Canon 162 WLAN Module User Manual User host manual 2

Download:
Mirror Download [FCC.gov]
Document ID	1238932
Application ID	rV4IBEbsKotK1o4NdiBWqA==
Document Description	User host manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	140.95kB (1761863 bits)
Date Submitted	2010-02-08 00:00:00
Date Available	2010-03-25 00:00:00
Creation Date	2009-12-17 19:54:56
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2009-12-18 10:41:08
Document Title	User host manual 2
Document Creator	FrameMaker 7.0

Linked Shooting
With linked shooting, up to 10 slave cameras can be linked in a wireless
network (via IEEE 802.11g in ad hoc mode) to the master camera on which
you will release the shutter. Any cameras compatible with linked shooting,
when they have WFT series transmitters attached, can be used as slave
cameras, regardless of model.
Note that there will be a slight delay after you release the master camera
shutter before the slave cameras shoot. Movie shooting is not supported.
Slave camera
Master camera
61
Setting Up Linked Shooting
First, establish a connection from the slave cameras to the master camera. Because linked
shooting utilizes a wireless connection via IEEE 802.11g in ad hoc mode, it is not available over
wired LANs.
Display the transmitter menu.
Select [Connection wizard].
Select [LinkedShot].
Set up the slave cameras.
On the camera, press the <7> button.
On the [7] tab, select [WFT settings] and press
<0>. [WFT settings] is added to the tab after
you attach the transmitter.
Select [Slave].
X The slave cameras are now ready, with the
following screen displayed.
When using multiple slave cameras, set up all
slave cameras to slave state.
Once the settings are complete, slaves cannot be
added or removed. You must repeat the setup
process from step 1.
62
Setting Up Linked Shooting
Set up the master camera.
At this point, switch to setting up the
slave cameras.
Check the number of slave cameras.
Establish the connection.
Configure the settings on the master camera
following steps 1-3 on the previous page, and then
select [Master].
X The following screen is displayed.
On the slave cameras, select [OK].
X On the master camera LCD monitor, the number of
slave cameras detected is displayed.
On the master camera and all slave cameras,
select [OK].
X A screen is displayed as the connection is tested.
The information you specified is stored on the
cameras. It is not stored on the transmitters.
63
Arranging the Slave Cameras
Slave camera
Slave camera
Slave camera
Slave camera
Master camera
Arrange the slave cameras in clear view of the master camera, without objects between
them.
You can arrange master camera in an overall circumference of up to approximately 100 m /
328 ft. However, the distance supported for linked shooting may be shorter depending on
the wireless communication conditions, which are affected by how the cameras are
arranged, the environment of use, and weather conditions.
Pressing the shutter button halfway on the master camera puts slave cameras in the same
state, as if the shutter buttons were pressed halfway. Similarly, fully pressing the shutter
button on the master camera has the same effect on slave cameras, which respond as if the
shutter buttons were fully pressed.
There will be a slight delay after you release the master camera shutter until the slave
camera shutters are released. (Simultaneous capture is not possible.)
During linked shooting, when you press the AE lock or depth-of-field preview button, the camera
focuses and meters as if you had pressed the shutter button halfway.
Once you have established a connection between the master camera and slave cameras, the
settings are retained even after you replace the batteries.
If you will no longer use a slave camera in linked shooting, set [Communication mode] to
[Disconnect] on that slave camera.
Any cameras compatible with linked shooting, when they have WFT series transmitters attached,
can be used as slave cameras, regardless of model.
64
Managing
Settings Information
65
Checking Settings
Check the network settings as follows.
In [WFT settings], select [Set up].
Select [Confirm settings].
X The settings are displayed.
Example of FTP transfer and wired LAN settings
66
Example of FTP transfer and wireless LAN settings
Changing Settings
Settings originally completed using the connection wizard can be changed as follows. You can
also change IP security settings (IPsec) not completed using the connection wizard, as well as
other settings, such as the setting that determines what happens if an image of the same file
name as an existing file is sent to the FTP server. (p.68)
In [WFT settings], select [Set up].
Select [LAN settings].
Select the settings number.
Select [Change].
Select the item to change.
Here, select the settings number that identifies the
LAN settings.
After selecting [Change settings name], you can
rename the settings.
Select the desired item from [LAN type], [TCP/IP],
[FTP server], or [Wireless LAN] and change the
setting.
67
Changing Settings
IP Security (IPsec)
Configured in [TCP/IP]  [Security].
IPsec is a set of standards for encrypted communication over the Internet. It provides effective
security for both wireless and wired LANs. To use this function, you must enable IPsec in the
network settings of your computer. When IPsec is employed, only transport mode is supported,
and DES encryption and SHA1 authentication are used. Note that the IP address of the
computer for communication with the transmitter must be entered in [Destination address] on
the settings screen.
Directory Structure of the Target Folder
Configured in [FTP server]  [Directory structure].
Selecting [Camera] automatically creates a folder structure matching that of the camera’s (such
as A/DCIM/100EOS1D) in the server’s root folder for image storage. If you have created a
subfolder in the root folder by changing the [Target folder] setting, a folder structure such as A/
DCIM/100EOS1D is automatically created in that folder for image storage.
Selecting [Default] will use the root folder for image storage. If you have created a subfolder in
the root folder by changing the [Target folder] setting, images are saved in that folder.
Overwriting Files of the Same Name
Configured in [FTP server]  [Overwrite same file].
When the transmitter is configured to prevent overwriting
If there is already a file of the same name in the target folder on the FTP server, the new file is
saved with an extension consisting of an underline and a number, as in IMG_0003_1.JPG.
When you resend images if initial transfer fails
Even if the transmitter is configured to overwrite files of the same name, if you resend an image
file that could not be transferred initially, the existing file may not be overwritten in some cases.
If this happens, the new file is saved with an extension consisting of an underline, a letter, and
a number, as in IMG_0003_a1.JPG.
Passive Mode
Configured in [FTP server]  [Passive mode].
Enable this setting in network environments protected by a firewall. If an Error 41 occurs
(“Cannot connect to FTP server”), setting passive mode to [Enable] may enable access to the
FTP server.
Preventing Changes to Settings
To prevent accidental changes to LAN settings, set [Protect
settings] to [On].
68
Saving and Loading Settings
Network settings can be saved on a memory card for use with other cameras.
Saving Settings
In [WFT settings], select [Set up].
Select [LAN settings].
Select the settings number.
Select [Change].
Select [Save settings].
Here, select the settings number that identifies the
LAN settings.
69
Saving and Loading Settings
Select [Save].
X The settings are now saved as a file on the
memory card.
The settings are saved as a file (WFTNPF**.NIF)
in the area of the memory card shown when the
card is opened (in the root directory).
The file name is determined automatically by the
camera: WFTNPF, followed by a number (01 to
99) and the extension NIF. You can rename the file
as desired by selecting [Change file name].
Loading Settings
Load settings files stored on a memory card as follows. Also use this procedure when loading
settings files created on a computer.
Make sure the settings file is saved in the folder shown when the memory card is opened (that
is, the root directory).
70
Select [Load settings].
Select the settings file.
Load the settings file.
X Select a settings file that matches your network
environment.
X Information from the settings file is loaded into the
selected settings number.
Using External Media
Commercially available external media, connected via USB, can be used
the same way as CF and SD cards. You can also back up images from CF
and SD cards onto external media.
Note that external media must meet the following requirements.
Use media conforming to the USB Mass Storage Class Specification.
