Canon CH91108 802.11b/g WLAN Module User Manual
Canon Inc 802.11b/g WLAN Module
UserManual.wiki
>
Canon
>
CH91108 User Manual
>
User Manual
Contents
1.
User Manual
2.
User Manual 1 of 2
3.
User Manual 2 of 2
User Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![3Introduction These instructions should be followed only after your wireless or wired LAN and FTP server settings are complete. For details on configuring these settings, refer to the documentation provided with the respective equipment. Camera menu screens depicted in this manual are generally those of the EOS-1D Mark III. Terms in brackets [ ] indicate button or icon names or other software elements. Brackets also denote camera menu items. Page numbers in parentheses indicate where you can find additional information. Instructions on camera operations should be followed only after you have read the Camera Instruction Manual and are familiar with operating the camera. Sections of this manual labeled with the following symbols contain information of the corresponding nature.: Warnings to avoid potential problems are labeled with a caution symbol.: Supplemental information is labeled with a note symbol.Conventions Used in this Manual Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Macintosh is a registered trademark of Apple Corporation in the United States and other countries. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance. UPnP is a trademark of the UPnP Implementers Corporation. All other corporate and brand names in this manual are trademarks or registered trademarks of their respective owners.Using the transmitter for remote image transfer, capture, or viewing requires adequate knowledge ofconfiguring your wireless or wired LAN and FTP server.Canon cannot provide support for configuring wireless or wired LANs or FTP servers.Note that Canon cannot be held liable for any loss or damage to the transmitter from erroneous networkor FTP server settings. In addition, Canon cannot be held liable for any other loss or damage caused byuse of the transmitter.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-3.png)
![12This section describes the process of following the connection wizard instructions. If an error is displayed, refer to “Troubleshooting” in Chapter 8 (p.69) and check the settings. Pressing the shutter button or other camera controls during configuration by the connection wizard will close the connection wizard. Do not press the shutter button or other controls until configuration is finished. On the [5] tab, set [Auto power off] to [Off]. If auto power off is activated, the connection wizard will be closed during the configuration process.1Turn the camera on.2Display the transmitter menu. On the camera, press the <7> button. On the [7] tab, select [WFT settings] and press <0>. [WFT settings] is added to the tab after you attach the transmitter.3Select [Connection wizard].XThe [Select communication method] screen is displayed.XThe <LAN> lamp starts blinking.Displaying the Connection Wizard](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-12.png)
![131Basic Network Settings Turn the <5> dial to select the communication method, and then press <0>. Select [OK] and press <0> to go to the next screen.• FTPChoose this option to transfer captured images to an FTP server.Images can be automatically transferred as you shoot them, or you can select images for transfer later.Computer Operating SystemsOperation via [FTP] requires that Windows Vista (Business, Enterprise, or Ultimate Edition for 32- or 64-bit systems), Windows XP Professional, Windows 2000, or Mac OS X 10.4 be installed on your computer. In addition, the computer must be prepared as an FTP server in advance.For instructions on preparing your computer as an FTP server, refer to the computer documentation.Windows Vista Home Premium and Home Basic Edition as well as Windows XP Home Edition cannot be used because FTP server functionality is not supported.• PTPChoose this option when using EOS Utility for remote capture over a wireless or wired LAN.In addition to remote capture, all camera operations in EOS Utility are supported because a wireless or wired network is used with this option instead of the USB cable.Computer Operating SystemsOperation via [PTP] requires that any edition of Windows Vista for 32- or 64-bit systems (except Starter Edition), Windows XP (Home Edition or Professional, with Service Pack 2), or Mac OS X 10.4 be installed on your computer.• HTTPChoose this option for remote capture over a wireless or wired LAN.In addition, images on a memory card in the camera can be viewed and downloaded to a computer.The camera can be accessed like browsing a webpage, by users at up to three computers.Computer Operating SystemsAny computer with a web browser can be used, regardless of the operating system.Following the Connection WizardSelecting the Communication Method](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-13.png)
![14Following the Connection Wizard Turn the <5> dial to select the type of LAN, and then press <0>. Select [OK] and press <0> to go to the next screen.Wireless LANActive wireless LAN devices in your area are found and listed.Wired LANThe [Network] settings screen is displayed. If you have selected a wired network, refer to page 16, “Configuring Network Settings.” Use a Category 5 or higher STP LAN cable. (STP: Shielded Twisted Pair)Wireless LAN devices are listed with identifying information. Select the SSID (or ESS-ID) of your desired wireless LAN device. To select the wireless LAN device, press <0>. Turn the <5> dial to select the wireless LAN device, and then press <0>. Select [OK] and press <0> to go to the next screen.1Indicates whether the device is in infrastructure or ad hoc mode2An icon is displayed if the wireless LAN device is encrypting communication3Indicates the first 9 characters of the SSID4Indicates the channel usedEncryption by Wireless LAN DevicesIf the wireless LAN device is encrypting communication, select the corresponding method in [Authentication] and [Encryption]. [Authentication]: Open system, Shared key, WPA-PSK, or WPA2-PSK [Encryption]: WEP, TKIP, or AESSelecting the LAN TypeSelecting the Wireless Network123 4](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-14.png)
![151Following the Connection WizardBasic Network Settings[Enter connection] and [Search again] To configure settings for the wireless LAN device manually, select [Enter connection] and press <0>. Complete the settings for the items displayed, one after another. To search for wireless LAN devices again, select [Search again] and press <0>.Next, enter the encryption key of the wireless LAN device. For details on the encryption key, refer to the device’s instruction manual.Note that the screens displayed in steps 1 to 3 below vary depending on the authentication and encryption of the wireless LAN device.1 The [Key index] screen is displayed only if WEP encryption is used by the wireless LAN device. Turn the <5> dial to select the key index number specified as the access point, and then press <0>. Select [OK] and press <0> to go to the next screen.2 Turn the <5> dial to select the key format, and then press <0>. Select [OK] and press <0> to go to the next screen.3 Enter the encryption key. To switch between input areas, press the <H> button. To move the cursor, turn the <5> dial. In the bottom input area, turn the <5> dial and press <0> to enter the encryption key. If you make a mistake, press the <L> button to erase it. Press the <7> button to go to the next screen. To return to the previous screen, press the <6> button. The entry is erased.Entering the Wireless LAN Encryption Key](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-15.png)
