTINGS(CLIENT)..................................................................................................................34FIGURE21‐WIFI(WLAN)ÆWIRELESSSETTINGS(ACCESSPOINT)........................................................................................................36FIGURE22‐WIFI(WLAN)ÆWIRELESSSETTINGS(STATISTICS)............................................................................................................38FIGURE23‐WIFI(WLAN)ÆWIRELESSSETTINGS(SITESURVEY)..........................................................................................................38FIGURE24‐STATICROUTESSCREEN..................................................................................................................................................39FIGURE25‐ROUTINGTABLE............................................................................................................................................................40FIGURE26‐PORTFORWARDINGSCREEN............................................................................................................................................41FIGURE27‐THIRDPARTYDEVICEREMOTEACCESSEXAMPLE.................................................................................................................42FIGURE28‐DYNAMICDNS(NO‐IPCONFIGURATION)SETUPSCREEN.....................................................................................................43FIGURE29‐IPFILTER.....................................................................................................................................................................47FIGURE30‐REMOTEADMIN............................................................................................................................................................48FIGURE31‐IPADDRESSDEFINITIONS................................................................................................................................................49FIGURE32‐POWERMANAGEMENT..................................................................................................................................................49FIGURE33‐GPSSTATUS................................................................................................................................................................50FIGURE34‐GPSLOCALDELIVERY.....................................................................................................................................................51FIGURE35‐I/OSETTINGS‐STATUS....................................................................................................................................................56FIGURE36‐I/OSETTINGS...............................................................................................................................................................57FIGURE37‐I/OSETTINGS‐LABELS....................................................................................................................................................58 TABLE1‐LEDDEFINITIONS...............................................................................................................................................................8TABLE2‐STANDARDRJ‐45ETHERNETPIN‐OUT..................................................................................................................................10TABLE3‐POWERSUPPLYCONNECTIONS.............................................................................................................................................11TABLE4‐ENCRYPTIONKEYSEXAMPLES..............................................................................................................................................35TABLE5‐I/OSIGNALPINOUT..........................................................................................................................................................54TABLE6‐I/OSIGNALSPECIFICATIONS................................................................................................................................................55Preliminary
PREFACE 001-7001-100 Version 1 Page 4 of 65 Vanguard 3G User Manual GSM Version 1. PREFACE 1.1 Copyright Notice ©2009 CalAmp Corp. All Rights Reserved. This manual covers the operation of the CalAmp Dataradio Vanguard 3G CDMA Cellular Modem. Specifications described are typical only and are subject to normal manufacturing and service tolerances. CalAmp reserves the right to modify the equipment, its specifications or this manual without prior notice, in the interest of improving performance, reliability, or servicing. At the time of publication all data is correct for the operation of the equipment at the voltage and/or temperature referred to. Performance data indicates typical values related to the particular product. No part of this documentation or information supplied may be divulged to any third party without the express written consent of CalAmp Corp. Products offered may contain software which is proprietary to CalAmp Corp. The offer or supply of these products and services does not include or infer any transfer of ownership. 1.2 Modem Use The Dataradio Vanguard 3G cellular modem is designed and intended for use in fixed, nomadic, or mobile applications. “Fixed” assumes the device is physically secured at one location and not easily moved to another location. “Mobile” assumes the modem is physically secured in a vehicle and is operated when the vehicle is moving. “Nomadic” assumes the modem is installed in a vehicle but is operated when the vehicle is stationary. Please keep the cellular antenna of the Vanguard 3G radio modem at a safe distance from your head and body while the modem is in use (see below). Caution: Maintain a distance of at least 20 cm (8 inches) between the transmitter antennas and any person while in use. This modem is designed for use in applications that observe the 20 cm separation distance. 1.3 Interference Issues Avoid possible radio frequency (RF) interference by following these guidelines: • The use of cellular telephones or devices in aircraft is illegal. Use in aircraft may endanger operation and disrupt the cellular network. Failure to observe this restriction may result in suspension or denial of cellular services to the offender, legal action or both. • Do not operate in the vicinity of gasoline or diesel-fuel pumps unless use has been approved and authorized. • Do not operate in locations where medical equipment that the device could interfere with may be in use. • Do not operate in fuel depots, chemical plants, or blasting areas unless use has been approved and authorized. • Use care if operating in the vicinity of protected personal medical devices, i.e., hearing aids and pacemakers. Preliminary
PREFACE 001-7001-100 Version 1 Page 5 of 65 Vanguard 3G User Manual GSM Version • Operation in the presence of other electronic equipment may cause interference if equipment is incorrectly protected. Follow recommendations for installation from equipment manufacturers. 1.4 Mobile Application Safety • Do not change parameters or perform other maintenance of the Vanguard 3G modem while driving. • Road safety is crucial. Observe National Regulations for cellular telephones and devices in vehicles. • Avoid potential interference with vehicle electronics by correctly installing the Dataradio Vanguard 3G radio modem. CalAmp Corp recommends installation by a professional. FCC Notification: This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 6 of 65 Vanguard 3G User Manual GSM Version 2. PRODUCT OVERVIEW 2.1 Device Identification 2.1.1 Label Information The label contains the CalAmp part number, serial number, MAC ID, FCC ID and the IMEI numbers in both Hex and decimal format. 2.2 General Description The Dataradio Vanguard 3G Modem from CalAmp Corp is the ideal solution for a wide range of Internet Access, Corporate Network and wireless IP connectivity requirements. The Vanguard 3G product features high-speed wireless wide-area-network access to IP networks over 3G cellular networks. The Vanguard 3G cellular radio modem advanced router features full Ethernet routing, DHCP Server, and NAT support. The embedded GPS makes it an ideal fit for mobile applications requiring position information and Internet connectivity. The optional built-in 802.11 WiFi tether allows you to step away from your vehicle and remain connected at all time. Alternatively, the client mode forwards all traffic via the WiFi interface instead of the cellular interface. 2.3 Features  HSDPA Tri-band 850/1900/2100 MHz with data transfer rates up to 3.6 Mbps downlink, 384 kbps uplink  OR HSUPA Quad-band 850/900/1800/1900 MHz with data transfer rates up to 7.2 Mbps downlink, 2.0 Mbps uplink  OR GPRS Quad-band 850/900/1800/1900 MHz with data transfer rates up to 236 Kbps downlink, 236 kbps uplink  Embedded Linux (with support for custom applications) on ARM 9 processor  Built-in DHCP server and NAT support  Browser-based management  Embedded GPS  Local and remote configuration  10/100 Ethernet interface  WiFi IEEE 802.11b/g 2.4GHz (optional)  Built-in WiFi client and access point (AD HOC mode)  PPPoE and RIP  RSSI indicator  I/O capability  MAC pairing  SIM card lock/unlock feature  SIM card slot Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 7 of 65 Vanguard 3G User Manual GSM Version 2.4 Part Number Breakdown 140-71CC-LST 140-71 = Vanguard 3G model identifier 140-71CC-LST CC = 00-99 Carrier/Technology/Cell Module Number 00 = None 01 = Verizon Wireless - CDMA - MC5727 02 = AT&T – GSM - MC8790 03 = Sprint - CDMA - MC5727 04 = T-mobile - GSM - MC8790 05 = Bell Mobility - CDMA - MC5727 06 = Rogers Communication - GSM - MC8790 07 = Telstra (Australia) - GSM - MC8775 08 = Alltel - CDMA - MC5727 09 = Telus - CDMA - MC5727 L = LAN Communication Options 0 = Wired LAN 1 = WiFi + Wired LAN S = Sensor Options 0 = GPS 1 = GPS & I/Os T = TBD options Reserved for future Options (0=Standard) Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 8 of 65 Vanguard 3G User Manual GSM Version 2.5 External Interfaces 2.5.1 Front Panel Connections Figure 1 - Dataradio Vanguard 3G radio modem’s Front Panel Vanguard 3G radio modem front panel connections include: GPS: SMA female, GPS antenna connector. This input requires a 3.3V, GPS antenna with an SMA connection. For best coverage, use an active GPS antenna with a gain of >25dBm. PWR: 9-28 VDC; the mating connector is a Molex 43025-0400 4 position connector. LAN: Input for standard or crossover Ethernet cable. USB: Connection for USB Client port. USB is not supported at this time. COM: Standard RS-232 port for debugging and maintenance only. ANT: TNC female, primary antenna connection. See section 2.8 “Antenna options” for more information. RX DIV1: SMA female, receive diversity antenna. See section 2.8 “Antenna options” for more information. WiFi: RP-SMA jack, WiFi antenna. See section 2.8 “Antenna options” for more information. 