If an external hard disk drive is used, use a self-powered drive. Buspowered drives do not work in some situations.
The main image storage area must be formatted with a FAT16 or
FAT32 file system.
Use media with a main image storage area of less than 1 TB
(terabyte), with 512 bytes per sector.
Do not use external media equipped with a card slot.
71
Connecting External Media
Before connecting external media to the transmitter, switch the camera’s power switch to
. Also turn off external media that has its own power supply.
When connecting external media, be sure to use the USB cable provided with the camera.
The transmitter USB port is not hot-pluggable. USB cables cannot be connected or
disconnected at any time. Follow the instructions in this section when connecting or
disconnecting USB cables.
72
Plug the external media into the USB
port.
In [WFT settings], select [USB device
connec.].
Select [Storage].
Select [Connect].
Open the port cover and connect the external
media.
Do not connect external media via a USB hub.
If the external media is self-powered, turn it on
after connecting it.
If you will not use a wireless or wired LAN at the
same time as the external media, set
[Communication mode] to [Disconnect].
Connecting External Media
Select [OK].
Camera operations such as shooting, menu
display, or image playback are not possible
until the connection is established.
When the transmitter is connected to the external
media, the transmitter’s  lamp is lit in green
and a message is displayed indicating that a
connection has been established.
When the confirmation message is displayed,
select [OK].
X At this point, the menu option [Disconnect]
becomes available. Select this option before
disconnecting the external media.
X After you exit the menu, the rear LCD panel
indicates that external media is connected.
External media cannot be formatted using the camera. Format it with a FAT16 or FAT32 file system
using the computer.
73
Connecting External Media
Unplugging External Media from the USB Port
Before unplugging external media from the USB port, always select [Disconnect] as shown in
step 5. Follow the instructions displayed to terminate the connection.
The connection will not be terminated if you simply turn off the camera and external media. If
you unplug external media while the connection is still active, plug the external media into the
USB port again and follow the preceding steps to terminate the connection.
Power Supply to External Media
External media is powered via the transmitter’s USB port as needed. However, external hard
disk drives may not work after connection in some cases.
Power Management
If you will not use a wireless or wired LAN at the
same time as the external media, set
[Communication mode] to [Disconnect]. The
camera battery drains faster under settings other
than [Disconnect] because power saving is
disabled.
Setting [Power saving] to [Enable] enables the
power supply to external media to be stopped
automatically, conserving the camera battery.
Power is supplied again automatically during
shooting, when captured images are stored.
Before shooting movie, set [Power saving] to [Disable] and make sure the transmitter’s  lamp
is lit in green. If you start shooting movie when the  lamp is out or blinking, the movie may not be
recorded to external media.
74
Choosing Recording Media When Shooting
Images can be stored on external media connected via USB just as on CF and SD cards.
You can also configure [Record func.], [Record/play], and [Folder] settings (described below)
to use the external media. For details, refer to the Camera Instruction Manual (page 56).
When recording movies to a hard disk, use a hard disk with fast write speeds.
On the [5] tab, select [Record
func+media/folder sel.].
X The icon for external media is displayed next to
icons for the CF and SD cards.
Complete the following settings, as needed. For
details on using [Record/play] with external
media, refer to the next page.
Although the  lamp will blink in green briefly if the camera is restarted or recovering from auto
power off, shooting is still possible. Any images captured at this time are stored temporarily in the
camera's internal memory and then recorded on external media when the  lamp remains lit in
green.
75
Choosing Recording Media When Shooting
[Record/play] Setting
When you select external media in [Record/play], the [Select location for DCIM folder]
screen is displayed. The DCIM folder contains the EOS1D folder, where images are stored.
To create the DCIM folder in the first folder
displayed when the external media is opened (that
is, the root directory), select the default setting of [/].
To create another parent folder for the DCIM
folder, select [Create folder]. A screen is
displayed for entering the folder name.
By default, the folder name comprises the current
date (last two digits of the year, in addition to the
month and day) and numbers representing the
order the folder was created, in a range of 01 to
99.
Always use 8 characters for the folder name.
For instructions on entering the folder name, refer to
“Virtual Keyboard Operation” (p.27).
76
Copying Images
Images can be copied to external media connected via USB just as to CF and SD cards.
On the [5] tab, select [Record
func+media/folder sel.].
Select the source media in [Record/
play].
On the [3] tab, select [Image copy].
X The icon for external media is displayed next to
icons for the CF and SD cards.
After selection, press the <7> button to return
to the menu screen.
For subsequent instructions, refer to the Camera
Instruction Manual (page 176). Operations are the
same as when using a CF or SD card, except that
the external media icon  is displayed.
77
Backing Up on External Media
Images stored on CF or SD cards can be backed up on external media.
Initially, captured images are stored in the DCIM folder on CF or SD cards. Selecting [External
media backup] backs up this DCIM folder to external media.
On the [3] tab, select [External media
backup].
Check the free space on the media.
Select the method of backup.
Make sure more space is available on the external
media than the amount used on the memory card.
If less free space is available on the external
media, backup is not possible.
Select [Quick backup] or [Backup].
You can also backup the MISC folder, where printing and transfer instructions are stored.
External media cannot be backed up onto memory cards.
If the backup destination already has a folder of the same number containing images of the same
number, [Skip image and continue], [Replace existing image], and [Cancel backup] are
displayed. Select the backup method and press <0>.
• [Skip image and continue]: All images are backed up except for images of the same number as
existing images
• [Replace existing image]: All images are backed up, including images of the same number as
existing images
Shooting is not possible during backup. Press [Cancel] before shooting.
78
Backing Up on External Media
\\\
Quick Backup
A simple method of backup is available, as follows.
Select [Quick backup].
Select the source memory card.
Select [Start].
Select [OK].
X The backup process now begins.
When the message indicating completion is
displayed, select [OK].
79
Backing Up on External Media
Where the DCIM Folder is Stored
The DCIM folder is stored in a directory indicated
by a file path such as [u/09103102/].
The target folder name comprises the current date
(last two digits of the year, in addition to the month
and day) and numbers representing the order the
folder was created, in a range of 01 to 99.
In the example shown at left, the folder displayed
when the external media is opened (that is, the
root directory) is named 09103102. The DCIM
folder is stored in this folder.
This is also the target folder name displayed when
using the regular [Backup] option.
Backup
Select regular [Backup] to create or use a folder of your choice as the parent folder of the
DCIM folder. You can also name this folder as desired. Other functions in this method of backup
are the same as for [Quick backup].
80
Select [Backup].
Select the source memory card.
Select [DCIM location].
Backing Up on External Media
Select [Create folder].
Enter the [Folder name].
Select [Start].
Select [OK].
Always use 8 characters for the folder name.
For instructions on entering the folder name, refer
to “Virtual Keyboard Operation” (p.27).
X The backup process now begins.
When the message indicating completion is
displayed, select [OK].
81
Backing Up on External Media
External Media Case
The provided external media case can hold portable hard disks up to 120 x 75 x 15 mm/
4.72 x 2.95 x 0.59 in.
82
Using GPS Devices
Commercially available GPS devices connected via USB can obtain
information including the latitude, longitude, altitude, and date and time of
shooting and add it to images. The additional information can be checked
on the camera as well as by using GPS-compatible mapping software.
The transmitter can be used with Garmin GPSMAP or eTrex series or
Magellan eXplorist series GPS devices that produce data in the format
NMEA 0183 Ver. 3.0.1, as well as some devices that produce Garmin
protocol data (as of November 2009).
