Canton Elektronik and KG DM350 Sound bar with Amplifier User Manual DM 90 2 BAL DEF indd

Download:
Mirror Download [FCC.gov]
Document ID	1731016
Application ID	91Nz0YO/Ch8OyqVq4OYYsA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.62kB (432713 bits)
Date Submitted	2012-06-27 00:00:00
Date Available	2012-06-27 00:00:00
Creation Date	2012-05-08 08:49:08
Producing Software	Acrobat Distiller 9.4.6 (Macintosh)
Document Lastmod	2012-06-21 17:24:24
Document Title	DM 90_2 BAL DEF.indd
Document Creator	Adobe InDesign CS5 (7.0.1)
Document Author:	ahennel

Select a base that is as level as possible for your DM System. Make sure the location is dry and clean and away from windows with direct sunlight, heat sources,
vibrations, moisture and extreme cold. When setting it up on a smooth surface you
should use the rubber feet supplied.
Never open the cabinet. If you come across any problems or defects contact your
dealer or a qualified technician.
In order to avoid damaging your DM System it should only be used with the voltage specified on the nameplate.
In order to avoid the risk of fire or electric shocks the DM System should not be
subjected to rain or high humidity (>80%). The equipment complies with the
current EMV regulations at an ambient temperature of + 10°C …+40°C.
Do not apply force to the operating elements, connections or cables. To move the
DM System to another location first unplug the mains cable and then disconnect it
from other devices. Always pull on the plugs rather than the cable. Never touch the
mains cable with wet hands.
In order to prevent the DM System from overheating it should be set up at a
minimum distance of 5 cm from any walls or pieces of furniture. Avoid any heat
accumulation and never cover your DM System with curtains, tablecloths etc.
If the sound reproduction is marred by distortions such as unnatural knocking,
throbbing or high frequency clicking the volume should be turned down immediately.
Do not use any chemical solutions to clean the device. Use a dry, clean cloth.
Extreme changes in temperature can cause condensation to form inside the DM
System. Do not use the device until the moisture has evaporated (at least 2 hours).
The remote control batteries must be disposed of at a proper battery recycling
centre. Batteries should be kept out of reach of children. Batteries must be inserted
the right way up. Only use the batteries specified for use with this system (LR03
AAA 1.5V) or rechargeable batteries. The batteries supplied are not rechargeable
and may therefore not be recharged.
Access to the mains plug should be kept clear at all times so that the device can
be unplugged in case of emergency. For your own safety please unplug the DM
System from the mains if it is likely to be unused for a long period or in the event
of thunderstorms or potential flooding.
The user is responsible for making sure that the device is correctly set up and
correctly connected to the mains. Canton does not accept any liability for damages
or accidents caused by improper set up or connection.
Warning: Listening to music at high volume, in particular over a long period of
time, can damage your hearing.
Do not site your DM System close to heat sources or open flames (e.g. candles).
Do not put anything on top of the cabinet of the DM System or in front of the
bass reflex opening, in particular no containers filled with liquids. Movement and
vibration can lead to objects being damaged.
27
Deutsch
English
Canton does not accept liability for any damages resulting from the non-observance of the following points.
Do not insert any objects or parts of the body into the opening of the cabinet as
live components inside the cabinet may be touched and damaged. This could lead
to short circuits, electric shock or fire.
Français
Please read these instructions carefully and retain them so that you can refer to
them again in future.
Espagnol
Note:
Dear Customer,
Welcome to the Canton family and thank you for the confidence you have shown in us with the purchase of this system. You have selected a high quality loudspeaker system, which shows that you have high standards regarding sound quality and workmanship.
Please read through these instructions carefully before setting up and connecting your DM System. They are designed to help you to get the most out of
your system. The Canton distribution network covers over 40 countries. If you have any questions our team of experienced distributors along with the
authorised dealers will be happy to help you.
We hope that you get many long hours of pleasure and satisfaction from your DM System.
