Canon Imageformula Dr C125 Scanner Quick Reference Guide

2014-07-05

: Canon Canon-Imageformula-Dr-C125--Scanner-Quick-Reference-Guide canon-imageformula-dr-c125--scanner-quick-reference-guide canon pdf

Open the PDF directly: View PDF .
Page Count: 68

Reference Guide

• Please read this manual before operating this scanner.

• After you finish reading this manual, store it in a safe place for future

reference.

0-00-DR-C125_RG_UK.book Page 1 Thursday, September 8, 2011 6:03 PM

0-00-DR-C125_RG_UK.book Page 2 Thursday, September 8, 2011 6:03 PM

FCC REGULATIONS (For 120 V model)

Document Scanner, Model M111081

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with Class B limits in

Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless

otherwise specified in the manual. If such changes or modifications

should be made, you could be required to stop operation of the

equipment.

Canon U.S.A. Inc.

One Canon Plaza, Lake Success NY 11042, U.S.A.

Tel. No. (516)328-5000

RADIO INTERFERENCE REGULATIONS (For 120 V

models)

This digital apparatus does not exceed the Class B limits for radio

noise emissions from digital apparatus as set out in the interference-

causing equipment standard entitled “Digital Apparatus”, ICES-003 of

the Industry Canada.

RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE

(For 120 V models)

Cet appareil numérique respecte les limites de bruits radioélectriques

applicables aux appareils numériques de Classe B prescrites dans la

norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003

édictée par l’Industrie Canada.

International ENERGY STAR® Office Equipment Program

As an ENERGY STAR® Partner, CANON

ELECTRONICS INC. has determined that this

machine meets the ENERGY STAR® Program

guidelines for energy efficiency.

The International ENERGY STAR® Office Equipment

Program is an international program that promotes

energy saving through the use of computers and other office

equipment. The program backs the development and dissemination of

products with functions that effectively reduce energy consumption. It

is an open system in which business proprietors can participate

voluntarily. The targeted products are office equipment, such as

computers, monitors, printers, fax, machine, copiers, and scanners.

The standards and logos are uniform among participating nations.

European Union (and EEA) only.

This symbol indicates that this product is not to be disposed

of with your household waste, according to the WEEE

Directive (2002/96/EC) and your national law. This product

should be handed over to a designated collection point,

e.g., on an authorized one-for-one basis when you buy a

new similar product or to an authorized collection site for recycling

waste electrical and electronic equipment (EEE). Improper handling of

this type of waste could have a possible negative impact on the

environment and human health due to potentially hazardous

substances that are generally associated with EEE. At the same time,

your cooperation in the correct disposal of this product will contribute

to the effective usage of natural resources. For more information

about where you can drop off your waste equipment for recycling,

please contact your local city office, waste authority, approved WEEE

scheme or your household waste disposal service. For more

information regarding return and recycling of WEEE products, please

visit www.canon-europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

0-00-DR-C125_RG_UK.book Page 3 Thursday, September 8, 2011 6:03 PM

Für EMVG

Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und

Gewerbebereich sowie in Kleinbetrieben vorgesehen.

Model Names

The following names may be provided for the safety regulations in

each sales region of the Document Scanner.

DR-C125: Model M111081

Trademarks

• Canon and the Canon logo are registered trademarks, of Canon Inc.

in the United States and may also be trademarks or registered

trademarks in other countries.

• imageFORMULA is a trademark of CANON ELECTRONICS INC.

• Microsoft, Windows, Windows Vista, PowerPoint, and SharePoint

are registered trademarks or trademarks of Microsoft Corporation in

the United States and other countries.

• Microsoft product screen shot(s) reprinted with permission from

Microsoft Corporation.

• Macintosh and Mac OS are registered trademarks of Apple Inc. in

the United States and other countries.

• ENERGY STAR® is a registered trademark of the United States

Environmental Protection Agency.

• ISIS is a registered trademark of Emc Corporation in the United

States.

• Google and Google docs are trademarks of Google Inc.

reserved. Nuance, eCopy, OmniPage, and PaperPort are

trademarks and/or registered trademarks of Nuance

Communications, Inc. and/or its affiliates in the United States and/or

other countries.

• Other product and company names herein may be the trademarks

of their respective owners. However, the TM and ® symbols are not

used in this document.

No part of this publication may be reproduced or transmitted in any

form or by any means, electronic or mechanical, including

photocopying and recording, or by any information storage or retrieval

system without the prior written permission of CANON

ELECTRONICS INC.

Disclaimers

The information in this document is subject to change without notice.

CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY

KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR

IMPLIED, EXPECT AS PROVIDED HEREIN, INCLUDING WITHOUT

LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY,

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

OF USE OR NON-INFRINGEMENT. CANON ELECTRONICS INC.

SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.

CANON ELECTRONICS INC. IS NOT LIABLE FOR THE STORAGE

AND HANDLING OF DOCUMENTS SCANNED WITH THIS

PRODUCT, OR THE STORAGE AND HANDLING OF RESULTING

SCANNED IMAGE DATA.

IF YOU INTEND TO DISCARD THE ORIGINALS OF SCANNED

DOCUMENTS, YOU THE CUSTOMER ARE RESPONSIBLE FOR

INSPECTING THE SCANNED IMAGES AND VERIFYING THAT

DATA IS INTACT.

THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC.

UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE

OF THE PRODUCT COVERED BY THE WARRANTY.

0-00-DR-C125_RG_UK.book Page 4 Thursday, September 8, 2011 6:03 PM

Setup Guide

STEP 1 Checking the Accessories

If any of the items listed below are missing or damaged, contact your local authorized Canon dealer or service representative.

Scanner AC Adapter/Power Cord

(Connected length: 2.6 m)

Reference Guide

Setup DiscUSB Cable

Type A/Type B (Length: 1.8 m)

Warranty Card

(U.S.A. and Canada only)

Before Use

• Items included in this manual are subject to change without notice.

• You must keep the machine’s packaging and packing materials for storing or transporting the machine.

• A print version of Reference Guide is supplied in English.

The content of the Reference Guide can be found in other languages in the User Manual on the Setup Disc.

• The shape of the power plug varies by country and region.

Remove the scanner from the box, and remove the orange tape and protective sheets (▼) from the scanner.

Please read first.

0-00-DR-C125_RG_UK.book Page 5 Thursday, September 8, 2011 6:03 PM

Setup Disc Contents

Install the following software necessary for using the scanner from the

supplied Setup Disc.

• CaptureOnTouch

This is a dedicated scanning utility for this product.

• Scanner Driver

This is the scanner driver for this product.

Third-Party Software

The following software applications are also included on the supplied

Setup Disc.

• Presto! BizCard

Business card management software from NewSoft Technology

Corp. For Mac OS X, run the installer (BizCard/BCRInstaller) from

the Setup Disc to install.

* Presto! BizCard is a registered trademark of NewSoft Technology

Corp.

• OmniPage SE 4 (Windows only)

Optical character recognition (OCR) software from Nuance

Communications Inc. with multiple language support.

The languages supported by the OmniPage software bundled with

this scanner are English, French, German, Italian, and Spanish. The

software cannot be installed on operating systems of other

languages.

• PaperPort® (Windows only)

File management application from Nuance Communications Inc.

that makes it easy to store, organize, and retrieve digital documents.

– In order to receive support of this product, you need to upgrade to

a Professional version. For details on upgrading, visit the following

URL. http://www.nuance.com/partneroffer/canon

• eCopy PDF Pro Office (Windows only)

Nuance Communications PDF creation/editing software.

• Presto! PageManager (Mac OS X only)

Photo and document management software from NewSoft

Technology Corp. Run the following installer (PageManager/

PM8Installer) from the Setup Disc to install.

• Evernote

Multi-platform document filing software from Evernote Corp.

– Files required for installing this software must be downloaded via

the Internet. For details, refer to page 8 (Windows) or page 12

(Mac OS X).

– For more information on this software, visit the following URL:

http://www.evernote.com/about/intl/en/

IMPORTANT

When scanning with third-party software, user the scanner driver of

this scanner to configure scanning conditions. For details on how to

open the scanner driver, refer to the manuals supplied with each

software application.

Cloud Service Software

For some of the supplied third-party software, a cloud service account

is required to use some or all of their functions.

You will be asked to agree to terms of service when obtaining an

account. For details, refer to the website of your cloud service

provider.

Simple installation of the above software does not require an account.

Software Cloud service used

Google docs plug-in for

CaptureOnTouch Google docs

Evernote Evernote

0-00-DR-C125_RG_UK.book Page 6 Thursday, September 8, 2011 6:03 PM

Setup Guide

STEP 2 Installing the Software

System requirements

The following system requirements are recommended for optimal use

of this scanner.

Computer

CPU: Intel Core 2 Duo 1.66 GHz or faster

Memory: 1 GB or more

Hard disk: 3 GB or more available space required for

installation of all software

USB interface: Hi-Speed USB 2.0

Monitor: Resolution of 1024 x 768 (XGA) or better

recommended.

Optical drive: Drive capable of reading DVDs.

Operating system

• Microsoft Windows XP Service Pack 3 or later

• Microsoft Windows XP x64 Edition Service Pack 2 or later

• Microsoft Windows Vista Service Pack 2 or later (32-bit and 64-bit

editions)

• Microsoft Windows 7 Service Pack 1 or later (32-bit and 64-bit

editions)

• Mac OS X 10.5.8, 10.6.8, 10.7

Other requirement

• An ISIS-compatible application (Windows only) or a TWAIN-

compatible application that is compatible with the above operating

systems.

• .NET Framework 3.5 or later (Windows only)

IMPORTANT

• If you do not know the requirements for your computer system,

contact the store where you purchased the computer or the

manufacturer of the computer for more information.

• If you use the scanner with Windows, use the latest USB 2.0 driver

made available by Microsoft. For details, consult your local

authorized Canon dealer.

• Use the USB interface provided as standard with your computer.

However, normal operation is not guaranteed with all USB

interfaces, even if present as standard equipment on the computer.

For details, consult your local authorized Canon dealer.

• Scanning speeds are lower if your computer’s standard USB

interface is USB Full-Speed (equal to USB 1.1.)

• The USB cable you are using should be the one originally included

with the scanner.

• If the CPU, memory, interface card, and other specifications do not

satisfy the installation requirements, the scanning speed may be

greatly reduced and transmission may take a long time.