2.5.2 LEDs There are five LEDs on the front panel of the Vanguard 3G unit. Each can display three colors: Red, Green, and Amber. The definition for each LED is as follows: Table 1 - LED Definitions LED OFF GREEN FLASHING GREEN RED FLASHING RED AMBER WiFi No Power Or Interface Disabled Interface Enabled TX/RX Activity N/A N/A N/A PWR (Power) No Power Power on N/A N/A Power Timer Activated Power Up, Ignition Sense OFF STAT (Status) No Power Status OK N/A N/A N/A Medium or Low RSSI NET (Network Connectivity) No Power Network Connected TX/RX Activity No Coverage N/A N/A GPS No Power Position Fix N/A No Satellites Fault Acquiring 1 Diversity Antenna is required for HSUPA Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 9 of 65 Vanguard 3G User Manual GSM Version Acquired in View Detected Satellites, no fix yet 2.5.3 Back Panel Connections Vanguard 3G radio modem back panel connections include: Reset: Hard reset button2 I/O: I/O interface connector SIM Card: A slot to insert your SIM card 2.5.3.1 To install your SIM card: 1. Remove Protective cover 2. Using a pencil point, press the yellow eject button and remove the SIM card holder (see Figure 2) 3. Insert your SIM card into the holder. Make sure the gold contacts of the card face up. 4. Slide the SIM card holder back into the socket. Caution: Make sure to slide the holder into the allocated slot. Be careful not to sink the card inside the unit. 5. Replace the protective cover. Figure 2 - Dataradio Vanguard 3G radio modem’s Back Panel 2 Hard reset does not default parameter configuration Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 10 of 65 Vanguard 3G User Manual GSM Version 2.6 RJ-45 Ethernet Port Integration Parameters Table 2 below provides the information to purchase Ethernet cables to integrate the Vanguard 3G product into your system. Note: The Vanguard 3G radio modem can accept either a standard or cross over Ethernet cable. Table 2 - Standard RJ-45 Ethernet Pin-out Pin Function Color 1 TX + White/Orange 2 TX - Orange/White 3 RX + White/Green 4 Blue/White 5 White/Blue 6 RX - Green/White 7 White/Brown 8 Brown/White 2.7 Power Cable Connections If using the provided power cable to connect to a DC supply (car battery) use the following diagrams and table to connect the unit. Note: Both ignition sense and DC power are required to start up a Vanguard 3G unit. Figure 3 - Dataradio Vanguard 3G Power Cable Connections Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 11 of 65 Vanguard 3G User Manual GSM Version Table 3 - Power supply connections Pin Color Description 1 Red DC Power, 9 to 28V DC 2 Blue Ground 3 White Ignition Sense 4 NA No Connect Figure 4 - Dataradio Vanguard 3G Power Cable Connections Ignition Sense Delay TimerRedBlueWhite-GND+OutIn Figure 5 -Alternative Dataradio Vanguard 3G Power Cable Connections with Ignition Sense Delay Timer If connection to an AC supply is desired, an AC/12VDC power supply and cable are available. Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 12 of 65 Vanguard 3G User Manual GSM Version 2.8 Antenna Options Antennas are available for Vanguard 3G radio modems installations from CalAmp Corp. 2.8.1 Primary Cellular Antenna The Vanguard 3G product requires a multi-band cellular antenna for operation in the 800 MHz band, the 1900 MHz band, and the 2100 MHz band. The primary antenna connection on the Vanguard 3G unit is a TNC female connector; therefore you must purchase an antenna with a TNC male connector. Do not select a TNC antenna with “reverse polarity” or RP-Male. Mounting options and cable lengths are the user’s choice and application specific. Caution: To comply with FCC approval for this device, do not use a cellular antenna with a gain greater than 5 dBi in the cellular (800MHz) band, or 4 dBi in the 1900MHz band. 2.8.2 RX Diversity Cellular Antenna3 The Vanguard 3G radio modem RX Diversity antenna has the same requirements as the primary antenna with the exception of the connection. The RX Diversity antenna connection on the Vanguard 3G product is an SMA female connector; therefore an antenna with an SMA Male connection is required. Mounting options and cable lengths are the user’s choice and application specific. For best performance, separation between the Primary and Diversity antenna should be at least 5/8 wavelength (=8 inches or 20 cm for 915 MHz). Caution: To comply with FCC approval for this device, do not use a cellular antenna with a gain greater than 5 dBi in the cellular (800MHz) band, or 4 dBi in the 1900MHz band. 2.8.3 GPS Antenna The Vanguard 3G radio modem’s GPS connector requires an external 3.3V GPS antenna. The GPS antenna connection on the Vanguard 3G product is a female SMA connector; therefore an antenna with an SMA male connector is required. For best coverage, use an active antenna with a gain >25dB. Mounting options and cable lengths are user’s choice and application specific. 2.8.4 WiFi Antenna The WiFi antenna connection on the Vanguard 3G product is an RP-SMA jack; therefore an antenna with an RP-SMA plug is required. Mounting options and cable lengths are user’s choice and application specific. Industry Canada RSS Notices: This device has been designed to operate with the antennas listed below, and having a maximum gain of 5.5 dBi. Antennas not included in this list or having a gain greater than 5.5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Manufacturer Model Number Antenna Type Gain RadioLabs Inc 2.4-mobile3 Mag Mount 5.5 dBi 3 Diversity Antenna is optional for HSDPA Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 13 of 65 Vanguard 3G User Manual GSM Version WR≥23.6"(60cm)G≥8"(20cm)≥8"(20cm) ≥5/8λ 915 ΜHz: 8" (20cm) TTo reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. 2.8.5 Antenna Spacing Referring to Figure 6 for illustration, Vanguard 3G radiomodem commonly uses four separate antennas: • “T” - Main transceiver - Constraints are the limit of 20 cm and omni-directional factors • “R” - Auxiliary receiver – Constraints are the receiver spacing of at least 5/8 λ (wavelength) from transceiver antenna and omni-directional requirements • “G” - Global Positioning System (GPS) Constraints are TX spacing of at least 60cm/23.62 inch from all transmitting antennas and a clear view of the sky. • “W” – WiFi antenna Constraints are TX spacing of at least 8 inches or 20 cm from all transmitting antennas Note: For units utilizing diversity cellular antennas, best overall operation is achieved utilizing antennas with equal gains WARNING: As per FCC rules, all Vanguard 3G transmitting antennas should be at a minimum of eight (8) inches (approximately 20 centimeters) from all persons. T- Primary Antenna R-Diversity Antenna G-GPS Antenna W-WiFi Antenna Figure 6 - Antenna Spacing4 4 The diagram is not drawn to scale Preliminary
PRODUCT OVERVIEW 001-7001-100 Version 1 Page 14 of 65 Vanguard 3G User Manual GSM Version For installation of ground-plane dependent antennas (main cellular and WiFi antennas), the center of the metal surface used for mounting is preferable for best omni-directional pattern. For ground-plane independent antennas (diversity and GPS antennas), installation may be close to the edges of the surface. For vehicular installations CalAmp recommends the following antenna positions: • Most preferred for all antennas: centerline of roof. For transmitter antenna, it is the ONLY acceptable position. • Less preferred for receiver antenna: trunk lid, providing distance to transmitting antenna is respected whether lid is opened or closed. • Much less preferred, but permissible for receiver antenna: left or right rear fenders, just in back of rear window • Least preferred, but permissible for receiver antenna: left or right front fenders, ahead of windshield Preliminary
NETWORKING BASICS 001-7001-100 Version 1 Page 15 of 65 Vanguard 3G User Manual GSM Version 3. Networking basics 3.1 General Networking Definitions The Vanguard 3G cellular modem is based on Ethernet connectivity and follows general IP networking guidelines and terminology. Below are definitions of some basic network terminology as they pertain to the Vanguard 3G environment. Term Definition Circuit Switched Data Circuit Switched Data is the original form of a cellular connection where a radio channel is dedicated to an active phone and the connection is dropped when not in use. DNS Domain Name System: operates like a phone book to translate domain names (i.e., google.com) to IP addresses (70.212.19.1). The Vanguard 3G unit functions as the DNS Server in the network. DHCP Dynamic Host Configuration Protocol: the DHCP server assigns IP addresses, gateway and subnet masks to all clients on the network. The Vanguard 3G unit functions as a DHCP Server. Dynamic/Static IP A device with Dynamic IP selected may have a different IP address every time it connects to the network. A device with a Static IP will always connect with the same IP address. Gateway A (node) device enabling data transfer between different networks (i.e., from a private LAN to a public WAN). LAN Local Area Network. A private network. NAT Network Address Translation: A technology that allows hosts on the LAN with private IP addresses to communicate with public IP addresses on the WAN. This is an essential function of a network router. Packet Data Packet Data is used by 3G cellular standards. On a packet data network, users share a channel and the connection is always on. Port A special number present in the header of a data packet in the data transfer process. Ports are typically used to map data to a particular process running on a computer. PPP Point-to-point Protocol: creating a direct link between two nodes in network communication. Private IP address Private IP addresses are addresses that will not be routed on external networks. Any device on an internal LAN should be assigned a private IP address to avoid contention. The suggested private address ranges are Class A: 10.x.x.x Class B: 172.16.x.x through 172.31.x.x Class C: 192.168.x.x By default the Vanguard 3G radio modem uses the 192.168.1.x address range. Provisioning The process of activating a unit for the first time on a cellular carrier’s network. You must have a service contract in place with the carrier prior to provisioning your device. RIP Routing Information Protocol, protocol that helps routers dynamically adapt to changes of network connections by communicating information about which networks each router can reach and how far away those networks are. SSID Service Set Identifier. This is a name used to identify a WiFi wireless network. Subnet A range of addresses assigned to a LAN. All devices connected in a Vanguard 3G network must be on the same subnet as the Vanguard 3G radio modems. Subnet Mask Binary string that separates the subnet portion of an IP address and the host portion. Preliminary