![16Following the Connection Wizard Turn the <5> dial to select how to configure the network settings, and then press <0>. Select [OK] and press <0> to go to the next screen.[Auto setting] Settings otherwise configured with [Manual setting] can be configured automatically. However, the IP address and similar settings must be automatically assigned and configured in environments using DHCP servers or wireless LAN devices or routers supporting DHCP server functions.If an error is displayed, select [Manual setting] regardless of whether the IP address and similar settings are automatically assigned and configured.[Manual setting]The [IP address set.] screen is displayed after you select manual configuration. If [Auto setting] results in an error, enter the IP address manually. As the IP address, enter the IP address assigned to the camera.Enter the [IP address], [Subnet mask], [Gateway], and [DNS address] on each screen as they are displayed.If you are not sure what to enter, refer to page 84, “Checking Network Settings,” or ask the network administrator or another person knowledgeable about the network. When entering numbers for the IP address, subnet mask, and so on, press <0> to move the input position and turn the <5> dial to enter the number.Configuring Network Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-16.png)
![20These instructions are continued from Chapter 1.1 Turn the <5> dial to select [Address setting], and then press <0>.2 If you have set the DNS server setting to [Disable], the screen at left is displayed. Press <0> to select the input position, and then turn the <5> dial to enter the IP address of the FTP server. If you have set the DNS server IP address setting to [Auto assign] or [Manual setting], the screen at left is displayed. For instructions on screen operations, refer to “Virtual Keyboard Operation” (p.18). Enter the FTP server’s server name or IP address.3 In [Port No.], enter 00021, in most cases. Turn the <5> dial to select [OK], and then press <0> to go to the next screen.4 Complete the [Proxy server] settings. Turn the <5> dial to select [OK], and then press <0> to go to the next screen.Configuring FTP Transfer Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-20.png)
![21Configuring FTP Transfer Settings2FTP Settings and Image Transfer5 Complete the [Login method] settings. Turn the <5> dial to select [OK], and then press <0> to go to the next screen.6 Complete the [Target folder] settings. Select [Root folder] to have images saved in the root folder as specified in FTP server settings. (p.32) Select [Select folder] to specify a subfolder in the root folder. If no folder exists, a folder will be created automatically. Turn the <5> dial to select [OK], and then press <0> to connect to the FTP server.7 On the confirmation screen displayed next, select [OK] and press <0>.XThe <LAN> lamp is lit in green.8 Press <0>. Turn the <5> dial to select the set number, and then press <0>. Turn the <5> dial to select [OK], and then press <0>. After the connection wizard is closed, the display reverts to the menu screen. Settings information is stored on the camera. It is not stored on the transmitter.The FTP network settings are now complete.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-21.png)
![22An image can be automatically transferred to the FTP server immediately after shooting. You can also continue shooting even while images are being transferred.Before shooting, be sure to insert a memory card in the camera or connect external media (p.53). If you shoot without recording images, they cannot be transferred.1In [WFT settings], select [Set up].2Select [Automatic transfer]. Select [Enable].3Take the picture.XThe captured image is transferred to the FTP server. During image transfer, the <LAN> lamp blinks.Automatic Image Transfer After Each Shot During continuous shooting, images are transferred to the FTP server in the order they are captured. The captured images are also stored on the memory card. Any images for which transfer fails or is interrupted can transferred later together.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-22.png)
![23Automatic Image Transfer After Each Shot2FTP Settings and Image TransferWith automatic transfer, you can choose which images to transfer if images are stored on different memory cards depending on size, or if images of various types are recorded during RAW+JPEG shooting.1In [WFT settings], select [Set up].2Select [Transfer type/size].3Select the size and type of images to transfer. If the camera is set up to record larger JPEGs on a CF card and smaller JPEGs on an SD card and you want to transfer the smaller JPEGs, set [Larger/smaller JPEG] to [Smaller JPEG]. If the camera is set up to record RAW images on a CF card and JPEGs on an SD card, specify which images to transfer in the [RAW+JPEG transfer] setting. Similarly, complete the same setting if RAW+JPEG images are recorded simultaneously on a single memory card. If images of the same size are recorded on a CF card, SD card, and external media at the same time, images recorded on the CF card are transferred, regardless of the image quality (compression).Selecting Particular Sizes or Types of Images to Transfer](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-23.png)
![24Simply press <0> to transfer the currently displayed image. You can also add a caption before transferring images. You can also continue shooting even while images are being transferred.1In [WFT settings], select [Set up].2Select [Transfer with SET]. Select [Enable].3View the image. On the camera body, press the <x> button. Select the image to transfer, and then press <0> to transfer the image.Transferring Images IndividuallyTransferring the Current Image](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-24.png)
![25Transferring Images Individually2FTP Settings and Image TransferYou can add a registered caption to each image before transfer. This is effective if you want to inform the recipient the printing quantity, for example. The caption is also added to images stored on the camera.For instructions on creating and registering captions, refer to page 88.You can check for captions added to images by examining the Exif information, in the user comments.1Take the picture.2In [WFT settings], select [Transfer with caption].XThe last captured image is displayed. It is not possible to select other images on the [Transfer with caption] screen. To select another image for transfer with a caption, view that image before following these steps.3Select a caption. Turn the <5> dial to select the [Caption] frame, and then press <0>. Turn the <5> dial to select the content of the caption, and then press <0>.4Transfer the image. Turn the <5> dial to select [Transfer], and then press <0>.Adding a Caption Before TransferIf you add captions to images that include original decision data, these images are no longer judged to be original images.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-25.png)
![26After shooting, you can select multiple images as desired and transfer them all at once. You can also transfer unsent images or images that could not be sent previously.If both a CF card and SD card are in the camera, or if external media is connected, images are transferred from the source specified on the menu [5] tab, in [Record func+media/folder sel.] [Record/play].You can also continue shooting even while images are being transferred.1In [WFT settings], select [Image sel./transfer].2Select [Sel.Image].XAn image is displayed.3Select images to transfer. Press <0>. Turn the <5> dial to display <X> in the upper left corner of the image to transfer. Press <0> to confirm your selection.You can select up to 9,999 images. Press the <y> button to display three images per screen. Press the <u> button to display one image per screen again. After selecting images to transfer, press the <7> button.Batch Transfer Selecting Images to Transfer](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-26.png)
![27Batch Transfer2FTP Settings and Image Transfer4Transfer the images. Select [Transfer]. Select [OK] on the confirmation screen displayed next.XA transfer progress screen is displayed. During image transfer, the <LAN> lamp blinks.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-27.png)