For a list of specific GPS devices supported, contact the Canon Service
Center.
For GPS device instructions, refer to the device’s instruction manual or contact the
manufacturer.
83
Connecting GPS Devices with a USB Cable
Turn off the GPS device and camera before connecting them.
When connecting GPS devices, be sure to use the USB cable provided with the camera.
The transmitter USB port is not hot-pluggable. USB cables cannot be connected or
disconnected at any time. Follow the instructions in this section when connecting or
disconnecting USB cables.
84
Plug the GPS device into the USB port.
In [WFT settings], select [USB device
connec.].
Select [GPS].
Select [Connect].
Open the port cover and connect the GPS device.
Do not connect GPS device via a USB hub.
Do not turn the GPS device on until step 5.
If you will not use a wireless or wired LAN at the
same time as the GPS device, set
[Communication mode] to [Disconnect].
Connecting GPS Devices with a USB Cable
Select [OK].
After selecting [OK], turn the GPS device on.
It may take a few minutes to establish a connection
with the GPS device. Camera operations such as
shooting, menu display, or image playback are
not possible until the connection is established.
When the transmitter is connected to the GPS
device, the transmitter’s  lamp is lit in green
and a message is displayed indicating that a
connection has been established.
When the confirmation message is displayed,
select [OK].
X At this point, the menu option [Disconnect]
becomes available. Select this option before
disconnecting the GPS device.
Take the picture.
Check the GPS data.
Make sure the transmitter’s  lamp is lit in
green before shooting.
If the  lamp is not lit in green when you shoot,
correct GPS data will not be added to images.
View an image.
Press the <6> button to display the shooting
information screen with GPS data.
From top to bottom: latitude, longitude,
altitude, and Coordinated Universal Time
If the camera is turned off and on or recovering from auto power off, do not shoot until the  lamp remains
lit in green. If you shoot while the lamp is blinking, the correct GPS information may not be added to images.
The date and time indicated is the Coordinated Universal Time (UTC) as obtained by the GPS device,
which is nearly the same as Greenwich Mean Time (GMT). In some cases, the date and time of the
zone specified on the GPS device is indicated.
85
Connecting GPS Devices with a USB Cable
Unplugging GPS Devices from the USB Port
Before unplugging GPS devices from the USB port, always select [Disconnect] as shown in
step 5. Follow the instructions displayed to terminate the connection.
The connection will not be terminated if you simply turn off the camera and GPS device. If you
unplug GPS device while the connection is still active, plug the GPS device into the USB port
again and follow the preceding steps to terminate the connection.
Power Management
If you will not use a wireless or wired LAN at the
same time as the GPS device, set
[Communication mode] to [Disconnect]. The
camera battery drains faster under settings other
than [Disconnect] because power saving is
disabled.
86
Connecting GPS Devices via Bluetooth
By attaching the Canon Bluetooth Unit BU-30 to the USB port, you can connect Bluetooth®
GPS devices wirelessly. (Bluetooth® devices other than GPS devices cannot be connected).
When using non-Canon Bluetooth units, confirm normal operation before use.
Turn off the GPS device and camera before attaching the Bluetooth unit to the transmitter.
The transmitter’s USB port is not hot-pluggable. Bluetooth units cannot be connected or
disconnected indiscriminately. Follow the instructions in this section when attaching or
detaching Bluetooth units.
Attach the Bluetooth unit.
In [WFT settings], select [USB device
connec.]
Select [Bluetooth].
Select [Connect].
Open the port cover and attach the Bluetooth unit.
If you will not use a wireless or wired LAN at the
same time as the Bluetooth unit, set
[Communication mode] to [Disconnect].
87
Connecting GPS Devices via Bluetooth
Select [OK].
After the Bluetooth unit is attached to the
transmitter, the transmitter’s  lamp blinks in
green and a message is displayed indicating that a
connection has been established.
When the confirmation message is displayed, select [OK].
X At this point, the menu option [Disconnect]
becomes available. Select this option before
detaching the GPS device.
88
Establish a wireless connection between
the GPS device and Bluetooth unit.
Select the GPS device.
Turn on the GPS device and activate Bluetooth® on it.
Select [Bluetooth device connection].
X Nearby Bluetooth® devices in use are listed. (Only
GPS devices can be connected.)
Press <0> to display the connection status of
Bluetooth® devices.
Pressing <0> when the status is [Not conn.] will
list nearby Bluetooth® devices in use.
Turn the <5> dial to select [GPS] , and then
press <0>.
Select [OK] and press <0>.
If a Bluetooth® password has been set on the
GPS device, a password input screen is displayed.
Enter the password.
X The transmitter now starts to establish a
connection with the GPS device.
It may take a few minutes to establish a
connection with the GPS device.
Camera operations such as shooting, menu
display, or image playback are not possible
until the connection is established.
Connecting GPS Devices via Bluetooth
When the confirmation message is
displayed, select [OK].
Take the picture.
The GPS connection status changes to
[Connecting]. Pressing <0> under these
conditions will enable you to disconnect the GPS
device.
Make sure the transmitter’s  lamp is lit in
green before shooting.
If the  lamp is not lit in green when you
shoot, the correct GPS data will not be added
to images.
Check the GPS data.
10
View an image.
Press the <6> button to display the shooting
information screen with GPS data.
From top to bottom: latitude, longitude,
altitude, and Coordinated Universal Time
If the camera is turned off and on or recovering from auto power off, do not shoot until the  lamp
remains lit in green. If you shoot while the lamp is blinking, the correct GPS information may not be
added to images.
The date and time indicated is the Coordinated Universal Time (UTC) as obtained by the GPS device,
which is nearly the same as Greenwich Mean Time (GMT). In some cases, the date and time of the
zone specified on the GPS device is indicated.
89
Connecting GPS Devices via Bluetooth
Detaching Bluetooth units from the USB port
Before detaching Bluetooth units from the USB port, always select [Disconnect] as shown in
step 5. Follow the instructions displayed to terminate the connection.
The connection with the Bluetooth unit will not be terminated if you simply turn off the camera. If
you detach a Bluetooth unit while the connection is still active, attach the Bluetooth unit again
and follow the preceding steps to terminate the connection.
Power Management
If you will not use a wireless or wired LAN at the
same time as the Bluetooth unit, set
[Communication mode] to [Disconnect]. The
camera battery drains faster under settings other
than [Disconnect] because power saving is
disabled.
90
Troubleshooting
91
Responding to Error Messages
If transmitter errors are displayed on the camera LCD monitor, refer to the examples of
corrective actions in this section to eliminate the cause of the error. The error details can also
be checked on the [7] tab [WFT settings]  [Error description].
Click the error number in the following chart to jump to the corresponding page.
11 (p.93)
12 (p.93)
21 (p.93)
22 (p.94)
23 (p.94)
24 (p.95)
31 (p.97)
32 (p.97)
33 (p.97)
34 (p.97)
41 (p.98)
42 (p.99)
43 (p.99)
44 (p.99)
46 (p.100)
47 (p.101)
51 (p.101)
52 (p.101)
53 (p.101)
54 (p.101)
61 (p.102)
62 (p.102)
63 (p.103)
64 (p.103)
66 (p.104)
67 (p.104)
68 (p.104)
69 (p.104)
71 (p.105)
72 (p.105)
25 (p.96)
26 (p.96)
81 (p.105)
99 (p.105)
92
45 (p.100)
65 (p.103)
Responding to Error Messages
11: Connection target not found
Is the pairing software running?