NETWORKING BASICS 001-7001-100 Version 1 Page 16 of 65 Vanguard 3G User Manual GSM Version TKIP/AES “Temporal Key Integrity Protocol” is an encryption method used by the WiFi interface when operating in WPA mode. TKIP was designed to solve security issues in WEP (it is considered stronger then WEP). "Advanced Encryption Standard" is the encryption protocol used by the WiFi interface when it operates in WPA2 mode. WAN Wide Area Network, a public network. The Internet is an example of a WAN. WEP Wired Equivalent Privacy. This is an IEEE security protocol for wireless 802.11 networks. It is an encryption method used by the WiFi interface. WiFi (802.11b, 802.11g) Wireless Fidelity is an IEEE 802.11 standard for wireless LANs Æ802.11b is a standard for operating at 2.4 GHz frequency with data rates up to 11 Mbps Æ802.11g is a standard for operating at 2.4 GHz frequency with data rates up to 54 Mbps WiFi Access Point (802.11 Ad-Hoc mode) A Vanguard 3G unit can operate in 802.11 Ad-Hoc mode. It can communicate with other devices operating in 802.11 Ad-Hoc mode. Although it is not a true WiFi access point, we call it one because it serves as the gateway to the WAN for the other wireless devices operating in Ad-Hoc mode. WiFi Client (802.11 Infrastructure mode) A Vanguard 3G unit can operate in 802.11 Infrastructure mode. In this mode it is a WiFi client and will try to connect to a WiFi access point. WLAN Wireless Local Area Network, a private network. Refers to the network covered by the WiFi interface. WPA/WPA2 WiFi Protected Access" is a subset of 802.11i (security mechanisms for wireless networks). "WiFi Protected Access 2" is the complete version of 802.11i. Preliminary
GETTING STARTED 001-7001-100 Version 1 Page 17 of 65 Vanguard 3G User Manual GSM Version 4. GETTING STARTED 4.1 Package Contents  Vanguard 3G cellular modem  Quick Start Guide  Power cable and Fuse  User Manual and Quick Start Guide on CD  Mounting Bracket and Screws 4.2 Setup Requirements  Vanguard 3G cellular modem  Computer running any operating system  9 to 28 Volt power supply  Ethernet cable*  Active cellular data account  Cellular antenna with male TNC connector*  Cellular Diversity Antenna (SMA Male) *  GPS Antenna (SMA Male) *  WiFi Antenna (RP-SMA Plug) * ( if applicable) *These accessories are available from CalAmp. 4.3 Quick Start 4.3.1 Hardware Setup Figure 7 - Vanguard 3G radio modem setup equipment 1. Connect the primary cellular antenna to the ANT connector on the front of the unit. For units utilizing diversity, install RX Diversity antenna on SMA connector. Connect the GPS antenna to the GPS connector. For units utilizing WiFi, connect the WiFi antenna to the WiFi connector. 2. Connect an Ethernet cable from the LAN connector of the Vanguard 3G unit to the PC. If multiple PCs are being used, connect the Vanguard 3G unit to an Ethernet switch or hub connected to the PCs. 3. Connect a power supply cable to the PWR connector of the Vanguard 3G unit. Do not power the unit on yet. Preliminary
GETTING STARTED 001-7001-100 Version 1 Page 18 of 65 Vanguard 3G User Manual GSM Version 4.4 Configuring Local PC 1. Verify network settings on local PC are set to automatically detect IP and DNS server. The path to network settings varies with the version of Windows you are using. Windows XP: Start-> Control Panel -> Network Connections Windows 2000: Start -> Settings -> Network and dial up connections 2. Select the appropriate network connection, typically the Local Area Connection -> right click on the connection and select “Properties” 3. Select “Internet Protocol (TCP/IP) properties. Figure 8 - Local Area Connection Properties (Windows XP) 4. Verify that “Obtain an IP address automatically” and “Obtain DNS Server address automatically” are selected. Preliminary
GETTING STARTED 001-7001-100 Version 1 Page 19 of 65 Vanguard 3G User Manual GSM Version Figure 9 - Internet Protocol (TCP/IP Properties) 4.5 Vanguard 3G Radio Modem Setup 1. Power on the Vanguard 3G radio modem with 9-28VDC 15-Watt supply. 2. In an Internet browser, enter http://192.168.1.50. This will bring up the Vanguard 3G product login page (Note: It may take 30 seconds from initial power-up for the homepage to be available.) 3. Login to the device Default Login values User logon: admin password: password 4. This brings up the Vanguard 3G product homepage. You can view status and configuration parameters from this screen. The configuration options are further explained later in this document. Preliminary
GETTING STARTED 001-7001-100 Version 1 Page 20 of 65 Vanguard 3G User Manual GSM Version Figure 10 - Vanguard 3G radio modem Homepage Preliminary
GETTING STARTED 001-7001-100 Version 1 Page 21 of 65 Vanguard 3G User Manual GSM Version 4.6 Provisioning the Vanguard 3G Radio Modem IMPORTANT NOTE: The Vanguard 3G cellular radio modem requires an active cellular data service contract and a SIM card for provisioning. Verify that your cellular service contract is a data service contract with packet data NOT circuit switched technology. If you do not have an active data contract or a SIM card, contact your service provider. Note: The Vanguard 3G radio modems are carrier specific. You must activate your unit with the carrier specified when the product was ordered. The unit must be activated in the carrier’s home area. The carrier should provide you with the following items: a) A SIM card b) Carrier APN c) User Name d) Password 4.6.1 Provisioning the Vanguard 3G Radio Modem 1. Install the SIM card provided by your service provider into the SIM slot as described in section 2.5.3.1. 2. On the left side of the screen, select the Cellular (WAN) page. Select “Dial Settings” tab. 3. Select “Enable” under Dial Configuration, and then select your GSM Band (USA or Europe). Refer to Figure 11. 4. Enter Carrier APN, User Name, and Password (provided by your carrier). Click Save. Refer to Figure 11. Note: Dial Number is set to *99# by default. Confirm with your carrier if a different entry is required. Figure 11 - Vanguard 3G product Cellular (WAN) page Dial Settings Preliminary
GETTING STARTED 001-7001-100 Version 1 Page 22 of 65 Vanguard 3G User Manual GSM Version 5. Select “Activation Tab” (Figure 12). Check status under “SIM operation”. If “No_operation_required” is displayed, proceed to next step. If “Enter_CHV1” is displayed, a PIN code is required for operation. Enter your PIN code in the designated space and click “Save”. Figure 12 - Vanguard 3G product Cellular (WAN) page Activation 6. Once the unit is activated, browse to an Internet web page to confirm connectivity. Note: Should you experience problems connecting to the web page, reset the Vanguard 3G unit by clicking RESET on the top right of the screen and try reconnecting to the web page. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 23 of 65 Vanguard 3G User Manual GSM Version 5. Vanguard 3G Configuration This section explains status information and configuration options available on all HTML pages. 5.1 General Instructions The following instructions are common to all HTML pages The Help, Home and Reset links are located at the top right of all HTML pages. Help: Select this link on any of the devices configuration pages to bring up the help text for that screen. Home: Select this link to return to the home page of the modem. Reset: Select this link to command the unit to reboot. This process will take about 40 seconds. The software will ask you to confirm this command prior to re-booting. Save: Most changes to a configuration parameter require the user to click save before the change will take effect. Clear/Cancel: Most configuration menus also have a “Clear/Cancel” option. Selecting this button will restore all fields in a section to their last saved value. Note: This does not return them to their factory defaults. 5.2 Home Page Parameters The Vanguard 3G cellular modem home page lists the unit’s primary operating parameters and status. Configuration changes cannot be made from this page. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 24 of 65 Vanguard 3G User Manual GSM Version Figure 13 - Vanguard 3G Radio Modem Home Page Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 25 of 65 Vanguard 3G User Manual GSM Version 5.2.1 Home Page Parameter Descriptions System Information Unit ID: Unit identification number (configured under Basic Settings). System Up Time: System Up Time displays a counter that starts when the unit is powered on and resets when the unit is powered down or hardware reset. Note: This counter does NOT indicate how long the WAN connection has been up. Software Version: This reflects the version of application software loaded on the unit. Phone Module Version: This is the version of the cellular module installed in the device. This may be required by tech support but is not required for any user applications. Serial Number: This is assigned at the factory. This may be required by tech support but is not required for any user applications. Default Route: Network route used by the Vanguard 3G cellular radio modem when no other known route exists for a given IP packet's destination address. The default route points to the Cellular interface when WAN is up. The only exception to this rule is if the WiFi interface is configured in wireless client mode and is connected to a WiFi access point (WiFi Status=Up). In that case, the default route will point to the WiFi interface. Note: When the connection to the WiFi access point is down the default route is set back to the Cellular interface. Ethernet (LAN) IP Address: IP Lists the LAN IP address of the Vanguard 3G unit. This IP becomes the gateway and DNS server for all PCs and devices connected on the LAN. This value is configured on the LAN Settings Page. Subnet Mask: The Subnet mask is used in conjunction with the network address to partition the IP address into the network (subnet) portion and the host portion. In most cases, this value will be automatically set by the software based on the class of IP address used for the Ethernet IP. This value can be modified on the LAN Settings page. MAC Address: Media Access Control Address, this is configured at the factory and cannot be changed by the user. WiFi (WLAN) Status: Indicates if the WiFi interface is “UP” or “DOWN” IP Address: IP address assigned to the WiFi interface of this device. When the WiFi interface is set to operate in WiFi Client mode, the WiFi Access Point must have a DHCP server running to assign an IP address to its WiFi clients. Subnet Mask: Subnet Mask assigned to the WiFi interface of this device. MAC Address: Media Access Control Address of the WiFi interface. Cellular (WAN) Status: indicates if the device has an established connection to the WAN. Status is UP or DOWN IP Address: WAN IP address of the Vanguard 3G unit. Remote access for the device requires entering this address into a browser. The PPP IP Address is assigned by the cellular carrier and will be dynamic unless a static address is specifically requested Warning: Be aware of the dynamic nature of the WAN IP Address as it can affect related applications. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 26 of 65 Vanguard 3G User Manual GSM Version Subnet Mask: This subnet mask is assigned by the carrier and is not configurable by the user. P-t-P: WAN IP address of the network access point of the cellular carrier GSM Connection Service Type: Service Type indicates the type of service connection. Service Mode: UMTS/HSDPA, UMTS/HSPA, or EDGE/GPRS Carrier: Registered Carrier Roaming Status: Roaming Status indicates the unit roaming status. Status is ROAMING or NOT ROAMING. Signal Strength: Receive Signal Strength Indication indicates the strength of the network signal with both a numerical value and a good/medium/poor message. Connection Status: Indicates if the device has an established connection with a carrier. 5.3 Cellular WAN Parameters This page contains the provisioning information and the carrier activation settings. For more information on the procedure for carrier activation, see section 4.6 “Provisioning the Vanguard 3G Radio Modem”. 5.3.1 Status WAN Status information is available (Figure 14). Service Type: Service Type indicates the type of service connection. Service Mode: UMTS/HSDPA, UMTS/HSUPA, or EDGE/GPRS IMEI: International Mobile Equipment Identity MIN/MSI: Mobile Identification Number; in most cases, this is the same as MDN Country: Country where the unit is located Carrier: Registered Carrier Band: North America (850/1900 MHz), Europe (900/1800 MHZ), or Australia (850/2100 MHz) Cell ID: Status only. Assigned by carrier when connecting to the network Roaming Status: Roaming Status indicates the unit roaming status. Status is ROAMING or NOT ROAMING. Signal Strength: Receive Signal Strength Indication indicates the strength of the network signal with both a numerical value and a good/medium/poor message. Connection Status: Indicates if the device has an established connection with a carrier. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 27 of 65 Vanguard 3G User Manual GSM Version Figure 14 - Vanguard 3G Radio Modem Cellular (WAN) Status Page 5.3.2 Activation SIM configuration parameters (refer to Figure 12) To change PIN Code: 1. Enter your old code under “Old Pin Code” 2. Enter your new code under “Pin code (CHV1) 3. Click Save Pin unblock code: The code required to unlock a GSM SIM card that was disabled after an incorrect PIN code was entered three times in a row. To unlock it use the PUK code (Personal Unblocking Key) which was provided by your carrier upon purchasing the SIM card. If you have lost the PUK code, you may contact your carrier in order to retrieve it. Note that service provides impose a limit on how many times in a row you can enter an incorrect PUK code before the SIM card becomes invalid (cannot be unlocked). Check with your carrier for additional information. SIM unlock code (MEP): The code required to unlock the modem for a given region (band). You must contact the carrier (service provider) to obtain the network MEP code. SIM operation: SIM operation Status. 5.3.3 Dial Settings Refer to section 4.6. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 28 of 65 Vanguard 3G User Manual GSM Version Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 29 of 65 Vanguard 3G User Manual GSM Version 5.4 LAN Settings Figure 15 - LAN Settings Page The LAN Settings page contains the basic configuration information required to customize your LAN with the Vanguard 3G radio modem as the network connection point. User configuration will primarily occur on this page. PPPoE settings can be found under “Advanced” tab (see section 5.4.2). 5.4.1 IP Settings 5.4.1.1 IP Configuration Ethernet IP address: LAN IP of the VANGUARD 3G radio modem. This address is entered into a browser on a local PC when logging into the Vanguard 3G radio modem home page. To decrease the chances of unwanted access, this value should be changed from its default prior to use. IMPORTAT NOTE: Changing this value will cause you to lose connection to the Vanguard 3G unit. Enter the new address in the browser to reconnect. If you forget an address or make a mistake entering the new value, it may be difficult to reconnect to the device. Ethernet Subnet Mask: The Subnet mask is used in conjunction with the Ethernet IP address to partition the address into the network (subnet) portion and the host portion. This value will be entered automatically by the software based on the class of IP address entered. It is not be necessary to change the default value once the Ethernet IP is entered. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 30 of 65 Vanguard 3G User Manual GSM Version 5.4.1.2 DNS Masquerade See the definition for DNS in Network Basics in section 3.1 above. DNS Auto: The command enables/disables the Vanguard 3G DNS server. Except in special cases, this should always be enabled. One exception to this is if using a PPPoE connection. 5.4.1.3 DHCP Server Configuration DHCP Server: (Dynamic Host Configuration Protocol) A protocol used by client devices that are connected to the LAN port of this device to automatically obtain an IP address assigned by this server/router. Selecting Enable will configure this device to assign IP addresses to client devices taken from a pool specified by the values entered in DHCP start range and DHCP end range. If DHCP is disabled, the information must be entered manually on all PCs. DHCP Start IP Address/End IP Address: Sets the range of IP addresses assigned to the PCs. The user can limit the number of devices allowed on the network by limiting the range of IP addresses. IMPORTANT NOTE: The addresses in this range must be on the same subnet as the Ethernet IP IMPORTANT NOTE: The Ethernet IP should not be in the DHCP range. DHCP Lease Time: Number that dictates the length of time a device on the LAN can hold an IP address. In most cases, this should be set to the maximum (default value) of 86400. If this value is set too low, it can cause network connectivity problems. Domain Name Suffix: The DNS suffix to be assigned by the DHCP server. Preferred DNS Server: IP address of the preferred DNS server. Alternate DNS Server: IP address of the alternate DNS server. 5.4.1.4 Disabling DHCP server When DHCP server is enabled, any PC with physical access to the Vanguard 3G Ethernet port will be assigned an IP address and have access to browse the Internet. This may cause security problems. Disabling DHCP server will allow the user to control which PCs have the ability to connect through the Vanguard 3G radio modem. If changes are made to the network settings, be sure to keep a record of the changes for future use.  Disabling DHCP server is performed on the LAN settings page. Under the DHCP section, select Disable, then click Save. IMPORTANT NOTE: This also disables DNS Masquerading. Disabling DHCP server will remove all values in the DHCP and DNS sections. Record all values in these fields prior to disabling in case you are required to go back to the original configuration.  To improve security, change the Ethernet IP of the Vanguard 3G unit from the default setting. IMPORTANT NOTE: If the DHCP server is disabled, and you do not have a record of the Ethernet IP, you will not be able to login to the Vanguard 3G home page. On the network setting page of each PC set the following Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 31 of 65 Vanguard 3G User Manual GSM Version – IP address: Set a unique address on the same subnet as the Vanguard 3G radio modem – Subnet Mask: Set to the same value as the CiPHRs Ethernet Subnet Mask field – Default Gateway: Ethernet IP of the Vanguard 3G radio modem – Preferred DNS: Ethernet IP of Vanguard 3G radio modem When these settings are complete, the PC will have network access. 5.4.1.5 Static IP Setup If your network requires each PC to have a statically set LAN IP addresses, follow the previous procedure for all PCs on the network. If the network requires a mix of static and dynamically assigned IP addresses, assign static IPs outside the DHCP address range for PCs that require static IP addresses and allow the Vanguard 3G radio modem DHCP to assign the remaining PC IP addresses. 5.4.2 Advanced (PPPoE Setup) PPPoE Setup: PPP over Ethernet; PPPoE is used to create a password protected broadband connection. To use this feature, configure a broadband network connection on your PC. The procedure for setting up the broadband connection differs for different versions of Windows. When enabled, the DHCP Server is automatically disabled and configuration is erased Note: In most cases, PPPoE is not required and the DHCP server should be left enabled. 5.4.3 MAC Pairing For enhanced security, the user can pair a Host PC to the Vanguard 3G unit by specifying the Host’s Ethernet MAC address. This ensures that only this particular host PC can send and receive traffic to and from the WAN interface of the Vanguard 3G unit. Connections that do not have the matching source MAC address will be blocked. Note: Access to the Vanguard 3G unit itself is always available regardless of the Ethernet MAC address and will not be blocked. Status: Vanguard 3G is unpaired: No host PC is paired with the Vanguard 3G unit. Any host PC on the LAN can send and receive traffic to and from the WAN interface Vanguard 3G is paired: A host PC is paired with the Vanguard 3G unit. Only the paired host PC can pass data to and from the WAN interface. Current Address: The current Ethernet MAC address of the paired host PC. Note: to change the paired host PC, the user must specify the current Ethernet MAC address of the last paired host PC. E.G. 00:12:34:56:78:AB New Address: Ethernet MAC address of the host PC to be paired with the Vanguard 3G unit. Confirm New Address: Confirm the new Ethernet MAC address of the host PC to be paired with the Vanguard 3G unit. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 32 of 65 Vanguard 3G User Manual GSM Version Figure 16 - MAC Pairing 5.5 WiFi (WLAN) A Vanguard 3G unit can operate in an access point mode (Ad-Hoc) and in a client mode. In access point mode, the Vanguard 3G radio modem offers wireless tether. It forwards local WiFi traffic to application servers over the cellular network and works in parallel with Ethernet connection, providing for simultaneous WiFi and Ethernet connections (see Figure 17A). In client mode the Vanguard 3G unit can automatically switch between cellular and WiFi connections providing for seamless handover when coupled with modern applications (see Figure 17B). Figure 17 - Vanguard 3G WiFi Modes: Access Point (A); Client Mode (B) Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 33 of 65 Vanguard 3G User Manual GSM Version 5.5.1 WiFi (WLAN)ÆMain WiFi settings provide user configuration for optimal WiFi interface operation. Figure 18 - WiFi (WLAN) ÆStatus Configuration Wireless Mode: Disable: The WiFi interface is disabled Client: The WiFi interface operates in Client mode Access Point: The WiFi interface operates in Access Point mode (Ad-Hoc) Status IP Address: IP address assigned to the WiFi interface Subnet Mask: IP Subnet Mask assigned to the WiFi interface SSID: Name of the wireless local area network Authentication: Authentication method currently used (Example: Open, Shared, WPANONE, WPA-PSK, WPA2-PSK) Encryption: Encryption method currently used Channel: Channel currently used (Auto or 1-11) State: Current state of the WiFi interface (Disabled, Ready if in Access point Mode, or Not Connected, Scanning, and Connected if in Client Mode) RSSI: Received Signal Strength Indicator (displayed in Client Mode only) Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 34 of 65 Vanguard 3G User Manual GSM Version 5.5.2 WiFi (WLAN)ÆWireless Settings (Client) The user can configure up to 20 access points. Note: All access points must run a DHCP server. In wireless client mode, the Vanguard 3G unit will try to connect to the Access Point with the strongest signal on the list. When the Vanguard 3G unit connects to an access point, it starts a DHCP client service. The DHCP server running on the access point must provide an IP address, netmask, and gateway to the Vanguard 3G unit. When the WiFi client is connected to a WiFi access point, the default route is set to point to the gateway address obtained by the DHCP client. Figure 19 - WiFi (WLAN)ÆWireless Settings (Client) Wireless Settings Access Point Number: Access point number SSID: Service Set Identifier. This is the name of the wireless local area network. Channel: Channel number to use (Auto or 1-11) Authentication: Authentication method to be used (Example: Open, Shared, WPANONE, WPA-PSK, WPA2-PSK) Encryption: None, WEP, TKIP, or AES WEP Key Length: the bit key length WEP Key Type: type of WEP security WEP Key Index: 1-4 Key: The encryption key Note: For a 64-bit key, keys are 5 character strings long if WEP Key Type is set to ASCII and 10 hexadecimal digits long if WEP Key Type is set to HEX. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 35 of 65 Vanguard 3G User Manual GSM Version For a 128-bit key, keys are 13 character strings long if WEP Key Type is set to ASCII and 26 hexadecimal digits long if WEP Key Type is set to HEX. The following table shows examples of encryption keys depending on encryption type chosen. Table 4 - Encryption Keys Examples Encryption Type Description Key (Example) WEP Encryption 64-bit/ASCII 5 character string CrYpT 64-bit/Hexadecimal 10 hexadecimal digits mYEncryptKeY4 128-bit/ASCII 13 character string LongHello1234 128-bit/Hexadecimal 26 hexadecimal digits 12345678901234567890ABCDEF TKIP Encryption Any Key A string of 8 to 63 characters AbCdEfGhIjKlMnOp AES Encryption Any Key A string of 8 to 63 characters AbCdEfGhIjKlMnOp Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 36 of 65 Vanguard 3G User Manual GSM Version 5.5.3 WiFi (WLAN)ÆWireless Settings (Access Point) Figure 20 - WiFi (WLAN)Æ Wireless Settings (Access Point) IP Settings IP Address: IP address of the WiFi interface Subnet Mask: The network mask of the WiFi interface DNS Masquerade DNS Auto: Enables or disables the Vanguard 3G DNS server on the WiFi interface Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 37 of 65 Vanguard 3G User Manual GSM Version DHCP Server DHCP Server: Enables or disables DHCP server on the WiFi interface Start IP Address: Starting IP address (defines the pool of addresses allocated for DHCP purpose) End IP Address: Ending IP address (defines the pool of addresses allocated for DHCP purpose) Lease Time: The period over which the IP address allocated to a DHCP client is referred to as a “lease”. Lease duration is the amount entered in seconds. Domain Name Suffix: DNS suffix to be assigned by the DHCP server Preferred DNS Suffix: IP address of the preferred DNS server Alternate DNS Suffix: IP address of the alternate DNS server Wireless Settings SSID: Service Set Identifier. This is the name of the wireless local area network. Channel: Channel number to use (Auto or 1-11) Authentication: Authentication method to be used (Example: Open, Shared, WPANONE, WPA-PSK, WPA2-PSK) Encryption: Encryption method currently used WEP Key Length: the bit key length WEP Key Type: type of WEP security WEP Key Index: 1-4 Key: The encryption key Note: For a 64-bit key, keys are 5 character strings long if WEP Key Type is set to ASCII and 10 hexadecimal digits long if WEP Key Type is set to HEX. For a 128-bit key, keys are 13 character strings long if WEP Key Type is set to ASCII and 26 hexadecimal digits long if WEP Key Type is set to HEX. Refer to Table 4 for examples of encryption keys depending on encryption type chosen. 5.5.4 WiFi (WLAN)ÆWireless Settings (Advanced) Not supported in the current version. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 38 of 65 Vanguard 3G User Manual GSM Version 5.5.5 WiFi (WLAN)ÆStatistics Figure 21 - WiFi (WLAN)Æ Wireless Settings (Statistics) Transmit TX Packets: Number of packets sent by the Vanguard 3G unit over the WiFi interface TX Bytes: Number of bytes sent by the Vanguard 3G unit over the WiFi interface Receive RX Packets: Number of packets received by the Vanguard 3G unit over the WiFi interface RX Bytes: Number of bytes received by the Vanguard 3G unit over the WiFi interface 5.5.6 WiFi (WLAN)ÆSite Survey Figure 22 - WiFi (WLAN)Æ Wireless Settings (Site Survey) When the WiFi interface of the Vanguard 3G unit operates in Client mode, this screen shows the WiFi Access Point detected during last wireless scan. The list is empty when the Vanguard 3G unit is operating in Access Point mode. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 39 of 65 Vanguard 3G User Manual GSM Version 5.6 Router Settings Router settings provide advanced user configuration for large network setups. 5.6.1 RIP Settings Not supported in the current version 5.6.2 Static Routes Figure 23 - Static Routes Screen The Vanguard 3G unit will automatically set up routing to all devices on the same subnet. In some cases however, the Vanguard 3G unit may need to communicate with a previously existing subnet other than its own. This route cannot be automatically generated; it must be manually entered as a static route by the user. The static route gives the Vanguard 3G radio modem its “next hop” instructions. Route no: A generic number assigned to the route. Multiple static routes can be assigned as long as they have distinct route numbers. Route Name: Nickname assigned to the route by the user. Destination IP Address: This is the destination IP address that is delivered to the Vanguard 3G radio modem. Since this IP address will not be on the same subnet, the Vanguard 3G radio modem will not have a defined route, and will not know where to send it by default. Setting up the static route will inform the Vanguard 3G radio modem where to send the data. IP Subnet Mask: The Subnet mask is determined by the subnet of the destination address Gateway IP: This is the address that the data packet will be routed to. Note: The device at this address must be a router that is either on the same subnet as the Destination IP or one with its own statically setup route to the destination address. If this is not the case, the packet data will be dropped. Metric: This sets the priority of the routes compared to other static routed defined. The lower the number, the higher priority the route. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 40 of 65 Vanguard 3G User Manual GSM Version Click on “Add” when all necessary information has been entered. The route will be shown on the bottom of the screen (under Static Routing Table). Additional routes can be added provided they have a unique Route no, name and metric. Routes can be deleted by clicking the Delete Entry option of the desired entry. Note: Routing table (found under “Table” tab) shows all routes, while Static Table (found under “Settings” tab) shows manually entered routes only. 5.6.3 Routing Table The table in Figure 24 shows a list of all routes (static and dynamic). Figure 24 - Routing Table 5.7 Advanced Settings 5.7.1 Advanced Settings -NAT and Port Forwarding (Mapping) When NAT is enabled, the LAN (Ethernet) is considered private, the WAN is considered public. Any IP packets leaving the Vanguard 3G unit through the WAN interface will have its source IP address changed to that of the WAN interface. Any data transfer must be initiated from the private side of the network toward the public side. Port Forwarding is used to provide remote access to third party devices on the LAN, such as Web Cameras or printers. Port Forwarding routes incoming requests from the WAN, with a specific port to a local device with a static IP. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 41 of 65 Vanguard 3G User Manual GSM Version Figure 25 - Port Forwarding Screen NAT: Network Address Translation (NAT) on the WAN interface of the Vanguard 3G unit. When NAT is enabled, the LAN (Ethernet) is considered private, the WAN is considered public. Any IP packets leaving the Vanguard 3G unit through the WAN interface will have its source IP address changed to that of the WAN interface. Port Forwarding: Enable - The Vanguard 3G unit performs port forwarding. The "IP Mapping Table" contains the rules used to perform port forwarding. Disable - The Vanguard 3G unit does not perform port forwarding on the WAN interface. Mapping Number: User selected generic number assigned for this route. Protocol: TCP, UDP, or both - driven by the protocol used by the third party device Source IP Address: Enter the IP address of the remote PC connecting to the third party device. (This should only be done if a single PC with a STATIC IP is accessing the device and you want to limit access to the device.) If you will be accessing the third party device from multiple PCs, or from a PC that has a dynamically assigned WAN IP, enter 0.0.0.0 (wildcard) to allow all remote PCs to access the third party device. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 42 of 65 Vanguard 3G User Manual GSM Version Incoming Port: Enter the port of incoming request. This can be any non-conflicting port (can be the same as the destination port). This value must be entered following the Vanguard 3G IP address into a browser on a remote PC to access the third party device. Destination IP Address: IP address of third party device; must be on the same subnet as the Vanguard 3G radio modem. Destination Port: Enter the port of the third party device. This will be assigned to the device by the third party manufacturer and should be in the user manual of the third party device IMPORTANT NOTE: The password protection on the Vanguard 3G product does not protect logging into a third party device. The third party device must provide its own password protection (confirm if password protection is required). Click Add when route configuration is complete. The route will be displayed at the bottom of the page. Additional routes may be added but require a unique mapping number and port number. Routes can be deleted (cleared) if no longer needed. Once the route of the third party device is added you can enter the following on a remote PC to access the third party device. Figure 26 - Third Party Device Remote Access Example http://70.209.115.93:81 “PPP IP Address”On home page“Incoming Port”On NAT Configuation MenuNote: “http” must be specified or browser will assume other protocols Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 43 of 65 Vanguard 3G User Manual GSM Version 5.7.2 Advanced Settings-Dynamic DNS (NO-IP Configuration) Dynamic DNS is an option for remote monitoring if a static WAN IP address is not available or not yet assigned. When Dynamic DNS is activated, the Vanguard 3G radio modem will register its dynamically assigned IP address with NO-IP’s application, allowing the user to login to the device remotely without knowing the IP address of the Vanguard 3G radio modem. A number of providers offer services to track dynamic IP addresses and map them to constant domain names. The Vanguard 3G product supports connection with NO-IP.com, one provider of this service. NOTE: As it is more reliable CalAmp recommends the use of a static IP whenever possible. Figure 27 - Dynamic DNS (NO-IP Configuration) Setup Screen NO-IP: Enable/Disable (disabled by default) User at NO-IP.com: User name setup at NO-IP.com. This information is required when logging into your account. NOIP Password: Password used when logging into your account at NO-IP. Hostname: This is unique domain name setup on your NO-IP account. This is the domain name entered into a browser to remotely login to the Vanguard 3G radio modem. You may have multiple host names registered on the same account. See section below for instructions to set up NO IP account and host name. IMPORTANT NOTE: Do not assign more than one Vanguard 3G unit the same domain name. Update Interval: This setting determines how often the device will update its IP information at NO-IP. The IP addresses assigned by the carrier are dynamic; therefore it is necessary to update the registered IP periodically. Setting a high value in this field may cause extended periods of no connection but will reduce the number of times the Vanguard 3G registers, decreasing the amount data used on the contract. Setting a low value minimizes the chance of lost network connection but will increase the total amount of data used on the contract. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 44 of 65 Vanguard 3G User Manual GSM Version The Vanguard 3G radio modem will always register when first powered up or upon hardware reset. 5.7.2.1 Instruction for NO IP setup 1. Setup an account at NO-IP.com http://www.no-ip.com/. You will need to setup a user name and password on your account 2. On No-IP, create a host account for each device you want to remotely monitor. The domain name you set up here will be used to remotely login to the device. 3. On the Vanguard 3G radio modem, click “Dynamic DNS” on the left side of the web Browser. 4. Enable NO-IP 5. Enter your NO-IP username, password and hostname for this device (do not assign the same host name to multiple devices.) 6. Set the update interval (30 minutes is the default). 7. After registration is complete, you can login into the unit or use the port forwarding feature by entering the hostname into a web browser followed by the port number. (Example http://Vanguard_user.no-ip.biz:8080) 5.7.3 Advanced Settings- IP Filter IP Filtering provides certain Internet firewall protection. The user can enter up to 20 IP filters. Each IP filter is identified by a unique number (from 1 to 20). When IP filtering is enabled, any custom IP filters entered by the user as well as predefined IP filters will be taken into account when processing IP packets. See Figure 28. An IP packet passes through the filtering logic when IP filtering is enabled: 1) An IP packet is received on one of the interface and is destined to the Vanguard 3G unit OR 2) An IP packet is sent by the Vanguard 3G unit OR 3) An IP packet is forwarded by the Vanguard 3G unit. 5.7.3.1 Predefined IP Filters Block Remote Pings: If IP filtering is enabled, any ICMP echo request coming from the WAN interface will not be replied to. This prevents remote hosts from detecting your IP address on the WAN. Block Remote IP Fragments: If IP filtering is enabled, any fragmented IP packets coming from the WAN interface will be dropped. 5.7.3.2 Add Custom IP Filters Fill in the parameters described below and click “Add…”. Your entry should appear in the Custom IP Filters table on the bottom of the page. Note: Criteria are for inclusion by default. Select “exclude” if you criterion is for exclusion. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 45 of 65 Vanguard 3G User Manual GSM Version Filter Number: Each IP filter is identified by a unique number from 1 to 20. Source IP Address: Any Any source IP Address will satisfy these criteria. Specific A specific Host IP address. Range A range of IP addresses. Destination IP Address: Any Any destination IP Address will satisfy these criteria. Specific A specific Host IP address. Range A range of IP addresses. Protocol: Any Any protocol number. ICMP The ICMP protocol (1). TCP The TCP protocol (6). UDP The UDP protocol (17). Other Any other IP protocol. Source Port: Any Any source port number. Specific A specific source port number Range A range of source port numbers Destination Port: Any Any destination port number. Specific A specific destination port number Range A range of destination port numbers Direction: The direction corresponds to the path taken by the IP packet inside the Vanguard 3G unit. An IP packet can TERMINATE inside the Vanguard 3G unit. wan2ciphr The IP packet is received from the WAN interface and is destined to the Vanguard 3G unit. eth2ciphr The IP packet is received from the Ethernet interface and is destined to the Vanguard 3G unit. wifi2ciphr The IP packet is received from the WiFi interface and is destined to the Vanguard 3G unit. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 46 of 65 Vanguard 3G User Manual GSM Version An IP packet can ORIGINATE from the Vanguard 3G unit. ciphr2wan The IP packet is sent by the Vanguard 3G unit to the WAN interface. ciphr2eth The IP packet is sent by the Vanguard 3G unit to the Ethernet interface. ciphr2wifi The IP packet is sent by the Vanguard 3G unit to the WiFi interface. An IP packet can be FORWARDED by the Vanguard 3G unit wan2eth The IP packet is received on the WAN interface and forwarded to the Ethernet interface. wan2wifi The IP packet is received on the WAN interface and forwarded to the WiFi interface. eth2wan The IP packet is received on the Ethernet interface and forwarded to the WAN interface. eth2wifi The IP packet is received on the Ethernet interface and forwarded to the WiFi interface. wifi2eth The IP packet is received on the WiFi interface and forwarded to the Ethernet interface. wifi2wan The IP packet is received on the WiFi interface and forwarded to the WAN interface. Action: Keep If IP filtering is enabled and an IP packet matches all criteria in the IP filter, keep the IP packet (continue normal processing of the IP packet). Drop If IP filtering is enabled and an IP packet matches all criteria in the IP filter, drop the IP packet. 5.7.3.3 Delete Custom IP Filters Type the filter number (from 1 to 20) in “Filter Number” and click “Delete…”. The entry should be deleted from the Custom IP Filters table. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 47 of 65 Vanguard 3G User Manual GSM Version Figure 28 - IP Filter Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 48 of 65 Vanguard 3G User Manual GSM Version 5.7.4 Advanced Settings-Remote Admin and Power Management Figure 29 - Remote Admin 5.7.4.1 Remote Admin Remote Configure: Selecting Enable will allow remote access to the modem’s configuration screens through the cellular network connection. Selecting Disable will shut off the ability to remotely access the modem’s configuration screens. Incoming Port: Change the port of incoming requests. It is not necessary to change this parameter unless it conflicts with other devices on the network. Admin Password: Set the password for BOTH remote login and local login. The password must be entered twice for the password to change. Note: Changing any remote administration parameters remotely will cause the remote user to lose contact with the Vanguard 3G unit. Login using new parameters to re-establish a connection. IMPORTANT NOTE: Users can be logged into a single unit both locally and remotely at the same time. Changes made on one end will not be reflected on the other unless the web page is refreshed. 