Canon Multipass Printer C755 Users Manual

Canon-Multipass-C755-Owners-Manual-588987 canon-multipass-c755-owners-manual-588987

c755 280c7b33-091d-440a-9e8a-e228f7b4f8af Canon Fax Machine C755 User Guide |

2015-01-23

: Canon Canon-Multipass-Printer-C755-Users-Manual-241918 canon-multipass-printer-c755-users-manual-241918 canon pdf

Open the PDF directly: View PDF PDF.
Page Count: 7

DownloadCanon Canon-Multipass-Printer-C755-Users-Manual- Canon-multipass-printer-c755-users-manual
Open PDF In BrowserView PDF
1

Unpack the MultiPASS
1

Carefully remove all items from
the box.
Document
Support

3

Open the document tray and remove
the protective sheets.

BCI-3e BJ Tanks (C, M, Y, Bk)
Ink Cartridge
Storage Box

Telephone
Line

Protective Sheets

Power
Cord

BC-33e Color
BJ Cartridge
Document Tray

Output Tray

MultiPASS
C755
Unit

4

Open the operation panel; it only
opens slightly.
Remove the protective sheet from the unit's
Automatic Document Feeder (ADF).

Remove these items from the documentation package:
this Quick Start Guide, the Canon Creative for
MultiPASS CD-ROM, the Stand-alone Fax Manual,
Registration card, and Warranty card.
2

Remove all shipping tape and
materials from the unit.

Press the operation panel closed until it clicks
into place.
5

Tape
(Check all surfaces)
Spacer

Note that tape may not be in the exact locations
shown here.

Open the Automatic Document Feeder
(ADF), and remove any protective
material from the
ADF
cartridge holder.

2

Set Up the MultiPASS
1

Attach the
document
support.

Recommended Device Connections

Receive Modes

MultiPASS and Answering Machine

Ans.Machine

Answering
Machine

Wall Jack

MultiPASS, Answering Machine and Telephone

Wall Jack

2

Attach the
output tray.

Answering
Machine

MultiPASS and PC Modem

Ans.Machine

Telephone

Fax Only
or DRPD
PC

Wall Jack

4

3

USB Cable Users–Do not connect the
cable now.

Connect the
phone line.

Make sure the computer is turned off.

Connect the
telephone line to
the L jack on the
MultiPASS and to
the wall jack.

Connect a USB or parallel cable
to your computer
and then to
the MultiPASS.

To use the MultiPASS for receiving both faxes
and voice calls, you must attach a telephone
and/or answering machine to the
jack on
the unit.
If you use Caller ID with any of these
configurations, place the Caller ID device
between the MultiPASS and the wall jack.
Recommended Device Connections

Receive Modes

MultiPASS Only

Fax Only
or DRPD

Wall Jack

MultiPASS and Telephone

Fax/Tel, DRPD,
or Manual
Telephone

Wall Jack

Connect your computer to
the MultiPASS.

USB connection

5

Parallel cable connection

Connect the power cord to the
MultiPASS and to a wall outlet.
The MultiPASS has no power switch.
The power is on
as long as
the unit is
plugged in.

3

Install the BJ® Cartridge

Spilled ink can stain any surface.
Open BJ cartridges and tanks very carefully.
See your User's Manual for complete details
Caution
on BJ cartridge and tank maintenance.

2

Raise the blue cartridge
lock lever
on the
cartridge
holder.

3

Remove the cartridge from its package,
and remove these protective materials:
Orange cap
Cap
Orange tape

Lock Lever

Make sure the MultiPASS is plugged in.
The LCD reads:

1

Open the ADF.

Tape

Handle

Do Not Touch
these areas

Caution

4

Set the cartridge
into the cartridge
holder.

5

Lower the blue
cartridge lock lever
until it locks into
place.

6

Remove the two
orange pieces.

Do not touch the ribbon cable, the small
circuit board, the guide rail, or the round
shaft. Touching these parts may adversely
affect operation of the unit and/or affect
print quality.

Round Shaft

Guide Rail

Circuit Board
Ribbon Cable

Press in on the
tabs to remove
the pieces.

4

5

Install the BJ Tanks
1

2

Pick up the yellow BJ tank.
Pull up the
orange tape.
Remove the
plastic wrapper
from the tank.

The sheet feeder is the larger capacity tray
behind the ADF.
ADF
(holds documents
to be faxed, copied,
or scanned)

low

Yel

de

Ma
in

SH

an

PU

Jap

Fan a stack of paper. Fan the edge that will feed
into the MultiPASS first; then tap the stack on
a flat surface to even its edges.
Ink

BCI- Ta

2

Yellow
Mad

e in

PUS

H

Japa

n

Insert the stack of paper.
Make sure the print side of the paper is face-up.
Align the right edge of
the stack with the right
side of the sheet feeder.