X Start the pairing software and follow the instructions to re-establish the connection. (p.44)
Are the transmitter and wireless LAN terminal configured with the same encryption
key for authentication?
X This error occurs if the encryption keys do not match when the authentication method for
encryption is [Open system].
The setting is case-sensitive, so check upper- and lower-case characters. Make sure the
correct encryption key for authentication is entered on the transmitter. (p.22)
12: Connection target not found
Are the target computer and wireless LAN terminal on?
X Turn on the target computer and wireless LAN terminal.
21: No address assigned by DHCP server
What to check on the transmitter
On the transmitter, the network setting is [Auto setting] or the IP address setting is
[Auto assign]. Does the error occur under these settings?
X If no DHCP server is used, set the transmitter’s network setting to [Manual setting] and
IP address setting to [Manual setting]. (p.25)
What to check on the DHCP server
Is the DHCP server on?
X Turn the DHCP server on.
Are there enough addresses for assignment by the DHCP server?
X Increase the number of addresses assigned by the DHCP server.
X Remove devices assigned addresses by the DHCP server from the network to reduce the
number of addresses in use.
Is the DHCP server working correctly?
X Check the DHCP server settings to make sure it is working correctly as a DHCP server.
X If applicable, ask your network administrator to ensure the DHCP server is available.
Responding to Error Messages 21 - 26
Also check the following points when responding to errors numbered 21 - 26.
Are the transmitter and wireless LAN terminal configured with the same encryption key for
authentication?
X This error occurs if the encryption keys do not match when the authentication method for
encryption is [Open system]. The setting is case-sensitive, so check upper- and lower-case
characters. Make sure the correct encryption key for authentication is entered on the transmitter.
(p.22)
93
Responding to Error Messages
22: No response from DNS server
What to check on the transmitter
On the transmitter, the DNS address setting is [Auto assign] or [Manual setting].
Does the error occur under these settings?
X If no DNS server is used, set the transmitter’s DNS address setting to [Disable]. (p.25)
On the transmitter, does the DNS server’s IP address setting match the server’s
actual address?
X Configure the IP address on the transmitter to match the actual DNS server address.
(p.25, 107)
What to check on the DNS server
Is the DNS server on?
X Turn the DNS server on.
Are the DNS server settings for IP addresses and the corresponding names
correct?
X On the DNS server, make sure IP addresses and the corresponding names are entered
correctly.
Is the DNS server working correctly?
X Check the DNS server settings to make sure the server is working correctly as a DNS
server.
X If applicable, ask your network administrator to ensure the DNS server is available.
What to check on the network as a whole
Does your network include a router or similar device that serves as a gateway?
X If applicable, ask your network administrator for the network gateway address and enter it
on the transmitter. (p.25, 107)
X Make sure the gateway address setting is correctly entered on all network devices,
including the transmitter.
23: Duplicate IP address
What to check on the transmitter
Is another device on the transmitter network using the same IP address as the
transmitter?
X Change the transmitter’s IP address to avoid using the same address as another device
on the network. Otherwise, change the IP address of the device that has a duplicate
address.
X In network environments with a DHCP server, if the transmitter’s IP address setting is
[Manual setting], change it to [Auto assign]. (p.25)
94
Responding to Error Messages
24: No response from proxy server
What to check on the transmitter
The transmitter’s proxy server setting is [Enable]. Does the error occur under this
setting?
X If no proxy server is used, set the transmitter’s proxy server setting to [Disable]. (p.30)
Do the transmitter’s [Address setting] and [Port No.] settings match those of the
proxy server?
X Configure the transmitter’s proxy server address and port number to match those of the proxy
server. (p.30)
In the transmitter’s [Proxy server] settings, have you only entered [Server name]?
X If the proxy server’s [Address] setting is not configured on the transmitter, enter it along
with the DNS server address. (p.25) Make sure the server name and port number for the
proxy server are entered correctly. (p.30)
What to check on the proxy server
Is the proxy server on?
X Turn the proxy server on.
Is the proxy server working correctly?
X Check the proxy server settings to make sure the server is working correctly as a proxy
server.
X If applicable, ask your network administrator for the proxy server address or server name
and port number, and then enter them on the transmitter.
What to check on the network as a whole
Does your network include a router or similar device that serves as a gateway?
X If applicable, ask your network administrator for the network gateway address and enter it
on the transmitter.
X Make sure the gateway address setting is correctly entered on all network devices,
including the transmitter.
95
Responding to Error Messages
25: Another terminal has set the same IP address
Is another device on the transmitter network using the same IP address as the
transmitter?
X This error occurs if the transmitter is connected to a network where another device
subsequently connects with the same IP address. Change the transmitter’s IP address to
avoid using the same address as another device on the network. Otherwise, change the
IP address of the device that has a duplicate address.
26: No response from DHCP server
What to check on the transmitter
On the transmitter, the network setting is [Auto setting]. Does the error occur under
this setting?
X If no DHCP server is used, set the transmitter’s network setting to [Manual setting].
(p.25)
What to check on the DHCP server
Is the DHCP server on?
X Turn the DHCP server on.
Are the DHCP server settings for IP addresses and the corresponding names
correct?
X On the DHCP server, make sure IP addresses and the corresponding names are entered
correctly.
Is the DHCP server working correctly?
X Check the DHCP server settings to make sure it is working correctly as a DHCP server.
X If applicable, ask your network administrator to ensure the DHCP server is available.
What to check on the network as a whole
Does your network include a router or similar device that serves as a gateway?
X If applicable, ask your network administrator for the network gateway address and enter it
on the transmitter. (p.25)
X Make sure the gateway address setting is correctly entered on all network devices,
including the transmitter.
96
Responding to Error Messages
31: USB connection disconnected
Has the USB cable been disconnected?
X After connecting the USB cable, in [WFT settings], select [USB device connec.] and
reconnect the device.
Is the USB device on?
X Turn the USB device on. Next, also in [WFT settings], select [USB device connec.] and
reconnect the device.
32: Incompatible USB device
Have you connected a USB device other than external media, a GPS device, or a
Bluetooth unit?
X Connect only external media, GPS devices, or Bluetooth units.
The device is incompatible with the transmitter.
X External media with built-in card slots are not compatible. Similarly, USB card readers
cannot be used.
Is the external media formatted with a FAT16 or FAT32 file system?
X Format the external media with a FAT16 or FAT32 file system using the computer.
The GPS device is incompatible with the transmitter.
X Among GPS devices, we recommend devices for which operation has been verified by
Canon.
33: USB device error
There is a problem with the external media.
X Connect the external media to a computer and confirm that it is working correctly.
34: Cannot connect to USB device
Have you connected a USB device other than external media, a GPS device, or a
Bluetooth unit?
X Connect only external media, GPS devices, or Bluetooth units.
97
Responding to Error Messages
41: Cannot connect to FTP server
What to check on the transmitter
On the transmitter, does the FTP server’s IP address setting match the server’s
actual address?
X Configure the IP address on the transmitter to match the actual FTP server address.
(p.30)
Are the transmitter and wireless LAN terminal configured with the same encryption
key for authentication?
X This error occurs if the encryption keys do not match when the authentication method for
encryption is [Open system].
The setting is case-sensitive, so check upper- and lower-case characters. Make sure the
correct encryption key for authentication is entered on the transmitter. (p.22)
On the transmitter, does the [Port number setting] for the FTP server match the
actual port number of the FTP server?
X Configure the same port number (usually 21) on the transmitter and FTP server.