• Even if the computer satisfies the recommended specifications, the

scanning speed may vary, depending on the specified scan

settings.

• The scanner drivers provided with the scanner do not necessarily

operate on all ISIS (only for Windows) or TWAIN-compatible

applications. For details, contact your application software retailer.

Precautions for Use in 64-bit Operating Systems

• The scanner driver supplied with this product supports scanning

with 32bit applications only.

• Even with 32-bit applications, not all ISIS/TWAIN compliant

applications are guaranteed to operate.

• Scanning speed may vary depending on the specifications of your

computer.

Precautions for Use in Mac OS X

On a Macintosh computer equipped with a PowerPC CPU, the

scanner driver of this product cannot be used with Classic

Environment.

The driver will not run correctly when Classic Environment is running

so use the scanner when Classic Environment is not running.

0-00-DR-C125_RG_UK.book Page 7 Thursday, September 8, 2011 6:03 PM

Installing in Windows

IMPORTANT

• Install the software before connecting the scanner to the computer.

• Log on to Windows as an Administrator.

• Close all other applications before installing the software.

Insert the Setup Disc into the DVD drive of the computer.

The setup menu automatically starts up when you insert the disc

into the drive. (If the menu does not start up, execute setup.exe

from the disc.)

For Windows 7/Vista

If the [User Account Control] screen appears, click [Yes] or

[Allow].

Click [Typical Installation].

About Installation of Third-Party Software

If you select [Custom Installation], you can choose third-party

software applications for installation.

Hint

• If you choose Evernote, the Web browser will start and display

a webpage for downloading the software during the installation.

Download and install the software following the instructions on

the webpage.

To install Evernote, you need a connection to the Internet.

• If you want to reinstall only specific software that you have

previously uninstalled, select [Custom Installation] and specify

the software.

Click [Install].

0-00-DR-C125_RG_UK.book Page 8 Thursday, September 8, 2011 6:03 PM

Setup Guide

Click [Next].

Read the license agreement, and click [I accept the terms

in the license agreement] and then [Next] if you agree to

it.

Click [Install].

When the driver installation is complete, click [Finish].

Click [Next].

0-00-DR-C125_RG_UK.book Page 9 Thursday, September 8, 2011 6:03 PM

Read the license agreement, and click [Yes] if you agree

to it.

Click [Next].

Specify whether to install plug-in for Evernote, Microsoft

SharePoint and Google docs, and click [Next].

When CaptureOnTouch installation is complete, click

[Finish].

0-00-DR-C125_RG_UK.book Page 10 Thursday, September 8, 2011 6:03 PM

Setup Guide

Select the language you want to use, and click [Next].

When the User Manual installation is complete, click

[Finish].

Click [Exit] to finish installing the software.

Installing in Mac OS X

IMPORTANT

• Install the software before connecting the scanner to the computer.

• Close all other applications before installing the software.

Insert the Setup Disc into the DVD drive of the computer.

0-00-DR-C125_RG_UK.book Page 11 Thursday, September 8, 2011 6:03 PM

Click [DR-C125 Installer].

About Installation of Third-Party Software

If you open the folder containing the software instead of selecting

[DR-C125 Installer], you can choose third-party software

applications for installation.

Hint

If you choose Evernote, the Web browser will start and display a

webpage for downloading the software during the installation.

Download and install the software following the instructions on

the webpage.

To install Evernote, you need a connection to the Internet.

Click [Continue].

Read the license agreement and click [Continue] to

accept it.

Click [Agree].

0-00-DR-C125_RG_UK.book Page 12 Thursday, September 8, 2011 6:03 PM

Setup Guide

Click [Install].

Enter the user name and the password with administrator

privileges, and click [OK].

When the installation is complete, click [Close].

0-00-DR-C125_RG_UK.book Page 13 Thursday, September 8, 2011 6:03 PM

STEP 3 Connecting to a Computer

Connect the scanner to the computer and the power supply.

IMPORTANT

• Do not connect the scanner to the computer before installing the

software.

• Before connecting the scanner to the computer, verify that the

power of the scanner is OFF. If the power is ON, turn it OFF.

Hint

You can secure the cables to the back of the scanner. Make sure

there is sufficient slack in the cable when doing so to reduce stress

on the connector.

To the power outlet

AC adapter (included

with the scanner)

USB cable (included

with the scanner)

To computer

USB port

0-00-DR-C125_RG_UK.book Page 14 Thursday, September 8, 2011 6:03 PM

Setup Guide

STEP 4 Turning the Power ON

The power of the scanner can be turned ON and OFF with the power

button on the front of the scanner.

Make sure that the scanner and computer are connected

properly.

Press the power button.

The power button lights blue when the power turns ON.

Hint

In Windows, a balloon message such as shown below appears on the

task bar. If you wait a while, automatic scanner recognition will end

and the scanner will become ready to use.

When the scanner is properly connected to the computer, the

(CaptureOnTouch) icon appears on the taskbar (or menu bar) as

follows.

Windows taskbar

Mac OS X menu bar

If the taskbar icon appears as ( ), the scanner is not properly

connected to the computer. Check the status of the power switch and

USB cable.

Turning Off the Power

Press and hold the power button until the indicator goes out.

IMPORTANT

• After turning the scanner off, wait at least 10 seconds before turning

it back on.

• If you will not be using the scanner for an extended period, you

should disconnect the power cord from the AC outlet for safety.

Hint

The scanner’s auto power off setting is enabled by default, and the

scanner will turn off automatically if it is not operated for 4 hours.

For details on how to disable this setting, see “Auto Power Off Setting”

on p. 57.

Power button

This completes setup.

0-00-DR-C125_RG_UK.book Page 15 Thursday, September 8, 2011 6:03 PM

Introduction

Thank you for purchasing the Canon imageFORMULA DR-C125

Document Scanner.

Please read the following manuals carefully and familiarize yourself

with the functions of the scanner before use to ensure you sufficiently

understand the functions and make the most of the scanner’s

capabilities. After reading the manuals, store them in a safe place for

future reference.

Manuals for the Scanner

Documentation for this scanner consists of the following manuals.

●Reference Guide (this manual)

This describes setup procedures for the scanner. Read this manual

when you first use the scanner.

●User Manual

This manual contains complete explanations for operations on the

scanner. This manual is stored on the supplied Setup Disc as a PDF

electronic manual.

Hint

If you are using Windows, the User Manual will be registered to the

following location in the start menu after you install the software on the

Setup Disc.

Symbols Used in This Manual

The following symbols are used in this manual to explain procedures,

restrictions, handling precautions, and instructions that should be

observed for safety.

WARNING

Indicates a warning concerning operations that may lead to death

or injury to persons if not performed correctly. To use the scanner

safely, always pay attention to these warnings.

CAUTION

Indicates a caution concerning operations that may lead to injury to

persons, or damage to property if not performed correctly. To use

the scanner safely, always pay attention to these cautions.

IMPORTANT

Indicates operational requirements and restrictions. Be sure to

read these items carefully to operate the scanner correctly, and

avoid damaging the scanner.

Hint

Indicates a clarification of an operation, or contains additional

explanations for a procedure. Reading these notes is highly

recommended.

0-00-DR-C125_RG_UK.book Page 16 Thursday, September 8, 2011 6:03 PM

Table of Contents

Setup Guide ......................................................................... 5

Introduction ....................................................................... 16

Symbols Used in This Manual.................................................... 16

Important Safety Instructions.......................................... 18

Installation Location ................................................................... 18

AC Adapter................................................................................. 18

Moving the Scanner ................................................................... 19

Handling ..................................................................................... 19

Disposal ..................................................................................... 20

When sending the scanner for repairs ....................................... 20

Features of the Scanner................................................... 21

Names and Functions of Parts........................................ 23

Documents........................................................................ 25

How to Place Documents................................................. 27

Switching the Feed and Eject Methods ...................................... 27

Placing Documents for Standard Feeding ................................. 27

Placing Documents for Non Separation Feeding ....................... 30

Placing Cards............................................................................. 31

Scanning with CaptureOnTouch (Windows).................. 33

What is CaptureOnTouch?......................................................... 33

Starting and Exiting CaptureOnTouch ....................................... 33

Scan First ................................................................................... 34

Select Scan Job ......................................................................... 36

Scanning with Start Button ......................................................... 39

Scanner Settings ........................................................................ 39

Setting the Output Method ......................................................... 42

Scanning with CaptureOnTouch (Mac OS X)................. 43

What is CaptureOnTouch?......................................................... 43

Launching and Quitting CaptureOnTouch.................................. 43

Scan First ................................................................................... 44

Select Scan Job ......................................................................... 46

Scanning with Start Button ......................................................... 49

Scanner Settings ........................................................................ 49

Setting the Output Method ......................................................... 52

Daily Maintenance ............................................................ 53

Replacing Consumable Parts..................................................... 53

Auto Power Off Setting............................................................... 57

Common Problems and Solutions .................................. 59

Clearing a Paper Jam ....................................................... 61

Specifications ................................................................... 64

Replacement parts ..................................................................... 65

0-00-DR-C125_RG_UK.book Page 17 Thursday, September 8, 2011 6:03 PM

Important Safety Instructions

To ensure the safe operation of this scanner, be sure to read the

safety warnings and precautions described below.

Installation Location

The performance of this scanner is affected by the environment in

which it is installed. Make sure that the location where the scanner is

installed meets the following environmental requirements.

●Provide adequate space around the scanner for operation,

maintenance, and ventilation.

●When scanning documents using the straight path, provide

adequate space in front of the scanner for scanned document

output.

●Avoid installing the machine in direct sunlight. If this is unavoidable,

use curtains to shade the scanner.

●Avoid locations where a considerable amount of dust accumulates.

●Avoid warm or humid locations, such as in the vicinity of a water

faucet, water heater, or humidifier. Avoid locations where ammonia

gas is emitted. Avoid locations near volatile or flammable materials,

such as alcohol or paint thinner.

●Avoid locations that are subject to vibration.

●Avoid exposing the scanner to rapid changes in temperature. If the

room in which the scanner is installed is cold but rapidly heated,

water droplets (condensation) may form inside the scanner. This

may result in a noticeable degradation in scanning quality. The

following conditions are recommended for optimal scanning quality:

Room temperature: 10°C to 32.5°C (50°F to 90.5°F)

Humidity: 20% to 80% RH

●Avoid installing the scanner near equipment that generates a

magnetic field (e.g. speakers, televisions, or radios.)