5.7.4.1.1 Example of Remote Login The following should be entered into a browser on a remote PC to remote login to the Vanguard 3G radio modem. The Vanguard 3G unit must have remote administration enabled for this functionality to work. http://70.209.115.93:8080 “PPP IP Address” On home page “Incoming Port” On LAN Settings Page Note: “HTTP” must be specified or browser will assume other uses Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 49 of 65 Vanguard 3G User Manual GSM Version Figure 30 - IP Address Definitions 5.7.4.2 Power Management The VANGUARD 3G unit is designed to stay ON even if the ignition is turned OFF. You can configure your Vanguard 3G unit to automatically shut down 1, 5, 30, or 60 minutes after ignition is turned off or when the supply voltage drops to a certain level. Shutdown Method: Disabled by default (unit always ON after ignition is turned OFF). Select “Power Off” to enable power management. After ignition line off: Select between the following time intervals: 1 minute, 5 minutes, 30 minutes, or 60 minutes. When Voltage Drops to: Enter desired voltage. Enter “0” to disable. (Note: A value of 11V would be usually entered here as a precaution in order to ensure the car battery does not drain.) Figure 31 - Power Management 5.8 SNMP Not supported in the current version 5.9 GPS Status and Settings The Vanguard 3G unit incorporates a highly sensitive 16-channel GPS receiver and an intelligent algorithm that offers outstanding receive sensitivity. Summarized below are the specifications of the integrated GPS module: Typical Acquisition sensitivity -138 dBm Typical Tracking sensitivity -147 dBm Reacquisition time Less than 1 second Average Cold/Warm/Hot Start time to first fix Under 45/33/3.5 seconds Position Accuracy 2D CEP 2.5 meters 3D SEP 5 meters DGPS corrected <2 meters Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 50 of 65 Vanguard 3G User Manual GSM Version The GPS page allows the user to see the GPS status and configure remote or local delivery of GPS position reports. Viewing the GPS data from a local or remote PC requires a UDP port listener program be installed on the PC. Any UDP listener will work provided you can set an appropriate port value for the program. 5.9.1 GPS Status Figure 32 - GPS Status Condition: Indicates No Fix, Standard GPS Fix, Differential GPS Fix, or Estimated / Last Known Position Number of Satellites: Indicates the number of satellites the GPS has locked on to. A minimum of 3 is required to establish a position. Generally, the more satellites the GPS has locked, the more accurate the position reporting will be. UTC: Time of day in Universal Coordinated Time Position: Device position reported in degrees and minutes Altitude: Altitude from Mean Sea Level reported in meters. True Course: Heading, reported in degrees (0 – 360) Ground Speed: Reported in km/hr Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 51 of 65 Vanguard 3G User Manual GSM Version 5.9.2 AAVL Settings (Local and Remote Delivery) Figure 33 - GPS Local Delivery TAIP Vehicle ID: User assigned number to identify the vehicle or Vanguard 3G unit that each GPS report belongs to. This will be reported in the GPS messages if TAIP with ID is selected for TCP Server Format and/or UDP Host format. Configured under Basic Settings. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 52 of 65 Vanguard 3G User Manual GSM Version Differential Correction: Differential GPS corrects various inaccuracies in the GPS system to yield measurements accurate to a couple of meters when the mobile is moving and even better when stationary. 5.9.3 Local Delivery The GPS data can be delivered to up to two local PCs with UDP viewer programs can provide data through a TCP connection, e.g. telnet. GPS data will be delivered once per second to all local PCs TCP Server Format: Select one of the following options for the format of the GPS messages TAIP no ID: Trimble ASCII Interface Protocol, a Trimble specified digital communication interface. When this option is selected, the TAIP vehicle ID is not included in the GPS messages. TAIP with ID: Same as above except the Vehicle ID is reported NMEA National Marine Electronics Association interface specification for electronic equipment. The NMEA GPS message set includes several message types, each containing specific GPS information. See message descriptions below. TAIP Vehicle ID is not reported when NMEA is selected. NMEA GLL: Position in LAT/LONG coordinates and time of day in UTC coordinates. NMEA GGA: Position in LAT/LONG coordinates, time of day in UTC coordinates, fix quality, number of satellites and altitude NMEA RMC: Position in LAT/LONG coordinates, time of day in UTC coordinates, ground speed in knots, heading in degrees and date NMEA VTG: Ground speed in kilometers per hour and knots, heading in degrees. To get GPS data by telneting into the device, enter the following from a prompt telnet <local IP address of the Vanguard> 6257. Note: It is possible to telnet to the Vanguard 3G unit’s port 6257 from a remote location however this is not recommended as delivering the data once per second across the cellular network will greatly increase the amount of data transferred on the cellular contract. UDP Host Format: Same options as TCP server format UDP Host Address: IP address of local PC that GPS data will be delivered to. This address must be on the same subnet as the Vanguard 3G LAN IP UDP Host Port: Port assigned to UDP program. This must match the port assigned in the chosen UDP Port Listener Program. Warning: Due to the dynamic nature of the WAN IP address on some cellular networks, remote GPS reports being sent to a Host via UDP may start arriving with a different IP address. In order for the Host to be able to identify the source of the report it is recommended to: a) Use “TAIP, with ID” reports as they contain Vehicle ID field that can be set uniquely for each mobile OR b) Use middleware that maintains a constant IP address across cell towers. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 53 of 65 Vanguard 3G User Manual GSM Version 5.9.4 Remote Delivery The GPS data can be delivered to up to three remote PCs with UDP viewer programs running on the host. Report every: GPS can be programmed to report position after a specified time has elapsed or the unit has moved a specified distance since its last report. But no less than: This feature prevents a fast moving vehicle from reporting too frequently if its “Report every ….. meters” setting is sufficiently low” by setting a minimum amount of time, in seconds, between GPS reports. 5.10 Serial Port Settings Not supported in the current version Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 54 of 65 Vanguard 3G User Manual GSM Version 5.11 I/O Settings The Vanguard 3G modem supports the following I/Os: • Vanguard 3G Input Status: Ignition Sense, Main Voltage indication, and Modem Temperature • Four general purpose external analog input lines (AIN1…AIN4) • Four general purpose external digital input lines (DIN1…DIN4) • Four general purpose external digital outputs (relay-driven contact closures). Implemented as four sets of SPST contacts with leads labeled: NO1-COM1 NO2-COM2 NO3-COM3 NO4-COM4 See Table 5 for pinout. PIN# Description Pin1 AIN4 Pin2 AIN2 Pin3 Analog ground* Pin4 COM4 Pin5 NO4 Pin6 COM2 Pin7 NO2 Pin8 Not used Pin9 Digital ground** Pin10 DIN4 Pin11 DIN2 Pin12 AIN3 Pin13 AIN1 Pin14 Analog ground* Pin15 COM3 Pin16 NO3 Pin17 COM1 Pin18 NO1 Pin19 Not Used Pin20 Digital ground** Pin21 DIN3 Pin22 DIN1 *AIN1 to AIN4 inputs are referred to the Analog ground (pins 3 and 14) **DIN1 to DIN4 are referred to the Digital ground (pins 9 and 20) Table 5 - I/O Signal Pinout Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 55 of 65 Vanguard 3G User Manual GSM Version Table 6 - I/O Signal Specifications 5.11.1 Debouncing All analog and digital input signals are debounced for 500ms. Generation of all alarms and indications is subject to a 500ms debouncing. 5.11.2 I/O Configuration The Vanguard 3G I/O subsystem is configured via the Vanguard 3G WEB pages. Status Monitoring is provided via NMEA-based protocol. The Vanguard 3G I/O subsystem operates according to a manager/agent model. The PC-hosted manager sends requests to the Vanguard 3G I/O agent, which performs the required actions. The Vanguard 3G agent reports alarms and indications to the PC-hosted manager. Input Type Label Specification Analog Input AIN1…AIN4 External input voltage range: 0 to+28 Volts Digital Input DIN1…DIN4 Logical level inputs, Schmitt-trigger Positive threshold voltage: 2.2V max Negative threshold voltage: 0.6V min Maximum input voltage: 5.5V General Purpose External Digital Outputs NO1-COM1 NO2-COM2 NO3-COM3 NO4-COM4 The default Vanguard 3G power-up state for each relay is open (no contact between COM and NO output lines) Nominal Switching Capacity (resistive load) 1A, 30VDC Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 56 of 65 Vanguard 3G User Manual GSM Version Figure 34 - I/O Settings-Status The Manager IP address is configured under I/O SettingsÆNMEA SettingsÆ Manager IP address (see Figure 35). The port number is 1234 by default and can be customized under I/O SettingsÆNMEA SettingsÆ Manager IP addressÆ Port. Note: If Auto is selected for “Manager IP address”, the Vanguard 3G automatically computes the manager IP address to be Vanguard 3G ETH address +1 if DHCP is disabled. If DHCP is enabled, the IP address is the starting address offered by the DHCP server. The unit IP address is the source IP address (displayed in the alarm messages received by the Manager). The user can configure this to be the Cellular (WAN) Vanguard 3G IP address or the LAN (Ethernet) Vanguard 3G IP address. If auto is selected, the source IP address is automatically computed to be Vanguard 3G ETH address +1 if DHCP is disabled. If DHCP is enabled, the IP address is the starting address offered by the DHCP server. For each analog diagnostic value displayed, the user can control alarms conditions in the following ways: • Set acceptable range of values by entering the low and high thresholds. • Choose to be notified when the value goes out of acceptable range and returns into range by enabling each diagnostic value. Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 57 of 65 Vanguard 3G User Manual GSM Version The user can also enable and disable digital alarms by selecting appropriate “enable” and “disable” radio buttons. The alarm messages can be configured for each diagnostic value under I/O SettingsÆLabels (see Figure 36) for both going out of range (OOR) and returning to normal (Normal). Remember to save your settings for each configuration. Figure 35 - I/O Settings Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 58 of 65 Vanguard 3G User Manual GSM Version Figure 36 - I/O Settings-Labels Note: For more information on Vanguard 3G I/O Settings and Configuration refer to TIS082.Preliminary