Configure the port number on the transmitter to match the actual FTP server port number.
(p.30)
If only the FTP server’s [Server name] is configured on the transmitter, are the DNS
server settings complete?
X If the FTP server’s [Address] setting is not configured on the transmitter, enable use of
the DNS server on the transmitter and enter its address. (p.25) Make sure the FTP server
name is entered correctly. (p.30)
What to check on the FTP server
Is the FTP server working correctly?
X Configure the computer correctly to function as an FTP server.
X If applicable, ask your network administrator for the FTP server address and port number,
and then enter them on the transmitter.
Is the FTP server on?
X Turn the FTP server on. The server may have been turned off because of an energysaving mode.
On the transmitter, does the FTP server’s IP address setting (in [Address]) match
the server’s actual address?
X Configure the IP address on the transmitter to match the actual FTP server address.
(p.30)
Is a firewall or other security software enabled?
X Some security software uses a firewall to restrict access to the FTP server. Change the
firewall settings to allow access to the FTP server.
X You may be able to access the FTP server by setting [Passive mode] to [Enable] on the
transmitter. (p.68)
98
Responding to Error Messages
Are you connecting to the FTP server via a broadband router?
X Some broadband routers use a firewall to restrict access to the FTP server. Change the
firewall settings to allow access to the FTP server.
X You may be able to access the FTP server by setting [Passive mode] to [Enable] on the
transmitter. (p.68)
If you are using Windows XP Service Pack 2 or later, is access to the FTP server
blocked by [Windows Firewall]?
X Change the Windows Firewall settings to allow access to the FTP server.
What to check on the network as a whole
Does your network include a router or similar device that serves as a gateway?
X If applicable, ask your network administrator for the network gateway address and enter it
on the transmitter. (p.25)
X Make sure the gateway address setting is correctly entered on all network devices,
including the transmitter.
42: FTP server rejected connection
What to check on the FTP server
Is the FTP server configured to restrict access to only some IP addresses?
X Change the FTP server settings to allow access from the [IP address] configured on the
transmitter in the TCP/IP settings.
43: Cannot connect to FTP server. Error code received from server.
What to check on the FTP server
Have you exceeded the maximum number of FTP server connections?
X Disconnect some network devices from the FTP server or increase the maximum number
of connections.
44: Cannot disconnect FTP server. Error code received from server.
This error occurs if the transmitter fails to disconnect from the FTP server for some
reason.
X Restart the FTP server and camera.
99
Responding to Error Messages
45: Cannot login to FTP server. Error code received from server.
What to check on the transmitter
On the transmitter, is the [Login name] entered correctly?
X Check the logon name for accessing the FTP server. The setting is case-sensitive, so
check upper- and lower-case characters. Make sure the correct logon name is entered on
the transmitter. (p.31)
On the transmitter, is the [Login password] entered correctly?
X If a logon password is configured on the FTP server, check the upper- and lower-case
characters to make sure the password on the transmitter matches it. (p.31)
What to check on the FTP server
Do the user rights for the FTP server allow reading, writing, and log access?
X Configure the FTP server’s user rights to allow reading, writing, and log access.
Is the folder specified as the transfer destination on the FTP server named with
ASCII characters (p.27)?
X Use ASCII characters for the folder name.
46: For the data session, error code received from FTP server
What to check on the FTP server
The connection was terminated by the FTP server.
X Restart the FTP server.
Do the user rights for the FTP server allow reading, writing, and log access?
X Configure the FTP server’s user rights to allow reading, writing, and log access.
Do user rights allow access to the target folder on the FTP server?
X Configure the user rights for access to the target folder on the FTP server to allow saving
images from the transmitter.
Is the FTP server on?
X Turn the FTP server on. The server may have been turned off because of an energysaving mode.
Is the hard disk of the FTP server full?
X Increase available space on the hard disk.
100
Responding to Error Messages
47: Image file transfer completion not confirmed by FTP server
This error occurs if, for some reason, the transmitter fails to receive confirmation
from the FTP server that image file transfer is complete.
X Restart the FTP server and camera and send the images again.
51: Connection with Bluetooth unit lost
Is the Bluetooth unit too far from the GPS device?
X Bring the GPS device closer to the Bluetooth unit.
Are any obstacles blocking the line of sight between the Bluetooth unit and the
GPS device?
X Move the GPS device to a position visible from the point of view of the Bluetooth unit.
The Bluetooth unit and GPS device were disconnected, for some reason, and the
connection cannot be restored.
X The connection is more likely to be lost if there are nearby wireless LAN terminals,
cordless telephones, microphones, microwave ovens, or similar devices operating on the
same 2.4 GHz band used for Bluetooth communication. Also note that the connection is
more likely to be lost in poor weather or high humidity.
Is the GPS device on?
X Turn the GPS device on.
52: Bluetooth unit not found
Is the GPS device ready for the Bluetooth connection?
X Turn the GPS device on and set it up for connection via Bluetooth.
Is the Bluetooth unit too far from the GPS device?
X Bring the GPS device closer to the Bluetooth unit.
Is the GPS device on?
X Turn the GPS device on.
53: Incorrect Bluetooth password
Is the same password set on the Bluetooth unit and GPS device?
X The setting is case-sensitive, so check upper- and lower-case characters. Make sure the
correct password is entered on the GPS device and Bluetooth unit.
54: No Bluetooth service
The GPS device does not support SPP (Serial Port Profile).
X Confirm that the GPS device supports SPP.
101
Responding to Error Messages
61: Same SSID wireless LAN terminal not found
Are any obstacles blocking the line of sight between the transmitter and the
antenna of the wireless LAN terminal?
X Move the antenna to a position clearly visible from the point of view of the transmitter.
(p.106)
What to check on the transmitter
On the transmitter, does the SSID setting match that of the wireless LAN terminal?
X Check the SSID on the wireless LAN terminal, and configure the same SSID on the
transmitter. (p.21)
What to check on the wireless LAN terminal
Is the wireless LAN terminal on?
X Turn on the wireless LAN terminal.
When you are using WFT-E2 IID with wireless LAN terminals supporting IEEE
802.11a, are the terminal settings locked on IEEE 802.11a?
X Configure the wireless LAN terminal to allow access via IEEE 802.11b and g.
If you are filtering by MAC address, did you register the transmitter’s MAC address
on the wireless LAN terminal?
X Register the transmitter’s MAC address (p.66) on the wireless LAN terminal.
62: No response from wireless LAN terminal
What to check on the transmitter
Is the transmitter configured for communication in infrastructure mode?
X Configure the transmitter for communication in ad hoc mode.
What to check on the wireless LAN terminal
Is there a nearby wireless LAN terminal for ad hoc communication?
X Prepare a wireless LAN terminal for ad hoc communication near the transmitter.
102
Responding to Error Messages
63: Wireless LAN authentication failed
Are the transmitter and wireless LAN terminal configured for the same
authentication method?
X The transmitter supports these authentication methods: [Open system], [Shared key],
[WPA-PSK], and [WPA2-PSK]. (p.21)
X When using an AirPort for communication in infrastructure mode, [Open system] is not
supported. Configure a [Shared key] on the transmitter. (p.21)
Are the transmitter and wireless LAN terminal configured with the same encryption
key for authentication?
X The setting is case-sensitive, so check upper- and lower-case characters. Make sure the
correct encryption key for authentication is entered on the transmitter and wireless LAN
terminal. (p.22)
If you are filtering by MAC address, did you register the transmitter’s MAC address
on the wireless LAN terminal?