![28Batch Transfer1In [WFT settings], select [Image sel./transfer].2Select [Sel.n].3Select [Folder images not transfer’d]. To transfer images that could not previously be transferred, select [Folder images failed transf.].4Select a folder.5Transfer the images. Select [Transfer]. Select [OK] on the confirmation screen displayed next.XA transfer progress screen is displayed. During image transfer, the <LAN> lamp blinks.Batch Transfer of Images in a FolderSelecting [Clear folder transf. history] will set the transfer history of images in the selected folder to “unsent.” This enables you to resend all the images in the folder later by selecting [Folder images not transfer’d].](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-28.png)
![29Batch Transfer2FTP Settings and Image Transfer1In [WFT settings], select [Image sel./transfer].2Select [All image].3Select [Card images not transferred]. To transfer images that could not previously be transferred, select [Card images failed transfer].4Transfer the images. Select [Transfer]. Select [OK] on the confirmation screen displayed next.XA transfer progress screen is displayed. During image transfer, the <LAN> lamp blinks.Batch Transfer of Images on Memory CardsSelecting [Clear card’s transf. history] will set the transfer history of images on the memory card to “unsent.” This enables you to resend all the images on the card later by selecting [Card images not transferred].](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-29.png)
![30Batch TransferYou can use the menu even during image transfer. However, to prevent transfer problems, some menu items are unavailable during transfer, including [WFT settings], [Protect images], [Erase images], and [Format].Menu Operation During Image Transfer](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-30.png)
![312FTP Settings and Image TransferTo check the transfer history, in [Image sel./transfer], select [Sel.Image].Image not selected for transfer (no icon)Image selected for transfer Image could not be transferredImage transferredOn the [Image sel./transfer] screen, you can check the number of images for transfer as well as the transfer history of images in the selected folder or memory card. Specifically, you can check the number of images classified as [Images failed trans.] and [Images transferred].Checking Image Transfer HistoryChecking the Transfer History of Individual ImagesChecking the Transfer History of Folders or Memory Cards](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-31.png)
![32Images transferred to the FTP server are stored in the following folder as specified in the FTP server settings. Under the default settings of the FTP server, images are stored in [C drive] [Inetpub] folder [ftproot] folder, or in a subfolder of this folder. If the root folder of the transfer destination has been changed in the FTP server settings, ask the FTP server administrator where images are transferred. Open the [Macintosh HD] [Users] folder. The folder where images are stored is located in the folder of the user currently logged on, or in a subfolder there.Under the default transmitter settings, transferred images will be stored in the root folder specified in the FTP server settings, in a folder structure such as A/DCIM/100EOS1D which is automatically created.Additionally, if you have selected a CF card as the media for recording and playback, a folder structure such as “A/DCIM/100EOS1D” is automatically created for image storage. For an SD card, “B/DCIM/100EOS1D” is created, and for external media, “C/DCIM/100EOS1D” is created. (CF card images are assigned to the A folder, SD card images to the B folder, and external media images to the C folder.) Viewing Transferred ImagesWindowsMacintoshFolders for Image Storage](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-32.png)
![34These instructions are continued from Chapter 1.You can use the included WFT Pairing Software to enable the transmitter to communicate with a computer via PTP.WFT Pairing Software is installed automatically during easy installation of the software provided with the camera. If it is not installed, install it on the computer for communication with the transmitter before this procedure.The configuration procedure is as follows, using Windows XP as an example.1 First, the pairing screen is displayed. Turn the <5> dial to select [OK]. When you press <0>, the following message is displayed. Here, ****** represents the last six digits of the MAC address of the WFT-E1 for the connection.2 Start the pairing software. Normally, it is installed in the same location as EOS Utility.XAfter the pairing software starts up, an icon is displayed in the task bar.XWhen the camera is detected, a message is displayed.Configuring PTP Transfer Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-34.png)
![35Configuring PTP Transfer Settings3PTP Settings and Remote Capture3 Double-click the pairing software icon.XDetected cameras are listed. Cameras that have already been connected are not included in the list. Click [Connect]. If multiple cameras are displayed, identify the camera to connect to by its [MAC address] or [IP address]. You can check the [MAC address] and [IP address] by accessing [Confirm settings] in the menu (p.48).4 When the camera detects the computer on which you clicked [Connect] in step 3, the message at left is displayed. Turn the <5> dial to select [OK], and then press <0>.5 Press <0>. Turn the <5> dial to select the set number, and then press <0>. After you turn the <5> dial to select [OK] and press <0>, the connection wizard is closed and EOS Utility starts up.XThe <LAN> lamp on the transmitter is lit in green. Settings information is stored on the camera. It is not stored on the transmitter.The PTP network settings are now complete.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-35.png)
![36Configuring PTP Transfer Settings There is no need to complete pairing again if you will continue using a particular camera, transmitter, and computer together after pairing without changing the settings.Before your next PTP session, simply turn on the camera to which the transmitter is attached and start the pairing software. The connection between the camera and computer will be established automatically. You can add the pairing software to the software launched at startup of your computer. In EOS Utility on the [Preferences] [Basic Settings] tab, select [ Add WFT Pairing Software to the Startup folder].](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-36.png)
![40These instructions are continued from Chapter 1. Press <0>. Turn the <5> dial to select the set number, and then press <0>. Turn the <5> dial to select [OK], and then press <0>. After the connection wizard is closed, the display reverts to the menu screen.XThe <LAN> lamp on the transmitter is lit in green. Settings information is stored on the camera. It is not stored on the transmitter.Enter a logon name and password for accessing the camera from a computer. The logon name and password you specify here are used on the computer when connecting to the camera.1 Turn the <5> dial to select [Set up], and then press <0>.2 Turn the <5> dial to select [HTTP account], and then press <0>.3 Select a user number. The camera can be accessed via HTTP from up to three computers. Here, select a user number to prevent conflicts when users at other computers are connected to the transmitter simultaneously. Turn the <5> dial to select [User *], and then press <0>.Configuring HTTP Transfer SettingsSetting up an Account](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-40.png)
![41Configuring HTTP Transfer Settings4HTTP Settings and Remote Capture4 After you select [Login name] and [Password], the following input screen is displayed. For instructions on input screen operations, refer to “Virtual Keyboard Operation” (p.18).The HTTP network settings are now complete.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-41.png)
