Cambridge Audio Topaz Sr10 Users Manual

SR10 to the manual a7405647-e8bd-45a4-ade4-0bbce2c4d5be

2015-02-02

: Cambridge-Audio Cambridge-Audio-Topaz-Sr10-Users-Manual-420790 cambridge-audio-topaz-sr10-users-manual-420790 cambridge-audio pdf

Open the PDF directly: View PDF .
Page Count: 12

Your music +our passion

SR10

ENGLISH

Stereo receiver

User’s manual

Thank you for purchasing this Cambridge Audio Topaz SR10 Stereo

Receiver. We are confident that you will enjoy many years of listening

pleasure from it. Like all Cambridge Audio products, the SR10 adheres to

three core principles – stunning performance, ease of use and incredible

value.

Our usual attention to detail is present with a completely discrete high

power bipolar transistor based power amplifier, very quiet speed

controlled fan cooling and a custom low flux toroidal transformer for

audiophile audio performance.

The built-in FM/AM tuner features RDS for station name display on FM

stations that support this function.

The unit can support a wide range of external sources and a front panel

MP3/Portable Media Player input has been fitted which can be used with

the headphone or line-level outputs of most portable players.

The supplied remote control can control this receiver and its built in tuner

plus the matching CD5 or CD10 CD players if required.

Part of our new Topaz range this product also features a new casework

design with braced front panel, rigid wrap-over lid assembly and carefully

designed mechanicals for resonance control.

Your receiver can only be as good as the system it is connected to. Please

do not compromise on the quality of your source equipment, speakers or

cabling. Naturally, we particularly recommend source and speaker models

from the Cambridge Audio range, which have been designed to the same

exacting standards as this product. Your dealer can also supply excellent

quality Cambridge Audio interconnects to ensure your system realises its

full potential.

Thank you for taking the time to read this manual; we recommend you

keep it for future reference.

Matthew Bramble

Cambridge Audio Technical Director

and the SR10 design team

Contents Introduction

Introduction .................................................................................................2

Important safety instructions .....................................................................3

Limited warranty..........................................................................................4

Rear panel connections..............................................................................5

Aerials ..........................................................................................................5

Front panel controls....................................................................................6

Remote control............................................................................................7

Connections.................................................................................................8

Operating instructions ..............................................................................10

Technical specifications ...........................................................................11

Troubleshooting.........................................................................................11

Make sure you register your purchase.

Visit: www.cambridge-audio.com/sts

By registering, you’ll be the first to know about:

GFuture product releases

GSoftware upgrades

GNews, events and exclusive offers plus

competitions!

This guide is designed to make installing and using this product as easy

as possible. Information in this document has been carefully checked

for accuracy at the time of printing; however, Cambridge Audio's policy

is one of continuous improvement, therefore design and specifications

are subject to change without prior notice.

This document contains proprietary information protected by copyright.

All rights are reserved. No part of this manual may be reproduced by any

mechanical, electronic or other means, in any form, without prior written

permission of the manufacturer. All trademarks and registered

trademarks are the property of their respective owners.

SR10

ENGLISH

For your own safety please read the following important safety instructions

carefully before attempting to connect this unit to the mains power supply.

They will also enable you to get the best performance from and prolong

the life of the unit:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other. A

grounding-type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly

at plugs, convenience receptacles and the point where they exit from

the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use with only the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as the

power-supply cord or plug having been damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate normally, or has

been dropped.

WARNING

– To reduce the risk of fire or electric shock, do not expose this unit to

rain or moisture.

– Batteries (battery pack or batteries installed) shall not be exposed to

excessive heat such as sunshine, fire or the like.

The unit must be installed in a manner that makes disconnection of the

mains plug from the mains socket outlet (or appliance connector from the

rear of the unit) possible. Where the mains plug is used as the disconnect

device, the disconnect device shall remain readily operable. Only use the

mains cord supplied with this unit.

Please ensure there is ample ventilation (at least 10cm clearance all

round). Do not put any objects on top of this unit. Do not situate it on a rug

or other soft surface and do not obstruct any air inlets or outlet grilles. Do

not cover the ventilation grilles with items such as newspapers,

tablecloths, curtains, etc.

