Cambium Networks X2120 Wireless Access Point User Manual
Xirrus, Inc. Wireless Access Point
Contents
- 1. User Manual
- 2. Users Manual
User Manual
August 28, 2015
X2 and XR300 Series Notices
Notices and Regulatory Guide
is a registered trademark of Xirrus, Inc. All other trademarks and brand names are marks of their
respective holders.
All rights reserved. This document may not be reproduced or disclosed in whole or in part by any means without
the written consent of Xirrus, Inc.
Part Number: 812-0142-001 Rev D August 28, 2015
X2 and XR300 Series Notices and Regulatory Guide
1
X2 and XR300 Series Notices
This document contains the following information:
“Notices” on page 1
“EU Directive 1999/5/EC Compliance Information” on page 5
“Safety Warnings” on page 9
“Translated Safety Warnings” on page 10
“Software License and Product Warranty Agreement” on page 11
“Hardware Warranty Agreement” on page 15
Notices
Wi-Fi Alliance Certification
www.wi-fi.org
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate RF energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following safety measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced wireless technician for help.
This document contains Notices, Warnings, Compliance and Legal information for the X2 and XR300
Series only. This includes the XR320 (marketed as XR-320) and the X2120 (marketed as X2-120).
For Notices, Warnings, and Compliance information for other indoor products, please see Appendices in the
Xirrus Wireless Access Point User’s Guide. For Notices, Warnings, and Compliance information for
outdoor products, please see the Quick Installation Guide for that product.
!FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
X2 and XR300 Series Notices and Regulatory Guide
2
This device complies with Part 15 of the FCC Rules, with operation subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
For X2 Series products available in the USA/Canada market, only channels 1~11 can be operated. Selection of
other channels is not possible.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
This device is restricted for indoor use. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To ensure
compliance with FCC and Industry Canada RF exposure requirements, this device must be installed in a location
where the antennas of the device will have a minimum distance of at least 30 cm (12 inches) from all persons,
except that X2 models must have a minimum distance of at least 20 cm (8 inches) from all persons. Using higher
gain antennas and types of antennas not certified for use with this product is not allowed.
Non-Modification Statement
Unauthorized changes or modifications to the device are not permitted. Use only the supplied internal antenna, or
external antennas supplied by the manufacturer and approved for this device. Non-approved antennas may
produce unwanted spurious or excessive RF transmitting power which may be prohibited and violate regulatory
limits. Modifications to the device will void the warranty and may violate FCC regulations.
Cable Runs for Power over Ethernet (PoE)
If using PoE, the AP must be connected to PoE networks without routing cabling to the outside plant—this ensures
that cabling is not exposed to lightning strikes or possible cross over from high voltage.
Battery Warning
UL Statement
Use only with listed ITE product.
RF Radiation Hazard Warning
To ensure compliance with FCC RF exposure requirements, this device must be installed in a location where the
antennas of the device will have a minimum distance of at least 30 cm (12 inches) from all persons. Using higher
gain antennas and types of antennas not certified for use with this product is not allowed. The device shall not be
co-located with another transmitter.
Installation
This device is designed for a specific application and must be installed by qualified personnel with knowledge of
RF and related rules. Please refer to the Quick Installation Guide for the product for installation instructions.
General users shall not attempt to install the device or change its settings.
!Caution! The AP contains a battery which is not to be replaced by the customer. Danger of Explosion exists if
the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.
X2 and XR300 Series Notices and Regulatory Guide
3
Industry Canada Statement (X2)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels
is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection
d'autres canaux n'est pas possible.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with IC multi-transmitter product procedures.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou
transmetteur.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-
5725 MHz
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz
et 5650-5725 MHz
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-
LAN devices.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs
principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient
causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
For indoor use only.
Pour une utilisation en intérieur uniquement.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator and your
body.
!Warning: Please carefully select the installation location and ensure that the final output power does not
exceed local regulatory limits. The violation of this rule could lead to serious official penalties.
X2 and XR300 Series Notices and Regulatory Guide
4
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement and Marking (non-X2)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications
were met. This equipment should be installed and operated with a minimum distance of 30cm between the
radiator and your body.
Cet équipement doit être installé et utilisé à une distance minimale de 30cm entre le radiateur et votre corps.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un
type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
High Power Radars
High power radars are allocated as primary users (meaning they have priority) in the 5250MHz to 5350MHz and
5650MHz to 5850MHz bands. These radars could cause interference and/or damage to LELAN devices used in
Canada.
Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les
bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz. Ces radars pourraient causer du brouillage et/ou des dommages aux
dispositifs LAN-EL.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems;
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l'intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
X2 and XR300 Series Notices and Regulatory Guide
5
EU Directive 1999/5/EC Compliance Information
This section contains compliance information for the Xirrus Wireless AP family of products. The compliance
information contained in this section is relevant to the European Union and other countries that have implemented
the EU Directive 1999/5/EC.
Declaration of Conformity
This document contains Notices, Warnings, and Compliance information for the X2 and XR300 Series
only. For other models, see the notes on page 1.
Cesky [Czech] Toto zahzeni je v souladu se základnimi požadavky a ostatnimi odpovidajcimi ustano
veni mi Směrnice 1999/5/EC.
Dansk [Danish] Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante
bestemmelser i Direktiv 1999/5/EF.
Deutsch [German] Dieses Gerat entspricht den grundlegenden Anforderungen und den weiteren
entsprechenden Vorgaben der Richtinie 1999/5/EU.
Eesti [Estonian] See seande vastab direktiivi 1999/5/EU olulistele nöuetele ja teistele as jakohastele
sätetele.
English This equipment is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Español [Spain] Este equipo cump le con los requisitos esenciales asi como con otras disposiciones de
la Directiva 1999/5/CE.
Ελληνυκη [Greek] Αυτόζ ο εξοπλτσμόζ είναι σε συμμόρφωση με τιζ ουσιώδειζ απαιτήσειζ και ύλλεζ σχετικέζ
διατάξειζ τηζ Οδηγιαζ 1999/5/EC.
Français [French] Cet appareil est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la Directive 1999/5/EC.
ĺslenska [Icelandic] Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar
1999/5/EC.
Italiano [Italian] Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla
Direttiva 1999/5/CE.
Latviski [Latvian] Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajā prasībām un citiem ar to saistītajiem
noteikumiem.
Lietuvių [Lithuanian] Šis įrenginys tenkina 1995/5/EB Direktyvos esminius reikalavimus ir kitas šios
direktyvos nuostatas.
Nederlands [Dutch] Dit apparant voldoet aan de essentiele eisen en andere van toepassing zijnde
bepalingen van de Richtlijn 1995/5/EC.
Malti [Maltese] Dan l-apparant huwa konformi mal-htigiet essenzjali u l-provedimenti l-ohra rilevanti
tad-Direttiva 1999/5/EC.
Margyar [Hungarian] Ez a készülék teljesiti az alapvetö követelményeket és más 1999/5/EK irányelvben
meghatározott vonatkozó rendelkezéseket.
X2 and XR300 Series Notices and Regulatory Guide
6
CE Marking
For the Xirrus Wireless AP, the CE mark and Class-2 identifier opposite are affixed to the equipment and its
packaging:
Assessment Criteria
The following standards were applied during the assessment of the product against the requirements of the
Directive 1999/5/EC:
Radio: EN 301 893 and EN 300 328 (if applicable)
EMC: EN 301 489-1 and EN 301 489-17
Safety: EN 62479, EN 50385 and EN 60950/IEC60950
Norsk [Norwegian] Dette utstyret er i samsvar med de grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
Polski [Polish] Urządzenie jest zgodne z ogólnymi wymaganiami oraz sczególnymi mi warunkami
określony mi Dyrektywą. UE:1999/5/EC.
Portuguès [Portuguese] Este equipamento está em conformidade com os requisitos essenciais e outras
provisões relevantes da Directiva 1999/5/EC.
Slovensko [Slovenian] Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi popoji
Direktive 1999/5/EC.
Slovensky [Slovak] Toto zariadenie je v zhode so základnými požadavkami a inými prislušnými
nariadeniami direktiv: 1999/5/EC.
Suomi [Finnish] Tämä laite täyttää direktiivin 1999/5//EY olennaiset vaatimukset ja on siinä
asetettujen muiden laitetta koskevien määräysten mukainen.
Svenska [Swedish] Denna utrustning är i överensstämmelse med de väsentliga kraven och andra
relevanta bestämmelser i Direktiv 1999/5/EC.
X2 and XR300 Series Notices and Regulatory Guide
7
WEEE Compliance
National Restrictions
In the majority of the EU and other European countries, the 2.4 GHz and 5 GHz bands have been made available
for the use of Wireless LANs. The following table provides an overview of the regulatory requirements in general
that are applicable for the 2.4 GHz and 5 GHz bands.