AC Adapter

●Connect only to a power outlet of the rated voltage and power

supply frequency (120 V, 60 Hz or 220-240 V, 50/60 Hz depending

on your region).

●Do not connect other electrical equipment to the same power outlet

to which the scanner is connected. Also, when using an extension

cord, make sure that the extension cord is rated for the current

requirements of the scanner.

●Never try to take the AC adapter apart or modify it in any way, as

this is dangerous.

●The power cord may become damaged if it is often stepped on or if

heavy objects are placed on it.

●Do not use the power cord while it is coiled.

●Do not pull directly on the power cord. When disconnecting the

power cord, grasp the plug and remove it from the outlet.

●Keep the area around the power cord clear of objects so that the

power cord can be disconnected easily in an emergency.

●Do not use an AC adapter other than the one provided with the

scanner. Do not use the AC adapter provided with the scanner with

other products.

●If you have any questions regarding the power supply, contact your

local authorized Canon dealer or service representative for further

information.

100 mm

(3.94")

100 mm

(3.94")

100 mm

(3.94")

0-00-DR-C125_RG_UK.book Page 18 Thursday, September 8, 2011 6:03 PM

Moving the Scanner

●When moving the scanner, always hold it with both hands to avoid

dropping it. The scanner weighs approximately 2.6 kg (5.73 lb).

●Make sure to disconnect the interface cable and AC adapter before

moving the scanner. If the scanner is transported with these items

connected, the plugs and connectors may be damaged.

Handling

WARNING

Note the following precautions whenever using the scanner. Failure to

do so may result in a fire or electric shock.

●Never use alcohol, benzene, paint thinner, aerosol sprays, or any

other highly flammable substance near the scanner.

●Do not cut, damage, or modify the power cord. Do not place heavy

objects on the power cord, and do not pull or excessively bend the

power cord.

●Never connect the power cord when your hands are wet.

●Do not connect the scanner to a multi plug power strip.

●Do not knot or coil the power cord as this may result in a fire or

electric shock. When connecting the power cord, make sure that the

power plug is securely and completely inserted into the power

outlet.

●Do not use a power cord or AC adapter other than the ones

provided with this scanner.

●Do not take the scanner apart or modify it.

●Never try to take the AC adapter apart or modify it in any way, as

this is dangerous.

●Do not use flammable spray near the scanner.

●When cleaning the scanner, push the power button to turn it OFF

and disconnect the power cord from the power supply.

●Clean the scanner using a slightly dampened cloth which has been

well wrung out. Never use alcohol, benzene, paint thinner, or any

other flammable substances.

●If the scanner makes strange noises, or gives off smoke, heat, or

strange odors, or the scanner does not function or other

abnormalities occur when you use the machine, immediately push

the power button to turn it off, and disconnect the power plug from

the power outlet. Then, contact your local authorized Canon dealer

or service representative to have the unit serviced.

●Do not drop the scanner, or subject it to impact or strong shock.

Should the scanner ever become damaged, immediately push the

power button to turn it OFF, and disconnect the power plug from the

power outlet. Then, contact your local authorized Canon dealer or

service representative to have the unit serviced.

●Before moving the scanner, be sure to push the power button to turn

it OFF, and disconnect the power plug from the power outlet

CAUTION

●Do not install the scanner on a surface that is unstable or tilted, or

in an area subject to excessive vibrations, as this may cause the

scanner to fall, resulting in personal injury or damage to the

scanner.

●Never place small metal objects such as staples, paper clips, or

jewelry on the scanner. These items may fall into the scanner, and

cause a fire or electric shock. Should such objects ever fall inside

the scanner, immediately push the power button to turn it OFF, and

disconnect the power plug from the power outlet. Then, contact

your local authorized Canon dealer or service representative to

have the unit serviced.

●Do not install the scanner in a humid or dusty location. Doing so

might cause a fire or electric shock.

●Do not place objects on top of the scanner. Such objects may tip or

fall over, resulting in personal injury.

●Connect only to a power outlet of the rated voltage and power

supply frequency (120 V, 60 Hz or 220-240 V, 50/60 Hz depending

on your region).

●When unplugging the power cord, grasp it firmly by its plug. Do not

pull directly on the power cord, as this may damage or expose the

cord’s internal wiring, resulting in a fire or electric shock.

●Leave sufficient space around the power plug so that it can be

unplugged easily. If objects are placed around the power plug, you

will be unable to unplug it in an emergency.

0-00-DR-C125_RG_UK.book Page 19 Thursday, September 8, 2011 6:03 PM

●Do not allow water or flammable substances (alcohol, paint thinner,

benzene, etc.) to spill into the scanner, as this may result in a fire or

electric shock.

●Push the power button to turn the scanner OFF for safety when not

using the scanner for a long period of time, such as overnight. Also,

push the power switch to turn it OFF, and disconnect the power cord

from the power outlet for safety when the machine will not be used

for an extended period of time, such as during consecutive

holidays.

●Do not wear loose clothing or jewelry that may get caught in the

scanner while you are using it. This may result in personal injury. Be

extra careful of neckties and long hair. If anything becomes caught

in the scanner, immediately disconnect the power cord to stop the

scanner.

●Be careful when loading paper into the scanner and when removing

jammed paper. It is possible to cut your hand on the edge of a sheet

of paper.

Disposal

When disposing of this scanner, be sure to follow all local ordinances

and laws or consult with the retailer who sold you the scanner.

When sending the scanner for repairs

When a request is made for repairs, the scanner needs to be sent to

the specified address. When sending the scanner, use the packing

box in which it came. Firmly secure the scanner with packaging

material when you place it in the packing box.

0-00-DR-C125_RG_UK.book Page 20 Thursday, September 8, 2011 6:03 PM

Features of the Scanner

The main features of the document scanner DR-C125 are described

below.

●Compact Design

The scanner has a compact size of 300 (W) x 336 (H) x 235 (D)

(11.81" (W) x 13.2" (H) x 9.25" (D)) mm when the document feed is

open. A newly designed feed mechanism saves space by

eliminating the need for space to eject paper at the front of the

scanner.

●Fast Document Feeding

Documents can be scanned at a speed of up to 25 pages per

minute (when scanning one-sided or two-sided documents of A4

size at 200 dpi).

●Two Eject Paths for Scanning a Variety of Documents

Use the U-turn path to scan paper of standard thickness, or use the

straight path to scan cards and other thick documents.

●High Image Quality

The 600 dpi optical resolution sensor incorporated in the scanner

enables documents to be scanned with high image quality.

●USB 2.0 Interface

The scanner supports Hi-Speed USB 2.0.

●Color/Grayscale Support

Documents can be scanned in 24-bit color or 256-level grayscale.

●Supports a Variety of Scanning Modes

The scanner supports the following scanning modes, depending on

the document type:

• Single-sided or double-sided scanning (with Skip Blank Page

function)

• Continuous or single sheet feed

●Card Scan

You can scan business or ID cards.

●Paper Size Detection

The scanner automatically detects the size of a scanned document

and eliminates any unnecessary space around the edges of the

image when storing the image, even when storing a document of

irregular size.

●Auto Color Detection

The scanner detects whether the scanned document is in color,

grayscale, or black and white (binary), and saves the image

accordingly.

●Full Auto Mode

A Full Auto Mode is provided in CaptureOnTouch and the scanner

driver to allow scanning under automatically determined conditions.

Scanning conditions such as the color mode and page size are set

automatically based on the document being scanned.

●Auto Resolution Detection

When enabled in the CaptureOnTouch or scanner driver settings,

this function detects the content of documents and determines the

scanning resolution automatically.

●Folio Scan

You can scan folded documents. The scanner will scan both sides

and combine the scanned images into a single image.

●Deskew

The scanner straightens scanned images when it detects that the

document was placed askew.

●Ultrasonic Double Feed Detection

Ultrasonic waves are used to detect pages that are fed at the same

time as well as the space between pages. Scanning stops if a

double feed is detected.

●Text Enhancement Modes

The scanner is equipped with the Advanced Text Enhancement

Mode (only for Windows), for enhancing the text of documents with

dark or uneven backgrounds, and the Advanced Text Enhancement

II mode, for enhancing the text when both the text and background

are light.

These modes may not work, depending on the type of document.

●Color Drop-out

The scanner is equipped with a Color Drop-out function that

enables you to specify a color for the scanner to omit from the

scanned image during black and white or grayscale scanning.

●Skip Blank Page Function

The scanner is equipped with a Skip Blank Page function that

enables you to scan a document without storing images of blank

pages, regardless of whether each page of the document is two-

sided or one-sided. Both sides are scanned, but saving the image

is skipped for scan images judged to be from a blank page.

0-00-DR-C125_RG_UK.book Page 21 Thursday, September 8, 2011 6:03 PM

●Prescan Function

The scanner is equipped with a Prescan function that allows you to

adjust the contrast and brightness of a prescanned image and then

send the adjusted image to the application software, without

needing to scan the document again.

●Character/Line Emphasis Function

If characters and lines in scanned images are not clearly visible, you

can use this function to adjust their thickness during scanning.

●Scan First

Pressing Start Button starts CaptureOnTouch. You can then

perform a scan simply by following the on-screen guidance.

●Select Scan Job

You can register scanning conditions and methods for processing

scanned images as jobs, and register up to 10 jobs in

CaptureOnTouch. By simply selecting a registered job, you can

perform scanning operations in a determined order.

●Auto Start

The scanner is equipped with an auto start function, which enables

scanning to be automatically started when a document placed in the

feeder is detected.

●Sleep Mode

The scanner is designed to save energy by entering the sleep mode

when it is not scanning documents.

IMPORTANT

Depending on the bundled software you are using, all of the

preceding features may not be available.

0-00-DR-C125_RG_UK.book Page 22 Thursday, September 8, 2011 6:03 PM

Names and Functions of Parts

Front View

AFront Unit

Open this when removing paper jammed inside the scanner,

cleaning the inside of the scanner, or replacing rollers.

BDocument Eject Pocket

Scanned documents are output here.

CFeed Extension Plates

Pull this out when loading long documents.

DEject Support

Open this when loading long documents.

EFeed Support

Pull out this to support loaded documents.

FDocument Feed Tray

Open this when loading documents for scanning.