This unit must not be used near water or exposed to dripping or splashing

water or other liquids. No objects filled with liquid, such as vases, shall be

placed on the unit.

The lightning flash with the arrowhead symbol within an equilateral

triangle is intended to alert the user to the presence of un-insulated

‘dangerous voltage’ within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance instructions

in the service literature relevant to this appliance.

The symbol on this product indicates that it is of CLASS II

(double insulated) construction.

WEEE symbol

The crossed-out wheeled bin is the European Union symbol for

indicating separate collection for electrical and electronic

equipment. This product contains electrical and electronic

equipment which should be reused, recycled or recovered and

should not be disposed of with unsorted regular waste. Please return the

unit or contact the authorised dealer from whom you purchased this

product for more information.

CE mark

This product complies with European Low Voltage

(2006/95/EC), Electromagnetic Compatibility (2004/108/EC) and

Environmentally-friendly design of Energy-using Products (2005/32/EC)

Directives when used and installed according to this instruction manual.

For continued compliance only Cambridge Audio accessories should be

used with this product and servicing must be referred to qualified service

personnel.

C-Tick mark

This product meets the Australian Communications Authority’s

Radio communications and EMC requirements.

Ross Test Stamp

This product meets Russian electronic safety approvals.

FCC regulations

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR

TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY

TO OPERATE THE EQUIPMENT.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of

the following measures:

– Re-orient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Important safety instructions

Ventilation

IMPORTANT - The unit will become hot when in use. Do not stack multiple

units on top of each other. Do not place in an enclosed area such as a

bookcase or in a cabinet without sufficient ventilation.

Ensure that small objects do not fall through any ventilation grille. If this

happens, switch off immediately, disconnect from the mains supply and

contact your dealer for advice.

Positioning

Choose the installation location carefully. Avoid placing it in direct sunlight

or close to a source of heat. No naked flame sources, such as lighted

candles, should be placed on the unit. Also avoid locations subject to

vibration and excessive dust, cold or moisture. The unit can be used in a

moderate climate.

This unit must be installed on a sturdy, level surface. Do not place in a

sealed area such as a bookcase or in a cabinet. Do not place the unit on

an unstable surface or shelf. The unit may fall, causing serious injury to a

child or adult as well as serious damage to the product. Do not place other

equipment on top of the unit.

Due to stray magnetic fields turntables or CRT TVs should not be located

nearby due to possible interference.

Electronic audio components have a running in period of around a week

(if used several hours per day). This will allow the new components to

settle down, the sonic properties will improve over this time.

Power sources

The unit should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power-supply to your

home, consult your product dealer or local power company.

To turn the unit off, switch off on the front panel. If you do not intend to

use this unit for a long period of time, unplug it from the mains socket.

Overloading

Do not overload wall outlets or extension cord as this can result in a risk

of fire or electric shock. Overloaded AC outlets, extension cords, frayed

power cords, damaged or cracked wire insulation, and broken plugs are

dangerous. They may result in a shock or fire hazard.

Be sure to insert each power cord securely. To prevent hum and noise, do

not bundle the interconnect leads with the power cord or speaker leads.

Cleaning

To clean the unit, wipe its case with a dry, lint-free cloth. Do not use any

cleaning fluids containing alcohol, ammonia or abrasives. Do not spray an

aerosol at or near the unit.

Battery disposal

Please dispose of any discharged batteries according to local

environmental/electronic waste disposal guidelines.

Loudspeakers

Before making any connections to loudspeakers, make sure all power is

turned off and only use suitable interconnects.

Servicing

These units are not user serviceable, never attempt to repair, disassemble

or reconstruct the unit if there seems to be a problem. A serious electric

shock could result if this precautionary measure is ignored. In the event

of a problem or failure, please contact your dealer.

Cambridge Audio warrants this product to be free from defects in

materials and workmanship (subject to the terms set forth below).

Cambridge Audio will repair or replace (at Cambridge Audio's option) this

product or any defective parts in this product. Warranty periods may vary

from country to country. If in doubt consult your dealer and ensure that

you retain proof of purchase.