The Canton team
System description
The virtual surround system of the DM Series creates a rich and full sound field that is normally only possible with 5.1 Systems. To achieve this sound
quality the individual channels of a multi-channel recording are put through a special frequency-specific process and mixed onto two channels, which
then creates the impression of surround sound in the room. The result is outstanding listening pleasure for minimum installation costs. The systems have
an integrated, RDS-enabled FM Tuner and adaptive remote control, which can be used to control a second listening zone (Multiroom).
28
Deutsch
Package contents DM 90.2
The Digital Movie System DM 90.2 is supplied with the following components:
English
1) An active Center Surround loudspeaker with integrated audio receiver (including RDS-enabled FM Tuner).
2) A cable set for connecting 3 digital and 2 analog sources.
3) An easy-to-use remote control with display panel.
4) A coaxial cable for connection to a broadband cable network.
5) A power cable for connection to the mains power supply.
6) An aerial for VHF reception.
- Three batteries (LR03 AAA 1.5V) for the remote control
Français
Espagnol
29
Positioning the DM System
The Center Surround loudspeaker DM 90.2 should be positioned above or below the television. A flat screen TV may be placed directly on top of
the DM 90.2. If using a tube TV that may be deeper than the DM System you must be careful to ensure that it is securely placed on the DM 90.2
and is not able to wobble.
Warning: The DM 90.2 can only tolerate weights of up to 80 kg.
30
Operation indicator (red = standby, green = on)
IR receiver
PRE OUT 2.1/5.1 mode preamplifier – output
Power switch
Deutsch
Rear view of the DM 90.2
Screw for earth connection
Espagnol
Français
English
Port only for software updates
Zone 2 / Line – output
FM aerial connection
Subwoofer – output
Digital inputs (optical)
for e.g. SAT, DVD …
Digital inputs (coaxial) for e.g. SAT, DVD …
Power cable socket
Analog inputs for TV, VCR, record player …
31
Connecting the DM 90.2
The Line 2 / Phono input allows you to connect either a line-level audio source (up to 2V) or a record player (up to 5mV). This can be done
by selecting the relevant set up in the system menu.
There is no need to connect up the individual “loudspeakers”
with the DM 90.2 as all the wiring is internal.
Connecting the source devices
The Pre (2.1/5.1 Mode) output allows you to connect, for example,
active wireless loudspeakers. According to the set up selected in the
System Menu (Factory Set / Gerätenamen) the output will be through
the front channels in 2.1 Mode or the surround loudspeakers in 4.1
Mode.
The Canton DM System offer a wide range of connection
options for almost all popular source devices, such as DVD
players, video recorders, satellite receivers, multi-media consoles (Playstation®, X-Box®, …) etc. The audio connections
for your source devices need to be connected to the corresponding ports on the back of the DM 90.2. Source devices
that have a digital output for Dolby Digital and DTS Bitstream
should be connected digitally to the DM System. This ensures
full Dolby Digital and DTS sound quality.
The Zone 2 /Line output has a number of output options, which can
be selected in the System Menu of the remote control:
- Zone 2 with individually adjustable volume for connection to an
active Multiroom or wireless loudspeaker system.
- Line with fixed volume for connection to a recording device, etc …
The video signal connections are made directly between
the source devices and the image display device. The image
source to be used is selected directly from the menu of the
image display device.
Warning: In order to play 5.1 multi-channel recordings (Dolby Digital
or DTS) via the ZONE 2/LINE OUT the “dynamic” setting in the
System Menu should be set to “comp”. For normal playback we
recommend that you use the “full” setting (see page 40).
In order to use the integrated FM Tuner of the DM System
you need to connect the aerial supplied to the appropriate
socket on the DM 90.2. Better reception will be achieved if
the aerial is extended. For optimal reception we recommend
connection to a broadband cable network or a roof-mounted
aerial using the coaxial cable supplied.
In order to use Dolby Digital/DTS signals (Bitstream) via Zone 2 you
need to select Zone 1 (Main listening zone) as the input.
The Sub output allows an active subwoofer to be connected. This
needs to be activated in the System Menu (see page 17). If the Sub
output is activated the internal subwoofer of the DM System goes
through the high pass filter while the external subwoofer goes through
the low pass filter at 80Hz.