*Dynamic frequency selection and Transmit Power Control is required in these frequency bands.
**France is indoor use only in the upper end of the band.
The requirements for any country may change at any time. Xirrus recommends that you check with local
authorities for the current status of their national regulations for both 2.4 GHz and 5 GHz wireless LANs.
The following countries have additional requirements or restrictions than those listed in the above table:
Belgium
The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor
wireless link having a range exceeding 300 meters. Xirrus recommends checking at www.bipt.be for more details.
Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden
bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie www.bipt.be voor meer gegevens.
Frequency
Band (MHz) Max Power Level
(EIRP) (mW) Indoor Outdoor
2400–2483.5 100 X X **
5250–5350 *200 X N/A
5470–5725* 1000 X X
Natural resources were used in the production of this equipment.
This equipment may contain hazardous substances that could impact the health of the
environment.
In order to avoid harm to the environment and consumption of natural resources, we
encourage you to use appropriate take-back systems when disposing of this
equipment.
The appropriate take-back systems will reuse or recycle most of the materials of this
equipment in a way that will not harm the environment.
The crossed-out wheeled bin symbol (in accordance with European Standard EN
50419) invites you to use those take-back systems and advises you not to combine the
material with refuse destined for a land fill.
If you need more information on collection, re-use and recycling systems, please
contact your local or regional waste administration.
Please contact Xirrus for specific information on the environmental performance of our
products.
X2 and XR300 Series Notices and Regulatory Guide
8
Les liasons sans fil pour une utilisation en extérieur d’une distance supérieure à 300 mèters doivent être notifiées à
l’Institut Belge des services Postaux et des Télécommunications (IBPT). Visitez www.bipt.be pour de plus amples détails.
Greece
A license from EETT is required for the outdoor operation in the 5470 MHz to 5725 MHz band. Xirrus
recommends checking www.eett.gr for more details.
Η δη ιουργβάικτ ωνεξωτερικο ρουστη ζ νησυ νοτ των 5470–5725 ΜΗz ε ιτρ ετάιωνο ετάά όάδειά της ΕΕΤΤ, ου ορηγεβτάι
στερά ά ό σ φωνη γν η του ΓΕΕΘΑ. ερισσότερες λε τομ ρειεωστο www.eett.gr
Italy
This product meets the National Radio Interface and the requirements specified in the National Frequency
Allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owner’s
property, its use requires a “general authorization.” Please check with www.communicazioni.it/it/ for more details.
Questo prodotto é conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle
frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo di prodotti wireless LAN richiede una
“autorizzazione Generale.” Consultare www.communicazioni.it/it/ per maggiori dettagli.
Norway, Switzerland and Liechtenstein
Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has
also been implemented in those countries.
Calculating the Maximum Output Power
The regulatory limits for maximum output power are specified in EIRP (radiated power). The EIRP level of a
device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at
the connector (specified in dBm).
Antennas
The Xirrus Wireless AP employs integrated antennas that cannot be removed and which are not user accessible.
Nevertheless, as regulatory limits are not the same throughout the EU, users may need to adjust the conducted
power setting for the radio to meet the EIRP limits applicable in their country or region. Adjustments can be made
from the product’s management interface—either Web Management Interface (WMI) or Command Line Interface
(CLI).
Operating Frequency
The operating frequency in a wireless LAN is determined by the access point. As such, it is important that the
access point is correctly configured to meet the local regulations. See National Restrictions in this section for more
information.
If you still have questions regarding the compliance of Xirrus products or you cannot find the information you are
looking for, please contact us at:
Xirrus, Inc.
2101 Corporate Center Drive
Thousand Oaks, CA 91320
USA
Tel: 1.805.262.1600
X2 and XR300 Series Notices and Regulatory Guide
9
1.800.947.7871 Toll Free in the US
Fax: 1.866.462.3980
www.xirrus.com
Compliance Information (Non-EU)
This section contains compliance information for Xirrus XR320 Wireless products for the countries listed below
(outside of the European Union and other countries that have implemented the EU Directive 1999/5/EC).
Declaration of Conformity—Brazil (XR320 only)
Safety Warnings
This document contains Notices, Warnings, and Compliance information for the X2 and XR300 Series
only. For other models, see the notes on page 1.