To obtain warranty service, please contact the Cambridge Audio

authorised dealer from which you purchased this product. If your dealer is

not equipped to perform the repair of your Cambridge Audio product, it

can be returned by your dealer to Cambridge Audio or an authorised

Cambridge Audio service agent. You will need to ship this product in either

its original packaging or packaging affording an equal degree of

protection.

Proof of purchase in the form of a bill of sale or receipted invoice, which is

evidence that this product is within the warranty period, must be

presented to obtain warranty service.

This Warranty is invalid if (a) the factory-applied serial number has been

altered or removed from this product or (b) this product was not

purchased from a Cambridge Audio authorised dealer. You may call

Cambridge Audio or your local country Cambridge Audio distributor to

confirm that you have an unaltered serial number and/or you purchased

from a Cambridge Audio authorised dealer.

This Warranty does not cover cosmetic damage or damage due to acts of

God, accident, misuse, abuse, negligence, commercial use, or

modification of, or to any part of, the product. This Warranty does not

cover damage due to improper operation, maintenance or installation, or

attempted repair by anyone other than Cambridge Audio or a Cambridge

Audio dealer, or authorised service agent which is authorised to do

Cambridge Audio warranty work. Any unauthorised repairs will void this

Warranty. This Warranty does not cover products sold AS IS or WITH ALL

FAULTS.

REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE

THE EXCLUSIVE REMEDY OF THE CONSUMER. CAMBRIDGE AUDIO SHALL

NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS

PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY

IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED

WARRANTIES WHATSOEVER INCLUDING, BUT NOT LIMITED TO, THE

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL

PURPOSE.

Some countries and US states do not allow the exclusion or limitation of

incidental or consequential damages or implied warranties so the above

exclusions may not apply to you. This Warranty gives you specific legal

rights, and you may have other statutory rights, which vary from state to

state or country to country.

For any service, in or out of warranty, please contact your dealer.

Limited warranty

Plug Fitting Instructions (UK Only)

The cord supplied with this appliance is factory fitted with a UK mains plug fitted

with a 3 amp fuse inside. If it is necessary to change the fuse, it is important that

a 3 amp one is used. If the plug needs to be changed because it is not suitable for

your socket, or becomes damaged, it should be cut off and an appropriate plug

fitted following the wiring instructions below. The plug must then be disposed of

safely, as insertion into a mains socket is likely to cause an electrical hazard.

Should it be necessary to fit a 3-pin BS mains plug to the power cord the wires

should be fitted as shown in this diagram. The colours of the wires in the mains

lead of this appliance may not correspond with the coloured markings identifying

the terminals in your plug. Connect them as follows:

The wire which is coloured BLUE must be

connected to the terminal which is marked

with the letter ‘N’ or coloured BLACK.

The wire which is coloured BROWN must be

connected to the terminal which is marked

with the letter ‘L’ or coloured RED.

The wire which is coloured GREEN/YELLOW

must be connected to the terminal which is

marked with the letter ‘E’ or coloured GREEN.

If a 13 amp (BS 1363) plug is used, a 3 amp fuse must be fitted, or if any other

type of plug is used a 3 amp fuse must be fitted, either in the plug or adaptor, or

on the distribution board.

Mains Voltage Selector Switch

115V/230V AC~50/60Hz

Power AC

Caution

Serial Number Label Removed

BD / DVD MP3 / Aux

MM Phono Rec Out

Ground

BD / DVD

MP3 / Aux

MM PhonoRec Out

Right

Left

Right

Left

Loudspeaker Terminals

Impedance 4–8 ohms

LeftRight

Left Right

Made under licence in China

Manufactured in an

ISO9001 approved facility

This device complies with part 15 of the FCC

Rules. Operation is subject to the condition that

this device does not cause harmful interference.

AM 300ΩFM 75ΩService Port

Do not obstruct ventilation / Ventilation nicht verschließen /

Ne pas obstruer la ventilation

Important

Please ensure that loudspeaker terminals are fully tightened.