GPower Button

This turns the scanner ON and OFF.

HStart Button

This starts scanning the document loaded in the document feed

tray

IFeed Selection Indicator

This indicates the way documents are currently being fed in

accordance with the position of the feed selection lever.

JFeed Selection Lever

This changes the way documents are fed.

KConnectors

Connectors for connecting an AC adapter and USB cable are

available. (See p. 24)

LEject Selection Lever

Use this lever to change the way documents are ejected.

Lever position Indicator color

Upper (non separation feeding) Orange

Lower (standard feeding) Black

0-00-DR-C125_RG_UK.book Page 23 Thursday, September 8, 2011 6:03 PM

Connectors

APower Connector

Connect the supplied AC adapter to this connector.

BUSB Connector

Connect the supplied USB cable to this connector.

Back View

AOPEN Button

Press this button to open the front unit.

BKensington Slot

Connect an anti-theft key chain or the like.

CCable Grooves

Secure the USB cable and power cord that are connected to the

scanner along the rear of the scanner. Use these when you want

to run the cables on the side opposite the connectors.

0-00-DR-C125_RG_UK.book Page 24 Thursday, September 8, 2011 6:03 PM

Documents

The scanner can scan documents ranging in size from business cards

to Legal/A4. The document sizes that this scanner can scan are

shown below.

Plain Paper

Size

Width: 50.8 mm to 216 mm (2" to 8.5")

Length: 53.9 mm to 356 mm (2.12" to 14")*

Paper thickness:

When U-turn path: 52 to 128 g/m2 (14 to 34 lb bond)

0.06 to 0.15 mm (0.0024" to 0.0059")

When straight path: 40 to 209 g/m2 (11 to 58 lb bond)

0.05 to 0.25 mm (0.002" to 0.0098")

* Setting the scanner to Long Document mode enables documents

up to 3,000 mm (118.1") long to be scanned. Refer to the User

Manual for detailed information.

IMPORTANT

The documents to be scanned must satisfy certain criteria. Read the

following items carefully.

• When scanning multiple documents of different sizes, place the

documents so that they cover the entire span of the feed rollers.

• It is recommended that documents exceeding 356 mm (14") in size

are fed one sheet at a time.

• Use the straight path when scanning documents that are 70 mm

(2.76") long or less.

• Scanning documents before the ink is dry can cause problems with

the scanner. Always make sure that the ink on a document is dry

before scanning it.

• Scanning documents that are written in pencil or similar material

may make the rollers and scanning glass dirty, which can lead to

smudges on the scanned image and transfer the dirt to subsequent

documents. Always clean the internal parts of the scanner after

scanning such documents.

• When scanning a two-sided document that is printed on thin paper,

the image on the opposite side of each page may show through. In

this case, adjust the scanning intensity in the application software

before scanning the document.

• It is recommended that thin documents are fed one sheet at a time.

• Scanning the following types of documents can cause a paper jam

or malfunction. To scan such a document, make a photocopy of the

document and then scan the photocopy.

Business Card

Size: 50 mm x 53.9 mm (1.97" x 2.12") or larger

Paper weight: 300 g/m2 (80 lb bond) 0.35 mm (0.0138") or less

Orientation: Vertical feeding only

IMPORTANT

If a stack of business cards cannot be fed properly, reduce the

number of cards in the stack.

Feed rollers

There are creases or

fold lines. Carbon paper

There are curls. The surface is coated.

There are tears.

Extremely thin document

such as semi-transparent

thin paper.

There are clips or

staples.

Documents with excessive

paper dust particles.

0-00-DR-C125_RG_UK.book Page 25 Thursday, September 8, 2011 6:03 PM

Card (plastic or laminated)

Size: 53.9 mm x 85.5 mm (2.12" x 3.37") (ISO standard)

Card thickness: 0.76 mm (0.03") or less, 1.4 mm (0.055") or less for

the embossment

Orientation: Horizontal feeding only

Feed path: Straight path only

Embossed cards can be scanned.

CAUTION

• Use the straight path when scanning cards.

• If you place cards to be fed vertically, they may not be ejected

properly, and cards that get jammed may be damaged when you

remove them. Take care of the orientation when placing cards.

• Embossed cards may not be able to be scanned correctly,

depending on the type of embossment.

0-00-DR-C125_RG_UK.book Page 26 Thursday, September 8, 2011 6:03 PM

How to Place Documents

Switching the Feed and Eject

Methods

Use the two levers on the scanner to switch the feed and eject

methods based on the type of document you are scanning.

The feed and eject methods and lever positions for each document

type are as follows.

Placing Documents for Standard

Feeding

Ordinarily, standard feeding should be used when scanning multiple

documents of a standard size at one time. Standard feeding enables

the multiple documents to be fed while separating each page.

Open the document feed tray.

Pull out the feed support.

Document type Feed method (lever

position)

Eject method (lever

position)

Standard paper

and business

cards

Standard feeding

(lower)

U-turn path (upper) or

straight path (lower)

Plastic cards, thick

paper, thin paper,

and bound or

fastened paper

Non separation

feeding (upper) Straight path (lower)

Feed Selection Lever

Standard Feeding

Eject Selection Lever

U-turn Path Straight Path

Non Separation

Feeding

0-00-DR-C125_RG_UK.book Page 27 Thursday, September 8, 2011 6:03 PM

When scanning long documents, pull out the feed

extension plates and eject support.

Set the feed selection lever and the eject selection lever.

Set the feed selection lever to the standard feeding position (lower

position).

Set the eject selection lever to the U-turn path position ( ).

When scanning documents that contain both standard paper and

plastic cards, use the straight path.

Adjust the document guides to fit the width of the

document to be scanned.

0-00-DR-C125_RG_UK.book Page 28 Thursday, September 8, 2011 6:03 PM

Place the document.

Insert the document in the feed tray so that the front is facing

forward and the top is facing upward.

After inserting the document in the document feeder, align the

document guides with both edges of the document.

IMPORTANT

• When placing documents into the feed tray, take care not to cut

your hands on the edges of the paper.

• Make sure that the document does not exceed the loading limit

marks ( ) on the document guides. Up to 30 pages of ordinary

plain paper (80 g/m2) can be loaded at the same time.

• Before you place a document, check to make sure it does not

contain paper clips, staples, or other small metal objects. These

items may cause a fire or electrical shock, damage the document,

or cause a paper jam or scanner malfunction.

• Do not wear loose clothing or jewelry that may get caught in the

scanner while you are using it. This may result in personal injury. Be

extra careful of neckties and long hair. If anything gets caught in the

scanner, immediately turn OFF the power switch, and disconnect

the power cord from the power outlet to stop scanning.

• Always smooth out any folds or curls in your documents before

placing them into the feeder. If the leading edge of a document is

curled, it may cause a paper jam.

• If feeding stops due to a system error or paper jam while the

scanner is scanning, resolve the problem, make sure that the

scanned image of the last page that was successfully fed has been

stored, and then resume scanning the remaining document pages.

• After you finish scanning, close the document feed tray to prevent

damage to the scanner while it is not being used.

• Although standard feeding can be used in combination with the

straight path when scanning, multi-page documents will be ejected

in reverse order in such cases.

• If you select the [Upside-down feeding] check box in the scanner

driver settings, you can insert documents into the scanner in the

opposite orientation. Refer to the User Manual for detailed

information.

Default

[Upside-down

feeding] selected

0-00-DR-C125_RG_UK.book Page 29 Thursday, September 8, 2011 6:03 PM

Placing Documents for Non

Separation Feeding

When scanning a thick document one page at a time or scanning a

document that has multiple pages fastened together, set document

feeding to non separation mode. This enables the placed document to

be scanned without the pages being separated, regardless of the

number of pages.

Set the feed selection lever and the eject selection lever.

Set the feed selection lever to the non separation position (upper

position). The feed selection indicator will light orange.

Set the eject selection lever to the straight path position ( ).

Adjust the document guides to fit the width of the

document.

0-00-DR-C125_RG_UK.book Page 30 Thursday, September 8, 2011 6:03 PM

Place the document in the document feed tray.

IMPORTANT

• With the straight path, documents are ejected at the front of the

scanner. Do not place anything that will block output near the

document eject area. Also, install the scanner on a smooth

surface to enable documents to be smoothly ejected.

• When scanning multiple page documents that are fastened

together, such as invoices, place the documents so that the

edge that is fastened together is facing down.

Placing Cards

Set the feed selection lever and the eject selection lever.

Set the feed selection lever to the non separation position (upper

position). The feed selection indicator will light orange.

Set the eject selection lever to the straight path position ( ).

Adjust the document guides to fit the width of the card to

be scanned.

0-00-DR-C125_RG_UK.book Page 31 Thursday, September 8, 2011 6:03 PM

Place the card horizontally with the top edge facing

upward.

CAUTION

• Place the card one at a time.

• If you place cards to be fed vertically, they may not be ejected

properly, and cards that get jammed may be damaged when you

remove them. Take care of the orientation when placing cards.

• Ultrasonic double feed detection will not function properly when

scanning cards. Clear the [Detect by Ultrasonic] check box in the

[Feeding] tab.

IMPORTANT

With the straight path, documents are ejected at the front of the

scanner. Do not place anything that will block output near the

document eject area. Also, install the scanner on a smooth surface to

enable documents to be smoothly ejected.

0-00-DR-C125_RG_UK.book Page 32 Thursday, September 8, 2011 6:03 PM

Scanning with CaptureOnTouch (Windows)

What is CaptureOnTouch?

CaptureOnTouch is a scanning application that allows you to scan a

document with a simple operation by following the instructions on the

screen.

CaptureOnTouch is provided with multiple scanning methods that can

be selected according to the purpose and application.

Scan First

Scan a document and then select the output method. This method

allows you to easily scan a document by just following the instructions

on the screen.

Select Scan Job

method as jobs, and then scan a document by just selecting the job

that suits your purpose. This method is convenient when you want to

repeat scanning using a set procedure.

Scan with Start Button

Scan First is pre-assigned to the Start button of the scanner, so you

can load a document and then start scanning by just pressing the Start

button. You can also assign any job to the Start button.

File Formats of Saved Images

You can specify one of the following file formats for scanned images

when using any output method other than [Print].