Vanguard 3G CONFIGURATION 001-7001-100 Version 1 Page 59 of 65 Vanguard 3G User Manual GSM Version 5.12 System Upgrade (Optional Service) It is possible to update the system by receiving an update file from CalAmp Corp. This may be done periodically to add features or fix errata. When you receive an update file, perform the following to update the unit. Upgrading can only be performed from a local PC, not remotely. • Save the file on a local drive or network accessible directory. • On the System Upgrade page, browse to the update file and select it. • Click Save. The system update can take up to 4 minutes. The unit will restart when the upgrade is completed. This will not delete your configuration settings. Preliminary
TROUBLESHOOTING 001-7001-100 Version 1 Page 60 of 65 Vanguard 3G User Manual GSM Version 6. TROUBLESHOOTING This section lists some of the most common problems occurred while setting up the Vanguard 3G unit and troubleshooting tips to fix the problem. Cannot Connect to the Home Page Step 1: Open a DOS command prompt on your PC. (Start - > Programs -> Accessories->Command Prompt_ Enter the command “ipconfig” at the prompt. This will display all IP information assigned to the PC including the IP address, subnet mask and gateway. The Default gateway should be “192.168.1.50” if you are using a new Vanguard 3G unit or should be whatever was assigned as the Ethernet IP of the Vanguard 3G unit during previous configurations. If this is the address, skip to step 2. If the address is other than expected, but is a private IP (see Network basics) and the IP address and gateway are on the same subnet, enter that address in a browser to establish connection. If this does not fix the problem, skip to step 2. If the gateway is not the expected value and does not follow the above format: 1. Close all active browsers 2. On the “Network and Dial-Up Connections Page” confirm that the network settings are set to automatically detect an IP and DNS server. 3. Verify that there are no other active connections; specifically be sure that all wireless cards are disabled. 4. Disable, and then Re-enable the network connection. (Some older versions of Windows do not update network setting automatically, you need to re-enable the network settings or restart the PC to set updated network settings.) 5. Enter “ipconfig” in the command prompt; verify that the Default gateway is now correct. 6. Enter the gateway IP address into a browser, if this does not fix your problem skip to step 2. If the gateway is still not in the correct format, skip to step 3. Step 2: Enter “ipconfig” in the command prompt as instructed above. The IP address should be of the format 192.168.1.xxx if you have new unit or should be on the same subnet if you have changed the Ethernet IP, but should not be the same as the Default gateway. If the address is in the correct format and not the same as the Gateway, skip to step 3. If it is not correct, open the properties window of the network connection. Manually enter a unique IP address on the same subnet as the gateway (use 192.168.1.100 if you have not changed the default) and save the properties. (Note: You may need to disable/re-enable the connection to get the new settings to take effect). This should allow you to connect to the device. Once you are connected, check the DHCP settings; the DHCP server may be disabled. Step 3: Check the following 1. Confirm you are using a working Ethernet cable. Try a different Ethernet cable if necessary. 2. Confirm the Ethernet port you are plugging into on your PC is active. Preliminary
TROUBLESHOOTING 001-7001-100 Version 1 Page 61 of 65 Vanguard 3G User Manual GSM Version 3. Confirm power supply for your unit is functioning. Refer to LED behavior (section 2.5.2). Cannot Connect to the Internet 1. Check the Signal Strength on the home page. If the signal strength is poor, check your antenna connections and placement. Try a different antenna if possible. 2. On the “Dial Settings” page, confirm that the autodial is enabled. If it is disabled, enable it and cycle power. 3. On the “WAN Cellular” page, check that the correct mobile identification number is displayed. If an incorrect number or no number is displayed, it is an indication that your carrier contract is not activated, or the device has not been initiated. If you have not performed an over the air activation (OTASP for Verizon, IOTA for Sprint) perform that now. 4. If you have confirmed all of the above, or the over the air activation fails, contact your network provider to confirm that your contract is active. Internet Connection is Slow or Intermittent Note: The speed and strength of your Internet connection can be affected by many things out of the control of the Vanguard 3G radio modem such as your location and the overall level of network traffic. CalAmp Corp cannot guarantee any speed or coverage. 1. Check the signal strength on the home page. If it is listed as good or medium, skip to the next step. You may want to refresh the home page a few times to make sure the signal strength is consistent. If the signal strength is poor, check you antenna connections or try a new antenna if possible. If this does not fix the problem, verify network coverage in your location with your network provider. Check the Service type. If is listed, skip to the next step. 2. Check the DHCP lease time. If this is set to a high value (>1000 seconds), skip to the next step. If the lease time setting is set to 0 or a low value, reset to a higher value. Unless you have a specific reason for limiting the lease time, this should always be set to the maximum value. 3. If you have completed all steps above and still have poor network performance, perform a speed test on the device to confirm the connection speed (example: speakeasy.net). If the speed test shows acceptable download and upload speeds, the problem is most likely with the specific Internet site you are trying to connect to and not the Vanguard 3G radio modem. Preliminary
SPECIFICATIONS 001-7001-100 Version 1 Page 62 of 65 Vanguard 3G User Manual GSM Version 7. SPECIFICATIONS Product specifications are subject to change without notice. GENERAL SPECIFICATIONS Interface Connectors: RS-232 DE-9S Connector (DCE female) 10/100 Base-T Full Duplex USB Client port5 Power Connector: Molex 43045-4000 MicroFit 3.0, 4 pin header LED Indicators: WiFi, PWR, STAT, NET, GPS Antenna Interface: Primary Antenna: 50-Ohm TNC Female Diversity Antenna: 50-Ohm SMA Female GPS Antenna: 50-Ohm, 3.3V SMA Female WiFi Antenna: 50-Ohm RP-SMA Plug Size: 5.5 (L) x 6.0 (W) x 1.8(H) inches (14 x 15.25 x 4.5 cm) Weight: 2.65lb (1.2 kg) Power Input6: 9-28 VDC Power Consumption: 130mA @ 13.8VDC, cell in RX mode, no WIFI module (average) 240mA @ 13.8VDC, cell in RX mode, with WIFI module 350mA @ 13.8VDC, cell in TX mode, no WIFI module 500mA @ 13.8VDC, cell in TX mode, with WIFI module Max TX Power Range: GSM: 21.5 - 23.5 dBm (includes cable loss 0.5dB) WIFI: 15.5–17.5 dBm (802.11b) & 11.5–13.5 dBm (802.11g) Rx Sensitivity: GSM: <-105 dBm WIFI: <-83 dBm (802.11b) & <-70 dBm (802.11g) Frequencies: Cellular: TX: 824-849 MHz RX: 869-894 MHz PCS: TX: 1850-1910 MHz RX: 1930-1990 MHz WIFI: TX/RX: 2412-2462MHz Temperature: Operating: -30°C to +70°C 100% duty cycle Note: Cellular TX power may be reduced outside this range Storage: -40° to +85°C (-40° to 185°F) Vibration: MIL-STD-810F Method 514.4 Shock: MIL-STD-810F, Method 516.5 Emissions: FCC Part 15b Transport Protocol : UDP/TCP 5 Reserved for future use 6 Power consumption while transmitting is dependent on the TX power level of the cellular module. The TX power level of the module is controlled by the cellular base station, not the Vanguard 3G software Preliminary
SPECIFICATIONS 001-7001-100 Version 1 Page 63 of 65 Vanguard 3G User Manual GSM Version Command Protocol: Web Interface Certifications: FCC ID: EOT14071R2 IC: 773A-14071R2 EU RoHS, CE Preliminary
ABBREVIATIONS 001-7001-100 Version 1 Page 64 of 65 Vanguard 3G User Manual GSM Version 8. ABBREVIATIONS Abbreviation Description CDMA Code Division Multiple Access Vanguard Cellular Industrial Packet Handler Radio CTS Clear to Send DHCP Dynamic Host Configuration Protocol DNS Domain name Server ESN Electronic Serial Number EVDO Evolution Data Optimized GPRS General Packet Radio Service GPS Global Positioning System HSDPA High Speed Downlink Packet Access IOTA Internet Over the Air IP Internet Protocol LAN Local Area Network LED Light Emitting Diode NAT Network Address Translation OTA Over the Air OTASP Over the Air Service Provisioning PAD Packet Assembly/Disassembler PPP Protocol Point to Point PRL Preferred Roaming List SIM Subscriber Identification Module RIP Routing Information Protocol RSSI Receive Signal Strength Indication RTS Request to Send WAN Wide Area Network UART Universal Asynchronous Receiver-Transmitter USB Universal Serial Bus Preliminary
SERVICE AND SUPPORT 001-7001-100 Version 1 Page 65 of 65 Vanguard 3G User Manual GSM Version 9. SERVICE AND SUPPORT 9.1 PRODUCT WARRANTY, RMA AND CONTACT INFORMATION CalAmp Corp guarantees that every Dataradio Vanguard 3G Cellular Modem will be free from physical defects in material and workmanship for one (1) year from the date of purchase when used within the limits set forth in the Specifications section of this manual. Extended warranty plans are available. If the product proves defective during the warranty period, contact CalAmp Customer Service to obtain a Return Material Authorization (RMA). 9.2 RMA REQUEST Contact Customer Service: CalAmp – Dataradio 299 Johnson Avenue, Suite 110 Waseca, MN 59093-USA phone: (1) 507.833.8819 fax: (1) 507.833.6748 BE SURE TO HAVE THE EQUIPMENT MODEL AND SERIAL NUMBER, AND BILLING AND SHIPPING ADDRESSES ON HAND WHEN CALLING. When returning a product, mark the RMA clearly on the outside of the package. Include a complete description of the problem and the name and telephone number of a contact person. RETURN REQUESTS WILL NOT BE PROCESSED WITHOUT THIS INFORMATION. For units in warranty, customers are responsible for shipping charges to CalAmp Corp. For units returned out of warranty, customers are responsible for all shipping charges. Return shipping instructions are the responsibility of the customer. 9.3 PRODUCT DOCUMENTATION CalAmp Corp reserves the right to update its products, software, or documentation without obligation to notify any individual or entity. Product updates may result in differences between the information provided in this manual and the product shipped. For the most current product documentation, visit www.calamp.com for spec sheets. 9.4 TECHNICAL SUPPORT Technical support hours: Monday to Friday 9:00 AM to 5:00 PM, Eastern Time CalAmp – Dataradio Corp 6160 Peachtree Dunwoody RD., suite C-200 Atlanta, Georgia 30328 phone: (1) 770.392.0002 fax: (1) 770.392.9199 Email address: PSMGsupport@calamp.com Preliminary

Navigation menu