Before you can start using the DM 90.2 for sound reproduction you need to go through the initial installation process
and assign the inputs to the source devices. You will be asked
to do this automatically when you first switch on the device
(see page 12).
32
Mute key
On/Standby key
Function keys, menu-dependent functions
Deutsch
Remote control
Selected source
Personal settings ()
Selected volume
Playback mode
Decoder mode
English
Sources selected using the function keys
OK key
Scroll key
Device selection key
Volume keys
Programme keys (only IR mode)
Menu key
Exit key
Number keys
Number keys
33
Espagnol
Function keys, menu-dependent functions
Français
Modes and  selected using the function keys
Setting up the remote control
Insert the batteries supplied into the remote control. Be careful to insert them the correct way up according to the polarity markings (+/-).
Using the remote control
When all devices are connected to each other and the power has been switched on the
Canton DM goes into Standby mode. Press any key to activate the remote control. If
the remote control is not used for longer than 30 seconds it goes into idle mode. Press
any key to reactivate it.
Note: When the device is turned on for the first time it starts the initial installation
process automatically (see page 36).
If the display shows “keine Verbindung” then there is no radio connection between
the remote control and the DM System. Check that the DM System is switched on
and connected to the mains power supply or reduce the distance between the remote
control and the DM System.
Operating the DM System
Press
to start the DM System.
If you want to turn the DM System off again press
again. The DM System will go back into Standby
mode.
Note: If the DM System is disconnected from the mains power supply when it is still switched on it will automatically go back into an active state
when it is reconnected to the mains power supply (e.g. via a master or slave multiple socket lead).
34
Deutsch
Initial installation
To get to the input configuration press
English
Before you can use the DM 90.2 you need
to assign the inputs to the connected source
devices. You will be asked to do this when
you first switch the device on.
Français
Use the “<” and “>” arrow keys to choose
names for the connected devices. You must
confirm these by pressing “OK”.
To exit the input config menu press
to save all the entries. Then press
to
end the initial installation and return to the
main menu.
Espagnol
Warning: The arrow keys
and
may
not be used when assigning the inputs.
Inputs that are defined as “not active” are
not shown in the main menu.
35
Main menu
The remote control supplied has 8 function keys that
can be used in different ways for different operating
modes. The upper and lower sections of the display
show the functions of each key.
The sources can be selected using the (upper) function
keys lying directly above them. If you have more than 3
sources you can use
to scroll on to the next page
and back.
The Volume (V+/-) can be used to adjust the volume of
the DM System in all menus (even when controlling IR
devices) over 100 levels from 0 to 99.
Mute turns the volume off or on.
With  you can select one of the registered RF devices or a
programmed IR device. If more than 8 devices have been registered/
programmed you can use
to scroll to the devices that are not
currently displayed.
36
Deutsch
In order to allow for the different recording philosophies that are present in music recordings we have implemented two surround modes. Use
“surround 2”, above all in cases of poor intelligibility (e.g. if the voice reproduction is unusually flat and incomprehensible).
English
With
you select whether the playback should be in one of the two stereo or surround modes. In addition to the “conventional” Stereo
mode the DM System also offers a Wide mode with virtually extended stereo base.
The following decoder modes are possible:
Dolby 5.1
DTS
Dolby 2.0
Analog
Virtual Dolby PLII
PCM
Virtual Dolby PLII
Dolby Digital 2.0
Virtual Dolby Digital 2.0 PLII
Dolby Digital
Virtual Dolby Digital
DTX
Virtual DTS
37
Espagnol
PCM (digital)
Stereo
Surround
Stereo
Surround
Stereo
Surround
Stereo
Surround
Stereo
Surround
Analog
Français
The system automatically adjusts to the appropriate decoder
mode according to the input signal.
Tuner
The Canton DM 90.2 has an integrated FM Tuner (VHF) with RDS function. This can be selected using the function keys (radio) in the main menu
of the remote control. There you can make the following adjustments:
The automatic search is activated by pressing and holding (>2 sec.) the “<” or “>” arrow keys (to search backwards or forwards). During the search
process the word “Seek” will appear in the display. The DM System stops automatically at every station with a sufficiently strong signal.