Veuillez s'assurer que les bornes de l'enceinte sont

entièrement serrées

Europe FM: 87.50MHz - 108.00MHz

US FM: 87.50MHz - 108.00MHz

Europe AM: 522kHz - 1629kHz

US AM: 530kHz - 1710kHz

CONFORMS TO ANSI/UL

STD 60065

7TH EDITION 2003

CERTIFIED TO CAN/CSA

STD C22.2

No. 60065-03

3132407

Rated Power Consumption: 500W

Designed and engineered in London, England

Topaz SR10 Stereo Receiver

www.cambridge-audio.com

SR10

ENGLISH

Rear panel connections

Audio inputs

These inputs are suitable for any ‘line level’ source equipment such as the

audio outputs of CD players, BD/DVD players, etc.

Phono input

This input has a built in phono stage. Record players fitted with Phono

Cartridges of the Moving Magnet (MM) or high output Moving Coil (MC)

type (between 2-6mV output and 30-50k load impedance) can be used.

Low output Moving Coil types (<1mV and usually 10-1000 ohm load

impedance) cannot be directly connected and will require a matching

transformer or head amp. Please consult your dealer for details. The

‘ground’ terminals on both the record player and the SR10 should be

connected (where possible) with a ground wire for lowest noise/hum

pickup.

Rec Out

Connect to the recording input of a tape deck, CD recorder input, etc.

AM/FM antenna

Tuner aerial connections for picking up radio signals. Refer to the

‘Connections’ section of this manual. For permanent use, outdoor AM/FM

aerials are highly recommended.

Service port

For servicing use only. Do not connect anything here as it may result in

damage.

Loudspeaker terminals

Two sets of loudspeaker terminals are available, A(main loudspeaker

terminals, top row) and B(secondary switchable loudspeaker terminals,

bottom row). Connect the wires from your left channel loudspeaker to the

Left positive and negative terminals, and the wires from the right channel

loudspeaker to the Right positive and negative terminals.

In each case, the red terminal is the positive output and the black

terminal is the negative output.

Care should be taken to ensure no stray strands of wire are shorting

speaker outputs together. Please ensure that the loudspeaker terminals

have been tightened adequately to provide a good electrical connection.

It is possible for the sound quality to be affected if the screw terminals are

loose.

The use of A and B speakers affords you an easy and inexpensive way to

create a simple multi-room system.

Note: When using two pairs of speakers, use speakers with a nominal

impedance of 8 ohms.

Voltage select switch

For servicing use only.

AC power socket

Once all connections are complete, plug the AC power cable into an

appropriate mains socket and turn the unit on.

2 3

Aerials

Note: The SR10 is supplied with a temporary aerial for initial use. For

permanent use, outdoor aerials are highly recommended.

AM loop aerial

Connect each end of the single length antenna to the antenna terminals.

Place the antenna as far from the main system as possible to prevent

unwanted noise and to obtain optimum reception. If the AM loop aerial

provided does not provide sufficient reception, it may be necessary to use

an outdoor AM aerial.

FM aerial

Connect the supplied aerial to the FM 75 ohm socket. Extend and move

the aerial lead around until you get the best reception. For continued use,

we strongly recommend using a 75 ohm outdoor FM aerial.

MM Phono Rec Ou

DVD

MP3

Pho

Rec

Out

Right

Lef

spea

erm

Impedance 4–8 ohms

M 300

Ω

M 75

Ω

Service Por

Rated Power

onsumption

500W

gne

eng

neere

on,

Topaz SR10 Stereo Receiver

ww.cam

idg

e-au

o.co

AM 300ΩFM 75Ω

Speaker A/B button

The Speaker A/B button toggles between the two sets of loudspeaker

terminals. The options are speaker A only, speaker B only, speaker A and

B together, and both sets of speakers off.

Note: ‘Speaker off’ is different to the mute function, as the Rec Out and

Headphones outputs are still enabled.

Menu button

Pressing this once will select the Bass option. Pressing a second time will

select the Treble option and pressing a third time will select the Balance

option. When one of these options is selected, the volume control will

adjust the level. If nothing is pressed for a while, the source will be

displayed and the volume control will go back to controlling the volume

level.