X Register the transmitter’s MAC address (p.66) on the wireless LAN terminal.
64: Cannot connect to wireless LAN terminal
Are the transmitter and wireless LAN terminal configured for the same encryption
method?
X The transmitter supports these encryption methods: [WEP], [TKIP], and [AES]. (p.21)
If you are filtering by MAC address, did you register the transmitter’s MAC address
on the wireless LAN terminal?
X Register the transmitter’s MAC address (p.66) on the wireless LAN terminal.
65: Wireless LAN connection lost
Are any obstacles blocking the line of sight between the transmitter and the
antenna of the wireless LAN terminal?
X Move the antenna to a position clearly visible from the point of view of the transmitter.
(p.106)
The wireless LAN connection was lost, for some reason, and the connection
cannot be restored.
X The following are possible reasons: excessive access to the wireless LAN terminal from
other terminals, a microwave oven or similar appliance in use nearby (interfering with
IEEE 802.11b/g reception), poor weather and high humidity. (p.106)
103
Responding to Error Messages
66: Incorrect wireless LAN encryption key
Are the transmitter and wireless LAN terminal configured with the same encryption
key for authentication?
X The setting is case-sensitive, so check upper- and lower-case characters. Make sure the
correct encryption key for authentication is entered on the transmitter and wireless LAN
terminal. (p.22)
Note that if the authentication method is [Open system], an Error 41 (“Cannot connect to
FTP server”) is displayed.
67: Incorrect wireless LAN encryption method
Are the transmitter and wireless LAN terminal configured for the same encryption
method?
X The transmitter supports these encryption methods: [WEP], [TKIP], and [AES]. (p.21)
If you are filtering by MAC address, did you register the transmitter’s MAC address
on the wireless LAN terminal?
X Register the transmitter’s MAC address (p.66) on the wireless LAN terminal.
68: Cannot connect to wireless LAN terminal. Retry from the
beginning.
Have you pressed the Wi-Fi Protected Setup (WPS) button on the wireless LAN
terminal for as long as indicated in the wireless LAN terminal instructions?
X Refer to the instruction manual for the wireless LAN terminal to determine how long to
hold the WPS button.
Are you attempting to establish the connection near the wireless LAN terminal?
X Try establishing the connection when both devices are within reach of each other.
69: Multiple wireless LAN terminals have been found. Cannot
connect. Retry from the beginning.
Connection is in progress by other wireless LAN terminals in Pushbutton
Connection mode (PBC mode) of Wi-Fi Protected Setup (WPS).
X Wait a while before trying to establish the connection, or try to establish a connection in
PIN code connection mode (PIN mode). (p.24)
104
Responding to Error Messages
71: Cannot connect to slave cameras
Are you following the correct procedure to establish the connection with slave
cameras?
X Operate slave cameras by following the correct instructions (p.62, 63).
Are the slave cameras too far from the master camera?
X Bring the slave cameras closer to the master camera.
72: Cannot connect to the master camera
Are you following the correct procedure to establish the connection with master
camera?
X Operate the master camera by following the correct instructions (p.62, 63).
Is the master camera too far from the slave cameras?
X Bring the master camera closer to the slave cameras.
81: Wired LAN connection lost
Is the LAN cable securely connected?
X Reconnect the LAN cable between the transmitter and server. Because the cable may be
severed, try using another cable to connect the devices.
Is the hub or router on?
X Turn on the hub or router.
Is the server on?
X Turn the server on. The server may have been turned off because of an energy-saving
mode.
99: Other error
Another problem has occurred, identified with an error number other than 11 to 81.
X Turn the camera’s power switch off and on.
105
Wireless LAN Notes
When using the transmitter with a wireless LAN, try the following corrective actions if the
transmission rate drops, the connection is lost, or other problems occur.
Wireless LAN Terminal Installation and Antenna Position
When using the transmitter indoors, install the wireless LAN terminal in the same room
where you are shooting.
Install the wireless LAN terminal higher than the transmitter.
Install the device where people or objects do not come between it and the camera.
Install the device as close as possible to the camera. In particular, note that during
outdoor use in poor weather, rain may absorb radio waves and disrupt the connection.
Nearby Electronic Devices
If the transmission rate over a wireless LAN drops because of interference from the following
electronic devices, switching to a wired LAN can resolve the problem.
The transmitter communicates over wireless LANs via IEEE 802.11b/g and Bluetooth
using radio waves in the 2.4 GHz band. For this reason, the wireless LAN transmission
rate may drop if there are nearby microwave ovens, cordless telephones, microphones,
or similar devices operating on the same frequency band.
If a wireless LAN terminal on the same frequency band as the transmitter is used nearby,
the transmission rate of the wireless LAN may drop.
Using Multiple Transmitters
If multiple transmitters are connected to a single wireless LAN terminal, be careful not to
use duplicate camera IP addresses.
Note that the transmission rate drops when multiple transmitters access a single wireless
LAN terminal.
To reduce radio wave interference when there are multiple wireless IEEE 802.11b/g
devices, leave a gap of four channels between each wireless LAN channel. For example,
use channels 1, 6, and 11, channels 2, 7, and 12, or channels 3, 8, and 13.
When IEEE 802.11a can be used, switch to IEEE 802.11a and specify a different channel.
Security
Wireless LAN radio waves can be easily intercepted. For this reason, we recommend
activating encrypted communication in the wireless LAN terminal settings.
106
Checking Network Settings
Windows
Click the Windows [Start] button  [All Programs]  [Accessories]  [Command Prompt].
Type ipconfig/all and press the  key.
The IP address assigned to the computer is displayed, as well as the subnet mask, gateway,
and DNS server information.
To avoid using the same IP address for the computer and other devices on the network when
configuring the IP address assigned to the camera (page 25), change the rightmost numbers
here.
Macintosh
In Mac OS X, open the [Terminal] application, type ifconfig -a, and press the  key.
The IP address assigned to the computer is indicated in the [en0] item by [inet], in the format
***.***.***.***.
To avoid using the same IP address for the computer and other devices on the network when
configuring the IP address assigned to the camera (page 25), change the rightmost numbers
here.
* For information on the [Terminal] application, refer to the Mac OS X help.
107
108
Reference
109
Creating and Registering Captions
Follow these steps to create captions and register them on the camera, as introduced in
“Adding a Caption Before Transfer” (p.35). When creating and registering captions, use a
computer on which EOS Utility is installed.
Before you begin, attach the transmitter to the camera and use the USB cable provided
with the camera to connect the camera to the computer. For instructions on connecting the
camera to the computer with the USB cable and starting EOS Utility, refer to the Software
Instruction Manual (PDF) provided with the camera. Note that captions cannot be created for
cameras without an attached transmitter.
110
Start EOS Utility and select [Camera
settings/Remote shooting].
On the [
Enter the caption or captions.
Register the captions on the camera.
X The camera settings/remote
capture screen is displayed.
] tab, select [WFT Captions].
X The screen for caption creation is displayed.
To acquire caption data stored on the camera,
select [Load settings].
Enter up to 31 characters (in ASCII format).
Select [Apply to camera] to register your new
captions on the camera.
Specifications
Type
Type:
Image transfer accessory that can be used in wireless LANs and over
Ethernet in wired LANs (IPsec-compatible). Can be connected via USB
to external media, GPS devices, and Bluetooth units.