!Safety Warnings
Read all user documentation before powering this device. All Xirrus interconnected equipment
should be contained indoors. This product is not suitable for outdoor operation. Please verify the
integrity of the system ground prior to installing Xirrus equipment. Additionally, verify that the
ambient operating temperature does not exceed 45°C.
!Explosive Device Proximity Warning
Do not operate the XR Series Wireless AP near unshielded blasting caps or in an explosive
environment unless the device has been modified to be especially qualified for such use.
!Lightning Activity Warning
Do not work on the XR Series Wireless AP or connect or disconnect cables during periods of
lightning activity.
X2 and XR300 Series Notices and Regulatory Guide
0
10
Translated safety warnings appear on the following page.
Translated Safety Warnings
Avertissements de Sécurité
!Circuit Breaker Warning
The XR Series Wireless AP relies on the building’s installation for over current protection. Ensure
that a fuse or circuit breaker no larger than 120 VAC, 15A (U.S.) or 240 VAC, 10A (International) is
used on all current-carrying conductors.
This document contains Notices, Warnings, and Compliance information for the X2 and XR300 Series
only. For other models, see the notes on page 1.
!Sécurité
Lisez l'ensemble de la documentation utilisateur avant de mettre cet appareil sous tension. Tous les
équipements Xirrus interconnectés doivent être installés en intérieur. Ce produit n'est pas conçu
pour être utilisé en extérieur. Veuillez vérifier l'intégrité de la terre du système avant d'installer des
équipements Xirrus. Vérifiez également que la température de fonctionnement ambiante n'excède
pas 45°C.
!Proximité d'appareils explosifs
N'utilisez pas l'unité XR Wireless AP à proximité d'amorces non blindées ou dans un environnement
explosif, à moins que l'appareil n'ait été spécifiquement modifié pour un tel usage.
!Foudre
N'utilisez pas l'unité XR Wireless AP et ne branchez pas ou ne débranchez pas de câbles en cas de
foudre.
!Disjoncteur
L'unité XR Wireless AP dépend de l'installation du bâtiment pour ce qui est de la protection contre
les surintensités. Assurez-vous qu'un fusible ou qu'un disjoncteur de 120 Vca, 15 A (États-Unis) ou
de 240 Vca, 10 A (International) maximum est utilisé sur tous les conducteurs de courant.
X2 and XR300 Series Notices and Regulatory Guide
1
11
Software License and Product Warranty Agreement
THIS SOFTWARE LICENSE AGREEMENT (THE “AGREEMENT”) IS A LEGAL AGREEMENT BETWEEN YOU
(“CUSTOMER”) AND LICENSOR (AS DEFINED BELOW) AND GOVERNS THE USE OF THE SOFTWARE
INSTALLED ON THE PRODUCT (AS DEFINED BELOW). IF YOU ARE AN EMPLOYEE OR AGENT OF
CUSTOMER, YOU HEREBY REPRESENT AND WARRANT TO LICENSOR THAT YOU HAVE THE POWER
AND AUTHORITY TO ACCEPT AND TO BIND CUSTOMER TO THE TERMS AND CONDITIONS OF THIS
AGREEMENT (INCLUDING ANY THIRD PARTY TERMS SET FORTH HEREIN). IF YOU DO NOT AGREE TO
ALL OF THE TERMS OF THIS AGREEMENT RETURN THE PRODUCT AND ALL ACCOMPANYING
MATERIALS (INCLUDING ALL DOCUMENTATION) TO THE RELEVANT VENDOR FOR A FULL REFUND
OF THE PURCHASE PRICE THEREFORE.
CUSTOMER UNDERSTANDS AND AGREES THAT USE OF THE PRODUCT AND SOFTWARE SHALL BE
DEEMED AN AGREEMENT TO THE TERMS AND CONDITIONS GOVERNING SUCH SOFTWARE AND
THAT CUSTOMER IS BOUND BY AND BECOMES A PARTY TO THIS AGREEMENT.
1.0 DEFINITIONS
1.1 “Documentation” means the user manuals and all other all documentation, instructions or other similar
materials accompanying the Software covering the installation, application, and use thereof.
1.2 “Licensor” means Xirrus and its suppliers.
1.3 “Product” means a multi-radio access point containing four or more distinct radios capable of simultaneous
operation on four or more non-overlapping channels.
1.4 “Software” means, collectively, each of the application and embedded software programs delivered to
Customer in connection with this Agreement. For purposes of this Agreement, the term Software shall be
deemed to include any and all Documentation and Updates provided with or for the Software.