Infrared sensor

Receives IR commands from the supplied remote control. An

unobstructed line of sight between the remote control and the sensor is

required.

Volume control

Use to increase or decrease the level of the sound from the outputs of the

unit. This controls the volume level of the loudspeakers and headphones.

It does not affect the level of the ‘Rec Out’ output. The volume control will

also change the level of bass, treble and balance in the menu options.

MP3 input socket

This source input allows you to connect a portable audio device such as

an MP3 player directly into the front of the unit using a 3.5mm stereo-jack.

Once plugged in, this input is automatically selected, although other

inputs can still be selected once a stereo-jack is plugged in. The MP3/AUX

button on the front of the unit will select this input whilst a stereo-jack is

plugged in.

Note:

– Plugging a source into the front panel MP3 input overrides the Aux input.

Simply remove the jack from the front panel to automatically re-enable

the Aux input.

– Also note that as the output level of MP3 players tends to be quite low,

the SR10 adds 10dB to the current volume setting when (and only

when) the MP3 input is selected.

SR10

Stereo Receiver

Phones Mode / Store

Volume

On / Off

Speaker A / B

1 / 6 2 / 7 3 / 8 4 / 9 5 / 10

MP3 In

PhonoMP3 / AuxBD / DVDCDFM / AM

Front panel controls

1 2 3 4

Power On/Off

Switches the unit on or off.

Headphones socket

Allows for the connection of stereo headphones with a ¼ inch jack plug.

Headphones with an impedance of between 32 and 600 ohms are

recommended.

Note: Plugging in headphones will automatically mute the loudspeaker

outputs.

Skip/Scan buttons

The skip scan buttons are used when the FM/AM tuner is selected. These

buttons have different uses depending on the mode selected:

In Preset mode - Steps up or down through the user-stored presets.

In Auto mode - Searches for the previous or next available station. The

unit stops at the next strong signal it finds.

In Manual mode - Allows manual stepping up or down of the frequency.

Note: When Preset mode is activated, the unit will automatically tune to

the first available preset.

Mode/Store button

Used for AM/FM mode. Press to cycle the tuning mode between Preset,

Auto, and Manual modes. Pressing and holding the button will allow the

current selected station frequency to be stored in the preset bank. First

press and hold the button then use the  or Preset buttons to select

the preset location for the station to be stored to. Press the Mode/Store

button again to confirm and store the preset.

Note: In ‘Store’ mode, if no button is pressed for a while, the unit will come

out of ‘Store’ mode and the preset will not be saved.

Input source buttons (CD, BD/DVD, MP3/Aux,

FM/AM, Phono)

Press the relevant source button to select the desired input source.

Note: The FM/AM source is built into the SR10. This button toggles

between the FM mode and AM mode when pressed more than once.

Preset buttons (1/6, 2/7, 3/8, 4/9, 5/10)

Used for AM/FM modes. The preset buttons are used to select user-stored

station presets. Pressing a preset button once will select one of the first 5

preset, then pressing the same preset button again will toggle to the next

preset (1 and then 6 for instance). These presets are stored separately for

each waveband i.e. there are 10 for FM and 10 for AM press the FM/AM

button to switch between bands and sets of 10 presets.

Note: As well as these 10 per band available directly from the front panel

buttons a further 5 presets (11-15) per band can also be accessed by

using the up/down buttons to cycle through all 15 presets.

Display

Used to display information such as the selected input source, volume and

tone/balance levels. When the FM or AM tuner input is selected, the radio

frequency or RDS station name will be displayed.

Note: When first purchased, the display will have a protective film over the

top. Peel this off for a clear display.

SR10

ENGLISH

Remote control

The Topaz SR10 is supplied with a remote control that operates this unit

and its built-in tuner. In addition, the buttons with Blue coloured icons can

operate a matching Topaz CD5 or CD10 player.

Always use Alkaline batteries.

CD5/CD10 (Blue coloured icons)

To operate the Topaz CD5 or CD10 players only. For more information refer

to the Topaz CD5 and CD10 user’s manual.