![42In the web browser, display WFT Server, a screen for transmitter operations.Make sure you have already established a connection between the camera and computer.1Start the web browser. First, start Internet Explorer or another web browser.2Enter the URL. In the address field, enter the IP address assigned to the camera. Press the <Enter> key.XThe account screen is displayed. Enter the login name and password as specified in the procedure on page 41. Click [OK] to display the WFT Server screen. Select the language.Displaying WFT ServerIf you don’t know the URL (IP address)You can check the URL (IP address) by accessing [Confirm settings] in the menu (p.48).](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-42.png)
![434HTTP Settings and Remote Capture1Click [Capture].XThe capture screen is displayed.2Take the picture. Set the lens focus mode switch to <g> and adjust the focus. In the browser, click the release button of the simulated remote control. The camera will shoot when the button is released.XThe captured image is displayed in the simulated camera monitor in the browser. Captured images are stored on the memory card.Shooting Remotely](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-43.png)
![44Shooting Remotely3Download images to the computer. Click the image.XThe image is displayed at a larger size. Follow the web browser instructions to download the image to the computer. To return to the remote capture screen, click [Return].RAW images are not displayed, but they can be downloaded to the computer the same way as JPEGs.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-44.png)
![454HTTP Settings and Remote CaptureBrowse images on the camera’s memory card as follows.1Click [Viewer].XThe Viewer screen is displayed.2Select the memory card. If the camera is connected to external media, the corresponding icon is also displayed. Click the [DCIM] folder and select the folder where images are stored.3Select an image. To view another image, click the < > buttons or jump to other pages.Viewing Images](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-45.png)
![46Viewing Images4Download images to the computer. Click a thumbnail.XThe image is displayed at a larger size. Follow the web browser instructions to download the image to the computer. Click [Return] to return to the image viewing screen.RAW images are not displayed, but they can be downloaded to the computer the same way as JPEGs.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-46.png)
![48Check the network settings as follows.1In [WFT settings], select [Set up].2 Select [Confirm settings].XThe settings are displayed.Checking SettingsExample of FTP and wired LAN settingsExample of FTP and wireless LAN settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-48.png)
![495Managing Settings InformationSettings originally completed using the connection wizard can be changed as follows. You can also change IP security settings (IPsec) not completed using the connection wizard, as well as other settings, such as the setting that determines what happens if an image of the same file name as an existing file is sent to the FTP server. (p.50)1In [WFT settings], select [Set up].2Select [LAN settings].3Select the settings number. Here, select the settings number that identifies the LAN settings.4Select [Change]. After selecting [Change settings name], you can rename the settings.5Select the item to change. Select the desired item from [LAN type], [TCP/IP], [FTP server], or [Wireless LAN] and change the setting.Changing Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-49.png)
![50Changing SettingsConfigured in [TCP/IP] [Security].IPsec is a set of standards for encrypted communication over the Internet. It provides effective security for both wireless and wired LANs. To use this function, you must enable IPsec in the network settings of your computer. When IPsec is employed, only transport mode is supported, and DES encryption and SHA1 authentication are used. Note that the IP address of the computer for communication with the transmitter must be entered in [Destination address] on the settings screen.Configured in [FTP server] [Directory structure].Selecting [Camera] automatically creates a folder structure matching that of the camera’s (such as A/DCIM/100EOS1D) in the server’s root folder for image storage. If you have created a subfolder in the root folder by changing the [Target folder] setting, a folder structure such as A/DCIM/100EOS1D is automatically created in that folder for image storage.Selecting [Default] will use the root folder for image storage. If you have created a subfolder in the root folder by changing the [Target folder] setting, images are saved in that folder.Configured in [FTP server] [Overwrite same file].When the transmitter is configured to prevent overwritingIf there is already a file of the same name in the target folder on the FTP server, the new file is saved with an extension consisting of an underline and a number, as in GA5P0003_1.JPG.When you resend images if initial transfer failsEven if the transmitter is configured to overwrite files of the same name, if you resend an image file that could not be transferred initially, the existing file may not be overwritten in some cases. If this happens, the new file is saved with an extension consisting of an underline, a letter, and a number, as in GA5P0003_a1.JPG.Configured in [FTP server] [Passive mode].Enable this setting in network environments protected by a firewall. If an Error 41 occurs (“Cannot connect to FTP server”), setting passive mode to [Enable] may enable access to the FTP server.To prevent accidental changes to LAN settings, set [Protect settings] to [On].IP Security (IPsec)Directory Structure of the Target FolderOverwriting Files of the Same NamePassive ModePreventing Changes to Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-50.png)
![515Managing Settings InformationNetwork settings can be saved on a memory card for use with other cameras.1In [WFT settings], select [Set up].2Select [LAN settings].3Select the settings number. Here, select the settings number that identifies the LAN settings.4Select [Change].5Select [Save settings].Saving and Loading SettingsSaving Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-51.png)
![52Saving and Loading Settings6Select [Save].XThe settings are now saved as a file on the memory card. The file name is determined automatically by the camera: WFTNPF, followed by a number (01 to 99) and the extension NIF. You can rename the file as desired by selecting [Change file name].Load settings files stored on a memory card as follows. Also use this procedure when loading settings files created on a computer.Make sure the settings file is saved in the folder shown when the memory card is opened (that is, the root directory).1Select [Load settings].2Select the settings file.XSelect a settings file that matches your network environment.3Load the settings file.XInformation from the settings file is loaded into the selected settings number.Loading Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-52.png)
![54Before connecting external media to the transmitter, switch the camera power switch to <2>. Also turn off external media that has its own power supply.When connecting external media, be sure to use the USB cable provided with the camera.The transmitter USB port is not hot-pluggable. USB cables cannot be connected or disconnected at any time. Follow the instructions in this section when connecting or disconnecting USB cables.1Plug the external media into the USB port. Open the port cover and connect the external media. Do not connect external media via a USB hub. If the external media is self-powered, turn it on after connecting it.2In [WFT settings], select [USB device connec.]. If you will not use a wireless or wired LAN at the same time as the external media, set [Communication mode] to [Disconnect].3Select [Storage].4Select [Connect].Connecting External Media](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-54.png)
