Cameo Communications WLN1205 802.11n 2.0 draft Wireless LAN PCI Adapter User Manual M WLN 1205 OK

Download:
Mirror Download [FCC.gov]
Document ID	943566
Application ID	TJq8L2XELlCjb3hYbjOjfw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	67.46kB (843264 bits)
Date Submitted	2008-05-19 00:00:00
Date Available	2008-05-19 00:00:00
Creation Date	2008-04-17 14:06:49
Producing Software	AFPL Ghostscript 8.54
Document Lastmod	2008-05-16 16:04:50
Document Title	M-WLN-1205 _OK
Document Creator	PDFCreator Version 0.9.2
Document Author:	EmilyYang

802.11n 2.0 draft Wireless
LAN PCI Adapter
User’s Guide
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at
the factory to match the intended destination. The firmware setting is not accessible by the end user.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been
applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
EN 60 950-1: 2001 +A11: 2004
Safety of Information Technology Equipment
EN 50392: (2004-01)
Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human
exposure to electromagnetic fields (0 Hz - 300 GHz)
EN 300 328 V1.7.1: (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment
operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential
requirements under article 3.2 of the R&TTE Directive
EN 301 489-1 V1.6.1: (2005-09)
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 1: Common technical requirements
EN 301 489-17 V1.2.1 (2002-08)
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN
equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries,
except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device
for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10
mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum
authority in France.
0560
Česky
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími
příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse]
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.
Eesti
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment]
vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele
sätetele.
[Czech]
[Danish]
[Estonian]
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
English
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ
1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips]
atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiāijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
[Maltese]
ii
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek
és az 1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, Ŝe [nazwa wyrobu] jest zgodny z zasadniczymi wymogami
oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e
outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi
določili direktive 1999/5/ES.
Slovensky
[Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen
laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen
mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
iii
TABLE OF CONTENT
Introduction................................................................................................1
Overview of this User’s Guide .................................................................................1
Unpacking and Setup .................................................................................2
Unpacking .................................................................................................................2
Setup..........................................................................................................................2
IDentifying external components ...............................................................2
LED ...........................................................................................................................3
Check the installation................................................................................................3
Software Installation ..................................................................................4
Windows Based Utility Installation..........................................................................4
Wireless Utility Setting.............................................................................................5
I. Link Information ...........................................................................................6
II. Configuration..................................................................................................7
III. Site Survey ....................................................................................................10
V. WPS................................................................................................................12
VI. About .............................................................................................................14
Technical Specifications ........................................ 錯誤!
錯誤 尚未定義書籤。
尚未定義書籤。
iv
INTRODUCTION
Congratulations on your purchase of this 802.11n 2.0 draft Wireless LAN PCI
Adapter .
This manual contains detailed instructions regarding the operation of this product.
Please keep this manual for future reference.
With the 802.11n 2.0 draft Wireless LAN PCI Adapter , a desktop or laptop
computer can communicate with another computer wirelessly. An easy-to-use
utility is bundled with the Wireless USB Adapter for configuration, monitoring, and
diagnostic purposes.
The 802.11n 2.0 draft Wireless LAN PCI Adapter can wirelessly transmit and
receive data, at a speed of up to 54 megabits per second.
The 802.11n 2.0 draft Wireless LAN PCI Adapter provides users with access to
real-time information anywhere in their organization. The mobility of the 802.11n
2.0 draft Wireless LAN PCI Adapter provides productivity and service, which are
not available under wired networks. The 802.11n 2.0 draft Wireless LAN PCI
Adapter can easily adapt from peer-to-peer networks, suitable for a small number
of users, to full infrastructure networks of thousands of users that allow roaming
around a broad area.
Overview of this User’s Guide
Introduction. Describes the 802.11n 2.0 draft Wireless LAN PCI Adapter and its
features.
Unpacking and Setup. Helps you get started with the basic installation of the
802.11n 2.0 draft Wireless LAN PCI Adapter .
Hardware Installation. Describes the LED indicator on the Adapter.
Software Installation. Describes how to setup the driver and the utility setting.
Technical Specifications. Lists the technical (general, physical and environmental)
specifications of the 802.11n 2.0 draft Wireless LAN PCI Adapter .
UNPACKING AND SETUP
This section provides unpacking and setup information for the 802.11n 2.0 draft
Wireless LAN PCI Adapter
Unpacking
The box should contain the following items:
One 802.11n 2.0 draft Wireless LAN PCI Adapter
One Driver & Utility CD-ROM
If any item is found missing or damaged, please contact your local reseller for
replacement.