Mute

Mutes audio on the unit. Press again to cancel mute.

Speaker A/B

Toggles between the selected loudspeaker terminals: speaker A only,

speaker B only, speaker A and B together, or all speakers off.

Stereo/Mono

Used only when FM is selected. Toggles between FM stereo output and FM

mono output. For low quality stereo FM signals, selecting mono can

usually reduce the noise. Note: Some FM stations are mono only, and

selecting Stereo will have no affect on these.

Mode

Used for AM/FM mode. Press to cycle the tuning mode between Preset,

Auto, and Manual modes.

Volume

Increases or decreases the volume of the unit. Also used to change the

bass, treble and balance settings when these are selected.

Skip

Used when FM or AM is selected.

In Preset mode - Steps up or down through the user-stored presets.

In Auto mode - Search for the previous or next available station with a

strong signal.

In Manual mode - Adjusts the frequency in steps, for fine tuning.

Toggles between Bass, Treble and Balance options. Use the volume

buttons to change the level of the selected option.

Preset buttons (1/5, 2/6, 3/7, 4/8)

Used when FM or AM is selected. These select user-stored station presets.

Pressing a preset button once will select one of the first 4 presets, then

pressing the same preset button again will toggle to the next preset. 8

presets are available directly from the remote, further presets can be

selected in Preset mode, by using the Skip/Scan buttons.

Source buttons (CD, FM, AM, BD/DVD, MP3/Aux, Phono)

Press the relevant button to select the desired music source.

Prog

Speaker

A/B

1/5 2/6 3/7 4/8

Mode

Prog

Clear

Stereo

/ Mono

Random Remain

Repeat

CD AMFM

BD/DVD Phono

MP3/Aux

Presets

CD5/CD10

Note: All connections are made using standard loudspeaker cable.

Basic connection

The diagram below shows the basic connection of your unit to a

CD player and a turntable and a pair of loudspeakers.

Connections

Loudspeakers

Check the impedance of your speakers. When using a pair of speakers,

you can use types with an impedance of between 4 and 8 Ohms. When

using two pairs of speakers, you must use types with an impedance of 8

Ohms each, see later section.

The red coloured speaker terminals are positive (+) and the black speaker

terminals are negative (-). Make sure correct polarity is maintained at

each speaker connector or the sound can become weak and “phasey”

with little bass.

Using bare wire connections

Prepare the speaker cords for connection by stripping off approximately

10mm (3/8”) or less of the outer insulation. More than 10mm could

cause a short circuit. Twist the wires tightly together so there are no loose

ends. Unscrew the speaker terminal, insert the speaker cable, tighten

the terminal and secure the cable.

Mains Voltage Selector Switch

115V/230V AC~50/60Hz

Power AC

BD / DVD MP3 / Aux

MM Phono Rec Out

Ground

BD / DVD

MP3 / Aux

MM PhonoRec Out

Right

Left

Right

Left

Loudspeaker Terminals

Impedance 4–8 ohms

LeftRight

Left Right

Manufactured in an

ISO9001 approved facility

AM 300ΩFM 75ΩService Port

SR10

Right

speaker

Left

speaker

CD player

Red

Red Black Black Red

Black RedBlack

Turntable

SR10

ENGLISH

Mains Voltage Selector Switch

115V/230V AC~50/60Hz

Power AC

CD BD / DVD MP3 / Aux MM Phono Rec Out

Ground

BD / DVD

MP3 / Aux

MM PhonoRec Out

Right

Left

Right

Left

Loudspeaker Terminals

Impedance 4–8 ohms

LeftRight

Left Right

Manufactured in an

ISO9001 approved facility AM 300ΩFM 75ΩService Port

Loudspeaker Terminals

Impedance 4–8 ohms

LeftRight

Left Right

Speaker B connections

The Speaker B connections on the back of the ampliﬁer allow for a second

set of speakers to be used (i.e. speakers located in another room).

The Speaker A/B button on the front panel and remote control allows the

two sets of speakers to be toggled on and off. Refer to the Front Panel or

Remote Control section of this manual for more information on the

Speaker A/B operation.