Wireless LAN
Standards compliance:
Transmission method:
Transmission range:
Transmission frequency:
(central frequency)
Connection method:
Security:
IEEE 802.11a (WFT-E2 IIA/B/C) and ARIB STD-T71
IEEE 802.11b and ARIB STD-T66
IEEE 802.11g and ARIB STD-T66
OFDM modulation (IEEE 802.11a/g)
DS-SS modulation (IEEE 802.11b)
Approx. 150 m / 492 ft.
* With no obstructions between the transmitting and receiving antennas
and no radio interference
* With a large, high-performance antenna attached to the wireless LAN
access point
WFT-E2 IIA: 5,180 - 5,320 MHz, channels 36 - 64
5,745 - 5,825 MHz, channels 149 - 165
2,412 - 2,462 MHz, channels 1 - 11
WFT-E2 IIB: 5,180 - 5,320 MHz, channels 36 - 64
5,500 - 5,700 MHz, channels 100 - 140
2,412 - 2,472 MHz, channels 1 - 13
WFT-E2 IIC: 5,745 - 5,805 MHz, channels 149 - 161
2,412 - 2,472 MHz, channels 1 - 13
WFT-E2 IID: 2,412 - 2,462 MHz, channels 1 - 11
Infrastructure or ad hoc mode
* Wi-Fi Protected Setup supported
Authentication method: Open, shared key, WPA-PSK, and WPA2-PSK
Encryption: WEP, TKIP, and AES
Wired LAN
Standards compliance:
IEEE 802.3u (Ethernet 10BASE-T and 100BASE-TX)
USB Connection
Connectable devices:
External media, GPS devices, and Bluetooth units
Interfaces
Camera:
Wired LAN:
External device:
Extension system terminal
Ethernet RJ-45 port
Hi-Speed USB port (for attaching external media, GPS devices, and
Bluetooth units)
111
Specifications
Image Capture Capacity
LAN
Wireless LAN
Wired LAN
At Normal Temperature
(23°C / 73°F)
1100
1200
Approx. number of images
At Low Temperature
(0°C / 32°F)
900
900
* Using a fully charged LP-E4
* Testing based on Camera & Imaging Products Association (CIPA)
standards
* Fewer images can be captured when transferring images over
wireless LAN.
* Fewer images can be captured when using bus-powered external
media or GPS devices.
Dimensions and Weight
Dimensions (W x H x D):
Weight:
26.0 x 97.7 x 31.8 mm / 1.0 x 3.8 x 1.3 in.
Approx. 85 g / 3.0 oz. (Body only)
Operating Environment
Temperature:
Humidity:
0°C - 45°C / 32°F - 113°F
85% or less
All preceding specifications are based on Canon testing standards.
Transmitter specifications and appearance are subject to change without notice
Model Number
WFT-E2 IIA
: DS585802
WFT-E2 IIB
: DS585801
WFT-E2 IIC
: DS585803
WFT-E2 IID
: DS585804
112
113
114
115
Statement on EC directive
Canon Inc. tímto prohlašuje, že tento CH9-1161 je ve shodČ se základními požadavky a dalšími pĜíslušnými
ustanoveními smČrnice 1999/5/ES.
Undertegnede Canon Inc. erklærer herved, at følgende udstyr CH9-1161 overholder de væsentlige krav og
øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt Canon Inc., dass sich das Gerät CH9-1161 in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Käesolevaga kinnitab Canon Inc. seadme CH9-1161 vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
Hereby, Canon Inc., declares that this CH9-1161 is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Por medio de la presente Canon Inc. declara que el CH9-1161 cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
ȂǼ ȉǾȃ ȆǹȇȅȊȈǹ Canon Inc. ¨ǾȁŸȃǼǿ ȅȉǿ CH9-1161 ȈȊȂȂȅȇĭŸȃǼȉǹǿ ȆȇȅȈ ȉǿȈ ȅȊȈǿŸ¨ǼǿȈ
ǹȆǹǿȉǾȈǼǿȈ Ȁǹǿ ȉǿȈ ȁȅǿȆǼȈ ȈȋǼȉǿȀǼȈ ¨ǿǹȉǹȄǼǿȈ ȉǾȈ ȅ¨ǾīǿǹȈ 1999/5/ǼȀ.
Par la présente Canon Inc. déclare que l'appareil CH9-1161 est conforme aux exigences essentielles et aux
autres dispositions pertinentes de la directive 1999/5/CE.
Con la presente Canon Inc. dichiara che questo CH9-1161 è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo Canon Inc. deklarƝ, ka CH9-1161 atbilst DirektƯvas 1999/5/EK bnjtiskajƗm prasƯbƗm un citiem ar to
saistƯtajiem noteikumiem.
Šiuo Canon Inc. deklaruoja, kad šis CH9-1161 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos
nuostatas.
Hierbij verklaart Canon Inc. dat het toestel CH9-1161 in overeenstemming is met de essentiële eisen en de
andere relevante bepalingen van richtlijn 1999/5/EG.
Hawnhekk, Canon Inc., jiddikjara li dan CH9-1161 jikkonforma mal-ƫtiƥijiet essenzjali u ma provvedimenti
oƫrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Alulírott, Canon Inc. nyilatkozom, hogy a CH9-1161 megfelel a vonatkozó alapvetõ követelményeknek és az
1999/5/EC irányelv egyéb elõírásainak.
Niniejszym Canon Inc. oĞwiadcza, Īe CH9-1161 jest zgodny z zasadniczymi wymogami oraz pozostaáymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Canon Inc. declara que este CH9-1161 está conforme com os requisitos essenciais e outras disposições da
Directiva 1999/5/CE.
Canon Inc. izjavlja, da je ta CH9-1161 v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloþili
direktive 1999/5/ES.
Canon Inc. týmto vyhlasuje, že CH9-1161 spĎĖa základné požiadavky a všetky príslušné ustanovenia
Smernice 1999/5/ES.
Canon Inc. vakuuttaa täten että CH9-1161 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar Canon Inc. att denna CH9-1161 står I överensstämmelse med de väsentliga egenskapskrav
och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Hér með lýsir Canon Inc. yfir því að CH9-1161 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru
í tilskipun 1999/5/EC.
Canon Inc. erklærer herved at utstyret CH9-1161 er i samsvar med de grunnleggende krav og øvrige
relevante krav i direktiv 1999/5/EF.
ɋ ɧɚɫɬɨɹɳɢɹ ɞɨɤɭɦɟɧɬ Canon Inc. ɞɟɤɥɚɪɢɪɚ, ɱɟ CH9-1161 ɟ ɜ ɫɴɝɥɚɫɢɟ ɫ ɨɫɧɨɜɧɢɬɟ ɢɡɢɫɤɜɚɧɢɹ ɢ
ɫɴɨɬɜɟɬɧɢɬɟ ɩɨɫɬɚɧɨɜɥɟɧɢɹ ɧɚ Ⱦɢɪɟɤɬɢɜɚ 1999/5/ȿɋ.
Prin prezenta, Canon Inc. declară că acest CH9-1161 este conform cu cerinĠele principale úi cu celelalte
prevederi relevante ale Directivei 1999/5/EC.