1.5 “Updates” means any bug-fix, maintenance or version release to the Software that may be provided to
Customer from Licensor pursuant to this Agreement or pursuant to any separate maintenance and support
agreement entered into by and between Licensor and Customer.
2.0 GRANT OF RIGHTS
2.1 Software. Subject to the terms and conditions of this Agreement, Licensor hereby grants to Customer a
perpetual, non-exclusive, non-sublicenseable, non-transferable right and license to use the Software solely as
installed on the Product in accordance with the accompanying Documentation and for no other purpose.
2.2 Ownership. The license granted under Sections 2.1 above with respect to the Software does not constitute a
transfer or sale of Licensor's or its suppliers' ownership interest in or to the Software, which is solely licensed
to Customer. The Software is protected by both national and international intellectual property laws and
treaties. Except for the express licenses granted to the Software, Licensor and its suppliers retain all rights, title
and interest in and to the Software, including (i) any and all trade secrets, copyrights, patents and other
proprietary rights therein or thereto or (ii) any Marks (as defined in Section 2.3 below) used in connection
therewith. In no event shall Customer remove, efface or otherwise obscure any Marks contained on or in the
Software. All rights not expressly granted herein are reserved by Licensor.
2.3 Copies. Customer shall not make any copies of the Software but shall be permitted to make a reasonable
number of copies of the related Documentation. Whenever Customer copies or reproduces all or any part of
the Documentation, Customer shall reproduce all and not efface any titles, trademark symbols, copyright
symbols and legends, and other proprietary markings or similar indicia of origin (“Marks”) on or in the
Documentation.
2.4 Restrictions. Customer shall not itself, or through any parent, subsidiary, affiliate, agent or other third party (i)
sell, rent, lease, license or sublicense, assign or otherwise transfer the Software, or any of Customer's rights and
obligations under this Agreement except as expressly permitted herein; (ii) decompile, disassemble, or reverse
engineer the Software, in whole or in part, provided that in those jurisdictions in which a total prohibition on
any reverse engineering is prohibited as a matter of law and such prohibition is not cured by the fact that this
Agreement is subject to the laws of the State of California, Licensor agrees to grant Customer, upon Customer's
written request to Licensor, a limited reverse engineering license to permit interoperability of the Software
X2 and XR300 Series Notices and Regulatory Guide
2
12
with other software or code used by Customer; (iii) allow access to the Software by any user other than by
Customer's employees and contractors who are bound in writing to confidentiality and non-use restrictions at
least as protective as those set forth herein; (iv) except as expressly set forth herein, write or develop any
derivative software or any other software program based upon the Software; (v) use any computer software or
hardware which is designated to defeat any copy protection or other use limiting device, including any device
intended to limit the number of users or devices accessing the Product; (vi) disclose information about the
performance or operation of the Product or Software to any third party without the prior written consent of
Licensor; or (vii) engage a third party to perform benchmark or functionality testing of the Product or
Software.
3.0 LIMITED WARRANTY AND LIMITATION OF LIABILITY
3.1 Limited Warranty & Exclusions. Licensor warrants that the Software will perform in substantial accordance
with the specifications therefore set forth in the Documentation for a period of ninety [90] days after
Customer's acceptance of the terms of this Agreement with respect to the Software (“Warranty Period”). If
during the Warranty Period the Software or Product does not perform as warranted, Licensor shall, at its
option, correct the relevant Product and/or Software giving rise to such breach of performance or replace such
Product and/or Software free of charge. THE FOREGOING ARE CUSTOMER'S SOLE AND EXCLUSIVE
REMEDIES FOR BREACH OF THE FOREGOING WARRANTY. THE WARRANTY SET FORTH ABOVE IS
MADE TO AND FOR THE BENEFIT OF CUSTOMER ONLY. The warranty will apply only if (i) the Software
has been used at all times and in accordance with the instructions for use set forth in the Documentation and
this Agreement; (ii) no modification, alteration or addition has been made to the Software by persons other
than Licensor or Licensor's authorized representative; and (iii) the Software or Product on which the Software
is installed has not been subject to any unusual electrical charge.