•PDF

•TIFF

•JPEG

•BMP

• PPTX (file format for Microsoft PowerPoint 2007 or later)

Starting and Exiting CaptureOnTouch

By default, CaptureOnTouch becomes resident in the system when

you start your computer.

Double-click (CaptureOnTouch icon) in the taskbar to start

CaptureOnTouch and display the main window.

Hint

• You can also start CaptureOnTouch from the Start menu. Click

[Start] – [All Programs] – [Canon DR-C125] – [DR-C125

CaptureOnTouch].

• The first time you start CaptureOnTouch on a computer with

Evernote installed, a message for confirming the registration of jobs

for sending scanned images to Evernote appears. If you click the

[Yes] button, two jobs for Evernote are registered to

CaptureOnTouch.

• The interval between the time you press the Start button on the

scanner and the time scanning begins is shortened when the [Make

CaptureOnTouch resident] check box is selected in the [Basic

settings] tab of the [Environmental settings] dialog box. Refer to the

User Manual for detailed information.

Save to folder

Save the file to a

specified folder.

Print with a specified

printer.

(Network)

Send to application

Open the scanned image file

in a specified application.

Attach to E-mail

Start the e-mail application

and attach the scanned image

file to new e-mail

Scanner

Cloud Service

0-00-DR-C125_RG_UK.book Page 33 Thursday, September 8, 2011 6:03 PM

Exiting CaptureOnTouch

To close the CaptureOnTouch window, click at the top of the

window. This closes the window, but CaptureOnTouch will continue to

reside in the system.

To quit the CaptureOnTouch application, click (CaptureOnTouch

icon) in the taskbar, and select [Exit] from the menu.

CaptureOnTouch becomes no longer resident in the system and the

icon disappears from the taskbar.

Restarting CaptureOnTouch

To use CaptureOnTouch after it has been made not resident in the

system, use one of the following procedures to restart it.

CaptureOnTouch will start and become resident in the system again.

• Click [Start] – [All Programs] – [Canon DR-C125] – [DR-C125

CaptureOnTouch].

• Press the Start button on the scanner (in this case, the main screen

of CaptureOnTouch will open and scanning will start using the scan

method assigned to the Start button).

Scan First

Operation Flow

Place the document in the scanner.

Click [Scan First].

The top screen of Scan First appears.

Scan the document

▼

Configure the output settings

▼

Output the scanned images

0-00-DR-C125_RG_UK.book Page 34 Thursday, September 8, 2011 6:03 PM

Set the scan method in the top screen.

ASpecify whether to enable continuous scanning. When

previewing the scanned image or splitting up a large document

to scan in parts, select [ON] to enable continuous scanning.

BSpecify whether to scan the document in full auto mode. When

you want to specify arbitrary scanning conditions, select [OFF]

and configure the scanner settings. (See p. 39)

Click the Start button.

The document is scanned. While scanning is in progress, the

number of pages scanned is displayed in addition to the scanner

settings.

When scanning is finished, the Output settings screen appears.

IMPORTANT

If you configure scanning conditions that consume a large

amount of the computer’s memory, scanning may stop because

of insufficient memory. If an error message appears due to

insufficient memory while scanning is in progress, exit the

application, change the scanning conditions, and then try

scanning again.

Hint

If a document is scanned when [Enable continuous scanning] is

set to [ON], the continuous scanning screen (see p. 41) appears

when scanning of the document is finished.

If you place the next document and click [Scan], scanning of the

document starts.

When scanning of all the documents is finished, click [Next step].

0-00-DR-C125_RG_UK.book Page 35 Thursday, September 8, 2011 6:03 PM

Configure the settings related to output and then output

the scanned images.

AConfigure the settings related to output. (See p. 42)

BClick this button to output the scanned images. The button

name differs for each output method. For example, it is [Save]

when the output method is set to [Save to folder].

When output is finished, the complete screen appears. Scan First

is now finished.

Hint

• Clicking [Return to top] returns to the main screen of Scan First.

• When [Attach to E-mail] or [Print] is specified as the output method,

you can click [Open storage folder] to open the folder in which the

scanned images were saved.

Select Scan Job

Operation Flow

Registering and Editing Jobs

In CaptureOnTouch, up to 10 jobs can be registered for use with

Select Scan Job.

Click the button.

▼

Select the job

▼

Scan the document

▼

Output the scanned images

0-00-DR-C125_RG_UK.book Page 36 Thursday, September 8, 2011 6:03 PM

Enter the job name, and press the Enter key.

Specify the output method of the job. (See p. 42)

Hint

You can assign the job to the Start button by selecting [Start

button] for [Button assignment]. (See p. 39)

Click [Output setting], and configure the output settings.

The output setting items differ depending on the specified output

method. For details on the setting items, see the Help of

CaptureOnTouch.

Selecting a Job and Scanning

Place the document in the scanner. (See p. 27)

The top screen of Select Scan Job appears.

Click a job.

0-00-DR-C125_RG_UK.book Page 37 Thursday, September 8, 2011 6:03 PM

Hint

• If you set [Check output after scanning] to [ON], you can check

the output settings after scanning.

• If you set [Enable continuous scanning] to [ON], you can

continue scanning after all the pages of the document are

scanned.

Click the Start button.

The document is scanned. While scanning is in progress, the

number of pages scanned is displayed in addition to the scanner

settings.

When all the pages of the document are scanned, the scanned

images are output according to the registered job settings and the

complete screen appears.

IMPORTANT

If you configure scanning conditions that consume a large amount of

the computer’s memory, scanning may stop because of insufficient

memory. If an error message appears due to insufficient memory

while scanning is in progress, exit the application, change the

scanning conditions, and then try scanning again.

Hint

• Clicking [Return to top] returns to the top screen of Select Scan Job.

• When [Attach to E-mail] or [Print] is specified as the output method,

you can click [Open storage folder] to open the folder in which the

scanned images were saved.

When [Enable continuous scanning] is set to [ON]

The continuous scanning screen (see p. 41) appears when all the

pages of the document are scanned.

If you want to scan another document, place the document in the

scanner and then click [Scan].

When scanning of all the documents is finished, click [Next step].

0-00-DR-C125_RG_UK.book Page 38 Thursday, September 8, 2011 6:03 PM

When [Check output after scanning] is set to [ON]

The Output Confirmation screen appears before the scanned images

are output.

Change the settings for the output method if necessary and then click

the output button. The name of the output button differs for each

selected output method.

Scanning with Start Button

By default, Scan First is pre-assigned to the Start button.

If you place the document and press the Start button,

CaptureOnTouch starts and scanning starts.

Hint

You can also assign any job to the Start button. If a job is assigned,

the document is scanned and the scanned images are output

according to the settings of the job. The main window of

CaptureOnTouch closes automatically 5 seconds after the output

process finishes.

Scanner Settings

By default, CaptureOnTouch scans with scanning conditions that

match the document because scanning in full auto mode is enabled.

If you want to specify, for example, the scanning mode and document

size, you can configure the desired scanning conditions in the scanner

settings.

The scanner setting items are common to Scan First and Select Scan

Job.

When Scan First:

For Scan First, configure the scanner settings before you start

scanning.

Start button

0-00-DR-C125_RG_UK.book Page 39 Thursday, September 8, 2011 6:03 PM

When Select Scan Job:

For Select Scan Job, configure the scanner settings for each job.

Setting Basic Items

Scanner settings include the basic items that are configured in

[Scanner setting], and the setting items that are configured in the

advanced settings dialog box. The settings in the advanced settings

dialog box are applied for settings other than the basic items.

The settings in the driver settings dialog box are applied for any other

settings.

Color mode

Select from the following modes for scanning documents.

Detect automatically Automatically determines the color mode based

on the document content and scans

accordingly.

24-bit Color Scans the document in color.

Grayscale Scans the document in Grayscale.

Black and White Scans the document in black and white

(binary).

Page Size

Specify the page size of the document.

If you specify [Match original size], the page size of the scanned

document is detected and the images are saved at the detected size.

Dots per inch

Specify the scanning resolution.

When [Detect automatically] is specified, the resolution is detected

automatically from the content of the scanned document.

Scanning Side

Specify whether to scan only one side or both sides of a document.

When [Skip blank page] is specified, any blank paged detected within

the document is skipped during scanning.

Automatically straightens skewed images

When a document is scanned skewed, the skewed scanned images

are detected and then straightened.

Rotate image to match orientation of text

The orientation of text in scanned images is detected, and the images

are rotated so that the text is correctly oriented.

Use advanced settings dialog box

Configure scanner settings other than the basic items in the advanced

settings dialog box (scanner driver). To open the scanner driver,

select [ON] and then click the button.

For details on the setting items, see the Help of the driver settings

dialog box.

Hint

The driver settings dialog box includes setting items that are the

same as the basic items in [Scanner setting], but the setting for each

of the them is stored separately. Which settings are used during

scanning differs as follows depending on the setting of the [Use

advanced settings dialog box] check box.

0-00-DR-C125_RG_UK.book Page 40 Thursday, September 8, 2011 6:03 PM

Operation in Continuous Scanning

Screen

When [Enable continuous scanning] is set to [ON] in the Start screen,

the continuous scanning screen appears when all of the pages of the

placed document have been fed. You can confirm the scanned

images and then continue scanning.

AThumbnail Display Area

Displays the thumbnail images of the scanned document. The

following operations are possible.

Click a thumbnail image to display a preview of that scanned image

in the preview area.

Drag thumbnail images to change the positions of pages (Scan

First only).

Click on a thumbnail image to delete the scanned image for that

page (Scan First only).

BPreview Area

Displays the preview images of the scanned document.

CPreview Controls

Control the preview images and cancel or continue scanning with

the following buttons.

Setting of [Use

advanced settings

dialog box]

Basic items Other than basic

items

OFF Settings of [Scanner

setting]

Settings of the

advanced settings

dialog box of the

scanner driver

ON Settings of the advanced settings dialog box

of the scanner driver

Tools (Name) Description

(Zoom in) Enlarges the preview image.

(Fit page) Enlarges or reduces the preview image

to fit the current window size.

(Zoom out) Reduces the preview image.

(Rotate left) Rotates the image 90 degrees

counterclockwise. (Scan First only)

(Rotate right) Rotates the image 90 degrees

clockwise. (Scan First only)

(Rotate 180) Rotates the image 180 degrees. (Scan

First only)

(Cancel) Cancels the image scanning operation

and returns to the top screen.

(Scan) Starts scanning of the next document.

