CalAmp Wireless Networks BDD4T85-1 Paragon/PD User Manual 392039

Download:
Mirror Download [FCC.gov]
Document ID	392039
Application ID	9lXzuo0E3XT0JNP8lNfoFw==
Document Description	IVIS option technical appendix
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	8.86kB (110783 bits)
Date Submitted	2004-01-27 00:00:00
Date Available	2004-03-01 00:00:00
Creation Date	2004-01-27 16:10:06
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-01-27 16:10:06
Document Title	Microsoft Word - 392039
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

Preliminary version
ParagonPD+ Deviation adjust for optional Integra VIS controller/switch (IVIS)
The ParagonPD+ optional Integra VIS (IVIS) deviation must be adjusted to match its associated
base station.
Referring to Section 4.1, obtain and setup “Required Equipment” listed. Following initial
matching, deviation testing is an annual check.
The setup port of the IVIS controller module is used to connect the PC running the system
software supplied along with the module. The procedure outlined below may ONLY be carried
out to calibrate the IVIS module. If the Exciter needs re-tuning or for annual maintenance check
or troubleshooting, the procedures outlined in Section 4 MUST be followed.
1. From the operating network settings, record the speed (19.2 or 9.6 kb/s) and the channel type
(25 or 12.5 kHz). Using the software’s “Production Test window”, select “Tx Deviation Adj”
radio button in “Adjustments frame” and set “Tx Mode” to Tone.
2. Press F5 (Tx On Tx frequency) to start the transmission.
3. Using PageUp/Dn or Ctrl+PageUp/Dn., adjust the “Tx Deviation Adj” value until the
deviation reading on IFR matches or is slightly less than the value in the “Tone” column of
the table below. Record the reading of the “Direct Adjust” field from the “Adjustments”
frame (initial value)
Speed and Channel
Tx Mode
“Tone”
Tx Mode
“Random Data”
19200b/s 25kHz
±4.0 kHz
±4.5 kHz
9600b/s 25kHz
±4.0 kHz
±4.8 kHz
9600b/s 12.5 kHz
±2.5 kHz
±3.0 kHz
4. Press F5 to toggle the transmission OFF.
5. Change the “Tx mode” to Random Data.
6. Press F5 to toggle transmission of “Random data” ON. Measure the deviation and check that
it is equal to or less than the value in the table. Press F5 to toggle the transmission OFF.
7. If the measurement at step 6 is excessive, repeat steps 2-6 once to obtain deviation readings
that best correspond to the table values. If unable to obtain a “Direct Adjust” reading (after
editing up and/or down) that varies from the initial value (from step 3 above) by less than 2,
contact System Engineering.
8. When satisfied with value obtained, press “Write” button on the button bar to write the value
in the unit’s flash memory.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2004:01:27 16:10:06-05:00
Modify Date                     : 2004:01:27 16:10:06-05:00
Page Count                      : 1
Creation Date                   : 2004:01:27 21:10:06Z
Mod Date                        : 2004:01:27 21:10:06Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : Administrator
Metadata Date                   : 2004:01:27 21:10:06Z
Creator                         : Administrator
Title                           : Microsoft Word - 392039

EXIF Metadata provided by EXIF.tools