3.2 DISCLAIMER. EXCEPT AS EXPRESSLY STATED IN THIS SECTION 3, ALL ADDITIONAL CONDITIONS,
REPRESENTATIONS, AND WARRANTIES, WHETHER IMPLIED, STATUTORY OR OTHERWISE,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, ACCURACY,
AGAINST INFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE
PRACTICE, ARE HEREBY DISCLAIMED BY LICENSOR AND ITS SUPPLIERS. THIS DISCLAIMER SHALL
APPLY EVEN IF ANY EXPRESS WARRANTY AND LIMITED REMEDY OFFERED BY LICENSOR FAILS OF
ITS ESSENTIAL PURPOSE. ALL WARRANTIES PROVIDED BY LICENSOR ARE SUBJECT TO THE
LIMITATIONS OF LIABILITY SET FORTH IN THIS AGREEMENT.
3.3 HAZARDOUS APPLICATIONS. THE SOFTWARE IS NOT DESIGNED OR INTENDED FOR USE IN
HAZARDOUS ENVIRONMENTS REQUIRING FAIL SAFE PERFORMANCE, SUCH AS IN THE
OPERATION OF A NUCLEAR FACILITY, AIRCRAFT NAVIGATION OR COMMUNICATIONS SYSTEMS,
AIR TRAFFIC CONTROLS OR OTHER DEVICES OR SYSTEMS IN WHICH A MALFUNCTION OF THE
SOFTWARE WOULD RESULT IN FORSEEABLE RISK OF INJURY OR DEATH TO THE OPERATOR OF THE
DEVICE OR SYSTEM OR TO OTHERS (“HAZARDOUS APPLICATIONS”). CUSTOMER ASSUMES ANY
AND ALL RISKS, INJURIES, LOSSES, CLAIMS AND ANY OTHER LIABILITIES ARISING OUT OF THE USE
OF THE SOFTWARE IN ANY HAZARDOUS APPLICATIONS.
3.4 Limitation of Liability.
(a) TOTAL LIABILITY. NOTWITHSTANDING ANYTHING ELSE HEREIN, ALL LIABILITY OF LICENSOR
AND ITS SUPPLIERS UNDER THIS AGREEMENT SHALL BE LIMITED TO THE AMOUNT PAID BY
CUSTOMER FOR THE RELEVANT SOFTWARE, OR PORTION THEREOF, THAT GAVE RISE TO SUCH
LIABILITY OR ONE HUNDRED UNITED STATES DOLLARS (US$100), WHICHEVER IS GREATER.
THE LIABILITY OF LICENSOR AND ITS SUPPLIERS UNDER THIS SECTION SHALL BE
CUMULATIVE AND NOT PER INCIDENT.
(b) DAMAGES. IN NO EVENT SHALL LICENSOR, ITS SUPPLIERS OR THEIR RELEVANT
SUBCONTRACTORS BE LIABLE FOR (A) ANY INCIDENTAL, SPECIAL, PUNITIVE OR
CONSEQUENTIAL DAMAGES, LOST PROFITS OR LOST OR DAMAGED DATA, OR ANY INDIRECT
DAMAGES, WHETHER ARISING IN CONTRACT, TORT (INCLUDING NEGLIGENCE AND STRICT
LIABILITY) OR OTHERWISE OR (B) ANY COSTS OR EXPENSES FOR THE PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES IN EACH CASE, EVEN IF LICENSOR OR ITS SUPPLIERS HAVE
BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.
X2 and XR300 Series Notices and Regulatory Guide
3
13
3.5 Exclusions. SOME JURISDICTIONS DO NOT PERMIT THE LIMITATIONS OF LIABILITY AND LIMITED
WARRANTIES SET FORTH UNDER THIS AGREEMENT. IN THE EVENT YOU ARE LOCATED IN ANY
SUCH JURISDICTION, THE FOREGOING LIMITATIONS SHALL APPLY ONLY TO THE MAXIMUM
EXTENT PERMITTED IN SUCH JURISDICTIONS. IN NO EVENT SHALL THE FOREGOING EXCLUSIONS
AND LIMITATIONS ON DAMAGES BE DEEMED TO APPLY TO ANY LIABILITY BASED ON FRAUD,
WILLFUL MISCONDUCT, GROSS NEGLIGENCE OR PERSONAL INJURY OR DEATH.
4.0 CONFIDENTIAL INFORMATION
4.1 Generally. The Software (and its accompanying Documentation) constitutes Licensor's and its suppliers'
proprietary and confidential information and contains valuable trade secrets of Licensor and its suppliers
(“Confidential Information”). Customer shall protect the secrecy of the Confidential Information to the same
extent it protects its other valuable, proprietary and confidential information of a similar nature but in no event
shall Customer use less than reasonable care to maintain the secrecy of the Confidential Information.