![55Connecting External Media6Using External Media5Select [OK]. Camera operations such as shooting, menu display, or image playback are not possible until the connection is established. When the transmitter is connected to the external media, the transmitter’s <USB> lamp is lit in green and a message is displayed indicating that a connection has been established. When the confirmation message is displayed, select [OK].XAt this point, the menu option [Disconnect] becomes available. Select this option before disconnecting the external media.XAfter you exit the menu, the camera’s rear LCD panel indicates that external media is connected.External media cannot be formatted using the camera. Format it with a FAT16 or FAT32 file system using the computer.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-55.png)
![56Connecting External MediaBefore unplugging external media from the USB port, always select [Disconnect] as shown in step 5. Follow the instructions displayed to terminate the connection.The connection will not be terminated if you simply turn off the camera and external media. If you unplug external media while the connection is still active, plug the external media into the USB port again and follow the preceding steps to terminate the connection.External media is powered via the transmitter’s USB port as needed. However, external hard disk drives may not work after connection in some cases.Power Management If you will not use a wireless or wired LAN at the same time as the external media, set [Communication mode] to [Disconnect]. The camera battery drains faster under settings other than [Disconnect] because power saving is disabled. Setting [Power saving] to [Enable] enables the power supply to external media to be stopped automatically, conserving the camera battery. Power is supplied again automatically during shooting, when captured images are stored.Unplugging External Media from the USB PortPower Supply to External Media](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-56.png)
![576Using External MediaImages can be stored on external media connected via USB just as on CF and SD cards.You can also configure [Record func.], [Record/play], and [Folder] settings (described below) to use the external media. For details, refer to the Camera Instruction Manual (page 73).On the [5] tab, select [Record func+media/folder sel.].XThe icon for external media is displayed next to icons for the CF and SD cards. Complete the following settings, as needed. For details on using [Record/play] with external media, refer to the next page.Choosing Recording Media When ShootingAlthough the <USB> lamp will blink in green briefly if the camera is restarted or recovering from autopower off, shooting is still possible. Any images captured at this time are stored temporarily in thecamera's internal memory and then recorded on external media when the <USB> lamp remains lit ingreen.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-57.png)
![58Choosing Recording Media When ShootingWhen you select external media in [Record/play], the [Select location for DCIM folder] screen is displayed. The DCIM folder contains the EOS1D folder, where images are stored. To create the DCIM folder in the first folder displayed when the external media is opened (that is, the root directory), select the default setting of [/]. To create another parent folder for the DCIM folder, select [Create folder]. A screen is displayed for entering the folder name. By default, the folder name comprises the current date (last two digits of the year, in addition to the month and day) and numbers representing the order the folder was created, in a range of 01 to 99. Always use 8 characters for the folder name.For instructions on entering the folder name, refer to “Virtual Keyboard Operation” (p.18).[Record/play] Setting](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-58.png)
![596Using External MediaImages can be copied to external media connected via USB just as to CF and SD cards.1On the [5] tab, select [Record func+media/folder sel.].XThe icon for external media is displayed next to icons for the CF and SD cards.2Select the source media in [Record/play]. After selection, press the <7> button to return to the menu screen.3On the [3] tab, select [Image copy]. For subsequent instructions, refer to the Camera Instruction Manual (page 125). Operations are the same as when using a CF or SD card, except that the external media icon <u> is displayed.Copying Images](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-59.png)
![60Images stored on CF or SD cards can be backed up on external media.Initially, captured images are stored in the DCIM folder on CF or SD cards. Selecting [External media backup] backs up this DCIM folder to external media.1On the [3] tab, select [External media backup].2Check the free space on the media. Make sure more space is available on the external media than the amount used on the memory card. If less free space is available on the external media, backup is not possible.3Select the method of backup. Select [Quick backup] or [Backup].Backing Up on External Media You can also backup the MISC folder, where printing and transfer instructions are stored. External media cannot be backed up onto memory cards. If the backup destination already has a folder of the same number containing images of the same number, [Skip image and continue], [Replace existing image], and [Cancel backup] are displayed. Select the backup method and press <0>.•[Skip image and continue]: All images are backed up except for images of the same number as existing images•[Replace existing image]: All images are backed up, including images of the same number as existing images Shooting is not possible during backup. Press [Cancel] before shooting.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-60.png)
![61Backing Up on External Media6Using External MediaA simple method of backup is available, as follows.1Select [Quick backup].2Select the source memory card.3Select [Start].4Select [OK].XThe backup process now begins. When the message indicating completion is displayed, select [OK].Quick Backup](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-61.png)
![62Backing Up on External MediaWhere the DCIM Folder is Stored The DCIM folder is stored in a directory indicated by a file path such as [u/07031902/]. The target folder name comprises the current date (last two digits of the year, in addition to the month and day) and numbers representing the order the folder was created, in a range of 01 to 99. In the example shown at left, the folder displayed when the external media is opened (that is, the root directory) is named 07031902. The DCIM folder is stored in this folder. This is also the target folder name displayed when using the regular [Backup] option.Select regular [Backup] to create or use a folder of your choice as the parent folder of the DCIM folder. You can also name this folder as desired. Other functions in this method of backup are the same as for [Quick backup].1Select [Backup].2Select the source memory card.3Select [DCIM location].Backup](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-62.png)
![63Backing Up on External Media6Using External Media4Select [Create folder].5Enter the [Folder name]. Always use 8 characters for the folder name. For instructions on entering the folder name, refer to “Virtual Keyboard Operation” (p.18).6Select [Start].7Select [OK].XThe backup process now begins.When the message indicating completion is displayed, select [OK].](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-63.png)
