Cameo Communications CLM30001300 11ac 3x3 WIFI Adapter User Manual

Cameo Communications Inc 11ac 3x3 WIFI Adapter Users Manual

Users Manual

Communications, Inc.Page 1Product FeaturesStandard: 802.11ac/a/nInterface: PCI ExpressChipset: Qualcomm Atheros QCA9880Antenna: 3 x U.FL connectors, 3T3RData rate up to 1.3Gbps (VHTMCS9)Enhanced wireless security: 64/128-bits WEP, WPA, WPA2, 802.1xSupport Linux802.11ac 5GHz SolutionThe card is an 802.11ac/a/n 5GHz Single-Band Mini PCI express module based on QualcommAtheros QCA9880 chipset. It supports 3T3R (3x3) technology, which runs up to 433Mbps (11anMSC15) and 1.3Gbps (11ac VHTMCS9). It supports 20/40/80MHz and 256-QAM to maximizebandwidth efficiency.Higher throughput for Enterprise NetworkingAdopting the latest 802.11ac solution, the card is ideal for next-generation high throughput enterprisenetworking solution.Secure Wireless ConnectionIncorporated with advanced security encryption, such as 64/128-bits WEP, WPA, WPA2, and 802.1x,it helps prevent users’ devices from malicious attacks.
Communications, Inc.Page 2SpecificationItem Detailed DescriptionStandard IEEE 802.11ac/ a / nChipset Qualcomm Atheros QCA9880Host Interface PCI expressForm Factor Mini PCI Express (Mini Card)Data Rate 802.11a: 6~54Mbps802.11n: MCS0 ~ MCS15802.11ac: VHTMCS0-9Antenna 3 x U.FL connectors, 3T3ROperatingFrequency11ac ISM Band: 5.150GHz ~ 5.825GHz*subject to local regulationsModulation 802.11a: OFDM (BPSK, QPSK,16-QAM, 64-QAM)802.11n: OFDM (BPSK, QPSK,16-QAM, 64-QAM)802.11ac: OFDM (BPSK, QPSK,16-QAM, 64-QAM, 256-QAM)Output Power(1T)802.11a: 14.5dBm ± 2dBm@54Mbps802.11an (HT20): 15dBm ± 2dBm@MCS7802.11an (HT40): 15dBm ± 2dBm@MCS7802.11ac(HT80): 13dBm ± 2dBm@VHTMCS9*follow FCC certification regulationReceive Sensitivity(1R)802.11a: ≤ -68dBm@54Mbps 802.11an (HT20): ≤ -66dBm@MCS7 802.11an( HT40): ≤ -63dBm@MCS7 802.11ac (HT80): ≤ -51dBm@VHTMCS9 Operating Voltage DC 3.3V ± 10% I/O supply voltage (PCI Express slot support)Environmental Temperature Range: 0 ~ 40°C (Operating) / -20 ~ 60°C (Storing)Humidity : 5% ~ 90% (Operating) / 5% ~ 95% (Storing)PhysicalSpecification50.8 x 29.9 x 3.2 mm (H x W x D)
Communications, Inc.Page 3Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) this device must accept any interference received, including interference thatmay cause undesired operation.Non-modification Statement:Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate theequipment.Validity of using the module certification:In the event that these conditions cannot be met (for example certain laptop configurations or co-location with anothertransmitter), then the FCC authorization for this module in combination with the host equipment is no longer consideredvalid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will beresponsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.Custom design antennas may be used, however the OEM installer must following the FCC 15.21 requirements and verify ifnew FCC approval will be necessary.End product labeling:This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may bemaintained between the antenna and users. The final end product must be labeled in a visible area with the following:“Contains FCC ID: NHPCLM30001300”.Information that must be placed in the end user manual:The OEM integrator has to be aware not to provide information to the end user regarding how to install orremove this RF module in the user's manual of the end product which integrates this module. The end
Communications, Inc.Page 4user manual shall include all required regulatory information/warning as show in this manual.Co-location warning:This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.OEM integration instructions:This device is intended only for OEM integrators under the following conditions:The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter modulemay not be co-located with any other transmitter or antenna. The module shall be only used with the external antenna(s)that has been originally tested and certified with this module.For all products market in US, OEM has to limit the operation channels in Channel 1 to Channel 11 or 3-9 as specifiedabove by the supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding toRegulatory Domain change.As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is stillresponsible for testing their end-product for any additional compliance requirements required with this module installed (forexample, digital device emissions, PC peripheral requirements, etc.).Important Notes:The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RFmodule in the user's manual of the end product which integrates this module. The end user manual shall include allrequired regulatory information/warning as show in this manual.

Navigation menu