Customer shall not use the Confidential Information except to exercise its rights or perform its obligations as
set forth under this Agreement. Customer shall not disclose such Confidential Information to any third party
other than subject to non-use and non-disclosure obligations at least as protective of a party's right in such
Confidential Information as those set forth herein.
4.2 Return of Materials. Customer agrees to (i) destroy all Confidential Information (including deleting any and all
copies contained on any of Customer's Designated Hardware or the Product) within fifteen (15) days of the
date of termination of this Agreement or (ii) if requested by Licensor, return, any Confidential Information to
Licensor within thirty (30) days of Licensor's written request.
5.0 TERM AND TERMINATION
5.1 Term. Subject to Section 5.2 below, this Agreement will take effect on the Effective Date and will remain in force
until terminated in accordance with this Agreement.
5.2 Termination Events. This Agreement may be terminated immediately upon written notice by either party
under any of the following conditions:
(a) If the other party has failed to cure a breach of any material term or condition under the Agreement within
thirty (30) days after receipt of notice from the other party; or
(b) Either party ceases to carry on business as a going concern, either party becomes the object of the institution
of voluntary or involuntary proceedings in bankruptcy or liquidation, which proceeding is not dismissed
within ninety (90) days, or a receiver is appointed with respect to a substantial part of its assets.
5.3 Effect of Termination.
(a) Upon termination of this Agreement, in whole or in part, Customer shall pay Licensor for all amounts
owed up to the effective date of termination. Termination of this Agreement shall not constitute a waiver
for any amounts due.
(b) The following Sections shall survive the termination of this Agreement for any reason: Sections 1, 2.2, 2.4,
3, 4, 5.3, and 6.
(c) No later than thirty (30) days after the date of termination of this Agreement by Licensor, Customer shall
upon Licensor's instructions either return the Software and all copies thereof; all Documentation relating
thereto in its possession that is in tangible form or destroy the same (including any copies thereof
contained on Customer's Designated Hardware). Customer shall furnish Licensor with a certificate signed
by an executive officer of Customer verifying that the same has been done.
X2 and XR300 Series Notices and Regulatory Guide
4
14
6. MISCELLANEOUS
If Customer is a corporation, partnership or similar entity, then the license to the Software and Documentation that
is granted under this Agreement is expressly conditioned upon and Customer represents and warrants to Licensor
that the person accepting the terms of this Agreement is authorized to bind such entity to the terms and conditions
herein. If any provision of this Agreement is held to be invalid or unenforceable, it will be enforced to the extent
permissible and the remainder of this Agreement will remain in full force and effect. During the course of use of
the Software, Licensor may collect information on your use thereof; you hereby authorize Licensor to use such
information to improve its products and services, and to disclose the same to third parties provided it does not
contain any personally identifiable information. The express waiver by either party of any provision, condition or
requirement of this Agreement does not constitute a waiver of any future obligation to comply with such
provision, condition or requirement. Customer and Licensor are independent parties. Customer may not export or
re-export the Software or Documentation (or other materials) without appropriate United States, European Union
and foreign government licenses or in violation of the United State's Export Administration Act or foreign
equivalents and Customer shall comply with all national and international laws governing the Software. This
Agreement will be governed by and construed under the laws of the State of California and the United States as
applied to agreements entered into and to be performed entirely within California, without regard to conflicts of
laws provisions thereof and the parties expressly exclude the application of the United Nations Convention on
Contracts for the International Sales of Goods and the Uniform Computer Information Transactions Act (as
promulgated by any State) to this Agreement. Suits or enforcement actions must be brought within, and each party
irrevocably commits to the exclusive jurisdiction of, the state and federal courts located in Ventura County,
California. Customer may not assign this Agreement by operation of law or otherwise, without the prior written
consent of Licensor and any attempted assignment in violation of the foregoing shall be null and void. This
Agreement cancels and supersedes all prior agreements between the parties. This Agreement may not be varied
except through a document agreed to and signed by both parties. Any printed terms and conditions contained in
any Customer purchase order or in any Licensor acknowledgment, invoice or other documentation relating to the
Software shall be deemed deleted and of no force or effect and any additional typed and/or written terms and
conditions contained shall be for administrative purposes only, i.e. to identify the types and quantities of Software
to be supplied, line item prices and total price, delivery schedule, and other similar ordering data, all in accordance
with the provisions of this Agreement.