![66Turn off the GPS device and camera before connecting them.When connecting GPS devices, be sure to use the USB cable provided with the camera.The transmitter USB port is not hot-pluggable. USB cables cannot be connected or disconnected at any time. Follow the instructions in this section when connecting or disconnecting USB cables.1Plug the GPS device into the USB port. Open the port cover and connect the GPS device. Do not connect GPS device via a USB hub. Do not turn the GPS device on until step 5.2In [WFT settings], select [USB device connec.]. If you will not use a wireless or wired LAN at the same time as the GPS device, set [Communication mode] to [Disconnect].3Select [GPS].4Select [Connect].Connecting GPS Devices](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-66.png)
![67Connecting GPS Devices7Using GPS Devices5Select [OK]. After selecting [OK], turn the GPS device on. It may take a few minutes to establish a connection with the GPS device. Camera operations such as shooting, menu display, or image playback are not possible until the connection is established. When the transmitter is connected to the GPS device, the transmitter’s <USB> lamp is lit in green and a message is displayed indicating that a connection has been established. When the confirmation message is displayed, select [OK].XAt this point, the menu option [Disconnect] becomes available. Select this option before disconnecting the GPS device.6Take the picture. Make sure the transmitter’s <USB> lamp is lit in green before shooting. If the <USB> lamp is not lit in green when you shoot, correct GPS data will not be added to images.7Check the GPS data. View an image. Press the <6> button to display the shooting information screen with GPS data.From top to bottom: latitude, longitude, altitude, and Coordinated Universal TimeThe date and time indicated is the Coordinated Universal Time (UTC) as obtained by the GPS device, which is nearly the same as Greenwich Mean Time (GMT). In some cases, the date and time of the zone specified on the GPS device is indicated.If the camera is restarted or recovering from auto power off, do not shoot until the <USB> lamp remains lit in green. If you shoot while the lamp is blinking, the correct GPS information may not be added to images.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-67.png)
![68Connecting GPS DevicesBefore unplugging GPS devices from the USB port, always select [Disconnect] as shown in step 5. Follow the instructions displayed to terminate the connection.The connection will not be terminated if you simply turn off the camera and GPS device. If you unplug GPS device while the connection is still active, plug the GPS device into the USB port again and follow the preceding steps to terminate the connection. If you will not use a wireless or wired LAN at the same time as the GPS device, set [Communication mode] to [Disconnect]. The camera battery drains faster under settings other than [Disconnect] because power saving is disabled.Unplugging GPS Devices from the USB PortPower Management](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-68.png)
![71Responding to Error Messages8Troubleshooting Is the pairing software running?XStart the pairing software and follow the instructions to re-establish the connection. (p.34) Are the transmitter and wireless LAN device configured with the same encryption key for authentication?XThis error occurs if the encryption keys do not match when the authentication method for encryption is [Open system].The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct encryption key for authentication is entered on the transmitter. (p.15) Are the target computer and wireless LAN device on?XTurn on the target computer and wireless LAN device.What to check on the transmitter On the transmitter, the network setting is [Auto setting] or the IP address setting is [Auto assign]. Does the error occur under these settings?XIf no DHCP server is used, set the transmitter’s network setting to [Manual setting] and IP address setting to [Manual setting]. (p.16)What to check on the DHCP server Is the DHCP server on?XTurn the DHCP server on. Are there enough addresses for assignment by the DHCP server?XIncrease the number of addresses assigned by the DHCP server.XRemove devices assigned addresses by the DHCP server from the network to reduce the number of addresses in use. Is the DHCP server working correctly?XCheck the DHCP server settings to make sure it is working correctly as a DHCP server.XIf applicable, ask your network administrator to ensure the DHCP server is available.11: Connection target not found12: Connection target not found21: No address assigned by DHCP serverResponding to Error Messages 21 - 26Also check the following points when responding to errors numbered 21 - 26. Are the transmitter and wireless LAN device configured with the same encryption key for authentication? XThis error occurs if the encryption keys do not match when the authentication method for encryption is [Open system]. The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct encryption key for authentication is entered on the transmitter. (p.15)](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-71.png)
![72Responding to Error MessagesWhat to check on the transmitter On the transmitter, the DNS address setting is [Auto assign] or [Manual setting]. Does the error occur under these settings?XIf no DNS server is used, set the transmitter’s DNS address setting to [Disable]. (p.16) On the transmitter, does the DNS server’s IP address setting match the server’s actual address?XConfigure the IP address on the transmitter to match the actual DNS server address. (p.16, 84)What to check on the DNS server Is the DNS server on?XTurn the DNS server on. Are the DNS server settings for IP addresses and the corresponding names correct?XOn the DNS server, make sure IP addresses and the corresponding names are entered correctly. Is the DNS server working correctly?XCheck the DNS server settings to make sure the server is working correctly as a DNS server.XIf applicable, ask your network administrator to ensure the DNS server is available.What to check on the network as a whole Does your network include a router or similar device that serves as a gateway?XIf applicable, ask your network administrator for the network gateway address and enter it on the transmitter. (p.16, 84)XMake sure the gateway address setting is correctly entered on all network devices, including the transmitter.What to check on the transmitter Is another device on the transmitter network using the same IP address as the transmitter?XChange the transmitter’s IP address to avoid using the same address as another device on the network. Otherwise, change the IP address of the device that has a duplicate address.XIn network environments with a DHCP server, if the transmitter’s IP address setting is [Manual setting], change it to [Auto assign]. (p.16)22: No response from DNS server23: Duplicate IP address](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-72.png)
![73Responding to Error Messages8TroubleshootingWhat to check on the transmitter The transmitter’s proxy server setting is [Enable]. Does the error occur under this setting?XIf no proxy server is used, set the transmitter’s proxy server setting to [Disable]. (p.20) Do the transmitter’s [Address setting] and [Port No.] settings match those of the proxy server?XConfigure the transmitter’s proxy server address and port number to match those of the proxy server. (p.20) In the transmitter’s [Proxy server] settings, have you only entered [Server name]?XIf the proxy server’s [Address] setting is not configured on the transmitter, enter it along with the DNS server address. (p.16) Make sure the server name and port number for the proxy server are entered correctly. (p.20)What to check on the proxy server Is the proxy server on?XTurn the proxy server on. Is the proxy server working correctly?XCheck the proxy server settings to make sure the server is working correctly as a proxy server.XIf applicable, ask your network administrator for the proxy server address or server name and port number, and then enter them on the transmitter.What to check on the network as a whole Does your network include a router or similar device that serves as a gateway?XIf applicable, ask your network administrator for the network gateway address and enter it on the transmitter.XMake sure the gateway address setting is correctly entered on all network devices, including the transmitter.24: No response from proxy server](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-73.png)