(Next step) Proceeds to the next step in the scan

process.

(Page Number /

Total Number of

Pages)

Displays the current page and total

number of pages.

0-00-DR-C125_RG_UK.book Page 41 Thursday, September 8, 2011 6:03 PM

Setting the Output Method

CaptureOnTouch is provided with various output methods for

processing scanned images.

The output method specification is common to Scan First and Select

Scan Job.

When Scan First:

For Scan First, select an output method in the output method selection

screen that appears after scanning, and then specify each of the

output method items.

When Select Scan Job:

For Select Scan Job, specify the output method separately for each

job.

The setting items related to output differ depending on the output

method.

Save to folder

Saves the scanned images to a specified folder. When you specify this

output method, configure the settings for the image files to be saved.

Attach to E-mail

Attaches the scanned images to new e-mail in the e-mail application.

When you specify this output method, configure the settings for the

image files to be attached to e-mail.

To use this feature, an e-mail application such as Windows Mail or

Outlook Express (both of these applications come standard with the

operating system) that supports MAPI (Messaging Application

Programming Interface) needs to be specified as the default program

of the operating system.

Prints the scanned images with a specified printer. When you specify

this output method, specify the printer for printing.

Send to application

Saves the scanned image file in a specified folder and then opens it

with a specified application. When you specify this output method,

click the button next to [Application] and specify the executable file

of an application that can open image files. In addition, configure the

settings of the image file to be saved.

Other Output Methods

Depending on the plug-ins you installed during installation of

CaptureOnTouch, you can select the following output methods. You

must configure settings for the saved image file, regardless of your

output method selection.

• Save in Google docs

Saves the scanned images to Google docs. When using this output

method, open the settings screen by clicking next to [Detail

Settings], and then enter the account information and configure the

destination settings. For details on the settings, see the Help (click

the [Help] button in the settings screen).

• Save in Evernote

Saves the scanned images to Evernote.

• Save in Microsoft SharePoint

In an environment in which Microsoft SharePoint has been

introduced, you can save the scanned images to a Microsoft

SharePoint site. When using this output method, open the advanced

settings screen by clicking next to [Detail Settings], and configure

settings such as the URL of the Microsoft SharePoint site, the

account information, and the destination file settings. For details on

the settings, see the Help (click the [Help] button in the settings

screen).

IMPORTANT

To use the [Save in Google docs] and [Save in Evernote] output

methods, the respective cloud service accounts are required. (See

p. 6)

0-00-DR-C125_RG_UK.book Page 42 Thursday, September 8, 2011 6:03 PM

Scanning with CaptureOnTouch (Mac OS X)

What is CaptureOnTouch?

CaptureOnTouch is a scanning application that allows you to scan a

document with a simple operation by following the instructions on the

screen.

CaptureOnTouch is provided with multiple scanning methods that can

be selected according to the purpose and application.

Scan First

Scan a document and then select the output method. This method

allows you to easily scan a document by just following the instructions

on the screen.

Select Scan Job

method as jobs, and then scan a document by just selecting the job

that suits your purpose. This method is convenient when you want to

repeat scanning using a set procedure.

Scan with Start Button

Scan First is pre-assigned to the Start button of the scanner, so you

can load a document and then start scanning by just pressing the Start

button. You can also assign any job to the Start button.

File Formats of Saved Images

You can specify one of the following file formats for scanned images

when using any output method other than [Print].

•PDF

•TIFF

•JPEG

Launching and Quitting

CaptureOnTouch

By default, CaptureOnTouch becomes resident in the system when

you start your computer.

Click (CaptureOnTouch icon) in the menu bar and then click

[Launch CaptureOnTouch] from the menu which appears to start

CaptureOnTouch and display the main window.

Hint

• The first time you launch CaptureOnTouch on a computer with

Evernote installed, a message for confirming the registration of jobs

for sending scanned images to Evernote appears. If you click the

[OK] button, two jobs for Evernote are registered to

CaptureOnTouch.

• The interval between the time you press the Start button on the

scanner and the time scanning begins is shortened when the [Make

CaptureOnTouch resident] check box is selected in the [Basic

settings] tab of the [Environmental settings] dialog box. Refer to the

User Manual for detailed information.

Save to folder

Save the file to a

specified folder.

Print with a specified

printer.

(Network)

Send to application

Open the scanned image file

in a specified application.

Attach to E-mail

Start the e-mail application

and attach the scanned image

file to new e-mail

Scanner

Cloud Service

0-00-DR-C125_RG_UK.book Page 43 Thursday, September 8, 2011 6:03 PM

Quitting CaptureOnTouch

To close the CaptureOnTouch window, click at the top of the

window. This closes the window, but CaptureOnTouch will continue to

reside in the system.

To quit the CaptureOnTouch application, click (CaptureOnTouch

icon) in the menubar, and select [Exit] from the menu.

Restarting CaptureOnTouch

To use CaptureOnTouch after it has been made not resident in the

system, use one of the following procedures to restart it.

CaptureOnTouch will launch and become resident in the system

again.

• Open [Applications] - [Canon DR-C125] folder from the Finder, and

double-click [CaptureOnTouch DR-C125].

• Press the Start button on the scanner (in this case, the main screen

of CaptureOnTouch will open and scanning will start using the scan

method assigned to the Start button).

Scan First

Operation Flow

Place the document in the scanner.

Click [Scan First].

The top screen of Scan First appears.

Scan the document

▼

Configure the output settings

▼

Output the scanned images

0-00-DR-C125_RG_UK.book Page 44 Thursday, September 8, 2011 6:03 PM

Set the scan method in the top screen.

ASpecify whether to enable continuous scanning. When

previewing the scanned image or splitting up a large document

to scan in parts, select [ON] to enable continuous scanning.

BSpecify whether to scan the document in full auto mode. When

you want to specify arbitrary scanning conditions, select [OFF]

and configure the scanner settings. (See p. 49)

Click the Start button.

The document is scanned. While scanning is in progress, the

number of pages scanned is displayed in addition to the scanner

settings.

When scanning is finished, the Output settings screen appears.

IMPORTANT

If you configure scanning conditions that consume a large

amount of the computer’s memory, scanning may stop because

of insufficient memory. If an error message appears due to

insufficient memory while scanning is in progress, exit the

application, change the scanning conditions, and then try

scanning again.

Hint

If a document is scanned when [Enable continuous scanning] is

set to [ON], the continuous scanning screen (see p. 51) appears

when scanning of the document is finished.

If you place the next document and click [Scan], scanning of the

document starts.

When scanning of all the documents is finished, click [Next].

0-00-DR-C125_RG_UK.book Page 45 Thursday, September 8, 2011 6:03 PM

Configure the settings related to output and then output

the scanned images.

AConfigure the settings related to output. (See p. 42)

BClick this button to output the scanned images. The button

name differs for each output method. For example, it is [Save]

when the output method is set to [Save to folder].

When output is finished, the complete screen appears. Scan First

is now finished.

Hint

• Clicking [Return to top] returns to the main screen of Scan First.

• When [Attach to E-mail] or [Print] is specified as the output method,

you can click [Open storage folder] to open the folder in which the

scanned images were saved.

Select Scan Job

Operation Flow

Registering and Editing Jobs

In CaptureOnTouch, up to 10 jobs can be registered for use with

Select Scan Job.

Click the button.

▼

Select the job

▼

Scan the document

▼

Output the scanned images

0-00-DR-C125_RG_UK.book Page 46 Thursday, September 8, 2011 6:03 PM

Enter the job name, and press the Enter key.

Specify the output method of the job. (See p. 42)

Hint

You can assign the job to the Start button by selecting [Start

button] for [Button assignment]. (See p. 49)

Click [Output setting], and configure the output settings.

The output setting items differ depending on the specified output

method. For details on the setting items, see the Help of

CaptureOnTouch.

Selecting a Job and Scanning

Place the document in the scanner. (See p. 27)

The top screen of Select Scan Job appears.

Click a job.

0-00-DR-C125_RG_UK.book Page 47 Thursday, September 8, 2011 6:03 PM

Hint

• If you set [Check output after scanning] to [ON], you can check

the output settings after scanning.

• If you set [Enable continuous scanning] to [ON], you can

continue scanning after all the pages of the document are

scanned.

Click the Start button.

The document is scanned. While scanning is in progress, the

number of pages scanned is displayed in addition to the scanner

settings.

When all the pages of the document are scanned, the scanned

images are output according to the registered job settings and the

complete screen appears.

IMPORTANT

If you configure scanning conditions that consume a large amount of

the computer’s memory, scanning may stop because of insufficient

memory. If an error message appears due to insufficient memory

while scanning is in progress, exit the application, change the

scanning conditions, and then try scanning again.

Hint

• Clicking [Return to top] returns to the top screen of Select Scan Job.

• When [Attach to E-mail] or [Print] is specified as the output method,

you can click [Open storage folder] to open the folder in which the

scanned images were saved.

When [Enable continuous scanning] is set to [ON]

The continuous scanning screen (see p. 51) appears when all the

pages of the document are scanned.

If you want to scan another document, place the document in the

scanner and then click [Scan].

When scanning of all the documents is finished, click [Next].

0-00-DR-C125_RG_UK.book Page 48 Thursday, September 8, 2011 6:03 PM

When [Check output after scanning] is set to [ON]

The Output Confirmation screen appears before the scanned images

are output.

Change the settings for the output method if necessary and then click

the output button. The name of the output button differs for each

selected output method.

Scanning with Start Button

By default, Scan First is pre-assigned to the Start button.

If you place the document and press the Start button,

CaptureOnTouch launches and scanning starts.

Hint

If a job is assigned to the Start button, the document is scanned and

the scanned images are output according to the settings of the job.

CaptureOnTouch ends automatically 5 seconds after the output

process finishes.

Scanner Settings

By default, CaptureOnTouch scans with scanning conditions that

match the document because scanning in full auto mode is enabled.

If you want to specify, for example, the scanning mode and document

size, you can configure the desired scanning conditions in the scanner

settings.

The scanner setting items are common to Scan First and Select Scan

Job.

When Scan First:

For Scan First, configure the scanner settings before you start

scanning.

Start button

0-00-DR-C125_RG_UK.book Page 49 Thursday, September 8, 2011 6:03 PM

When Select Scan Job:

For Select Scan Job, configure the scanner settings for each job.