X2 and XR300 Series Notices and Regulatory Guide
5
15
Hardware Warranty Agreement
PLEASE READ THIS AGREEMENT CAREFULLY BEFORE USING THIS PRODUCT
BY USING THIS PRODUCT, YOU ACKNOWLEDGE THAT YOU HAVE READ AND UNDERSTOOD ALL THE
TERMS AND CONDITIONS OF THIS AGREEMENT AND THAT YOU ARE CONSENTING TO BE BOUND BY
THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, RETURN THE
UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
LIMITED WARRANTY. Xirrus warrants that for a period of five years from the date of purchase by the original
purchaser (“Customer”): (i) the Xirrus Equipment (“Equipment”) will be free of defects in materials and
workmanship under normal use; and (ii) the Equipment substantially conforms to its published specifications.
Except for the foregoing, the Equipment is provided AS IS. This limited warranty extends only to Customer as the
original purchaser. Customer's exclusive remedy and the entire liability of Xirrus and its suppliers under this
limited warranty will be, at Xirrus' option, repair, replacement, or refund of the Equipment if reported (or, upon
request, returned) to the party supplying the Equipment to Customer. In no event does Xirrus warrant that the
Equipment is error free or that Customer will be able to operate the Equipment without problems or interruptions.
This warranty does not apply if the Equipment (a) has been altered, except by Xirrus, (b) has not been installed,
operated, repaired, or maintained in accordance with instructions supplied by Xirrus, (c) has been subjected to
abnormal physical or electrical stress, misuse, negligence, or accident, or (d) is used in ultra-hazardous activities.
DISCLAIMER. EXCEPT AS SPECIFIED IN THIS WARRANTY, ALL EXPRESS OR IMPLIED CONDITIONS,
REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY IMPLIED
WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT OR
ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE, ARE HEREBY EXCLUDED TO THE
EXTENT ALLOWED BY APPLICABLE LAW.
IN NO EVENT WILL Xirrus OR ITS SUPPLIERS BE LIABLE FOR ANY LOST REVENUE, PROFIT, OR DATA, OR
FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR PUNITIVE DAMAGES HOWEVER CAUSED
AND REGARDLESS OF THE THEORY OF LIABILITY ARISING OUT OF THE USE OF OR INABILITY TO USE
THE EQUIPMENT EVEN IF Xirrus OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. In no event shall Xirrus' or its suppliers' liability to Customer, whether in contract, tort (including
negligence), or otherwise, exceed the price paid by Customer.
The foregoing limitations shall apply even if the above-stated warranty fails of its essential purpose. SOME
STATES DO NOT ALLOW LIMITATION OR EXCLUSION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES.
The above warranty DOES NOT apply to any evaluation Equipment made available for testing or demonstration
purposes. All such Equipment is provided AS IS without any warranty whatsoever.
Customer agrees the Equipment and related documentation shall not be used in life support systems, human
implantation, nuclear facilities or systems or any other application where failure could lead to a loss of life or
catastrophic property damage, or cause or permit any third party to do any of the foregoing.
All information or feedback provided by Customer to Xirrus with respect to the Product shall be Xirrus' property
and deemed confidential information of Xirrus.
Equipment including technical data, is subject to U.S. export control laws, including the U.S. Export
Administration Act and its associated regulations, and may be subject to export or import regulations in other
countries. Customer agrees to comply strictly with all such regulations and acknowledges that it has the
responsibility to obtain licenses to export, re-export, or import Equipment.
This Agreement shall be governed by and construed in accordance with the laws of the State of California, United
States of America, as if performed wholly within the state and without giving effect to the principles of conflict of
law. If any portion hereof is found to be void or unenforceable, the remaining provisions of this Warranty shall
remain in full force and effect. This Warranty constitutes the entire agreement between the parties with respect to
the use of the Equipment.
Manufacturer is Xirrus, Inc. 2101 Corporate Center Drive Thousand Oaks, CA 91320
1.800.947.7871 Toll Free in the US
+1.805.262.1600 Sales
+1.805.262.1601 Fax
2101 Corporate Center Drive
Thousand Oaks, CA 91320, USA
To learn more visit:
xirrus.com or
email info@xirrus.com
© 201 Xirrus, Inc. All Rights Reserved. The Xirrus logo is a registered trademark of Xirrus, Inc.
All other trademarks are the property of their respective owners. Content subject to change without notice.
812-0142-001 Rev D