![74Responding to Error Messages Is another device on the transmitter network using the same IP address as the transmitter?XThis error occurs if the transmitter is connected to a network where another device subsequently connects with the same IP address. Change the transmitter’s IP address to avoid using the same address as another device on the network. Otherwise, change the IP address of the device that has a duplicate address.What to check on the transmitter On the transmitter, the network setting is [Auto setting]. Does the error occur under this setting?XIf no DHCP server is used, set the transmitter’s network setting to [Manual setting]. (p.16)What to check on the DHCP server Is the DHCP server on?XTurn the DHCP server on. Are the DHCP server settings for IP addresses and the corresponding names correct?XOn the DHCP server, make sure IP addresses and the corresponding names are entered correctly. Is the DHCP server working correctly?XCheck the DHCP server settings to make sure it is working correctly as a DHCP server.XIf applicable, ask your network administrator to ensure the DHCP server is available.What to check on the network as a whole Does your network include a router or similar device that serves as a gateway?XIf applicable, ask your network administrator for the network gateway address and enter it on the transmitter. (p.16)XMake sure the gateway address setting is correctly entered on all network devices, including the transmitter.25: Another terminal has set the same IP address26: No response from DHCP server](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-74.png)
![75Responding to Error Messages8Troubleshooting Has the USB cable been disconnected?XAfter connecting the USB cable, in [WFT settings], select [USB device connec.] and reconnect the device. Is the USB device on?XTurn the USB device on. Next, also in [WFT settings], select [USB device connec.] and reconnect the device. Have you connected a USB device other than external media or a GPS device?XConnect only external media or a GPS device. The device is incompatible with the transmitter.XExternal media with built-in card slots are not compatible. Similarly, USB card readers cannot be used. Is the external media formatted with a FAT16 or FAT32 file system?XFormat the external media with a FAT16 or FAT32 file system using the computer. The GPS device is incompatible with the transmitter.XAmong GPS devices, we recommend devices for which operation has been verified by Canon. There is a problem with the external media.XConnect the external media to a computer and confirm that it is working correctly. Have you connected a USB device other than external media or a GPS device?XConnect only external media or a GPS device.31: USB connection disconnected32: Incompatible USB device33: USB device error34: Cannot connect to USB device](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-75.png)
![76Responding to Error MessagesWhat to check on the transmitter On the transmitter, does the FTP server’s IP address setting match the server’s actual address?XConfigure the IP address on the transmitter to match the actual FTP server address. (p.20) Are the transmitter and wireless LAN device configured with the same encryption key for authentication?XThis error occurs if the encryption keys do not match when the authentication method for encryption is [Open system].The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct encryption key for authentication is entered on the transmitter. (p.15) On the transmitter, does the [Port number setting] for the FTP server match the actual port number of the FTP server?XConfigure the same port number (usually 21) on the transmitter and FTP server. Configure the port number on the transmitter to match the actual FTP server port number. (p.20) If only the FTP server’s [Server name] is configured on the transmitter, are the DNS server settings complete?XIf the FTP server’s [Address] setting is not configured on the transmitter, enable use of the DNS server on the transmitter and enter its address. (p.16) Make sure the FTP server name is entered correctly. (p.20)What to check on the FTP server Is the FTP server working correctly?XConfigure the computer correctly to function as an FTP server.XIf applicable, ask your network administrator for the FTP server address and port number, and then enter them on the transmitter. Is the FTP server on?XTurn the FTP server on. The server may have been turned off because of an energy-saving mode. On the transmitter, does the FTP server’s IP address setting (in [Address]) match the server’s actual address?XConfigure the IP address on the transmitter to match the actual FTP server address. (p.20) Is a firewall or other security software enabled?XSome security software uses a firewall to restrict access to the FTP server. Change the firewall settings to allow access to the FTP server.XYou may be able to access the FTP server by setting [Passive mode] to [Enable] on the transmitter. (p.50)41: Cannot connect to FTP server](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-76.png)
![77Responding to Error Messages8Troubleshooting Are you connecting to the FTP server via a broadband router?XSome broadband routers use a firewall to restrict access to the FTP server. Change the firewall settings to allow access to the FTP server.XYou may be able to access the FTP server by setting [Passive mode] to [Enable] on the transmitter. (p.50) If you are using Windows XP Service Pack 2, is access to the FTP server blocked by the [Windows Firewall]?XChange the Windows Firewall settings to allow access to the FTP server.What to check on the network as a whole Does your network include a router or similar device that serves as a gateway?XIf applicable, ask your network administrator for the network gateway address and enter it on the transmitter. (p.16)XMake sure the gateway address setting is correctly entered on all network devices, including the transmitter.What to check on the FTP server Is the FTP server configured to restrict access to only some IP addresses?XChange the FTP server settings to allow access from the [IP address] configured on the transmitter in the TCP/IP settings.What to check on the FTP server Have you exceeded the maximum number of FTP server connections?XDisconnect some network devices from the FTP server or increase the maximum number of connections.42: FTP server rejected connection43: Cannot connect to FTP server. Error code received from server.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-77.png)
![78Responding to Error Messages This error occurs if the transmitter fails to disconnect from the FTP server for some reason.XRestart the FTP server and camera.What to check on the transmitter On the transmitter, is the [Login name] entered correctly?XCheck the logon name for accessing the FTP server. The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct logon name is entered on the transmitter. (p.21) On the transmitter, is the [Login password] entered correctly?XIf a logon password is configured on the FTP server, check the upper- and lower-case characters to make sure the password on the transmitter matches it. (p.21)What to check on the FTP server Do the user rights for the FTP server allow reading, writing, and log access?XConfigure the FTP server’s user rights to allow reading, writing, and log access.What to check on the FTP server The connection was terminated by the FTP server.XRestart the FTP server. Do the user rights for the FTP server allow reading, writing, and log access?XConfigure the FTP server’s user rights to allow reading, writing, and log access. Do user rights allow access to the target folder on the FTP server?XConfigure the user rights for access to the target folder on the FTP server to allow saving images from the transmitter. Is the FTP server on?XTurn the FTP server on. The server may have been turned off because of an energy-saving mode. Is the hard disk of the FTP server full?XIncrease available space on the hard disk.44: Cannot disconnect FTP server. Error code received from server. 45: Cannot login to FTP server. Error code received from server.46: For the data session, error code received from FTP server](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-78.png)