Bi-wire connections

If your loudspeakers are equipped with two sets of terminals, then it is

possible to connect them in the bi-wire conﬁguration. Bi-wiring sends the

bass and treble frequencies down separate speaker cables, resulting in

a clearer, more focussed sound.

Note:

– Speaker A and B must both be selected for this type of connection to

work.

– Remove the bi-wire link on the speaker terminals before connecting.

Refer to your speakers’ manual for more information.

SR10

Speaker A

Main Room

Speaker B

Room Two

Either A or B, or both A and B may be selected for use.

Note: When using two pairs of speakers, use speakers with a nominal

impedance of 8 ohms each.

Right

speaker

Left

speaker

Red Red Black Black Red

Black RedBlack

Red

Black RedBlack

When Auto mode has been selected, press the button to scroll down

through the station frequencies or press the button to scroll up through

the station frequencies.

The tuner will stop at the ﬁrst strong signal it ﬁnds. To move to another

station simply press the or button again.

Setting presets

Radio stations can be stored into the memory presets for easy access.

You can store up to 15 presets for each band (i.e. 15 presets for the AM

band plus 15 presets for the FM band).

Tune to the station you wish to store and hold down the Mode/Store

button on the front of the unit. The display on the unit will ﬂash the next

available preset.

Press the Mode/Store button again to store the preset. The available

preset will stop ﬂashing to indicate that the station has been stored.

To change the preset number, simply press and hold the Mode/Store

button to enter store mode then select any preset number you require

with the and keys then press the Mode/Store button again to

actually save the preset.

To recall a stored preset, simply press the number on the remote control

that corresponds with the preset. Each of the preset buttons can select

two presets. To select the second preset on the button, press the button

again and this will toggle to the second preset.

To load a stored preset from the front of the unit, simply press the number on

the front the unit or remote that corresponds with the preset. To access the

second preset represented by the button, you must press and hold the button.

Note: You can only access stored presets 1-8 on the remote preset

buttons. You can access stored presets 1-10 on the front panel preset

buttons. To access all presets, set the mode to ‘Preset’ mode with the

‘Mode’ button on the remote control or ‘Mode/Store’ button on the front

panel, and use the or buttons. This will allow access to the full 15

AM stored presets or 15 FM stored presets.

Resetting tuner presets

To clear all stored presets for both AM and FM, press and hold both the

5/10 and Menu buttons at the same time. The unit will display ‘Reset’.

Restart the unit by powering off and on.

After making any connections to your unit, activate the Topaz SR10 by

pressing the On/Off button on the front of the unit.

Setting the source

Press the Source button on the front of the unit corresponding to your

desired source. Alternatively, you may use the appropriate button on the

remote control.

Adjusting the volume

Use either the Volume Up/Down buttons on the remote control, or the

Volume control on the front of your unit system to change the volume

level. The newly selected level will be indicated brieﬂy on the front display.

The volume is displayed in minus dB where 0dB is the highest level.

A progressively larger negative number indicates the volume is being

reduced.

Adjusting the audio settings

Adjustments to the bass, treble and balance can be made as follows:

1. To enter the audio menu. Press either the Menu button on the front of

the unit or on the remote control.

2. Step through the available settings by pressing the Menu button. The

settings available are in order Bass, Treble and Balance.

3. When you wish to make an adjustment for bass, treble or balance,

simply rotate the Volume control or use the Volume control buttons on

the remote control.

4. To exit, wait for ﬁve seconds, until the unit returns to normal mode.

Tuning and listening to the built in tuner

Select the Tuner source using the FM/AM button on the front of the unit,

or directly by pressing the FM or AM buttons on the remote.

Repeatedly pressing the FM/AM button on the front of the unit switches

between FM and AM modes.

Note: For ease of tuning on ﬁrst time use, we recommend that you set the

Topaz SR10 to ‘Auto’ mode. Press the Mode/Store button on the front of

the unit. This button cycles through Preset, Auto and Manual, modes.