Ink Tank

Ink Tank

Ink Tank

Ink Tank

BCI-3BK

BCI-3C

BCI-3M

BCI-3Y

Black

Cyan

Magenta

Yellow

Made in Japan

Made in Japan

Made in Japan

Made in Japan

PUSH

PUSH

PUSH

PUSH

Black (BCI-3eBK)
Cyan (BCI-3eC)
Magenta (BCI-3eM)
Yellow (BCI-3eY)

6

Sheet Feeder

PUSH

Press down
on the top of
the BJ tank
until it locks
into place.

Install the other
3 BJ tanks
as shown.

Pull the paper rest up until it stops.
Move the paper guide to the left
to match the size
of your paper.

BC

5

Insert the
yellow BJ
tank into the
right slot of
the cartridge.

1

k
an
InkT I-3M

4

Sheet Feeder
(holds blank paper
for printing or
receiving faxes)

Twist off the orange
protective cap.
To prevent spills,
do not press
the side of
the BJ tank.

3

Load a Stack of Paper

Close the ADF cover.
When the ALARM light stops flashing,
the printer is ready.

No gaps
here

Tab
Paper limit mark

Do not fill the sheet feeder above
the limit mark ( ). The sheet feeder
holds up to 100 sheets of plain
paper (20 lb or 75 g/m2).
Adjust the paper guide snugly against the side
of the stack of paper.

6

Install the MultiPASS Software

Your MultiPASS comes with a Setup program that makes installing the MultiPASS software easy and fast.
You install the MultiPASS software from the Canon Creative for MultiPASS CD-ROM.
Important! The MultiPASS must be plugged in. If you have a previous version of the MultiPASS Desktop Manager
installed, you must remove it. See your MultiPASS Desktop Manager Software Guide for details.
Windows® 2000/NT Users: Administrator Privileges are required to install and remove the MultiPASS
Desktop Manager software.
Stand-alone Fax Users: If you plan to use the MultiPASS as a stand-alone fax machine, see the Stand-alone
Fax Manual for instructions on how to program your name and fax number. Then select your Receive mode
based on how you set up your phone connection in Step 2 .

Start up your system in this order:

Windows 95/98/2000/NT Parallel Cable Users
1. Make sure your computer is turned off.
2. Be sure the MultiPASS is plugged in and connected
to the computer.
3. Make sure the Canon Creative CD is NOT yet
inserted in your CD drive.
4. Now turn on the computer.
5. If any Windows applications start automatically,
close them before you start installation. This is very
important. Make sure NO programs are running,
including any virus protection programs.

Make sure Windows starts.
Click Cancel if you see a screen similar to these:
"New Hardware Found", "Update Device Driver
Wizard", or "Add New Hardware Wizard".
Make sure you return to the Windows desktop.

When you see the Windows desktop, follow
these steps.
1. Insert the Canon Creative CD into your CD drive.
(This CD contains all the device software for your
MultiPASS, including the MultiPASS Printer and
Fax drivers, MultiPASS ODBC, and ScanGear™
for MultiPASS.) Setup starts automatically.
If Setup does not start automatically, from the
taskbar, click Start and then Run. You see the
Run screen.

If anything is displayed in the Open box, replace it
by typing X:\SETUP (where X:is your CD drive).
Then click OK.

2. Follow the on-screen instructions to
finish installation.
Normally you click Next or Finish
to move from one screen to the next.
Be sure to read each screen carefully.
When specifying your fax information,
you must enter a fax heading and
specify a Receive mode. Select your
Receive mode based on how you set
up your phone connection in Step 2 .
When installation is complete, the Setup
program determines whether or not your
computer needs to be restarted.
The next time you start your
computer, you may see the
"New Hardware Found" screen.
Wait a few seconds while the
system updates itself; the screen
will disappear.
The next time you start your system,
double-click on the Canon Creative Launcher
icon on your desktop. From here you can
install the Canon Creative software, run the
software programs after they are installed,
register the MultiPASS, view the online
manuals, and find out how to order supplies
and get help from Canon.

What's Next?
Windows 98—USB Cable Users
1. Make sure the MultiPASS C755 is NOT connected
to your computer.
2. Turn on your computer.
3. Insert the Canon Creative CD into your CD drive.
Setup starts automatically.
4. When prompted, connect the USB cable to your
computer and then to the MultiPASS
(see Step 2 for details).
5. Follow the instructions on each screen
to complete software installation.