![80Responding to Error MessagesWhat to check on the transmitter Is the transmitter configured for communication in infrastructure mode?XConfigure the transmitter for communication in ad hoc mode.What to check on the wireless LAN device Is there a nearby wireless LAN device for ad hoc communication?XPrepare a wireless LAN device for ad hoc communication near the transmitter. Are the transmitter and wireless LAN device configured for the same authentication method?XThe transmitter supports these authentication methods: [Open system], [Shared key], [WPA-PSK], and [WPA2-PSK]. (p.14)XWhen using an AirPort for communication in infrastructure mode, [Open system] is not supported. Configure a [Shared key] on the transmitter. (p.14) Are the transmitter and wireless LAN device configured with the same encryption key for authentication?XThe setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct encryption key for authentication is entered on the transmitter and wireless LAN device. (p.15) If you are filtering by MAC address, did you register the transmitter’s MAC address on the wireless LAN device?XRegister the transmitter’s MAC address (p.48) on the wireless LAN device. Are the transmitter and wireless LAN device configured for the same encryption method?XThe transmitter supports these encryption methods: [WEP], [TKIP], and [AES]. (p.14) If you are filtering by MAC address, did you register the transmitter’s MAC address on the wireless LAN device?XRegister the transmitter’s MAC address (p.48) on the wireless LAN device.62: No response from wireless LAN terminal63: Wireless LAN authentication failed64: Cannot connect to wireless LAN terminal](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-80.png)
![81Responding to Error Messages8Troubleshooting Are any obstacles blocking the line of sight between the transmitter and the antenna of the wireless LAN device?XMove the antenna to a position clearly visible from the point of view of the transmitter. (p.83) The wireless LAN connection was lost, for some reason, and the connection cannot be restored.XThe following are possible reasons: excessive access to the wireless LAN device from other terminals, a microwave oven in use nearby, or poor weather. (p.83) Are the transmitter and wireless LAN device configured with the same encryption key for authentication?XThe setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct encryption key for authentication is entered on the transmitter and wireless LAN device. (p.15)Note that if the authentication method is [Open system], an Error 41 (“Cannot connect to FTP server”) is displayed. Are the transmitter and wireless LAN device configured for the same encryption method?XThe transmitter supports these encryption methods: [WEP], [TKIP], and [AES]. (p.14) If you are filtering by MAC address, did you register the transmitter’s MAC address on the wireless LAN device?XRegister the transmitter’s MAC address (p.48) on the wireless LAN device.65: Wireless LAN connection lost66: Incorrect wireless LAN encryption key67: Incorrect wireless LAN encryption method](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-81.png)
![84Click the Windows [Start] button [All Programs] [Accessories] [Command Prompt]. Type ipconfig/all and press the <Enter> key.The IP address assigned to the computer is displayed, as well as the subnet mask, gateway, and DNS server information.To avoid using the same IP address for the computer and other devices on the network when configuring the IP address assigned to the camera (page 16), change the rightmost numbers here.In Mac OS X, open the [Terminal] application, type ifconfig -a, and press the <Return> key. The IP address assigned to the computer is indicated in the [en0] item by [inet], in the format ***.***.***.***.To avoid using the same IP address for the computer and other devices on the network when configuring the IP address assigned to the camera (page 16), change the rightmost numbers here.* For information on the [Terminal] application, refer to the Mac OS X help.Checking Network SettingsWindowsMacintosh](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-84.png)
![86You can configure the wireless or wired LAN settings by using the software provided with the camera, WFT Utility. This is convenient if you want to create a wireless or wired LAN settings file when the camera and transmitter are not nearby.WFT Utility also enables you to create captions for attachment to images before transfer via FTP.Start WFT Utility from EOS Utility. In EOS Utility, access [Accessories] to start WFT Utility. Click the tabs for the transmitter’s [TCP/IP settings], [FTP settings], and [Wireless LAN settings] and complete the required settings for a wireless or wired LAN connection. Settings available here are the same as settings on the camera, with the addition of settings for creating captions.WFT Utility (Software)Starting WFT UtilityUsing Wireless or Wired LAN Settings](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-86.png)
![87WFT Utility (Software)9ReferenceWhen setting the wireless LAN channel on the [Wireless LAN settings] tab, first select [WFT-E2] or [WFT-E2A]. The WFT-E2 supports 13 channels, and the WFT-E2A, 11 channels.Keep in mind that the WFT-E2A cannot be used on channels 12 and 13 as the [WFT-E2] can. Settings files can be used as follows.Setting the Wireless LAN ChannelWireless or Wired LAN Settings FilesOpen Open a settings file saved on the computer or a memory card. SaveSave the settings file on the computer or a memory card. The [Settings name] is used as the file name.For instructions on applying a settings file on a memory card to the camera, refer to page ***. Apply settings to cameraApply the settings file to a camera. The camera and computer must be connected with the USB cable. Load settings from cameraLoad a settings file on the camera to the computer. The camera and computer must be connected with the USB cable.](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-87.png)
![88Follow these steps to create captions and register them on the camera, as introduced in “Adding a Caption Before Transfer” (p.25). When creating and registering captions, use a computer on which EOS Utility is installed.Before you begin, attach the transmitter to the camera and use the USB cable provided with the camera to connect the camera to the computer. For instructions on connecting the camera to the computer with the USB cable and starting EOS Utility, refer to the Software Instruction Manual (PDF) provided with the camera. Note that captions cannot be created for cameras without an attached transmitter.1Start EOS Utility and select [Camera settings/Remote shooting].XThe camera settings/remote capture screen is displayed.2On the [ ] tab, select [WFT Captions].XThe screen for caption creation is displayed. To acquire caption data stored on the camera, select [Load settings].3Enter the caption or captions. Enter up to 31 characters (in ASCII format).4Register the captions on the camera. Select [Apply to camera] to register your new captions on the camera.Creating and Registering Captions](https://usermanual.wiki/Canon/CH91108.User-Manual/User-Guide-762605-Page-88.png)