The manual search is controlled by pressing on the “<” or “>” keys. This function can be used to fine-tune a radio station or to search manually for
stations with a weaker signal.
Reduction of hissing in stereo reproduction
The DM System automatically uses stereo or mono reproduction depending on the strength of the signal. If you find a stereo reproduction has too
much hissing you can use the
function key to change it to mono reproduction and reduce the hissing.
Stereo
Mono
Saving a radio station
To save a radio station in a programme slot press
and the programme slot number will start to flash. Use arrow keys
and
to select
from among 50 programme slots. Alternatively you can use the number keys to enter the programme slot number directly. After 5 seconds with no
keys pressed the radio station will be saved in the programme slot shown on the display and the programme slot number will stop flashing.
Note: The station name, transmitted via RDS, (e.g. HR 1, BR 2, SWR 3, …) will only appear upon selecting a saved radio station if the name
appeared on the display at the point of pressing the OK key (the starting point of the saving process).
Selecting a saved radio station
Use the arrow keys
and
directly.
to select a programme slot. Alternatively you can use the number keys to enter the programme slot number
38
to exit the Settings Menu from almost all sub-menus.
will just take you back one menu level.
Settings Menu
In the Settings Menu you can choose between the “Loudspeaker Menu” and the “System Menu”. On the next page you will find an overview of the
menus. A more detailed description can be found on the website www.canton.de.
39
Espagnol
Note: Basically you can use
Français
English
Once your DM System is successfully connected and operational you have the option of setting various parameters. If you want to make any adjustments to the settings of the DM System just turn it on and press and hold
(longer than 3 sec.). To exit the Settings Menu press
again
or use
Deutsch
Optional settings of the DM System
Loudspeaker Menu
In the Loudspeaker Menu the following parameters can be set to adjust the DM System to the room:
Personal values
To save all settings set in the loudspeaker menu up to 6 memory cells ()
Volume adjustment
To adjust the volume level of the individual channels (front left and right, subwoofer, …)
Distance
To balance out different distances between the loudspeakers and the listening spot
Sound
To adjust the treble and bass sounds to the room and according to personal taste
Bass expand
For the automatic volume-dependent adjustment of the bass volume level
Room adjust
Various parametric equalisers are available to balance out ambient factors
System Menu
In the System Menu the following parameters can be set:
Output config
To set the parameters for the Zone 2 /Line output
Sub output
To activate or deactivate the subwoofer output
Input config
To activate and name the 6 signal inputs (see the chapter “Initial installation”)
IR programming
To programme various remote operations (DVD player, TV, …, see the chapter “Learn Menu”)
Lip sync
To synchronise the sound with time-delayed TV images
Dynamics
To adjust the signal compression in the playback of multi-channel signals
Factory Set
The following parameters can be set using Factory Set:
Switch-on volume
Max. volume
Device name
Language
Line 2 config
Factory setting
Firmware
Contrast
To limit the maximum switch-on volume
To establish the maximum volume possible
To select the device configuration (2.1 Mode or 5.1 Mode …)
To select German or English
To select Line Level Input or Phono Level Input
To return the DM System to the factory setting it was supplied with
To display the software versions (DM, tuner and remote control)
To adjust the contrast settings of the display
40
and
at the same time brings you to the “Learn Menu”, where you can lern infrared-controlled devices and register other DM
If the programming has been successful you will see the message “Programming successful”.
Repeat the process until all desired functions have been transferred. Press
previous menu.
to return to the
If the transfer of the remote control data is unsuccessful the message “Programming failed” will
appear for approx. 5 seconds. After that the previous menu will be displayed and you can either repeat
the programming or abort the process.
41
Espagnol
Once you have selected the source with the function to be programmed and confirmed your selection using
you will see the message
“press remote button”. Position the original remote control (e.g. from your DVD player) opposite the one from your DM System (approx. 5 cm
distance). On the original remote control briefly press the key with the function to be programmed and wait until the process has been confirmed
on the display.