Operating instructions

Speaker A / BPhonoMP3 / AuxBD / DVDCDFM / AM BD

eaker

Mode / Store

1 / 6 2 / 7 3 / 8 4 / 9 5 / 10

1/5 2/6 3/7 4/8

Presets

Speaker A / BPhonoMP3 / AuxBD / DVDCDFM / AM

eaker

SR10

ENGLISH

Technical specifications

Power output 85 watts (into 8Ω)

THD (unweighted) <0.01% @ 1kHz, 80% of rated power

<0.15% 20Hz - 20kHz, 80% of rated power

Frequency response (-1dB) 5Hz - 50kHz

S/N ratio (ref 1W) >82dB (unweighted)

Input impedances 47k ohms

Power Amp damping factor >50

Max. power consumption 500W

Bass/Treble controls Shelving, ultimate boost/cut

+/- 10dB @ 100Hz and 20kHz

Dimensions 110 x 430 x 340mm

(4.3 x 16.9 x 13.4”)

Weight 8.1kg (17.8lbs)

Tuners

Bands European

AM (522-1629kHz)

FM (87.5-108MHz)

AM (530-1710kHz)

FM (87.5-108MHz)

Aerial inputs FM 75 ohms, Coaxial.

AM 300 ohms wire loop/single wire.

Signal to noise 60dB typical (FM)

Distortion <0.4% @ 1kHz 50kHz deviation (FM mono)

<0.6% @ 1kHz 50kHz deviation (FM stereo)

Troubleshooting

There is no power

Ensure the AC power cord is connected securely.

Ensure the plug is fully inserted into the wall socket and is switched on.

Check fuse in the mains plug or adaptor.

Check the power is on at the front of the unit.

There is no sound

Check the correct input is selected.

Check that the speakers are connected correctly.

If using the tuner, check aerial connections and an available station is

selected.

Check the unit is not in mute mode.

Check the Speaker A/B configuration matches your speakers.

The sound is distorted

Check aerial connections and placements.

Check speaker connections.

There is a hum coming from the speaker

Ensure that all cable connections are secure, particularly ground/shield

connections. For turntables.

There is unwanted background noise and interference

Move the unit away from other electrical equipment that is likely to cause

interference.

Re-orientate the aerial.

Ensure that all cable connections are secure, particularly ground/shield

connections for turntables.

The remote handset will not function

Check that the batteries have not expired.

Ensure that nothing is blocking the remote sensor.

Over temperature protection

The unit has an over temperature and shutdown protection. If the unit is

continuously used for a long period and over heats, the unit will shut

down. Leave the unit ‘ON’ for 10 minutes to cool down, then turn the unit

off and on to continue listening.

If the problem persists, then the unit is being over driven. Reduce the

volume level, and ensure the unit is in an open ventilated area to resolve

the problem.

Use of two pairs of speakers which are less than 8 Ohms can cause

overloading and is not recommended.

In the event that the above solutions do not remedy your problem, please

consult our frequently asked questions (FAQ) section on our website:

www.cambridge-audio.com/sts/faqs

For all servicing, in or out of warranty, please contact your dealer.

Tuner settings

It is possible to change the tuner region settings for this unit. This can be

necessary if the unit has been moved to a different country.

Two settings are possible which set the correct de-emphasis and tuning

steps for either North America or Europe/Rest of the world.

Note: Changing the tuner settings will clear all stored presets. When

moving the unit to another region the Voltage Select switch must be set to

the correct mains supply voltage by an authorized dealer.

Press and hold both the 4/9 and Menu buttons at the same time. The

display will show the software revision and followed by either a letter ‘A’

which represents North America or a letter ‘E’ which represents

Europe/Rest of the world. Restart the unit by powering off and on.

1 / 6 2 / 7 3 / 8 4 / 9 5 / 10

AP25535/1

Cambridge Audio is a brand of Audio Partnership Plc

Registered Office: Gallery Court, Hankey Place,

London, SE1 4BB, United Kingdom

Registered in England No. 2953313

www.cambridge-audio.com

Cambridge Audio Topaz Sr10 Users Manual

SR10 to the manual a7405647-e8bd-45a4-ade4-0bbce2c4d5be

Navigation menu

Versions of this User Manual:

Views

Navigation