Capital Prospect 4BXT Remote Control Transmitter User Manual m4B103fcc

Download:
Mirror Download [FCC.gov]
Document ID	1336131
Application ID	zujLZ4teyFzsbzoHxpDNUQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.61kB (170143 bits)
Date Submitted	2010-09-01 00:00:00
Date Available	2010-09-02 00:00:00
Creation Date	2010-08-24 10:04:16
Producing Software	Corel PDF Engine Version 9.337
Document Lastmod	2010-08-24 14:31:00
Document Title	m4B103fcc
Document Creator	CorelDRAW Version 9.337
Document Author:	Ida

Model 4B-101,
4B-201, 4B-103,
4B-434
4-Button Remote Control
1. INTRODUCTION
3. OPERATION
The Remote Control allows you to operate the MA Series control panel
remotely with a press of a button. You can arm the system, disarm the
system and activate the alarm instantly.
The remote control can be used to arm, disarm, activate the alarm instantly.
ARM AWAY
In this package, you should find a remote control, with a 12V alkaline
battery installed.
Remote
Control
12V Lithium
battery
Please follow the instructions below to program the remote control to the
MA Series control panel.
2. LEARN REMOTE CONTROL TO MA SERIES CONTROL PANEL
In order for the remote control to communicate with the control panel
properly, the remote control must be programmed to the control panel.
Follow the brief instructions below or refer to the detail instructions from
the MA Series User’s Instructions to program the remote control to the
control panel.
Press 3 sec.
Long Beep
OFF CHIME ALERT
LEARN
MUTE
INPUT DC 12V
Step 1:
Press and hold the Learn Button on the Control Panel for 3 seconds.
Control Panel beeps once and you may release the Learn Button.
PANIC
DISARM
ARM HOME
Arm Away - Pressing the Arm Away button on the keychain remote will
arm the system in Away mode, which will result in a 45-second exit delay.
Arm LED will flash.
Arm Home - Pressing the Arm Home button on the keychain will arm the
system in Home mode. Arm LED will be steadily on instantly.
Disarm - Pressing the disarm button on the keychain remote will disarm
the system instantly. Arm LED will also be off.
Panic - Pressing the panic button will cause the siren to sound instantly.
4. BATTERY REPLACEMENT
The battery of the keychain remote (Alkaline, Type 23A, 12V) needs to be
replaced when either one of the followings occurs:
1. The LED on the keychain doesn’t flash or on when a key is pressed; or
2. The operating range starts to decrease.
To replace the battery:
1. Undo the two screws on the back of the transmitter.
The bottom case will then come off.
2. Using a small screwdriver or pen, pry out
the old battery from one end.
3. Place the new battery in position. A diagram
in the battery compartment indicates which
end is positive and which is negative.
4. Close the battery cover and reinsert two screws.
Step 2:
Press the zone button (1, 2, 3, or 4) once, for which you want to program
the remote control to. The selected Zone LED will flash.
5. OTHER MA SERIES ACCESSORIES
The MA Series control panel can work with different accessories include:
Motion Sensor, Door/Window Sensor, Flood Sensor, External Keypad,
Audio Alarm, Emergency Dialer, etc. Please visit www.skylinkhome.com
or contact us at support@skylinkhome.com for more information of how
to fully utilize your Wireless Alarm System - MA Series.
6. FCC
Zone LED flashing
Press the zone button
Step 3:
Activate the Remote Control by pressing the red Panic Button.
Press Button
Control Panel long beep
Zone LED flashing OFF
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Step 4:
You will hear a long beep and the zone LED stops flashing. The remote
control is now programmed to the Control Panel.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
7. CE
Note:
You may program 1 remote control to one zone.
If you have multiple remote controls, you need to program them into
different zones. (one per zone)
Declaration of Conformity
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 301489-3, EN300220-3, EN60950-1, EN50371. This equipment
conforms to the essential requirement of the Directive (1999/5/EC) of the European
Parliament and of the Council.
8. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
9. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work
or download latest information and user manual, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com
CUSTOMER SERVICE
Rm 1303, Block B, Veristrong Industrial Centre,
36 Aupuiwan Street, Fotan, N.T. Hong Kong.
Email:sales@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z706
©2009 SKYLINK GROUP

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Author                          : Ida
Create Date                     : 2010:08:24 10:04:16Z
Modify Date                     : 2010:08:24 14:31:00+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Ida
Title                           : m4B103fcc
Creator Tool                    : CorelDRAW Version 9.337
Metadata Date                   : 2010:08:24 14:31+08:00
Producer                        : Corel PDF Engine Version 9.337
Document ID                     : uuid:7d379d3f-4f78-49a0-b38d-df65875d3041
Instance ID                     : uuid:6a64e938-4496-424d-82a9-3a214d965223
Page Count                      : 2

EXIF Metadata provided by EXIF.tools