Setup
Before installation, check the following:
 Make sure your computer is running at least a 150 MHz or above processor
with 256MB RAM or above
 Visually inspect the PCI Adapter and make sure that it is fully plugged in to the
PCI slot.
 The operating system on your computer must be the following: Windows 2000
(Service Pack 4), XP (Service Pack 2), Windows Vista
 A draft 802.11n or 802.11b/g access point.
 Make sure the environment has minimal interference and obstructions.
IDENTIFYING EXTERNAL COMPONENTS
LED
When the LED is blinking, the WLAN Adapter is transmitting or receiving data on
the Wireless Ethernet network.
Check the installation
The LEDs of the Wireless LAN Adapter are clearly visible and the status of the
network link can be seen instantly:
1. Once the device is plugged to the station’s PCI slot, the LED of the Wireless
LAN Adapter will light up indicating a normal status.
2. When the device plugged to the station’s PCI slot and the driver was installed,
the ACT will start alternate blinking, it means that the device is starting to scan
the wireless devices near the Wireless LAN Adapter.
3. While the Wireless LAN Adapter linked up and transmitting data to the Access
Point or to other Wireless LAN station, the Link LED will lighted green.
SOFTWARE INSTALLATION
This section describes how to install the driver and utility for the 802.11n 2.0 draft
Wireless LAN PCI Adapter .
Windows Based Utility Installation
1) Insert the Utility and Driver CD-ROM into your computer’s CD-ROM Drive and
then click Install Utility.
2) Follow the InstallShield Wizard Instructions
3) Click Finish to restart the computer.
4) Plug the 802.11n 2.0 draft Wireless LAN PCI Adapter into an available PCI slot
on your computer
Wireless Utility Setting
The user can configure the wireless settings using the Wireless Adapter
Configuration Utility. Double-click the utility icon that appears in the taskbar.
The Wireless Adapter Configuration Utility is divided into six sections: Link Info,
Configuration, Site Survey, Profile, WPS and About.
I. Link Information
This is the default screen after launching the Utility program.
Status: Shows the associated BSSID, which can be used to identify the wireless
access point.
SSID: Shows the current SSID, which must be the same on the wireless client and
AP in order for communication to be established.
Frequency: Shows the current frequency used for the wireless network.
Wireless Mode: Shows the current wireless mode used for wireless communication.
Encryption: Shows the current encryption mode used on the wireless network.
TxRate: Shows the current data rate used for transmitting.
Channel: Shows the current channel for communication.
Link Quality: Shows the link quality of the 802.11n 2.0 draft Wireless LAN PCI
Adapter with the Access Point when operating under Infrastructure mode.
Signal Strength: Shows the wireless signal strength of the connection between the
802.11n 2.0 draft Wireless LAN PCI Adapter with the Access Point.
Data Rate: Shows the statistics of data transfer, and the calculation is based on the
number of packets transmitted and received.
Note: For FCC domain device, you can only select Channel 1~11
For ETSI domain device, you can only select Channel 1~13.
II. Configuration
This screen is where you set the basic wireless settings for the 802.11n 2.0 draft
Wireless LAN PCI Adapter
SSID: Service Set Identifier, which is a unique name shared among all clients in a
wireless network. The SSID must be identical for each client in the wireless
network.
Wireless Mode: There are two modes available for selection
● Infrastructure – to establish wireless communication with the LAN and other
wireless clients through the use of Access Points.
● Ad-Hoc – to establish point-to-point wireless communication directly with
other wireless client devices.
Authtication: The following options are available: Open System, Shared Key,
WPAPSK, WPA2-PSK, WPA EAP-TLS, WPA2 EPA-TLS and WPA2-PSK.
Select Open System, Shared Key for WEP data encryption feature.
Open or Shared Key
Open System and Shared Key require the user to set a WEP key to exchange
data with other wireless clients that have the same WEP key.
 Default Key: select one of the 4 keys to use.
 Network Key: choose the encryption way, either in HEX or ASCII formats,
and enter the password in the blank space.
 Key Length: select 64 or 128 bits as the length of the keys
Key Format: HEX or ASCII
If WPA/WPA2 is selected, configuration is enabled. Please click the
“configuration” button. The following window appears. Select the desired
Certification, select the desired Certification Authority and then enter the
Server/Domain name and Login Name
If WPA-PSK/WPA2-PSK is selected, click the “configuration” button. The
below window appears. Please enter a WPA Passphrase.
