Capital Prospect 89 Remote Keypad (Transmitter) User Manual 38imefs1

Capital Prospect Ltd Remote Keypad (Transmitter) 38imefs1

User Manual

1a. Locate frequency switch on the top of the transmitter: (See diagram A)1b. Determine the brand of your garage door openerand set the frequency switch to the correspondingposition. (See chart 1)Diagram ASTEP 1 - SET FREQUENCY SWITCHSTEP 2 - SET BRAND JUMPERSPROGRAMMING THE TRANSMITTERA = “+” B = “-”Diagram BABCDStep 1FrequencySwitchStep 2Brand JumpersStep 3Code SettingBrand JumperABCDREMOVE JUMPER = “0”Thank you for your purchase of the Skylink garage door remotecontrol, Model 89. There are 3 different steps you need to setup inorder to use this universal garage door remote control to operateyour existing garage door opener. These 3 steps are:1) Frequency switch – select the correct frequency according tothe brand of your existing garage door opener.2) Brand jumpers – place the brand jumpers at the correct posi-tion according to the brand of your existing garage door opener.3) Code setting – Set the DIP switch on the Model 89 so that theymatch the code setting of your existing garage door opener.Please follow the detailed instructions below in order to setup theSkylink Model 89 to work with your existing opener. If your existinggarage door remote control does not have any DIP switches forcode setting, then you can skip Step 3, i.e. no need to change thecode setting of the DIP switch on the Model 89.Chart 1Chamberlain®Lift-Master®Sears®Wayne Dalton®Master Mechanic®Genie®Overhead®Pulsar/Allister/Allstar®Linear® MegaCodeTMLinear®M-O-M®Stanley®Multi-Code®Martec/Teckey®Skylink® UR-100390390390300/390390390390318318310310310300/310300390Brand of your opener Set switchto position FrequencyUSADDDA/DDDDCCBBBA/BADUSACANADAA300310B310315C318318D390390Set switchto position FrequencyCANADAB/DB/DB/DB/DB/DB/DDCCAAAA-D315/390315/390315/390315/390315/390315/390390318318310310310310-390Group Brand Brand jumpers setting A B 1 Stanley®, Multi-Code®, Martec® - - 2 Linear®, Moore-O-Matic® + 0 3 Pulsar®, Allstar®, Allister®, Linear® MegaCode TM - 0Skylink® UR-100 4 Chamberlain®, Lift-Master®, Sears®, Wayne Dalton®, + -Master Mechanic® (with DIP switches) Genie® IntellicodeTM * 5 Genie® (with DIP switches), Overhead® 0 + 6 Chamberlain®, Lift-Master®, Sears®, Wayne Dalton®, 0 -Master Mechanic® (without DIP switches but withyellow, white, or gray learn button) 7* Genie® IntellicodeTM* + + 8 Chamberlain® ,“Security +”TM, Sears®, Lift-Master® - +(without DIP switches but with red, orange or greenlearn button) Chart 2* Note: If your existing garage door opener belongs to Genie® IntellicodeTM , please use setting for Group 7 unless this setting cannot operate your garage door opener properly, then use setting for Group 4.3c. If your existing transmitter or receiver has fewer than12 switches, matchonly the first corresponding DIP switch. Leave the remaining posts incenter position “0”.3d. Enter the current 4-digit PIN, on the keypad of the Model 89, then press[#] will activate the garage door opener. If you have just purchased theModel 89, the factory default4-digit PIN is 0000. So pleaseenter [0], [0], [0], [0], [#]. If thegarage door does not open,reverse all of the DIP switchon the model 89. The “ + ”will be changed to the “ - “position and the “ - ”positionwill be changed to the “ + ”position (see diagram F). Alsotry the unused DIP switches inthe “ + ”, “ 0 ” or “ - ” positions.STEP 3 - SET DIP SWITCHESNOTE: The backlight comes onand a beep is emitted when anykey is pressed. The backlight ofthe key pad may not be visiblewhen it is too bright outside.When any key is pressed, thenext key must be pressed within5 seconds or the backlight turnsoff and the sequence is canceled.You must begin again.If the keypad does not emit abeep when pressed,wait a fewseconds and press the key again.If you hear a beep, the keypadhas accepted that key. - OperationPress [ PIN ] , [#]To open or close garagedoor, press your four digitPIN and the [#] key. Ifconfirmed, the model 89will emit three beeps. - To change your PIN:1. Enter the current PIN,(currently set at 0 0 0 0),press ,2. Enter new 4 digit PIN,press ,3. Enter new PIN again,press .For example, if you arechanging the PIN numberfrom 0000 to 1234, enterthe following sequence,0000, ,1234, ,1234, .If confirmed, the backlitLED flashes and the unitemits a long beep.*Two 3 volt Lithium type(CR2032) batteries(included).+-It is time to change thebatteries when the backlightno longer appears.BatteryCompartmentBATTERY***KEY PAD OPERATION WARNINGIf this transmitter triggersother garage doors inyour neighborhood,change all your trans-mitters and receiver to anew code setting.DO NOT let children usethe garage door trans-mitter without adultsupervision. Childrencan injure themselves orothers by the garagedoor.If you do not hear 3 beepsafter the 4-digit PIN and[#] is entered, that meansyou have entered anincorrect PIN, and theModel 89 will not operateyour garage door.**Original PositionReversed PositionDiagram F-Position the keypad on the garage door frame.-Lift up the cover and insert screw above the keypad in the slot provided (a).-Remove the battery cover and insert the second screw in the lower slot (b).-Replace the battery cover and insert screw (c). (a) (c) (b)INSTALLATIONSKYLINKTECHNOLOGIES INC.2213 Dunwin DriveMississauga, Ontario,L5L 1X1, CANADA(905)608-9223(905)608-8744 FAXEmail:support@skylinkhome.com (Reply within 24 hrs)Customer Service : (800)304-1187From 9am to 5pm EST (Mon-Fri)http://www.skylinkhome.comP/N. 101A162-X Rev.XPatent no. 5680134, 6005508Patents Pending©2002 SKYLINK TECHNOLOGIES INC.Skylink will not be heldliable or responsible forany misuse or applicationof this product other thanfor its intended use.® are registered trademarks of their respective corporations®WIRELESSKEYLESS ENTRYUSER'S INSTRUCTIONS(Model 89)FCCThe Universal Garage Door RemoteControl is approved by the FCCand it complies with Part 15 of theFCC Rules. Its operation is subjectto the following two conditions :1. This device may not causeharmful interference.2. This device must accept anyinterference that may causeundesired operation.WARNING:Changes or modifications to this unitnot expressly approved by the partyresponsible of compliance could voidthe user’s authority to operate theequipment.2a. The Model 89 contains 2 brand jumpers and 12 DIPswitches (see diagram B). The brand jumpers arelocated just above the DIP switches with markings “A”and “B”. There are 2 connectors, one is placed onthe “A” column, the other one is placed on the “B”column. For each column, there is a connector. Ifthe connector is placed on the top and middle post ofthat column, that column is set on “+”. If the connectoris placed on the middle and bottom posts, that columnis set on “-“. If the connector is removed completely,that column is set on “0” (see diagram B). In order forthe Model 89 to work with your existing garage dooropener (motor), you need to set the brand jumpersbased on the brand of your existing garage dooropener. Please set these 2 brand jumpers “A” and“B” based on the brand jumpers setting on chart 2.STEP 2 - SET BRAND JUMPERS

Navigation menu