Français
English
Pressing
Systems.
Deutsch
Learn Menu
Deleting source devices
In order to totally delete a programmed device use the “Clear” function. After pressing this function you will be asked if you really want
to delete the device. Confirm this by pressing the “yes” function key.
To abort the process press “no”. The remote control will then return to
the Device Selection Menu. Use
to enter the “Learn Menu”. To
leave programming mode press
again.
Renaming the source devices
If you want to rename a source device you can select a description
from a comprehensive list of pre-programmed device names. Follow
the steps described above.
Programming the main keys
The DM System has 5 main keys (Programme +/-, Volume +/- and Mute), which can be allocated to the IR codes of other infrared-controlled
devices. Follow the steps shown above.
Warning: The Volume +/- and Mute keys can only be used for infrared-controlled devices if no DM System has been registered. The volume control
of the DM System will take priority over all other IR devices.
42
To register the remote control on a (further) DM System open the Programme Menu by pressing
simultaneously. Select “RF Learn”
. Select “new device” to register a DM System on the remote control. After confirmation you will be asked to connect
the DM System to be programmed to the mains power supply and to switch it on. Before doing this you should ensure that the DM System had been
disconnected from the mains power supply for at least 1 minute. The remote control will now try to connect with the newly activated DM System. A
successful connection will be shown in the display as “Installation successful”, while failure will bring the message “Installation failed”. If the connection has failed you should identify the problem (device not switched on, distance too great, DM System not disconnected from the mains power supply
English
and confirm this with
and
Deutsch
Register your remote control with a DM System
90) more than once the remote control will automatically allocate it a subscript (e.g. DM90.1, DM 90.2 …). You can then exit the “RF-Learn” menu by
pressing
twice.
If you wish to overwrite an existing DM System, instead of selecting “new device” you should select the system you wish to replace and confirm your
. Select the “Learn” function to proceed. Confirm the overwriting with the “yes” function key or abort the process with “no”.
Espagnol
selection with
Continue as previously described under “new device”.
De-register your remote control from a DM System
To de-register your remote control from a DM System open the Programme Menu by pressing the
and confirm with
Français
for long enough, etc) and start the process again. After successful installation you must enter a name for the DM System. If you enter a name (e.g. DM
. Select the system you wish to “delete” and confirm your selection with
and
continue. Complete the de-registration process by pressing the “yes” function key or abort the process with “no”.
43
simultaneously, select “RF Learn”
. Select and confirm the “Clear” function to
Troubleshooting and Optimisation
Remote control (abbreviation: RC)
Description of problem
Possible cause(s)
Solution
The RC display is blank
1. The RC is in idle mode
2. The batteries are missing or wrongly inserted
3. The batteries are “empty”
1. Press any key to activate the RC
2. Insert the batteries correctly (+/-)
3. Insert new batteries correctly (+/-) or charge rechargeable
batteries
The RC keeps showing “Welcome CANTON”, “Good bye
CANTON” or “please wait”
1. The RC processor has crashed
1. Remove a battery from the RC for min. 30 minutes then reinsert correctly
2. Switch the DM System off at the mains for min. 30 minutes
then switch it back on
2. The DM System processor has crashed
The RC shows “no connection”
1. The DM System is not ready
2. The distance between the DM System and the RC is too great
3. The DM System processor or the RC processor has crashed
4. The RC is not registered with the DM System
1. Connect the DM System to the mains power supply and / or
switch it “ON”
2. Reduce the distance to less than 10 m
3. Turn the DM System off at the mains for min. 30 minutes
then turn it back on and / or remove a battery from the RC
for min. 30 minutes then re-insert correctly
4. Register the DM System following the instructions on page
43 (Register your Remote Control with a DM System)
Display on the RC is hard to read
1. Poor contrast setting
1. Press the “0” and “4” keys simultaneously until “kontrast
xx” is displayed and use “<” or “>” to adjust the contrast.