9
III. Site Survey
This screen allows the user to scan for available wireless networks (wireless clients
and Access Points). It also allows the user to establish wireless communications
with an available wireless network.
Available Network – displays the wireless networks (wireless clients and access
points) that are within range.
Select any one of the wireless networks by double-clicking on it or clicking on the
“Connect” button.
Click the “Refresh” button to scan for available networks.
10
IV. Profile
Profile – The user can create and manage the created profiles for home, work or
public areas. By double-clicking on one of the created profile, the setting will adjust
to the specific setting such as SSID, channel, and encryption as saved by that
particular profile.
Remove: Deletes the selected profile
Add: Adds a profile. The following screen will appear. The user can enter the
necessary information required for accessing Access Points or Wireless Router
Connect: The current connected profile information.
11
V. WPS
WiFi Protected Setup (WPS) is an optional certification program from the Wi-Fi
Alliance that is designed to ease the task of setting up and configuring security on a
wireless network. There are two methods used in the WPS as below instruction.
- Push the button on my access point To select the Push the button on my access point is for wireless client option.
There is a push button on the device or through a simulated button in the utility
12
- Enter a PIN into my access point To Enter a PIN is a mandatory method of setup for all WPS certified devices. If
you are using this method, you will need a Registrar Access Points or Wireless
Router to initiate the registration between the Wireless N PCI Adapter and
Access Points or Wireless Router. PIN No. is a random numeral.
Select one Registrar Access Points or Wireless Router.
13
VI. About
This screen displays information about the 802.11n 2.0 draft Wireless LAN PCI
Adapter , such as the Driver and Utility version. When a new version of the utility
becomes available for upgrade, users will be able to identify by version numbers.
14
TECHNICAL SPECIFICATIONS
General
Radio Technology
IEEE 802.11b Direct Sequence Spread Spectrum (DSSS)
IEEE 802.11g/IEEE 802.11n: Orthogonal Frequency Division Multiplexing
(OFDM)
Interface
PCI Adapter: 32-bit PCI bus
Data Transfer Rate
802.11b: 11Mbps, 5.5Mbps, 2Mbps, and 1Mbps
802.11g: 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps and
6Mbps
802.11n: up to 135 Mbps
Receiver Sensitivity
135Mbps: Typical -65dBm @ 10% PER (Packet Error Rate)
54Mbps: Typical -68dBm @ 10% PER (Packet Error Rate)
11Mbps: Typical -84dBm @ 8% PER (Packet Error Rate)
Transmit Power
17dBm
Frequency Range
2412 ~ 2484 MHz ISM band (channels 1 ~ 14)
2400~2483.5MHz ISM band (channels 1 ~ 11)
Modulation Schemes
DBPSK/DQPSK/CCK/OFDM
Channels
1~11 channels (FCC/NCC), 1~13 channels (ETSI)
Media Access Protocol
CSMA/CA with ACK
Security
64/128-bits WEP Encryption, WPA-PSK, WPA2-PSK, WPA, WPA2
Diagnostic LED
PCI Adapter: Link/Activity
Antenna
Two 1.8
SMA connector
2.0 dBi dipole antennas with R-SMA
connector
15
Physical and Environmental
Driver Support
Windows XP, Windows Vista
Temperature
Operating: 0° ~ 40° C, Storage: -10° ~ 70° C
Humidity
10% ~ 95% RH, no condensation
Dimensions
PCI Adapter:119.91x81x1.6 mm
Certifications
FCC Part 15.247 for US, ETS 300 328 for Europe,
16

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print
XMP Toolkit                     : 3.1-701
About                           : 7145a51e-0ea0-11dd-0000-3c105bbc198a
Producer                        : AFPL Ghostscript 8.54
Modify Date                     : 2008:05:16 16:04:50+08:00
Create Date                     : 2008:04:17 14:06:49+08:00
Creator Tool                    : PDFCreator Version 0.9.2
Metadata Date                   : 2008:05:16 16:04:50+08:00
Document ID                     : 7145a51e-0ea0-11dd-0000-3c105bbc198a
Instance ID                     : uuid:80752581-96d2-4daa-b700-e77d138a43eb
Format                          : application/pdf
Title                           : M-WLN-1205 _OK
Creator                         : EmilyYang
Has XFA                         : No
Page Count                      : 21
Author                          : EmilyYang

EXIF Metadata provided by EXIF.tools