Setting Basic Items

Scanner settings include the basic items that are configured in

[Scanner setting], and the setting items that are configured in the

advanced settings dialog box. The settings in the advanced settings

dialog box are applied for settings other than the basic items.

The settings in the driver settings dialog box are applied for any other

settings.

Color mode

Select from the following modes for scanning documents.

Detect automatically Automatically determines the color mode based

on the document content and scans

accordingly.

24-bit Color Scans the document in color.

Grayscale Scans the document in Grayscale.

Black and White Scans the document in black and white

(binary).

Page Size

Specify the page size of the document.

If you specify [Match original size], the page size of the scanned

document is detected and the images are saved at the detected size.

Dots per inch

Specify the scanning resolution.

When [Detect automatically] is specified, the resolution is detected

automatically from the content of the scanned document.

Scanning Side

Specify whether to scan only one side or both sides of a document.

When [Skip blank page] is specified, any blank paged detected within

the document is skipped during scanning.

Automatically straightens skewed images

When a document is scanned skewed, the skewed scanned images

are detected and then straightened.

Rotate image to match orientation of text

The orientation of text in scanned images is detected, and the images

are rotated so that the text is correctly oriented.

Use advanced settings dialog box

Configure scanner settings other than the basic items in the advanced

settings dialog box. To open the advanced settings dialog box, select

[ON] and then click the button.

For details on the setting items, see the Help of the driver settings

dialog box.

Hint

The driver settings dialog box includes setting items that are the

same as the basic items in [Scanner setting], but the setting for each

of the them is stored separately. Which settings are used during

scanning differs as follows depending on the setting of the [Use

advanced settings dialog box] check box.

0-00-DR-C125_RG_UK.book Page 50 Thursday, September 8, 2011 6:03 PM

Operation in Continuous Scanning

Screen

If a document is scanned with either Scan First or Select Scan Job

when [Enable continuous scanning] is set to [ON] in the Start screen,

the continuous scanning screen appears when all of the pages of the

placed document have been fed. You can confirm the scanned

images and then continue scanning.

AThumbnail Display Area

Displays the thumbnail images of the scanned document. The

following operations are possible.

Click a thumbnail image to display a preview of that scanned image

in the preview area.

Drag thumbnail images to change the positions of pages (Scan

First only).

Click on a thumbnail image to delete the scanned image for that

page (Scan First only).

BPreview Area

Displays the preview images of the scanned document.

CPreview Controls

Control the preview images and cancel or continue scanning with

the following buttons.

Setting of [Use

advanced settings

dialog box]

Basic items Other than basic

items

OFF Settings of [Scanner

setting]

Settings of the

advanced settings

dialog box of the

scanner driver

ON Settings of the advanced settings dialog box

of the scanner driver

Tools (Name) Description

(Zoom in) Enlarges the preview image.

(Fit page) Enlarges or reduces the preview image

to fit the current window size.

(Zoom out) Reduces the preview image.

(Rotate left) Rotates the image 90 degrees

counterclockwise. (Scan First only)

(Rotate right) Rotates the image 90 degrees

clockwise. (Scan First only)

(Rotate 180) Rotates the image 180 degrees. (Scan

First only)

(Cancel) Cancels the image scanning operation

and returns to the top screen.

(Scan) Starts scanning of the next document.

(Next) Proceeds to the next step in the scan

process.

(Page Number /

Total Number of

Pages)

Displays the current page and total

number of pages.

0-00-DR-C125_RG_UK.book Page 51 Thursday, September 8, 2011 6:03 PM

Setting the Output Method

CaptureOnTouch is provided with various output methods for

processing scanned images.

The output method specification is common to Scan First and Select

Scan Job.

When Scan First:

For Scan First, select an output method in the output method selection

screen that appears after scanning, and then specify each of the

output method items.

When Select Scan Job:

For Select Scan Job, specify the output method separately for each

job.

The setting items related to output differ depending on the output

method.

Save to folder

Saves the scanned images to a specified folder. When you specify this

output method, configure the settings for the image files to be saved.

Attach to E-mail

Attaches the scanned images to new e-mail in the e-mail application.

When you specify this output method, configure the settings for the

image files to be attached to e-mail.

To use this feature, your e-mail application needs to be specified as

the default program of the operating system. The following shows

examples of typical software that is supported.

• Mail (application that comes standard with the operating system)

• Microsoft Entourage 2004 for Mac

Prints the scanned images with a specified printer. When you specify

this output method, specify the printer for printing.

Send to application

Saves the scanned image file in a specified folder and then opens it

with a specified application. When you specify this output method,

specify the executable file of an application that can open image files.

In addition, configure the settings of the image file to be saved.

Save in Google docs

Sends the scanned images to Google docs. When you specify this

output method, configure the settings for the image files to be saved.

A Google account is required to use this output method. If you click the

button next to [Detail Settings], you can enter account information

and configure destination settings.

0-00-DR-C125_RG_UK.book Page 52 Thursday, September 8, 2011 6:03 PM

Daily Maintenance

Replacing Consumable Parts

The two rollers (feed roller and retard roller) installed in the scanner

are consumable parts. The feed roller and retard roller wear with

scanning. If the feed roller and retard roller are worn, documents may

not feed correctly and paper jams or double-feed errors may occur.

When more than 100,000 pages have been fed (total number of pages

fed by the scanner), a message prompting you to replace the rollers is

displayed when the computer is started.

If this message begins to be displayed at startup, purchase an

exchange roller kit and replace the worn parts with the consumable

parts included in the kit (feed roller and retard roller). For details on the

exchange roller kit, see p. 65.

Furthermore, the counter in the scanner that records the number of

pages fed also needs to be reset when you replace the rollers. (See

p. 56)

Opening and Closing the Front Unit

Open the document feed tray. Press the OPEN button and

pull open the front unit toward you.

Hint

The location of each of the consumable parts is shown below.

Feed roller/document

holding guide (inside the

front unit)

Retard roller

0-00-DR-C125_RG_UK.book Page 53 Thursday, September 8, 2011 6:03 PM

When closing the front unit, make sure that it is

completely closed by gently pressing the left and right

until you hear a click.

Close the document feed tray.

Replacing the Feed Roller

Open the roller cover.

Slide the feed roller to the left, and then remove it.

Install the new feed roller. When installing the feed roller,

align the notch on the roller with the shaft of the front unit.

0-00-DR-C125_RG_UK.book Page 54 Thursday, September 8, 2011 6:03 PM

Slide the roller to the right to secure it.

Close the roller cover. Make sure that it is completely

closed by pressing until you hear a click.

Replacing the Retard Roller

Open the roller cover.

Remove the retard roller and then install the new retard

roller. When installing the retard roller, align the notch on

the roller with the shaft of the main unit.

Close the roller cover. Make sure that it is completely

closed by pressing until you hear a click.

0-00-DR-C125_RG_UK.book Page 55 Thursday, September 8, 2011 6:03 PM

Resetting the Counters

Under Windows

Start Windows and log in as a user with administrator

privileges.

Click the Start button, and then click [All Programs],

[Canon DR-C125], and [Canon imageFORMULA Utility].

imageFORMULA Utility starts.

Click [CANON DR-C125 USB] and click [Properties].

The scanner’s properties appear.

Click the [Maintenance] tab, and click [Reset].

The counter for [Current Rollers] resets.

Click [OK] to close the scanner properties.

Under Mac OS X

Start CaptureOnTouch.

Click [Scan First].

Click [OFF] next to [Scans in the full auto mode].

Click the [Scanner setting] button.

Click [ON] next to [Use advanced settings dialog box].

Click .

This will open the advanced settings dialog box for the scanner.

0-00-DR-C125_RG_UK.book Page 56 Thursday, September 8, 2011 6:03 PM

Click to display the [Scanner Information] dialog box.

Click [Maintenance] to display the [Maintenance] dialog

box.

Click [Reset].

Click to close the [Maintenance] dialog box.

Auto Power Off Setting

The scanner automatically turns off if 4 hours elapse without scanning

or another operation being performed.

To disable this setting, follow the procedure below.

IMPORTANT

The Auto Power Off setting is only available in Windows.

Start Windows and log in as a user with administrator

privileges.

Click the Start button, and then click [All Programs],

[Canon DR-C125], and [Canon imageFORMULA Utility].

imageFORMULA Utility starts.

Click [CANON DR-C125 USB] and click [Properties].

Scanner properties are displayed.

0-00-DR-C125_RG_UK.book Page 57 Thursday, September 8, 2011 6:03 PM

Click the [Maintenance] tab and then clear the [Turn off

automatically after 4 hours] check box.

Click [OK] to close the scanner properties.

0-00-DR-C125_RG_UK.book Page 58 Thursday, September 8, 2011 6:03 PM

Common Problems and Solutions

This section provides recommended solutions to common problems.

If you have a problem that is not solved by the following, contact your

local authorized Canon dealer.

Problem 1 The scanner will not turn on.

Solutions Confirm that the AC adapter is plugged firmly into a

power outlet.

Problem 2 The scanner is not recognized.

Solutions (1) Confirm that the scanner is properly connected to

the computer with a USB cable.

(2) Confirm that the scanner is turned on. See the

previous “Problem 1” if the scanner does not turn

on.

(3) The computer’s USB interface may not support the

scanner. The scanner cannot be guaranteed to

work with all USB interfaces.

(4) Confirm that the supplied USB cable is used to

connect the scanner to the computer. The scanner

cannot be guaranteed to work with all available USB

cables.

(5) If the scanner is connected to the computer via a

USB hub, try removing the hub and connecting

directly to the computer.

Problem 3 Documents feed askew (scanned images are

slanted).

Solutions (1) Align the document guides to fit the documents as

closely as possible, and load the documents so that

they feed straightly.

(2) Enable [Automatically straightens skewed images]

(or [Deskew]) in the scanner driver settings.

(3) If many pages have been scanned since roller

cleaning, clean the rollers. If documents still feed

askew, roller replacement or other maintenance

may be needed. Refer to the User Manual for

detailed information.

Problem 4 Documents are not scanned according to the

settings configured in the scanner driver.

Solutions When you scan using a job registered with

CaptureOnTouch, the registered job settings have

priority over the scanner driver settings. Edit existing job

settings, or create a new job using the desired scanning

conditions.

Problem 5 If white lines or streaks appear in scanned images.