Press “exit” to close the window
The display is in the “wrong” language
(German and English are the 2 options)
1. The display language of the RC has been switched
1. Press the “5” and “9” keys simultaneously until “language”
is displayed and use the function keys to select the desired
language (display)
2. In the “System Menu” (m = > System Menu => factory set
=> language) select the desired language
2. The language of the DM System has been switched
The RC jumps from IR mode into DM System mode
1. The batteries are almost “empty”
1. Insert new batteries correctly (+/-) or charge rechargeable
batteries
In IR mode commands are carried out 2x
1. When programming the code the key on the original RC was
pressed for too long
2. The key on the DM – RC was pressed for too long
1. When programming the function only press the key on the
original RC for a (very) short time
2. Only press the key on the DM – RC for a very short time
IR device is not operating (correctly)
1. The device has not been correctly programmed
1. Repeat the programming process for the Canton RC with the
original RC of the IR device
2. Ensure a distance of approx. 5 cm between the RCs when
programming
3. Due to the wide range of devices on the market it can
happen that codes cannot be programmed. Unfortunately
this problem has no solution
2. The distance between the RCs was too great / too short
3. The code of the original RC cannot be programmed
44
2. During the configuration process the “up” or “down” arrow
keys and / or the “exit” key were used
DM System does not recognise Dolby Digital or DTS data stream
1. The source is only connected to the analog port (Line 1 or 2)
2. The wrong settings have been selected on the source device
No signal from Zone2 / Line - Output
1. There should be a multi-channel signal from Zone2 / Line
2. The volume for Zone2 is set too low
1. Connect a digital output from the source device to Opt 1 / 2
or Coax 1 /2
2. Select “Bitstream” or “Raw” as the data format on the
source device (referring to the instructions given for the
source device)
1. Set “dynamic” (m => System Setup => Dynamic) to „comp“,
under “Output Config” (m => System Setup => Output
Config => Input) select “zone 1” as the input and on the
main screen select the desired source as input
2. Increase the volume for Zone2 – output under “Volume”
(m => System Setup => Output Config => Volume)
RC only displays “surround” instead of “surround 1” and
“surround 2”
1. The DM System has been set to 4.1 or 5.1 mode
1. Set the system to 2.1 mode under “system preset” (m =>
System Setup => factory setup => System Preset)
Distorted radio reception
1. Poor aerial position
1. Arrange the extended (!) aerial as openly as possibly, well
away from metal surfaces
2. Use a roof-mounted aerial or a broadband cable connection
3. Tune the station manually, following the instructions on
page 39
2. Poor geographical location
3. The station has not been properly set
A set radio station is no longer available once the system has
been switched off and on again (display back on 87.50)
1. The station was not allocated a programme slot
1. Simply press the “OK” key to save a station in Programme
Slot 1
Sound and image are not (lip)synched
1. Long processing times in the TV delay the image
1. Delay the sound in “lip sync” (m => System Menu => lip
sync) so that the image and sound are synchronised (simulta
neous)
45
Deutsch
1. Register the relevant inputs in the “input config” menu
(m => System Setup => input config). Follow the exact
instructions on page 36!