116
FCC / IC Notice
Model DS585802/DS585804 (including WLAN Module
Model CH9-1161,) FCC ID is 161)
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of this
device.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
The cable with the ferrite core provided with the digital camera must be used with this equipment
in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the
manual. If such changes or modifications should be made, you could be required to stop
operation of the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
The available scientific evidence does not show that any health problems are associated with
using low power wireless devices. There is no proof, however, that these low power wireless
devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency
energy (RF) in the microwave range while being used. Whereas high levels of RF can produce
health effects (by heating tissue), exposure to low-level RF that does not produce heating
effects causes no known adverse health effects. Many studies of low-level RF exposures have
not found any biological effects. Some studies have suggested that some biological effects
might occur, but such findings have not been con- firmed by additional research. DS585802/
DS585782/
DS585784
DS585804 has been tested and found to comply with FCC/IC radiation exposure limits set forth
for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
Canon U.S.A Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
This class B digital apparatus complies with Canadian ICES-003.
For body worn operation, this model has been tested and meets the FCC RF exposure
guidelines when used with the CANON INC. Cameras supplied or designated for this product.
Use of other Cameras may not ensure compliance with FCC RF exposure guidelines.
117
Index
Wireless and Wired
LAN Functions
Infrastructure......................................... 8, 21
IP address........................................... 25, 30
IPsec ......................................................... 68
Account ..................................................... 50
Ad hoc ................................................... 8, 21
Area of use .................................................. 8
Authentication...................................... 21, 68
Auto power off ........................................... 17
Batch transfer ................................ 36, 38, 39
Browser ..................................................... 52
Camera control.......................................... 55
Caption ...................................................... 35
Channel ....................................................... 8
Connection ................................................ 17
DHCP server ............................................. 25
DNS address ............................................. 25
DNS server................................................ 30
Encryption ........................................... 21, 68
Encryption key........................................... 22
EOS Utility ..................................... 13, 43, 47
EOSUtility .................................................. 18
Error .......................................................... 92
ESS-ID ...................................................... 21
File of same name..................................... 68
Folder .................................................. 31, 41
FTP server........................................... 13, 29
FTP trans................................................... 18
Gateway .................................................... 25
IEEE 802.11a .............................................. 8
IEEE 802.11b/g ........................................... 8
Image transfer ..................................... 13, 29
118
JPEG......................................................... 33
Key format................................................. 22
Keyboard................................................... 27
LAN cable ................................................. 20
Linked shooting......................................... 61
LinkedShot ................................................ 19
Login ......................................................... 31
Logon name .............................................. 50
MAC address ............................................ 44
Master camera .......................................... 63
Movie ............................................ 32, 54, 55
Network..................................................... 15
Open system............................................. 21
Pairing................................................. 26, 44
Passive mode ........................................... 68
Password .................................................. 50
PBC mode................................................. 23
PIN code connection mode....................... 24
PIN mode .................................................. 24
Port number .............................................. 30
Protect settings ......................................... 68
Proxy......................................................... 30
Pushbutton connection mode ................... 23
RAW.......................................................... 33
RAW+JPEG .............................................. 33
Remote capture .......... 13, 43, 49, 55, 58, 59
Router ....................................................... 25
Index
Select folder .............................................. 31
Settings information................................... 65
Shared key ................................................ 21
Simple control............................................ 58
Slave camera ............................................ 62
SSID .......................................................... 21
Stealth functions.................................. 23, 24
Storage...................................................... 41
Subnet mask ............................................. 25
Target ........................................................ 31
Target folder .............................................. 68
TKIP .......................................................... 21
Transfer after shooting .............................. 36
Transfer history ......................................... 40
Transfer with SET...................................... 34
Transferred images ................................... 41
Transferring images, automatic................. 32
Transferring images, individual images..... 34
Troubleshooting......................................... 91
URL ........................................................... 52
Viewing images ......................................... 53
Web ........................................................... 52
WEP .......................................................... 21
WFT Server ......................................... 13, 49
WFTserver................................................. 19
Wi-Fi Protected Setup ............................... 23
Wired LAN ................................................. 20
Wireless LAN specification.......................... 8
Wizard ....................................................... 17
WPA2-PSK................................................ 21
WPA-PSK.................................................. 21
WPS (Wi-Fi Protected Setup).............. 23, 24
Functions When
Connected via USB
Backup ................................................ 71, 80
Bluetooth................................................... 87
Bus-powered............................................. 71
Copying images ........................................ 77
Error .......................................................... 92
External media .............................. 13, 71, 75
GPS .......................................................... 83
GPS data .................................................. 85
GPS device ............................................... 13
Hard disk................................................... 71
Media ........................................................ 71
Power........................................................ 74
Power management............................ 74, 86
Quick backup ............................................ 79
Replace existing image............................. 78
Self-powered............................................. 71
Skip image and continue........................... 78
Troubleshooting ........................................ 91
USB connection ........................................ 71
Backing up images .................................... 78
119
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
U.S.A.
CANON U.S.A. INC.
One Canon Plaza, Lake Success, NY 11042-1198, U.S.A.
For all inquires concerning this product, call toll free in the U.S.
1-800-OK-CANON
CANADA
CANON CANADA INC. HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada
CANON CANADA INC. MONTREAL BRANCH
5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada
CANON CANADA INC. CALGARY OFFICE
2828, 16th Street, N.E. Calgary, Alberta T2E 7K7, Canada
For all inquiries concerning this product, call toll free in Canada
1-800-OK-CANON
EUROPE,
AFRICA &
MIDDLE EAST
CANON EUROPA N.V.
Bovenkerkerweg 59-61, 1185 XB Amstelveen, The Netherlands
CANON FRANCE S.A.S.
17,Quai du Président Paul Doumer, 92414 Courbevoie Cedex, France
CANON UK LTD.
Woodhatch Reigate, Surrey RH2 8BF, United Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano 8, 20097 San Donato Milanese, (MI), Italy
CANON Schweiz A.G.
Industriestrasse 12, 8305 Dietlikon, Switzerland
Canon GmbH
Zetschegasse 11, A-1230 Vienna, Austria
CANON España,S.A.
Av. De Europa,6 Alcobendas 28108 Madrid, Spain
CANON Portugal S.A.
Rua Alfredo da Silva,14 Alfragide 2610-016 Amadora, Portugal
CENTRAL &
SOUTH AMERICA
CANON LATIN AMERICA, INC.
703 Waterford Way, Suite 400 Miami, FL 33126, U.S.A.
ASIA
CANON (China) Co., LTD
15F Jinbao Building No.89 Jinbao Street, Dongcheng District, Beijing 100005, China
CANON HONGKONG CO., LTD.
19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue, #04-01 Keppel Bay Tower, Singapore 098632
CANON KOREA CONSUMER IMAGING INC.
Gangnam Finance Center 17F, 737,Yeoksam-Dong, Gangnam-Gu, Seoul, 135-984, Korea
OCEANIA
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, Sydney N.S.W. 2113, Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand
JAPAN
CANON MARKETING JAPAN INC.
16-6, Kohnan 2-chome, Minato-ku, Tokyo 108-8011, Japan
This instruction manual is current as of November 2009. For information on using the transmitter
with accessories introduced after this date, contact your nearest Canon Service Center.
CT1-7835aE-000
© CANON INC. 2009

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2009:12:17 19:54:56+09:00
Creator                         : FrameMaker 7.0
Modify Date                     : 2009:12:18 10:41:08+09:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2009:12:18 10:41:08+09:00
Creator Tool                    : FrameMaker 7.0
Format                          : application/pdf
Document ID                     : uuid:5ed962f9-9ca2-46f2-938a-d60689cb68ea
Instance ID                     : uuid:43c53526-4ef1-4849-ab61-251c52b2e9e9
Producer                        : Acrobat Distiller 6.0 (Windows)
Page Count                      : 60