Solutions Clean both sides of the scanner glass, and the rollers. If

a sticky substance such as glue or correction fluid is

found, carefully wipe with just enough pressure to clean

the area where the lines appear. If the problem cannot

be solved by cleaning, the internal glass may be

scratched. Contact your local authorized Canon dealer.

Problem 6 Pages are missing.

Solutions Then the scanner driver’s [Scanning Side] setting is

[Skip blank page], documents with very little black may

be unintentionally skipped. Decrease the [Set the

likelihood of skipping blank page] value, or select

another scan mode setting such as [Simplex] or

[Duplex]. Refer to the User Manual for detailed

information. If pages are skipped due to the document

double feeding, see “Problem 7 Documents jam (or

double-feed)”.

Problem 7 Documents jam (or double-feed).

Solutions (1) If the roller has been installed correctly, clean it if

necessary.

(2) Proper scanning may not be possible when

document pages stick together due to static

electricity. Fan the documents before you load

them.

(3) Set the feed selection lever to the non separation

position, and manually feed the scanner one page at

a time.

0-00-DR-C125_RG_UK.book Page 59 Thursday, September 8, 2011 6:03 PM

Problem 8 Multiple pages of scanned images cannot be saved

to a single file.

Solutions Depending on the file format, multiple scanned image

pages cannot be saved as a single file with

CaptureOnTouch Lite and CaptureOnTouch.

File type Processing for multiple pages

BMP (Windows

only), JPEG

Scanned images are always saved one

page per file.

PPTX (Windows

only)

Multi-page images are always saved to a

single file.

TIFF, PDF

You can save multiple pages to a single

file by clicking and selecting [Save all

pages as one file] in the displayed dialog

box.

Problem 9 All of the placed documents have been scanned, but

the scanned image does not appear on the

application.

Solutions When [Panel-Feeding] or [Automatic Feeding] is

selected as the feeding method on the scanner driver’s

setting screen, a scanning operation will not continue

after all of the documents are fed, as the scanner awaits

additional documents to be fed. You can finish the

operation and send the scanned images to the

application by pressing the [STOP] button on the

operating panel.

Problem 10 Memory becomes insufficient and scanning stops.

Solutions If you configure scanning conditions that use a large

amount of the computer's memory, scanning may stop

because of insufficient memory. Although this depends

on the computer's memory size, the possibility of

insufficient memory increases if any of the following

scanning conditions overlap.

• [Color Mode] is set to [24-bit Color]

• A large page size (e.g. Legal) is specified as the [Page

Size]. Alternatively, the page size is set to [Scanner's

Maximum].

• A high resolution (600dpi etc.) is specified for [Dots per

inch].

If an error message appears due to insufficient memory

while scanning is in progress, exit the application,

change the scanning conditions (e.g. reduce the

resolution or page size) and then try scanning again. In

addition, the amount of memory used can be contained

by turning off [Moire Reduction] and [Please change

prevent bleed through and remove] if they are set to on.

Problem 11 Scanned images are upside down.

Solutions Confirm the scanner driver settings.

In Windows, confirm that the [Upside-down feeding]

check box in the [Feeding] tab is cleared.

In Mac OS X, confirm that the [Upside-down feeding]

check box in the [More] dialog box is cleared.

0-00-DR-C125_RG_UK.book Page 60 Thursday, September 8, 2011 6:03 PM

Clearing a Paper Jam

When paper jams occur during scanning, use the following procedure

to clear them.

WARNING

Be careful when removing jammed paper. It is possible to cut your

hand on the edge of a sheet of paper.

Remove any documents that have been left in the eject

tray.

When the jammed document is on the document ejecting

side, open the document eject tray.

Remove the jammed document.

0-00-DR-C125_RG_UK.book Page 61 Thursday, September 8, 2011 6:03 PM

Return the document eject tray to its original position.

Make sure that it is completely closed by pushing until

you hear a click.

Press the OPEN button and pull open the front unit

toward you.

Remove the jammed document.

IMPORTANT

Make sure to pull the document out carefully, without applying too

much force. If the jammed paper tears while you are pulling it out,

make sure to remove any remaining pieces from inside the

scanner.

0-00-DR-C125_RG_UK.book Page 62 Thursday, September 8, 2011 6:03 PM

Close the front unit by gently pushing it up on both sides

until it clicks into place. Make sure that the front unit is

completely closed by pushing until you hear a click.

After removing the jammed paper, check to see if the last page

was scanned correctly, and then continue scanning.

Hint

When a paper jam or other problem occurs while [Rapid recovery

system] is enabled in the scanner driver, the image of the last

document that was scanned properly is saved before scanning is

stopped. Therefore, you can quickly resume scanning after resolving

the cause of the interruption. As the image of the document that was

being fed at the time of the interruption may not be saved in such

cases, be sure to verify the last scanned image before resuming the

operation.

0-00-DR-C125_RG_UK.book Page 63 Thursday, September 8, 2011 6:03 PM

Specifications

Main Unit

Type Desktop sheetfed scanner

Scanning Document Size

Plain Paper

Size Width: 50.8 mm to 216 mm (2" to 8.5")

Length: 53.9 mm to 356 mm (2.12" to 14")

(You can scan documents up to 3,000 mm

(118.1") long by setting the scanner to the Long

Document mode.)

Thickness When U-turn path: 52 to 128 g/m2 (14 to 34 lb

bond) 0.06 to 0.15 mm (0.0024" to 0.0059")

When straight path: 40 to 209 g/m2 (11 to 58 lb

bond) 0.05 to 0.25 mm (0.002" to 0.0098")

Business Card

Size: 50 mm x 53.9 mm (1.97" x 2.12") or larger

Paper weight: 300 g/m2 (80 lb bond) 0.35 mm (0.0138") or less

Orientation: Vertical feeding only

Card

Size: 53.9 mm x 85.5 mm (2.12" x 3.37") (ISO standard)

Card thickness: 0.76 mm (0.03") or less, 1.4 mm (0.055") or less

for the embossment

Orientation: Horizontal feeding only

Feed path: Straight path only

Embossed cards can be scanned.

Document Feeding Method

Automatic

Scanning Sensor Contact image sensor

Light source LED

Scanning Side Simplex/duplex

Scanning modes Black and White, Error Diffusion, 256-level

Grayscale, Advanced Text Enhancement,

Advanced Text Enhancement II, 24-bit Color

Scanning resolution

150 x 150dpi/200 x 200dpi/300 x 300dpi/

400 x 400dpi/600 x 600dpi

Scanning Speed (Conditions: Core 2 Duo 3.0GHz CPU, 2 GB

memory, A4 document size)

Black and white Simplex 200dpi 25 pages/min.

300dpi 25 pages/min.

Duplex 200dpi 50 images/min.

300dpi 50 images/min.

Grayscale Simplex 200dpi 25 pages/min.

300dpi 25 pages/min.

Duplex 200dpi 50 images/min.

300dpi 50 images/min.

24-bit Color Simplex 200dpi 25 pages/min.

300dpi 15 pages/min.

Duplex 200dpi 50 images/min.

300dpi 30 images/min.

Interface Hi-Speed USB 2.0

Other functions Folio scanning

External Dimensions

300 mm (11.81")(W) x 217 mm (8.54")(H) x 156

mm (6.14")(D)

(with the feed tray close).

300 mm (11.81")(W) x 336 mm (13.2")(H) x 235

mm (9.25")(D)

(with the feed tray open).

Weight (without AC adapter)

Approximately 2.6 kg (5.73 lb)

Power Supply (using AC adapter)

DC16V 1.0A

Power Consumption

100V Scanning: maximum 12.7 W; in the sleep mode:

maximum 1.8 W; with power switch OFF:

maximum 0.5 W

120V Scanning: maximum 12.7 W; in the sleep mode:

maximum 1.8 W; with power switch OFF:

maximum 0.5 W

200 - 240V Scanning: maximum 12.8 W; in the sleep mode:

maximum 1.9 W; with power switch OFF:

maximum 0.5 W

Noise Not more than 56 dB

0-00-DR-C125_RG_UK.book Page 64 Thursday, September 8, 2011 6:03 PM

Operating Environment

Temperature: 10°C to 32.5°C (50°F to 90.5°F)

Humidity: 20% to 80% RH

AC Adapter (100 to 240 V type)

Model Number MG1-4578

Input AC 100 to 240 V, 50/60 Hz, 0.3 to 0.53 A

Output DC 16 V, 1.8 A

Weight Approximately 0.2 kg (0.44 lb) (excluding power

cord)

Replacement parts

Exchange roller kit (product code: 5484B001)

Kit to replace the rollers (feed roller, retard roller) and document

holding guide.

• For the replacement procedure, see “Replacing Consumable Parts”

on p. 53.

• Contact your local authorized Canon dealer or service

representative for detailed information about the replacement parts.

0-00-DR-C125_RG_UK.book Page 65 Thursday, September 8, 2011 6:03 PM

Memo

0-00-DR-C125_RG_UK.book Page 66 Thursday, September 8, 2011 6:03 PM

Memo

0-00-DR-C125_RG_UK.book Page 67 Thursday, September 8, 2011 6:03 PM

CANON ELECTRONICS INC.

1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN

CANON U.S.A. INC.

ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A.

CANON CANADA INC.

6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA

CANON EUROPA N.V.

BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS

CANON LATIN AMERICA, INC.

703 WATERFORD WAY, SUITE 400 MIAMI, FLORIDA 33126, U.S.A.

CANON AUSTRALIA PTY. LTD.

1 THOMAS HOLT DRIVE, NORTH RYDE, SYDNEY. N.S.W, 2113. AUSTRALIA

CANON SINGAPORE PTE. LTD.

1 HARBOUR FRONT AVENUE #04-01, KEPPEL BAY TOWER, SINGAPORE 098632

CANON HONGKONG COMPANY LTD.

19TH FLOOR, THE METROPOLIS TOWER, 10 METROPOLIS DRIVE, HUNGHOM, KOWLOON, HONG KONG.

CANON KOREA BUSINESS SOLUTIONS INC.

168-12 SAMSEONG-DONG, GANGNAM-GU, SEOUL, KOREA

0-00-DR-C125_RG_UK.book Page 68 Thursday, September 8, 2011 6:03 PM

Canon Imageformula Dr C125 Scanner Quick Reference Guide

Navigation menu

Versions of this User Manual:

Views

Navigation