2. Register the relevant inputs in the “Eingangskonfig” menu
(m => System Menu => Eingangskonfig) and only use the
correct keys (see page 36)
English
1. No inputs have been registered in the “input config” menu
(e.g. initial installation was terminated with “exit”)
Français
No inputs except “radio” can be selected
Espagnol
DM System – Functions
DM System -> Volume
No (music) playback
1. The DM System is switched off or in Standby mode
2. The volume is set low or on mute
3. The wrong input has been selected
4. The signal (data stream) from the source has not been
recognised by the DM System
5. Wrong setting of Line2 / Phono input when using a
record player
1. Switch the DM System on so that the RC displays the main
screen
2. Use Volume + (V+) to increase the volume
3. Select the input that is connected to the relevant source
4. Set the source to a different data format or select another
audio format during playback (referring to the instructions of
the source device)
5. Set Line 2 / Phono – Input “line2 config” to “phono” (m
=>System Setup => factory set => line2 config)
Volume will not go above a certain value ( System Setup => factory set =>
max volume) to the desired value (max. 99)
DM System is quieter when switched on than when switched off
1. The “start volume” is set to a value that is lower than
the volume set before switching off
1. Set the “start volume” (m => System Setup => factory
set => start volume) to the desired value (max. 99 but
not higher than “max volume”)
The balance is wrong (location is not central)
1. The volume adjustment of the satellite speakers is wrongly set
or the listening spot is not central
1. In the Loudspeaker Menu use (m => Speaker Setup =>
Level Trim) to set the correct volume levels and (m =>
Speaker Setup => Speaker Distance) to set the correct
distances
1. The Play Mode is set on “stereo” or “wide”
2. The listening spot is not central enough
1. Set Play Modes to “surround 1” or “surround 2”
2. In the Loudspeaker Menu use (m => Speaker Setup =>
Level Trim) to set the correct volume levels and
(m => Speaker Setup => Speaker Distance) to set the correct
distances to the listening spot
3. To achieve optimal sound in the room the DM System
requires a multi-channel data stream. In this case the RC
displays “virtual Dolby Digital” or “virtual DTS”. All other
displays (e.g. “Virtual Dolby PLII) mean that it is not a multichannel data stream, which leads to less of a surround sound
impression
4. Set the system to a 2.1 Mode with virtual surround-mode at
“System Preset” (m => System Setup => factory setup =>
System Preset)
DM System – Sound
In Surround Mode there is little or no surround sound
3. The source only supplies a 2-channel signal
4. The DM System is set to 4.1/5.1 mode
46
1. Set “Bass expand” (m => Speaker Setup => Bass
expand) to “low” or “high”
2. Deactivate the output for an external subwoofer at “Sub
Output” (m => System Menu => Sub Output) or connect it
to an operational external subwoofer using Sub-Out
3. Where possible, set up the system in a different position (e.g.
closer to the wall)
4. Correct or delete the settings for the room adjustment (m =>
Speaker Menü => Room Comp => subwoofer)
2. The output for an external subwoofer is activated but no
subwoofer has been connected or is operating
3. The DM System is in a poor acoustic location
4. Equalisers have been set in the “Room Comp” menu
(volume level increase)
The DM System has too much low bass
1. Listening at a high volume and activating the “Bass expand”
2. Using an external subwoofer with too high a level
3. The DM System is in a poor acoustic location
4. Equalisers have been set in the “Room Comp” menu
(volume level increase)
The DM System has too little top bass
1. The DM System is in a poor acoustic location
2. Equalisers have been set in the “Room Comp” menu
(volume level increase)
3. The bass level in the “Tone Control” menu is set to neutral
or reduced
4. Use of an external subwoofer with the wrong phasing (phase
adjustment) between internal and external subwoofers
47
1. Set “Bass expand” (m => Speaker Setup => Bass
expand) to “low” or “off”
2. Adjust the external subwoofer (to a lower level)
3. Where possible, set up the system in a different position (e.g.
closer to the wall)
4. Correct or delete the settings for the room adjustment (m =>
Speaker Menü => Room Comp => subwoofer)
1. Where possible, set up the system in a different position (e.g.
closer to the wall)
2. Correct or delete the settings for the room adjustment (m =>
Speaker Menü => Room Comp => subwoofer)
3. Increase the bass level in the Sound Regulation menu (m =>
Speaker Menü => Tone Control => Bass)
4. Correct the phasing on the external subwoofer to suit the
DM internal subwoofer or change the position of the
external subwoofer
Deutsch
1. Listening at a (very) low volume
2. Set the system to a 2.1 or 4.1 Mode at “System Preset”
(m => System Setup => factory setup => System Preset)
English
1. Select “surround 2“ as Play Mode
Français
The DM System has little or no low bass
1. During recording (BD or DVD) the voices were mixed
between the right and left channels
2. The DM System is in 5.1 mode
Espagnol
In Surround Mode the voices are hard to understand
The DM System has too much upper bass
1. The DM System is in a poor acoustic location
2. Equalisers have been set in the “Room Comp” menu
(volume level increase)