Windows 2000—USB Cable Users
1. Make sure the MultiPASS C755 is NOT connected
to your computer.
2. Turn on your computer.
3. Connect the USB cable to your computer and
then to the MultiPASS (see Step 2 for details).
Windows recognizes the new device and starts
Plug & Play for your USB port.
4. Follow the instructions on each screen.
When you see this screen:

After using this Quick Start Guide to unpack and
set up your new MultiPASS unit, you'll want to look
at the rest of your documentation.

MultiPASS C755 User's Manual
(online)
This manual offers detailed information on how
to operate your new MultiPASS. It describes
how to use the MultiPASS as a color printer and
covers the basics on how to send and receive
faxes. It also includes maintenance,
troubleshooting, and specifications.

MultiPASS Desktop Manager
Software Guide (online)
To use the PC faxing and scanning features of
the MultiPASS, you must install the MultiPASS
Desktop Manager software. Then use the online
Software Guide to find out how to use the
MultiPASS Desktop Manager to define and
control all of the features of the MultiPASS.

Stand-alone Fax Manual
(printed)
If you are NOT going to connect the MultiPASS
to your computer, use this manual to find out
how you use the operation panel on the
MultiPASS to control all your faxing and
receiving functions.
The User's Manual and Software Guide are
provided in Adobe® Acrobat® PDF format.
You can access the manuals in one of two ways:

Insert the Canon Creative CD into your CD
drive and wait for the drive to start up.
Make sure CD-ROM drive is checked, and
be sure to uncheck the other options.
Then click Next.
5. Continue to follow the instructions on each
screen to complete software installation.

Double-click the Canon Creative Launcher icon
on your desktop.
Browse the Canon Creative for MultiPASS
CD-ROM from your CD drive.
Next, click the "Manuals, Supplies, and Help"
button. Then click on the button that corresponds
to the manual you want to read. If you do not have
Adobe Acrobat 4.0 loaded on your computer,
simply follow the instructions to load it. (You must
use Adobe Acrobat 4.0; do not use other versions.)
You can also open the manuals from the
MultiPASS program list.

Printing an Image
or Document
To print an image or a document, make sure
you have paper loaded in the sheet feeder (see
Step ). Then simply start the application
program that you used to create the image or
document. With the document open, select the
Print command. (Normally you choose Print or
Print Setup from the File menu.) Make sure the
Canon MultiPASS printer is selected as your
default printer. After specifying any special
printing parameters, select OK to start the print
job. See your online MultiPASS C755 User's
Manual for details.

Copying an Image
or Document
To copy an image or a document, make sure
you have paper loaded in the sheet feeder.
Next, place the image or document you want
to copy face-down in the ADF. On the operation
panel, press the Copy button and then press
the Start button. (To make multiple copies,
press Copy, enter the number of copies with
the numeric buttons, and then press Start.
To make one color copy, press Color so the light
comes on, press Copy, and then press Start.
See your online MultiPASS C755 User's Manual
for details.)
Color/B&W

Faxing or Scanning
an Image or Document

Start

Copy

Numeric
Buttons

For faxing, you load the document face-down in
the Automatic Document Feeder (ADF), dial the
number you are faxing to, and then press the
Start button on the MultiPASS.
For scanning, you load the image or document
face-down in the ADF, then press the Start
button on the MultiPASS.
Start

MultiPASS Hardware Cannot
Initialize
If you see this error message, refer
to the Troubleshooting chapter in
your online MultiPASS C755 User's
Manual for details.

When scanning, the Toolbar will launch on your
Windows desktop:

Now you simply click a button on the Toolbar to
scan a document or image to a particular
destination. See your online MultiPASS Desktop
Manager Software Guide for complete details on
using the Toolbar.
ENERGY STAR® Compliant

©2000 Canon Computer Systems, Inc. Canon, BCI, BJ, BJC, Bubble Jet,
MultiPASS, and ScanGear are trademarks of Canon Inc. All other product
and brand names are trademarks or service marks of their respective
owners. As an Energy Star® Partner, Canon U.S.A., Inc., has determined
that this product meets the Energy Star® guidelines for energy efficiency.
Printed in U.S.A.
CST-5532-000
30-32305
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Modify Date                     : 2000:09:26 09:50:50-07:00
Producer                        : Adobe PDF Library 2.0
Create Date                     : 2000:07:13 10:38:52
Page Count                      : 7
EXIF Metadata provided by EXIF.tools

Navigation menu