3. The bass level in the “Tone Control” menu is neutral or
1. Where possible, set up the system in a different position (e.g.
closer to the wall)
2. Correct or delete the settings for the room adjustment (m =>
Speaker Menü => Room Comp => subwoofer)
3. Decrease the bass – level in the Sound Regulation menu
(m => Speaker Menü => Tone Control => Bass)
The DM System has too little or too much level in the
whole bass range
1. The volume level adjustment for the subwoofer is set wrong
The DM System sounds “flat” (too little treble)
1. The listening area has severely dampened acoustics or the treble 1. Increase the treble setting in the sound settings menu (m =>
sound setting is set very low
Speaker Menü => Tone Control => treble )
2. A pure stereo signal is being played in one of the surround modes 2. Set the DM System to stereo play mode
3. Equalisers have been set in the “Room Comp” menu
3. Correct or delete the settings for the room adjustment (m =>
(volume level increase)
Speaker Menü => Room Comp => front)
The DM System sounds sharp or aggressive (too much treble)
1. The listening area is acoustically hard (less dampened) or the
treble sound setting is too high
2. Equalisers have been set in the “Room Comp” menu
(volume level increase)
1. Decrease the treble setting in the sound settings menu (m =>
Speaker Menü => Tone Control => treble)
2. Correct or delete the settings for the room adjustment (m =>
Speaker Menü => Room Comp => front)
The sound signal sounds (very) distorted
1. Listening at very high volume, which leads to overmodulation
of the DM System
2. Use of an analog input with a signal level that is too high (level
of the source is higher than 2Veff)
3. Use of Line2 / Phono input with a Line-level source and the
“Phono” setting
4. Use of Zone2 – Output to operate an external device with a
level that is set too high
1. Immediately reduce the volume (also to avoid damaging the
device)
2. Decrease the level of the source if this has a volume control
5. With multi-channel recordings it is theoretically possible that
the signal processor of the DM System will be overmodulated
48
1. In the Speaker Menu (m => Speaker Menu =>
Level Trim =>subwoofer) set the desired volume level
for the subwoofer
3. Set the Line 2 /Phono – Input to “line” at “line2 config” (m
=> System Setup => factory set => line2 config)
4. Reduce the volume for the Zone2 – Output using the Volume
menu (m => System Setup => Output Config =>
zone2 vol)
5. Set the “dynamic” to “comp” (m => System Setup =>
dynamic)
In order to ensure that your Canton loudspeakers continue to give you
pleasure for a long time please follow these care instructions: Never
expose the loudspeaker cabinet to direct sunlight. Avoid extremes of
temperature and protect your loudspeaker from humidity. Do not clean
the surface of the cabinet with alcoholic or abrasive cleaning agents. Use
of a lint-free cloth is recommended.
A loudspeaker needs a play-in time of approx. 15 – 20 operating hours
to develop its full performance potential. During this time the properties
of all the mechanical parts alter until they reach the values laid down in
the design of the loudspeaker, i.e. the chassis suspension becomes more
flexible and the playback quality improves.
Deutsch
Play-in time
Espagnol
Français
English
General maintenance advice
49
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to
operate this equipment. (Example- use only shielded interface cables when connecting
to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user
authority to operate the equipment.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-701
Modify Date                     : 2012:06:21 17:24:24+08:00
Create Date                     : 2012:05:08 08:49:08+08:00
Metadata Date                   : 2012:06:21 17:24:24+08:00
Creator Tool                    : Adobe InDesign CS5 (7.0.1)
Format                          : application/pdf
Title                           : DM 90_2 BAL DEF.indd
Creator                         : ahennel
Document ID                     : uuid:936d6f80-8482-49f4-a39d-d1b82197792d
Instance ID                     : uuid:fdfd5d51-ebf6-4983-8409-cf267d2cdb6e
Producer                        : Acrobat Distiller 9.4.6 (Macintosh)
Page Count                      : 24
Author                          : ahennel

EXIF Metadata provided by EXIF.tools
FCC ID Filing: WHZ-DM350

				
				

							
		
		

			
Navigation menu